Is it possible to turn down the D channel on a Qsig trunk

We're working with a mgcp controlled 3845 and a mgcp controlled 6608 blade in 6509 switch. We're connecting to a Nortel PBX using Qsig trunks.
We're testing failover for calls from the Nortel system over multiple Qsig trunks to the 3845 and the 6608, i.e. if the Nortel see the trunk is down it will hunt to the next trunk.
What the Nortel engineers are requesting us to do is to turn down the D channel on a trunk from the 6608 or the 3845 to the Nortel PBX to see if their equipment will hunt to the next Qsig trunk if it sees the D channel down.
Thanks,
Jim

On the 3845, go to the interface serial and do a shut down to bring down the D channel. For example, if the T1 is connected to port 1/0, then do the following
interface serial 1/0:23
shutdown
On the 6608, if you are connected to port 5/1, then disabling that port will bring down the D channel. Use this command
set port disable 5/1
Regards,
Anup

Similar Messages

  • HT1305 how can i turn down the fan rpm that's between the optical drive and hdd in my power mac g5 dual 2.3?

    how can i turn down the fan rpm that's between the optical drive and hdd in my power mac g5 dual 2.3?

    Ok, I saw that error in your logic. A Dual G5 2.3 or even a Dual Core 2.3 does NOT use LCS at all. Its air cooled and if anything if the OP is experiencing this problems could be due to possible heatsink paste drying up. He might have to re-apply MX 7 or Arctic Silver.
    The only G5's that use LCS are: G5 dual 2.5 from Late 2004, the G5 Dual 2.7 from Early 2005, and lastly the G5 Quad-Core from Late 2005-end of September 2006.
    Hope this helps.

  • Camileo S20 - Is it possible to turn off the screen?

    Is it possible to turn off the screen when using Time Lapse or Motion Detection modes so as to save power?

    Hi buddy,
    I have downloaded the user manual off Camileo S20 and searched a little bit but unfortunately I can find no informations about turning off the screen when using Time Lapse or Motion Detection. It seems that the screen is always on.
    But you can connect the AC adaptor while recording movies. So you have always power. :)

  • Turn down the volume of built-in speaker before playing music

    So I was wondering if there was any way to turn down the volume of the built in speaker prior to playing music/video. I imagine that if I'm REALLY quick and pause the action, I can turn it down, but I'd rather not have to race against time.
    The context for this, is the desire to show someone else video on the iPhone (say a National Geographic video podcast) without the audio blasting forth.
    Any ideas?

    So you're saying the phone doesn't remember the previous setting you had it at and jumps up or something...?
    ..or you want to hit play and have it not play so you can adjust the volume first...sorry can't help if that's the case. It kind of doesn't make sense from a UI perspective, when I press play or start a video I want it to play....different strokes for different folks tho

  • How do i stop muting people during my conversations? i don't mean to hit mute but it always happens. can i turn down the sensitivity?

    how do i stop muting people during my conversations? i don't mean to hit mute but it always happens. can i turn down the sensitivity?

    The iPhone includes a proximity sensor which puts the screen to sleep or turns it off when the iPhone is held to your ear and face during a call.
    Do you have a screen protector installed and/or are you using a case that might be blocking or partially blocking the proximity sensor?
    If you are using a case, remove the case before the next call. If the same does not occur without the case, you need to get another case that doesn't block the proximity sensor.

  • I have a problem choosing artist from my artist list when I will put music on my iPad from my iMac. I can only see the 25 first artis and it is not possible to scroll down the list

    have a problem choosing artist from my artist list when I will put music on my iPad from my iMac. I can only see the 25 first artis and it is not possible to scroll down the list

    Hi stig68,
    If you are having grouping issues with compilation albums in iTunes, you may find the following article helpful:
    Apple Support: Why aren't songs with the same album art grouped together?
    http://support.apple.com/kb/TS1468
    Regards,
    - Brenden

  • Is it possible to turn off the Apple dock completely?

