Is it possible to manage the switch SMB 300 series using Cisco Prime Infrastructure?
Is it possible to manage the switch SMB 300 series using Cisco Prime Infrastructure 1.2?
SF300 series is targeted for support in PI 2.0.
Similar Messages
-
Adding new switch in my network including Cisco Prime Infrastructure
hi all,
if I connect new switch to my network, can I let Cisco PI to apply a specific template of configuration to this switch automatically?
how can I do that ?
thanks in advanceHi,
i followed these steps :
SWITCH SIDE
- configured Prime Infrastructure as snmp-server host;
- enabled snmp-traps for linkup and linkdown events globally;
- disabled snmp-traps for linkup and linkdown on non relevant interfaces using the no snmp trap link-status command
PRIME INFRASTRUCTURE SIDE
- under "Deploy/Monitor Deployment" i deployed template "Interface Health" for all the interested switches
- under "Administration/System Settings/Mail Server Configuration" configured my internal SMTP server to make Prime Infrastructure able to send e-mails
- under "Operate/Alarms & Events" click on "Email Notifications" , then on "Switches and Hubs"
- check the "critical" box , insert the destination e-mail address into the "To" field then click "Save"
- check the "switches and Hubs" box and then click Save
As i know is possible to avoid to configure every single not-interesting port on the switches with "no snmp trap link-status" command (it's a bit annoying when you have tens of switches), using Port Grouping configuration on PI but i tried it without success.
Hope this helps.
Best Regards, -
Cisco Prime Infrastructure 2.0 Alarms (switch port down)
We have a cisco Prime Infrastructure 2.0 managing switches, routers and AP.
By default, when a port of a switch goes down, the cisco Prime Infrastructre generates a Critical Alarm for that. (this is a problem, because every phone of laptop disconnection will generate a critical alarm for me)
I found out that if we go to Administration --> Alarm Severity --> Link down, I can change the Alarm from Critical to another type of alarm.(ex: warning)
The problem is that I want to keep the Critical Alarm for my Uplinks ports and for some important switch ports, and I would like to make the alarm as warning for the normal user ports.
I know that I can create Port Groupping and add ports to each group and apply monitoring templates on those groups. But This couldn't Help me solving my alarm problem.
So I just need to know how to manage the alarms severity for each group of ports.
Thank youHi,
Same problem here.
I am using Cisco Prime Infrastructure 2.0 (evaluation version for 60 days). I want to deploy port monitoring for my trunk ports between switches and some other important ports e.g. servers. Basically I want to get alarms when these ports are down, there are errors on ports and etc.
So in Design>Port Grouping I created User Defined group with important ports. In Deploy>Monitoring Deployment I selected Interface Health (default)>Deploy selected Port Groups and when selected port group I created.
Now the rule shows Deployed: Yes and Status: Active. After that I just pulled out one port which was in monitored group, waited 5min as it is set in Interface Health (default) template, and nothing happened, and worse, alarms started to show up of other ports where regular users are connected (computers was turned off), which I do not want to see at all. I tried redeploy template, I even created my own template but still no desired result.
Any suggestions how to make port monitoring work? -
Cisco Prime Infrastructure 2.0 not showing alerts from switch
Hello,
I have a prime infrastructure 2.0 running at a customer place and the customer now complains that he is not receiving link up/down messages from the switch. When i checked I have seen that if I shut down a port in the switch the prime identifies after a long time, but its not generating an alarm still. How can I fine tune the prime to fix this issue. Please help on this.
Thanks in advanceHi,
Same problem here.
I am using Cisco Prime Infrastructure 2.0 (evaluation version for 60 days). I want to deploy port monitoring for my trunk ports between switches and some other important ports e.g. servers. Basically I want to get alarms when these ports are down, there are errors on ports and etc.
So in Design>Port Grouping I created User Defined group with important ports. In Deploy>Monitoring Deployment I selected Interface Health (default)>Deploy selected Port Groups and when selected port group I created.
Now the rule shows Deployed: Yes and Status: Active. After that I just pulled out one port which was in monitored group, waited 5min as it is set in Interface Health (default) template, and nothing happened, and worse, alarms started to show up of other ports where regular users are connected (computers was turned off), which I do not want to see at all. I tried redeploy template, I even created my own template but still no desired result.
Any suggestions how to make port monitoring work? -
Possible to manage the MobileMe galleries made by iPhoto using Aperture3?
