Is it possible to do conforence call by coding any help please
Hi,
can we convert incoming or out going call as a cofirence call by coding
Thanks,
Sandeep,
means if i get a call, by selecting my app,call should go for few more people and make confirence call with them
Similar Messages
-
When I disconnect my iPhone 4s from the charger, it gives me the dial pad with a emergency call option... help please?
Hello there, curtq.
Great job troubleshooting your issue so far. The following Knowledge Base article offer some great practical steps for troubleshooting Wi-Fi issues with your iOS device:
iOS: Troubleshooting Wi-Fi networks and connections - Apple Support
If following the initial troubleshooting steps recommended at the beginning of the article, you may want to then proceed to:
Unable to access the Internet while connected to Wi-Fi
If you're using a public or commercial network, you may need to log in or subscribe.
Check to see if you have a self-assigned IP address:
Tap Settings > Wi-Fi and locate the Wi-Fi network to which you're connected and tap .
If your IP address is 169.254.xxx.xxx, you may not be able to access the Internet.
If you do not have a self-assigned IP address, see if other Wi-Fi devices on your network have Internet access.
If they do not, consult with your network administrator or ISP for further assistance.
If they do, reset network settings on your device by tapping Settings > General > Reset > Reset Network Settings. Note: This will reset all network settings including:
previously connected Wi-Fi networks and passwords
recently used Bluetooth accessories
VPN and APN settings
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro. -
When i call someone, the other person hears echo of his own voice.This happens all the time in all locations.
I am using STC network in Saudi arabia.(KSA) but i have also tried this using other networks in KSA and also with networks in INDIA.
Any help would be highly appreciated. ??When i call someone, the other person hears echo of his own voice.This happens all the time in all locations.
I am using STC network in Saudi arabia.(KSA) but i have also tried this using other networks in KSA and also with networks in INDIA.
Any help would be highly appreciated. ?? -
I can no longer use my phone for calling or texting. Help please?
Every time I send a text, a message pops up immediately saying; "Error". It also pops up instantly whenever I press retry. Another issue is when I try to call from the phone, it says; "Emergecy Calls Only". I know it's nothing to do with credit because I've tried calling the free Orange numbers (450, 453 etc.) and it still says the same thing. Any help would be appreciated.
This normally happens if your sim card or mobile is faulty or if there is an issue with the signal where you are.
have you tried turning the phone off, removing the battery and sim card, give the contacts a quick wipe with a lint free cloth and try again.
You could also try live chat, or an experienced member of the team will be around at some stage and my have another answer for you -
Calling a method, some help please
Hi, I'm trying to run or call a method in my main Class which has received a StringBuffer value from another method in a separate class. I'm unsure about how to call this particular method. The way the method works is receiving some XML packets from a ConnectionBean. I'm just testing it so far to output the stuff in my Terminal window.
//Method to call in <body> of XML contained in a StringBuffer
public StringBuffer updateEditor( StringBuffer body ) {
StringBuffer sbuff;
sbuff = communicate.incomingBody( body );
System.out.println( "main received" + sbuff );
return sbuff;
How would I call this method which is already in my main Class (that has all the GUI elements). I just want this method to run when a value is received/passed into it. So really it needs to be running all the time - in effect listening to received StringBuffers.
Thanks :)I wasn't clear, sorry I'll show you what I have:
A Class named Comms that has two methods sorting out the XML stuff:
Class Comms {
//Handles history of incoming <body> XML from receievedPacket
protected void addToHistory( Message msg ) {
//Build String to append
StringBuffer sb = new StringBuffer();
sb.append( msg.getBody() );
incomingBody( sb );
System.out.println( sb );
//Stores the StringBuffer value from addToHistory
public StringBuffer incomingBody( StringBuffer sb ) {
StringBuffer body;
body = sb;
if( body != null ) {
System.out.println( body );
return body;
....//End Class
And the main Class ( Exchange) that does the GUI stuff and I've a method that calls in the incomingBody(); method. I've already created a new instance of that class:
Class Exchange {
Comms communicate = new Comms();
//And then the method that I want to be called
//Method to call in <body> of XML contained in a StringBuffer
public StringBuffer updateEditor( StringBuffer body ) {
StringBuffer sbuff;
sbuff = communicate.incomingBody( body );
System.out.println( "main received" + sbuff );
return sbuff;
I'm not sure how to call/run this method in the main Class (Exchange) all the time so that it checks the other Class' method incomingBody?