    I was wondering if it was possible to turn off the Apple dock completely without causing irreparable damage to my system. I am considering using Drag Thing, but when I am using it the functionality seems redundant with the Apple dock, also using both programs in tandem uses up more precious memory. The Drag Thing website links to the following tutorial as a solution:
    http://www.creativemac.com/2003/02_feb/tutorials/dockdead2030225.htm
    But it was published a long time ago, and I don't want to do anything rash that would damage my system, I mean I don't dislike the Apple dock enough to do that. Thanks in advance for the consideration and suggestions.

    I could only discover an option to hide the dock from within Drag Thing. I am looking to make the dock disappear completely. Drag Thing does not officially support this option, giving this answer in the Q & A section of their website:
    "*It is possible, but I wouldn't recommend it. Since people often ask how to do it anyway, here's a good tutorial I found on how to kill the Dock by Kevin Schmitt. This may have unforseen side effects however, which is why I've not documented the procedure myself, or added an option for this in DragThing. I keep the Dock hidden off the bottom of the screen on my own Mac.*"
    Is the dock so embedded within the Finder's operations that killing it will affect system performance?

  • Is it possible to turn off the passcode?

    I’ve seen a couple postings that say go to Settings --> General --> Passcode Lock, but on my iPhone 4s I don’t see anywhere to turn it off at that point.  In the manual, there is no description of turning off the passcode – at least I didn’t find it.
    Is it possible to turn off the passcode?

    row6 wrote:
    no, once you get to Passcode Lock, there is no option to turn it off - certainly none visible to me.  Have you actually tried to do this?  Do you have an iphone 4s?
    Here is a screen shot of what you get when you press "Passcode Lock".
    You have to ENTER your passcode first, to access the part of the Settings that allows you to disable the passcode lock.
    Enter your passcode.
    Then you can turn the passcode off.

  • Is it possible to turn off the updates that make your iphone need to be activated again?

    Is it possible to turn off the updates that make your iphone need to be activated again? Because you need wifi in order to activate and sometimes I don't have wifi so my iphone becomes unusable untill I get wifi again.

    I'm sorry but it says 8.1.2 on my phone when I check for the info about the software.
    The issue I have is that on random moments it asks me to activate my phone ( I think after an update or some kind ) but sometimes I have no access to wifi to activate it so I was wondering if I could make that stop?
    I'm sorry for the strange explanation, english isn't my mothertongue

  • Is it possible to turn off the fluid grid function in dreamweaver during the process of building your site by mistake? It was working fine and simply stopped and I don't see how to correct what is wrong.

    Is it possible to turn off the fluid grid function in dreamweaver during the process of building your site by mistake? It was working fine and simply stopped and I don't see how to correct what is wrong.

    There is no specific function that turns FGL on or off.
    When you say that it has stopped, do you mean that the handles no longer show?
    If that is the case, then I think you may have modified the CSS to such an extent that Dreamweaver no longer recognises it as belonging to FGL.
    There are a couple of avenues for you
    Redo the site and make sure not to touch the FGL CSS
    paste the code here so that we can see what has gone wrong.

  • Turning down the verbosity of logging in  search service

    Hello old friends.
    Our search node is generating 1.5gb of logs per day. how can i turn down the verbosity of the logging? I don't see any configuration files that get read, and the config mgr doesn't have anything about logging verbosity.