I am considering moving my whole library from iPhoto to Aperture.
I understand that I can import the whole iPhoto library, but is it also possible to manage the existing MobileMe galleries made by iPhoto using Aperture3, without changing the current URLs of the gallery?
Thanks.I'd like some info on this also.
Currently I have iphoto publishing photos to Facebook, Mobileme and Flickr. I have imported my iphoto library but none of these folders have imported. Is there a clever way of transferring these over to Aperture (3) such that my mobilem is unaffected as is my Flickr and facebook.
Aperture 3 already see's my mobileme and I posted a new album to mobileme from Aperture wondering if that would force it to download the other albums on there already but it didn't. You would think there is a way to do this. Otherwise if I have to delete the links in iphoto to facebook and then repost them from Aperture they will show as completely new uploaded photos when a lot of them are years old and at a guess it will re-tag all my contacts who will all think there are new photos of them.
Likewise will all my flickr comments be lost in the above process and will I effectively be starting from scratch again?
Any thoughts, ideas, help and guidance would be very much appreciated. I'd like to get away from using both iphoto and Aperture to just using Aperture 3 now it has all the additional functionality of faces that I like to use.
Thanks -
hi i have a iphone5 I lost my password ha possibility I make the switch for 5s can not open the icloud?? if accepted as pay the difference? thank you for it helped.
Post in your native language. Your post is very difficult to understand. What password are you talking about? You device passcode? Your Apple ID password?
-
How do I use the time capsule to share itunes music between multiple apple devices? Also, is it possible to control the music on one device using another, and how do you set this up?
unless i'm missing something, i think you got mixed up, this is easy google for walk throughs
i'm assuming this is the new 3tb tc AC or 'tower' shape, if so, its wifi will run circles around your at&t device
unplug the at&t box for a minute and plug it back in
factory reset your tc - unplug it, hold down reset and keep holding while you plug it back in - only release reset when amber light flashes in 10-20s
connect the tc to your at&t box via eth in the wan port, wait 1 minute, open airport utility look in 'other wifi devices' to setup the tc
create a new wifi network (give it a different name than your at&t one) and put the tc in bridge mode (it may do this automatically for you, but you should double check) under the 'network' tab
login to your at&t router and disable wifi on it
add new clients to the new wifi network, and point your Macs to the time machine for backups -
Hello. I want to use my iphone as a viewing screen for a usb endoscope, (its a small camera on a long cable for inspecting down piping and such) with your app is it possible to attach the usb to my iphone using a adapter to watch the live video feed on the iphone?
Thankyou.Hello. I want to use my iphone as a viewing screen for a usb endoscope, (its a small camera on a long cable for inspecting down piping and such) with your app is it possible to attach the usb to my iphone using a adapter to watch the live video feed on the iphone?
Thankyou. -
Is it possible to hide the save function and only use the save as function in teststand
Hi,
When i'm done building a sequence i want to prevent other engineers to save the sequence with the same filename (or version number).
Is it somehow possible to "hide" the save button and only use the save as function?
Or is there another possiblity to solve my problem.
The idea is to have a sequence called Sequence_V1.0.seq which i have build. When installing this in a factory enviroment I would like whenever there is a change needed in the sequence that the version number increases (manual action) (becomes Sequence_V1.1.seq). So from the moment you want to save i would like to only have the function save as. In this way you are obligated to fill in a new sequence name (original sequence will be read-only)
What would even be great if there could be a log of what the changes were
Thx!!!1) You could mark the file as read-only, by default you would then not be able to save over it. The user could make it not read-only though if they know what they are doing.
2) Another possibility is to lock the sequence file for editing (this is a teststand feature). Go to the Sequence File Property dialog, on the advanced tab, where it says Password Protection, set it to Not Editable and give it a good password. This doesn't however keep someone from saving another file to the same name as the locked one, but they at least won't be able to saved the locked file again without your password, nor will they be able to edit it.
Hope this helps,
-Doug -
Is it possible to sort the Aperture Library by Lens used
Is it possible to sort the Aperture Library by Lens used? And get statistics on the different Lenses used?
I'm using latest Aperture.I would just add that your Preferences settings have to be set to show the columns you need. Go to Aperture -> Preferences, and select the Metadata tab. in the "List View Columns" field, for whichever set you have chosen with the radio button, choose the set of data from the pulldown list that shows the fields you want. For example, I have the lens model field set in EXIF-Expanded set. I choose that set and those fields will show in the columns in List View.