Thanks -
Hi Guys,
I have a SIP trunk setup with a 2811 running CME version 7. I can make outbound calls ok but having issues getting the incoming calls working, i have 1 number on my SIP trunk and that is 01133501788 and i want that to ring my Cisco 7960 which is running SIP firmware not SCCP. I have included by config for anyone who can help me, i just want the incoming call to work.
Many Thanks.
Matthew.
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
logging message-counter syslog
no aaa new-model
clock timezone GMT 0
dot11 syslog
ip source-route
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.1.1
ip dhcp excluded-address 10.10.10.1
ip dhcp pool DATA_POOL
network 10.10.10.0 255.255.255.0
default-router 10.10.10.1
dns-server 188.92.232.50 188.92.232.100
ip dhcp pool VOICE_POOL
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 188.92.232.50 188.92.232.100
option 150 ip 192.168.1.1
ip name-server 188.92.232.50
ip name-server 188.92.232.100
no ipv6 cef
multilink bundle-name authenticated
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
no supplementary-service sip moved-temporarily
no supplementary-service sip refer
sip
bind control source-interface FastEthernet0/1.20
bind media source-interface FastEthernet0/1.20
registrar server
voice class codec 1
codec preference 2 g711ulaw
codec preference 3 g711alaw
voice register global
mode cme
source-address 192.168.1.1 port 5060
max-dn 144
max-pool 42
load 7960-7940 P0S3-8-12-00
authenticate register
tftp-path flash:
create profile sync 0008072514198272
voice register dn 1
number 6999
allow watch
name SIP
label SIP
voice register pool 1
id mac 000F.902B.40E0
type 7960
number 1 dn 1
dtmf-relay sip-notify
username cisco password cisco
codec g711ulaw
voice translation-rule 1
rule 1 /^9\(.*\)/ /\1/
voice translation-rule 2
rule 1 /^6...$/ /4143*002/
voice translation-profile DiscardDigit9
translate calling 2
translate called 1
voice translation-profile IncomingSIP
translate calling 1133501788
voice-card 0
no dspfarm
username matt privilege 15 secret 5 $1$DCD0$SjWqnKgDSGVzzIKRerXh11
archive
log config
hidekeys
interface FastEthernet0/0
ip address 194.12.0.222 255.255.255.252
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
interface FastEthernet0/1
no ip address
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
interface FastEthernet0/1.10
description DATA
encapsulation dot1Q 10
ip address 10.10.10.1 255.255.255.0
ip nat inside
ip virtual-reassembly
interface FastEthernet0/1.20
description VOICE
encapsulation dot1Q 20
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 194.12.0.221
ip http server
ip http authentication local
no ip http secure-server
ip nat inside source list 1 interface FastEthernet0/0 overload
access-list 1 permit 192.168.1.0 0.0.0.255
access-list 1 permit 10.10.10.0 0.0.0.255
tftp-server flash:P003-8-12-00.bin
tftp-server flash:P003-8-12-00.sbn
tftp-server flash:P0S3-8-12-00.loads
tftp-server flash:P0S3-8-12-00.sb2
tftp-server flash:P003-8-12-00
tftp-server flash:P003-8-12-00.loads
tftp-server flash:P003-8-12-00.sb2
tftp-server flash:SIP000F902B40E0.cnf.xml
control-plane
mgcp behavior g729-variants static-pt
dial-peer cor custom
dial-peer voice 2 voip
description Outgoing Geographic
translation-profile outgoing DiscardDigit9
destination-pattern 0[7]........