    Here are 2 log file settings in the search area, not sure what they impact but I don't see many other log setting files.
    Definitely let us know what you uncover though.
    1)
    Cluster.ini file at this path:
    \bea\alui\ptsearchserver\10.3.0\cluster
    # Logging
    # The following settings may be used to override the default logging policies.
    # For a given severity level specify a comma-delimited list of values
    # corresponding to the logs which should receive log messages at that
    # severity level. Acceptable values are trace,event,cluster,none.
    # Note that internally log messages are routed either to the cluster log
    # or the local logs. While a cluster log message may be echoed to the
    # local logs, a local log will never be sent to the cluster log
    #RF_LOG_DEBUG_OUTPUT=none
    #RF_LOG_INFO_OUTPUT=trace
    #RF_LOG_WARN_OUTPUT=trace,event,cluster
    #RF_LOG_ERROR_OUTPUT=trace,event,cluster
    #RF_LOG_FATAL_OUTPUT=trace,event,cluster
    #RF_LOG_PERF_OUTPUT=none
    #RF_LOG_FUNC_OUTPUT=none
    #RF_LOG_ACTN_OUTPUT=none
    2)
    wrapper.conf file at this path:
    \bea\alui\ptsearchserver\10.3.0\adminui\settings\config
    # Service wrapper Logging Properties
    # Logging properties for the service wrapper only, these properties
    # do not control application-specific logging.
    # Valid log levels for console, log file, and sys/event log output are
    # DEBUG          Verbose debug messages
    # INFO          JVM output and informative messages.
    # STATUS     State changes
    # ERROR          Errors only
    # FATAL          Fatal errors only
    # Format of output for the console. (See docs for formats)
    wrapper.console.format=PM
    # Log Level for console output. (See above for log levels)
    wrapper.console.loglevel=INFO
    # Log file to use for wrapper output logging.
    wrapper.logfile=%APPLICATION_PATH%/logs/wrapper.log
    # Format of output for the log file. (See docs for formats)
    wrapper.logfile.format=LPTM
    # Log Level for log file output. (See above for log levels)
    wrapper.logfile.loglevel=INFO
    # Maximum size that the log file will be allowed to grow to before
    # the log is rolled. Size is specified in bytes. The default value
    # of 0, disables log rolling. May abbreviate with the 'k' (kb) or
    # 'm' (mb) suffix. For example: 10m = 10 megabytes.
    wrapper.logfile.maxsize=0
    # Maximum number of rolled log files which will be allowed before old
    # files are deleted. The default value of 0 implies no limit.
    wrapper.logfile.maxfiles=0
    # Log Level for sys/event log output. (See above for log levels)
    wrapper.syslog.loglevel=STATUS

  • How do I turn down the volume of the Media Browser in Audition?

    See subject above/

    I'm using an RME Multiface II and mixing in 5.1, but the point is that the project is very quiet, and many of my samples are loud. If I turn down the whole thing, I can't hear the soft project over the loud samples that I'm trying to add. (When I'm working in Acid or Reaper with loop-based stuff, I can simply turn down a volume slider in the media browser equivalent.)
    -SCP

  • Is it possible to turn off the sound and just vibrate for incoming email?

    Is it possible to turn off the sound on my Verizon iPhone 4 and just have it vibrate for incoming email. Can't seem to find any way to do this!

    You could either flip the mute switch or go to Settings > Sounds > New Mail = Off

  • Is it safe to turn down the fanspeed on my nx6800?

    Hi,
    I just bought a new case that's really silent, and now the sound of the VGA cooler on my MSI NX6800-TD128 (non-ultra, just plain geforce 6800) really stands out. I would like to turn it down (it's on max now, as per default) but how low can I turn it and still be able to, say, play doom 3 without my card getting too hot? I haven't overclocked it, and I have the copper cooler. The ambient temperature in my case is about 28C if the motherboard is to be trusted. Does the card have a thermal sensor somewhere, and if it does, how high can I allow the temperature to go?
    I read somewhere that it would even be safe to turn down the fan to minimum (http://www.digit-life.com/articles2/gffx/nv40-5.html), but I figured I'd ask here first.
    Thanks!

    28C is a comperetivly low case temperture.
    You sould be able to reduce it a bit, say 30%. If it does run too hot you will notice so called artifacts.
    Just raise the fan speed after that happens.
    If u want to make it really silent, get one of these:
    http://www.arctic-cooling.com/vga2.php?idx=40

  • Inspire s2 wireless turns down the volume by itself.

    Hey. I bought my Inspire about a year ago and it worked fine.
    Then suddenly when i connected it to my laptop it turns the volume down. I can turn it up again but it just keeps muting.
    First i thought it was my laptop settings and i'm not a geniuos with computers.
    But then i connected the speakers with my iPod touch and it still turns down the volume totally random. It does it approx every 5 minutes.
    Can anyone tell what the devil the matter is?
    (Sorry for my english, i'm danish :P )?

    Hi,
    Sorry but this doesn't sound right, I suppose something's wrong with the speakers. You might want to contact Customer Support for assistance.

Maybe you are looking for