Great tips, thanks! -
My Cisco Prime Infrastructure ver. 1.2.1.12
Cisco Prime Infrastructure - I can't see the hardware virtual image when I selected a device managed by Prime Infrastructure. See attached picture.
Please let me know how to access or enable the feature.
Thanks,
TekThis is by no means a full solution, but deleting and re-adding only takes a few minutes if you use the "Export Device" and "Bulk Import" features from the Device Work Center. You can export the desired devices to a CSV file, delete them, then import from the CSV.
Of course, you might lose historical data when deleting the devices, but I'm guessing that's not as relevant since the devices themselves have been replaced by different hardware. -
Ask the Expert: Cisco Prime Infrastructure - Implementation and Deployment
Welcome to the Cisco Support Community Ask the Expert conversation.
This Ask The expert Session will cover questions spanning Cisco Prime Infrastructure on Implementation and Deployment on Wired and Wireless. This will be more specific to Customer’s and Partners questions product covering PI on configuration, Features and Menu, Network Monitoring, Maps, Implementation, High Availability and Maintenance and t/s parts.
Monday, February 2nd, 2015 to Friday, February 13th, 2015
Dhiresh Yadav is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco Prime Infrastructure and Cisco Wireless products. He has over 7 years of industry experience working with large enterprise and service provider networks. He also holds CCNP (RS) and CCIE (DC) certifications.
Afroz Ahmad is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco NMS products like Prime Infrastructure, LMS, IP SLA and SNMP etc. He has over 7 years of industry experience working with large enterprise and service provider networks. He also holds CCNP (RS),CCIE (DC), and SCJP (Sun Certified Java Professional )
Vinod Kumar Arya is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco NMS products like Prime Infrastructure, LMS, IP SLA and SNMP etc. He has over 8 years of industry experience working with large enterprise and service provider networks. He also holds VCP 5 and RHCE certifications.
** Remember to use the rating system to let the experts know you have received an adequate response.**
Because of the volume expected during this event, the experts might not be able to answer every question. Remember that you can continue the conversation in the Network Infrastructure community, > Network Management, shortly after the event. This event lasts through February 13th 2015. Visit this forum often to view responses to your questions and those of other Cisco Support Community members.Hello Wilson,
Thanks for joining us.
1841 should just work fine for net flow . Hope you have a valid "PI Assurance license" installed on the server.
"PI Assurance license" is required for "net-flow" feature
Devices supporting Netflow in PI ::
1400, 1600, 1700 & 1800
2500, 2600 & 2800
3600, 3700, 3750 & 3800
4500 & 4700
AS5300 & 5800
7200, 7300, 7400 & 7500
Catalyst 4500 ASCI
Catalyst 5000, 6500, & 7600 ASCI
ESR 10000 ASCI
GSR 12000 ASCI
Cisco IOS Software Release Version
Supported Cisco Hardware Platforms
11.1CA, 11.1CC
Cisco 7200 and 7500 series, RSP 7200 series
12.0
Cisco 1720, 2600, 3600, 4500, 4700, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series
12.0T, 12.0S
Cisco 1720, 2600, 3600, 4500, 4700, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8600 series
12.0(3)T, 12.0(3)S
Cisco 1720, 2600, 3600, 4500, 4700, AS5300, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8650 series
12.0(4)T
Cisco 1400, 1600, 1720, 2500, 2600, 3600, 4500,
4700, AS5300, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8650 series
12.0(4)XE
Cisco 7100 series
12.0(6)S
Cisco 12000 series
NetFlow is also supported by these devices Cisco 800, 1700, 1800, 2800, 3800, 6500, 7300, 7600, 10000, CRS-1 and these Catalyst series switches: 45xx, 55xx, 6xxx.
NetFlow export is also supported on other Cisco switches when using a NetFlow Feature Card (NFFC) or NFFC II and the Route Switch Module (RSM), or Route Switch Feature Card (RSFC). However, check whether version 5 is supported, as most switches export version 7 by default.
You can check the below steps to diagnose the issue::
To verify that NetFlow is exported from a device to PI, follow the steps below:
1) Browse to Administration > Data Sources page. Check the value in column ‘Last Active Time’ for the ‘Device Data Sources’ table. If the table is empty or the value does not represent recent time, then
it is possible that the device is not exporting NetFlow or PI Assurance license is not applied / expired.