voice-class codec 1
session protocol sipv2
session target dns:sip.cloudcalling.co.uk
dtmf-relay rtp-nte
no vad
dial-peer voice 1 voip
description IncomingSIP
translation-profile incoming IncomingSIP
voice-class codec 1
session protocol sipv2
session target dns:sip.cloudcalling.co.uk
incoming called-number .T
dtmf-relay sip-notify rtp-nte
no vad
sip-ua
credentials username 4143*002 password 7 password realm sip.cloudcalling.co.uk
authentication username 4143*002 password 7 password
nat symmetric role passive
nat symmetric check-media-src
calling-info sip-to-pstn number set 4143*002
no remote-party-id
retry invite 3
retry register 3
timers connect 100
registrar dns:sip.cloudcalling.co.uk expires 60
sip-server dns:sip.cloudcalling.co.uk
host-registrar
gatekeeper
shutdown
telephony-service
load 7960-7940 P0S3-8-12-00
max-ephones 24
max-dn 30
ip source-address 192.168.1.1 port 2000
max-conferences 8 gain -6
web admin system name Admin secret 5 $1$Fktw$t9GQkdDdHmoYdwptO8.or.
transfer-system full-consult
create cnf-files version-stamp Jan 01 2002 00:00:00
line con 0
line aux 0
line vty 0 4
login
scheduler allocate 20000 1000
ntp server 85.119.80.232
end
Router#You my friend are a star! worked straight away, many thanks. Just one more thing, when i make an outgoing call, it always appears as "blocked" on my phone, my sip trunk is set to allow CME to alter outgoing CLI's how would i program the outgoing CLI to 01133501788 also?
The new working config is below with your suggestion, which works!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
logging message-counter syslog
no aaa new-model
clock timezone GMT 0
dot11 syslog
ip source-route
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.1.1
ip dhcp excluded-address 10.10.10.1
ip dhcp pool DATA_POOL
network 10.10.10.0 255.255.255.0
default-router 10.10.10.1
dns-server 188.92.232.50 188.92.232.100
ip dhcp pool VOICE_POOL
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 188.92.232.50 188.92.232.100
option 150 ip 192.168.1.1
ip name-server 188.92.232.50
ip name-server 188.92.232.100
no ipv6 cef
multilink bundle-name authenticated
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
no supplementary-service sip moved-temporarily
no supplementary-service sip refer
sip
registrar server
voice class codec 1
codec preference 2 g711ulaw
codec preference 3 g711alaw
voice register global
mode cme
source-address 192.168.1.1 port 5060
max-dn 144
max-pool 42
load 7960-7940 P0S3-8-12-00
authenticate register
tftp-path flash:
create profile sync 0015244443466064
voice register dn 1
number 6999
allow watch
name SIP
label SIP
voice register pool 1
id mac 000F.902B.40E0
type 7960
number 1 dn 1
dtmf-relay sip-notify
username cisco password cisco
codec g711ulaw
voice translation-rule 1
rule 1 /^6...$/ /4143*002/
voice translation-rule 3
rule 1 /^01133501788$/ /6999/
rule 2 /^1133501788$/ /6999/
voice translation-profile IncomingSIP
translate called 3
voice translation-profile Translatetrunk
translate calling 1
voice-card 0
no dspfarm
username matt privilege 15 secret 5 $1$DCD0$SjWqnKgDSGVzzIKRerXh11
archive
log config
hidekeys
interface FastEthernet0/0
ip address 194.12.0.222 255.255.255.252
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
interface FastEthernet0/1
no ip address
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
interface FastEthernet0/1.10
description DATA
encapsulation dot1Q 10
ip address 10.10.10.1 255.255.255.0
ip nat inside
ip virtual-reassembly
interface FastEthernet0/1.20
description VOICE
encapsulation dot1Q 20
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 194.12.0.221
ip http server
ip http authentication local
no ip http secure-server
ip nat inside source list 1 interface FastEthernet0/0 overload
access-list 1 permit 192.168.1.0 0.0.0.255
access-list 1 permit 10.10.10.0 0.0.0.255
tftp-server flash:P003-8-12-00.bin
tftp-server flash:P003-8-12-00.sbn
tftp-server flash:P0S3-8-12-00.loads
tftp-server flash:P0S3-8-12-00.sb2
tftp-server flash:P003-8-12-00
tftp-server flash:P003-8-12-00.loads
tftp-server flash:P003-8-12-00.sb2
tftp-server flash:SIP000F902B40E0.cnf.xml
control-plane
mgcp behavior g729-variants static-pt
dial-peer cor custom
dial-peer voice 1 voip
description IncomingSIP
translation-profile incoming IncomingSIP
voice-class codec 1
session protocol sipv2
session target sip-server
incoming called-number .T
dtmf-relay sip-notify rtp-nte
no vad
dial-peer voice 2 voip
description Outgoing Geographic
translation-profile outgoing Translatetrunk
destination-pattern 0[7]........
