Is it possible to to disconnect 2 wireless clients from my wireless network without access to the clients i.e. 2 iPads?

Is it possible to disconnect 2 wireless clients from my network if I do not have access to the clients? ie 2 iPads.

You would have to set up Timed Access for each device.
This consists of specifying the amount of time each day that wireless devices will be allowed to connect to the network. You must provide a MAC or hardware address for each device, which is a long code that might look something like this, for example......A1-B2-C3-D4-E5-F6....and then specify the hours each day that this device is allowed to connect to the wireless network.
You have to do this for each device, which is tedious. Devices that are not on the Access List cannot connect to the network at any time.

Similar Messages

Airplay from itunes to zepplin air will disconnect my computer from my wireless network

Hi there,
Relatively new subject matter, so haven't been able to find much online...
I recently purchased a Zeppelin Air - for those who don't know its an ipod speaker system with airplay built in. I'm running a Windows Vista x64 machine with the latest version of iTunes.
When I open up iTunes and go to play a song, everything works fine for about 30 seconds and then the audio stops and my computer disconnects from my network. My network icon in the system tray shows disconnected and of course a new browser window won't open my home page.
I then tried using a program called Airfoil to stream Spotify to my Zepplin speakers and it works fine. Go back to itunes to test out (streaming from itunes now, and not the Airfoil program) and it makes it past a minute, but then after a few minutes it starts getting choppy. I press stop and start another song... a whole song finishes. Next song about a minute in it disconnects my computer from my home network again.
Next I open up Airfoil and have it hijack itunes rather than using the airplay feature in itunes. I make it a few minutes into one song, decide to skip to another, no problem. No disconnects.
Back to itunes, no airfoil this time, back to using the airplay feature from itunes. 25 seconds into a song, it gets really choppy, drops audio. I press stop and try another song... really choppy can't seem to keep a solid connection. I try a few songs, one makes it through, then I go back to another and my computer loses connection to my network again.
So point being is it appears to be an iTunes issue and not a Zeppelin issue. In fact this is my second Zeppelin, I returned the first one because it was having the same problems.
The only functional difference I can see is that iTunes seems to be more responsive in the congrols for pause/play/volume where as Airfoil has a slight delay. I feel that maybe iTunes is pushing too much data out for my wireless adapater to handle?
Also streaming Pandora from an ipad works no problem...
I'm going to be trying a new adapter soon, but curious to see if anyone has any insights.
Thanks,
Travis

I've narrowed down the problem to a combination of my Windows Vista 64 machine and streaming directly from iTunes.
I tested my laptop with XP and had no problems streaming from iTunes.
I then connected my Vista machine directly to the router and when streaming directly from iTunes I had all sorts of skips and pauses, but when streaming from Airplay no problem.
I attached an image of my network stats from the same song via iTunes and Airplay. The spikes in the network traffic seem to be the problem when streaming from iTunes...

Is it possible to view photos in icloud from an XP pc without the icloud control panel?

is it possible to view photos in icloud from an XP pc without the icloud control panel?

The iCloud control panel requires Windows Vista or later.
Regards.

Is it possible to export your animated menu from adobe encore into adobe flash with the intention of

Is it possible to export your animated menu from adobe encore into adobe flash with the intention of using that menu for a website or phone app??

encore is used to create dvds. it does export anything that you could load into flash: http://helpx.adobe.com/encore/kb/file-formats-supported-encore-cs5.html

Does everyone on the wireless network have access to the shared files?

I just bought a 1TB time capsule today. I am backing up my files as I type. I also used it to set up a wireless network in my apartment. This wireless network will be used by my roommate as well.
In addiction to backing up my files using Time Machine, I am also going to use my new TC as an external hard drive to store movies, music, photos, and documents. I would like my roommate to have access to the wireless internet, but I do NOT want them to have access to my files.
I noticed that my TC shows up in the SHARED section in my finder. Does this mean that, because my roommates have access to my wireless network, that they have access to my files through the TC shared drive? If so, how can I protect my files?

I found this in the Airport Help. It works with the TC drive and any other drives attached.
To set up a user account:
Open AirPort Utility, located in the Utilities folder in the Applications folder on a computer using Mac OS X, and in Start > All Programs > AirPort on a computer using Windows.
Select the device you’re setting up, and then click Manual Setup. Enter the password if necessary.
Click Disks in the toolbar, and then click File Sharing.
Choose "With accounts" from the Secure Shared Disks pop-up menu, and then click Configure Accounts.
Click Add , enter the user name, and then give the user a password.
Choose Read and Write, Read Only, or Not Allowed from the File Sharing Access pop-up menu, depending the access privileges you want to assign for this user.