2) Login to PI console ( via SSH) as root user and run the command:
netstat –an | grep 9991 – Output of this should be like : udp 0 0 :::9991 :::*
Check the firewall settings on PI server using the command: firewall -L
1) Check the configuration on an IOS / IOS –XE device. Run the commands
a) sh running-config | inc destination
1) This should list the IP address of the PI SERVER ( along with other outputs if any)
b) sh running-config | inc 9991
1) This should list at least one entry.
c) If the above are fine, then verify that the flow monitor, flow exporter and the flow records are correctly configured on the device.
Refer to the URLs below to configure NetFlow export.
http://preview.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/2.0/user/guide/setup_monitor.html#wp1056427
Thanks-
Afroz
***Ratings Encourages Contributors **** -
How to mornitor VSS (Virtual Switching System) & Stack (Switch) By Cisco Prime Infrastructure
Dear all,
I have 02 C6504-E with VSS (Virtual Switching System)
and 02 C3750X-24T-L used Stack
How to you Cisco Prime Infrastructure to monitor VSS & Stack tatus?
Thanks.Virtual Switching technology is the process of combining two standalone distribution switches found in the local distribution layer into a single management point.
The Virtual Switching System functions and appears as a single switch to the wiring closet and the core layer. You can also create Virtual Switching Systems with a pair of standalone switches available in the core layer.
For configuration please check the below link:
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.1/user/guide/configuration/configvss.html#wp1042960 -
What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP's?
What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP’s?
• PI provides visibility for autonomous clients within the same list view as lightweight and wired clients (client list page).
• Rogue AP detection for autonomous AP's is not supported (it's supported in CUWN).
• Alarms/events for client authentication issues (e.g. authentication failure) are displayed in PI.
• Config management for autonomous AP's is via CLI template. Config comparison and archiving functionality in PI leverages these same features that were brought in from LMS, so need to defer to others in terms of whether this is a cross-platform feature in PI or is only supported on a subset of platforms. Config comparison/archive is supported in CUWN.PI supports both infrastructure (e.g. AP Tx Power and Channel, busiest AP, AP utilization, etc.) and client (e.g. client count, client sessions, etc.) reports, and there are extensive reports for CUWN -
Cisco Prime Infrastructure - Is there a report of unused switch ports?
Hello,
Is there a report in Cisco Prime Infrastructure 1.4 showing the unused switch ports?
There used to be one in Cisco Prime LMS (Reclaim Unused Up/Down Ports Report).
Thank you,
LukeHello,
I now have Cisco Prime Infrastructure 2.0 running, and I don't see a report like the "Reclaim Unused Up/Down Ports" report that existed in LMS.
I found one called "Interface Capacity", but it only shows the number of ports that are "connected", "notconnect" or "disabled".
Does anyone know if a report of Unused ports exists in Prime Infrastructure 2.0 or if it will be available later on?
Thank you,
Luke
Maybe you are looking for
-
How to get the actual path of a file present in the Web content folder
I have a jasper file which is present inside the Web-Content folder of my project. I need to pass this file as an argument to the FileInputStream object. How can i give the actual path of the jasper file, since this project can be deployed anywhere e
-
Saving a series of images (from a smart camera) into an AVI file
Hello, I have a lab setup in which we view brain cell deflections in a well-plate after being pressurized with air for 50ms. I have a smart camera hooked up to an IMAQ PCI card to acquire images. I'm trying to save the series of images into an avi fi
-
Apple 30-pin adapter for my iPhone 4 and iPod doesn't work
I purchased an Apple 30-pin adapter for my iPhone 4 and iPod touch to connect an HDMI cable to my HDTV. I am able to get audio but no picture. Any suggestions as to what the problem may be?
-
Automatic AP/ AR posting with different amount in Non-Leading Ledger
Dear All, We have leading ledger for local GAAP and Non leading for IFRS. Is there any configuration/ mechanism to post a AP/ AR document with relevant amount in the Non-Leading Ledger based on the a/cing standards described by relevant standard. I a
-
Using wliconsole's process instance monitoring and audit trail
Hello, I have couple of questions about wliconsole's process monitoring capabilities to be able to use in real production environments. 1. Is it possible to add some custom data to the Process Instance Summary table? For example, we would like to sho