voice-class codec 1
session protocol sipv2
session target dns:sip.cloudcalling.co.uk
dtmf-relay rtp-nte
no vad
sip-ua
credentials username 4143*002 password 7 password realm sip.cloudcalling.co.uk
authentication username 4143*002 password 7 password
nat symmetric role passive
nat symmetric check-media-src
calling-info sip-to-pstn number set 4143*002
no remote-party-id
retry invite 3
retry register 3
timers connect 100
registrar dns:sip.cloudcalling.co.uk expires 60
sip-server dns:sip.cloudcalling.co.uk
host-registrar
gatekeeper
shutdown
telephony-service
load 7960-7940 P0S3-8-12-00
max-ephones 24
max-dn 30
ip source-address 192.168.1.1 port 2000
max-conferences 8 gain -6
web admin system name Admin secret 5 $1$Fktw$t9GQkdDdHmoYdwptO8.or.
transfer-system full-consult
create cnf-files version-stamp 7960 Dec 17 2013 14:35:13
line con 0
line aux 0
line vty 0 4
login
scheduler allocate 20000 1000
ntp server 85.119.80.232
end
Router# -
Wifi calls not working anymore help please
Hi ,
Welcome to the Community.
Please get in touch so our technical team can help.
Click here for contact details.
Thanks
JamesHi James thanks for the advise I tried calling them yesterday and they ran me through loads of tests to do and still don't have wifi calls as they have said either a problem with carrier settings or ios8.4 and might have to wait for Apple to do an update before it works for me again not happy as I rely on wifi calls as I have no signal at work or at home without it.
-
I have recently been given an iPhone 4, and I put in my old t-mobile simcard. It says that I have signal but i can't send/recieve calls and texts. Is there anyway this can be fixed?
is the "old" T mobile sim an iPhone micro sim or something else ,
if so that is likely your issue -
I've had the phone for 3 onths but this this just happened recently. I called it on my wifes phone and it does sound like I have acloth over the phone when I am talking. I went thru all the steps Verizon has posted to resolve this, Safe MOde. It even did it in Safe Mode. No one can understand whay I am saying. this really sucks.
This happened to my son once, on a different model phone. It was about 3 weeks old and I brought it to verizon fully prepared to argue that it was defective and I didn't want a "refurb" replacement. The guy behind the counter blew air through the back of the phone and some fuzz flew out. I felt pretty stupid...lol. Anyway, this phone, the Galaxy s3 has 2 microphones (regular and noise cancelling)....tiny little pinholes, one on the top and one on the bottom. I don't know how to tell you how to clear them since sticking a pin up in them might do more damage and not dislodge something if that is the problem. I just looked at my phone and it doesn't look easy as the plastic under the regular backing is secured down with screws. If you are bold and brave, you might try carefully removing that to look and see if you can blow through the mic hole from that direction? Honestly, I don't want to tell you to do anything that could harm your phone, but if it was me, I would.
-
I'd like to connect my iPhone 4s using ios5.0.1 with my iPad 3 using ios6.0.1 via bluetooth so i can send photos without sync to my pc.when i activate BT no one can find the other.why?
You need a third-party app to do so, like this:
https://itunes.apple.com/us/app/bluetooth-u-share-files-photo/id526268815?mt=8
There are a number of apps in the app store like this. -
Is it possible to MANUALLY change Display Resolution (screen size) HELP!!
Forgive me if this has been covered already, but I have tried to look here and
there for an answer
My screen for my iMac-G4 blew out long ago, I had a another screen (a Dell CRT-
flatscreen) hooked up and IT blew out a few days ago, I just bought an LCD
flat screen, but it needs a 1680 x 1050 resolution (WIDE screen(?)and my
iMac-G4 only goes to 1024 x 768 in the "Display" controls. So all my desktop
images are "scrunched" or "stretched".