Downloadable acls and access to the client

I have some downloadable acls working fine filtering traffic from the client towards the unencrypted connect. I am having problems with getting some traffic working the other way, I just want to allow RDP to the clients.
This is the acl :
permit TCP any any eq 80
permit TCP any any eq 443
... removed for
permit TCP 172.16.0.0 0.0.255.255 172.16.x.0 0.0.0.255 eq 3389
In the last line the 172.16/8 is the source and 172.16.x/24 the destination,
thanks

Andbrowny, Here is my network layout. 10.5.6 14 Clients and 1 server with network account homes. The network is in a Print Factory inside a Federal Prison. We use Adobe CS4, QuarkXpress, and other software. Right now, My Inmates can see the harddrive and I do not want the Inmates see it at all. I just recently setup 2 standalone XP boxes and I can hide C: drive. I thought that was cool so I want the same thing with my Macs.
Thanks, PrepressCOP

SCCM 2012: push client sccm 2007 client worked but then no deployment is reaching the client

Hi,
We upgraded an sccm 2007 client to sccm 2012 and are deploying a tasks sequence to it.
However, the task sequence is not appearing. Also we cannot connect via client center tools.
Sccm 2012 client seemed to have installed correctly.
Please advise what logfiles to check.
J.
Jan Hoedt

Sccm 2012 client seemed to have installed correctly.
"Seemed to install" or did it really install? Nothing has changed logfile-wise from CM07 to CM12: ccmsetup.log can still be used to examine if the client was installed successfully. LocationServices.log, ClientIDManageStartup.log etc for further communication
troubleshooting.
Torsten Meringer | http://www.mssccmfaq.de

Loss of wireless radio control via Fn+F5 - without Access Connections

Hi everyone,
I run Windows XP on my X41. I do not have Access Connections installed, and I do not wish to install it. I have recently updated my wireless drivers, and have since lost the ability to control the power settings via Fn+F5. When I press Fn+F5, the following is displayed:
Change Power Settings of Wireless Radios
Unable to change power state of 802.11 Wireless Radio.
Update the driver for the wireless adapter.
I have removed and re-installed the hotkey, wifi and power management software, to no avail.
Any help would be welcome.
Also, can anyone explain what the different utilities that come with the Intel PROSet achieve? Specifically, WMI support.
Thanks in advance.
X41 1.5GB RAM (Looking for a cheap 1.8" SSD or CF solution)

Hi, in my experience you need the ProSet portion of the Wireless driver installed to activate the Fn+F5 functionality. Installing the ProSet provides the AEGIS protocol for the wireless card.
If you check in the Properties of the Wireless card (through Control Panel>>Network Connections and right click the wireless connection) you should see the AEGIS protocol in the item list of the 'General' tab. If the protocol is not present try running the ProSet install of the wireless driver, and check the protocol is present, and this should fix the problem of Fn+F5.
Hope this helps.

Is it possible to control a Mac directly from an iOS device without being connected to a WiFi network, i.e. an airport or similar.

I would like to control my MacMini (Late 2012) 2.3GHz Intel Quad Core i7 processor directly from my iOS device, either my iPhone 6 or my iPad G3. By directly I mean without having a wireless or wired network in place.
I know there are a number of iOS apps that utilize VNC technology but I believe they all require the Mac to be connected via WiFi to an Airport or similar wireless networking device. I would like to control my MacMini remotely without having it already connected to a WiFi network and wondered is it possible? The iOS device and Mac would be in close proximity to one another.
Has anyone had any experience with this? Thanks.

Guys, thanks but I did not mean to control it by infrared. I know only too well that iOS devices do not have that capability. However they and the Mac both can send and receive WiFi signals so is there any reason they can't talk to each other directly.
When I am in my home I have an airport but I would like to take the Mac Mini out on music gigs with my Apollo interface which serves as my mic preamp and mixer as it does in my studio but the Apollo needs to be connected to the mac via thunderbolt to download the plugin software that provides reverb and eq, etc. I would like to do this without the need of a monitor and keyboard, hence my dilemma. The only thing I basically need to do is start the mini and the rest happens automatically but I need to also shut down (which I know can be accomplished a couple of ways) but with out having a visual interface you can't make any changes or verify what setting are being used.

Hello, I have creative cloud installed on my Mac Book Pro - OS X 10.9. 5 When trying to download trial version, a popup window shows the message " you have been disconnected" Connect to continue. No way to access to the download programs after entering t

Hello, I have creative cloud installed on my Mac Book Pro - OS X 10.9. 5 When trying to download trial programs, a popup window shows the message " you have been disconnected" Connect to continue. The same message comes after repeated attempt to entering the login and password info. How can I solve this?

Hi Jeff,
Here is the screenshot of the window which comes after any attempt to download a trial version. It is in French, it means you have been disconnected, connect to continue.

Wireless LAN Controller not broadcasting network to Access points

Good Day Team,
I am working with a 2100 series WLC controller and 1100 series access point.
I noticed that the wireless lan controller is working. Also the access point is working.
The issue is that there is no internet connection on the access point.
What could be the error?
Kindly advice

Try do diagnose your problem following this steps:
1) Connect to the wireless network
2) Check your IP address with "ifconfig"
3) Check if your gateway is set correctly with "route -n"
4) Try to ping your gateway. Is it working?
5) Try to ping an internet IP like google: "ping 74.125.234.115"
6) Try to resolve names with "nslookup www.google.com" for example.
7) Try to traceroute to an IP or name on internet. Check the result to see the last hop you reached.
8) If you passed all those tests, try this: "telnet www.google.com 80"
If everything works, but not the test #8, your problem could be related to some proxy configuration.

I'm using firefox version 4 in my network and i want the clients can't change my network proxy that we are using i did it in previous version but it doesn't work in version 4, so how can i do it?

I've network in my company and installing internal web proxy that allow clients to connect to the internet (ISA 2004). i'm using the Firefox as default browser in my network. so what i need that no one in my network clients can't change the proxy settings or it just be dimmed. i did it in the previous version but when i try the steps in version 4 it doesn't work so I'm asking for solution for that.
many thanks for help,
Ahmed Khairy

Leliforever, cheek you list of installed add-ons, the Ask toolbar can be installed without the users knowledge.
For checking other extensions that may cause this, follow the procedure in this link - https://support.mozilla.com/kb/Troubleshooting+extensions+and+themes

Can either the Airport Express or Airport Extreme be used "standalone" to create a wireless network with access to the internet?

I want to create a wireless network for my iMac, Macbook Pro and iPad, and I'm confused about the Airport Extreme and Airport Express devices.
There is mention for both about connecting them to a DSL or Modem. Does this mean I have to obtain additional hardware before they will enable connection to the internet? (In the past, I've used a Belkin Router, which simply connected to the phone line.)
Any advice gratefully received.
Tony

Does this mean I have to obtain additional hardware before they will enable connection to the internet?
Yes, you need a modem. The AirPorts are routers only. They do not have a modem built in, so you will need a modem if you want to be able to connect to the Internet.
The Belkin device that you have used before is a modem/router. It combines the functions of a modem and router in one package.

Is it possible to have an iphone without access to the internet?

I would like an iphone but I don't want to have access/pay for the internet all the time. I don't know if it's even possible to but an iphone without it though.

A carrier is not the only place to buy an iPhone. You can buy unlocked, without a SIM, direct from Apple, activate it with a borrowed SIM, then just use it on WIFi.
Might as well just buy an iPod touch though...

'm using firefox version 4 in my network and i want the clients can't change my network proxy that we are using i did it in previous version but it doesn't work in version 4, so how can i do it?

''locking as a duplicate of this thread - https://support.mozilla.com/en-US/questions/827625''
I've network in my company and installing internal web proxy that allow clients to connect to the internet (ISA 2004). I'm using the Firefox as default browser in my network. so what i need that no one in my network clients can't change the proxy settings or it just be dimmed. i did it in the previous version but when i try the steps in version 4 it doesn't work so I'm asking for solution for that.
many thanks for help,
Ahmed Khairy

Leliforever, cheek you list of installed add-ons, the Ask toolbar can be installed without the users knowledge.
For checking other extensions that may cause this, follow the procedure in this link - https://support.mozilla.com/kb/Troubleshooting+extensions+and+themes

Is it possible to to disconnect 2 wireless clients from my wireless network without access to the clients i.e. 2 iPads?

Similar Messages

Maybe you are looking for