So is there a "MANUAL" way of configuring the screen size to a "standard"
size within this Mac? or do I need to find a standard size screen?
. . . HELP!!!
You can also write me (preferably at) at:
[email protected]
I VERY MUCH appreciate any help- please realize too, that I am an IDIOT when it
comes to computers, I just paint on this thing (as part of my job as a freelancer
on the side), and WAS in the middle of a job for a client
Thanks again,
-MAVIIIHello and Welcome to Apple Discussions.
Apple limited the graphics cards in iMac G4s to the native resolution of the built-in LCD i.e:
15" iMac G4 - 1024 x 768
17" iMac G4 - 1440 x 900
20" iMac G4 - 1680 x 1050.
Even when connecting a second display this could only mirror the internal at the same resolution. For the following iMac G4's it's possible to install a firmware hack to open up the full capabilities of the graphics cards:
17" 800MHz
17" 1GHz
15" 1GHz
17" 1.25GHz
20" 1.25GHz
using an application called Screen Spanning Doctor. This is risky but I guess you haven't got much to lose at this point. I've only ever heard of one Mac user actually failing to do the process right though.
You can always use Firewire Target Disk Mode to recover you client's files to another Mac.
I'd be interested if SwitchResX works too. I only have external displays much smaller than my iMacs so can't test it from that perspective.
cheers
mrtotes -
Since i update my iPhone 5 with IOS 7.0.2, I start to have serious problems to call or receive calls from other telephones: is not possible to open the call at the first try. Somebody have the same problem?
Try
Reset: Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Note: You will not lose any data -
can i use internet in my ipad 3g ios 5.1 through my iphone sim also possible to make voice calls
and i can't fine any access pint name changing option in ipad plz help meYou might be able to use your iPhone sim. FaceTime calls are only possible over wifi or you can get something like the Skype For iPad app from the store if you want to make video calls over 3G - but you can't do 'normal' phone calls with the iPad.
-
Portege R600 - Is it possible to make a call with the SIM?
Hi,
I wonder if its possible to use the Wireless connection manager 5 and to make or receive a call?Hi,
I see that nobody answered so i will try to explain what i meant -
Is it possible to make audio call with the Wireless Manager by the GSM modem module?
I succeed to send SMS and to connect to HSPA data services but i dont find any reason why i can not connect to the GSM and make a call.
I have Portege R600 model PPR61E-01C00NG3
I even succeed to use the GPS that probably installed in the GSM/HSPA modem (wireless manager 5).
If anyone can explain how and if it possible to make a call please send your reply ... i wnat to use the laptop with BT instead of cell phone ....
Thanks
Yan -
When I try to call voicemail it says it has not been possible to connect your call! But if I dial 222 it acts as if my voicemail is set up but if someone calls me it isn't!
Anyone can help me please? I'm on 'EE' networkOn iPhones the setup is an OS feature.
U got to phone -> voicemail -> setup.
It'll set it up for u. But some times it doesn't let u set it up and doesn't let u access it via the iPhone voice mail feature. This is the problem.
Maybe you are looking for
-
Ipod dialog comes up " . . will not read or write to disk"
Strange! Right after uploading the ITunes upgrade of 7.1.1, I can't complete syncing my ipod. Same problem on my 30gb and 80gb. There is plenty of room on the ipod disk, but the download always stops short and the dialog box comes up on my Mac. I've
-
Need your advice about image creation
Hi, I am trying to create image of my c partition on Satellite A100-529 - no luck. Norton ghost freezes (booted from DOS) just after start, g4l cannot load (kernel panic), partimage, being a part of SystemRescue CD package does not see the hd drive!
-
What application can you use to open a file with the .acc extension?
What application can you use to open a file with the .acc extension?
-
Setting an job for closing settled process orders
Hi PP Gurus, I have a requirement to set a background job to close the process orders that have been settled and have not been modified with a certain time frame. Are there any standard programs which support this requirement of influencing the selec
-
Hello, I'd like to know when I bought my I pod touch 4th g. can I know?