Is my PowerMac G4 done for?

I am trying to do a complete erase/re-install of Tiger on my Power Mac G4 as my computer stopped booting up. I started up the computer booting of the install disk and ran various disk utility tasks but I have not been able to re-install the operating system on the machine. Sometimes when I boot from the disk the harddrive is nowhere to be seen.
Is my machine done for?

Unfortunately there is no uniformity in jumper settings. Typically there is a diagram somewhere on the drive that shows how the jumpers have to be set. Here's an example:
http://eshop.macsales.com/Tech/manuals/idehdsettings/WD72.pdf
You are looking for a set of pins - five or six pairs of them - that are on the edge of the drive, often between the power connector and the ribbon connector. There is a black "jumper" that is installed to straddle a pair of pins. You can just lift that jumper off with a long nosed plier, or even your finger nails, and reinsert it where it belongs. A trial and error approach with the jumper cannot harm the drive.
Here are a couple of links to diagrams for jumpers, but as I already said, there is no uniformity among drive manufacturers, or even drive models from the same manufacturer.
http://www.seagate.com/staticfiles/images/support/en/us/mxoata_jumpersrev.jpg
http://rtvpatch.sourceforge.net/jumpers.html

Similar Messages

  • Depot Sales - Goods issue not done for the delivery

    Hello Experts,
    I am trying to capture a Excise Invoice in the Depot Sales Process TCode - J1IJ.
    I am getting the follwoing message - GI not done for the Delivery.
    Process which we are following here is
    Depot
    SO - Delivery - Picking - Packing - J1IJ - Shipment creation - Shipment Planning - Loading Start - Shipment Start (Will do PGI) - Shipment end (Will create invoice & Excise Invoice).
    Excise invoice is captured during MIGO at Depot.
    Can you please suggest..
    Thanks & regards
    Mahesh

    Hi mahesh
    Change the process to following manner
    Depot
    SO - Delivery - Picking - Packing - Shipment creation - Shipment Planning - Loading Start - Shipment Start (Will do PGI) - Shipment end -J1IJ(Will create invoice & Excise Invoice).
    u r problem will be solved.
    Regards
    kedasu.a

  • How many implimentations can be done for a single BADI definition?

    How many implimentations can be done for a single BADI definition?
    Is there any restriction to impliment a single BADI definition?
    Plz answer with proper explanation....
    Thank you in advance
    REgards,
    Chaitanya

    hi Krishna Chaitanya,
    In a badi if the "Multiple Use" Checkbox is checked then You can have any number of Implementations for the BADI
    Say I have defined a BADI "BADI1"
    and I have 3 implementations
    IMP1
    IMP2
    IMP3
    The order of execution will be IMP1, IMP2 and IMP3
    In a badi if the  "Multiple Use" Checkbox is not checked then You can have ONLY ONE  Implementation for the BADI
    Say I have defined a BADI "BADI1"
    and I have 3 implementations
    IMP1
    IMP2
    IMP3
    Only one Implementation can be active at a time and only that will get executed
    Hope this helps a bit
    Reward if Useful
    Cheers
    Kripa Rangachari.

  • Error "Part1 will not be done for the excess GR quantity" in STO GRN

    Hi,
    While posting STO grn the error message is displayed "Part1 will not be done for the excess GR quantity".
    We have checked CIN settings for Excise groups, the "GRs per EI" is maintained as "2 Multiple goods receipt, multiple credit".
    In J1ID, for materials it is already maintained as "2 Multiple goods receipt, multiple credit".
    No partial GR is posted for the delivery.
    Still system is throwing the error message "Part1 will not be done for the excess GR quantity".

    Hi,
    Please provide the following for a clear picture.
    1. PO qty
    2. Quantity invoiced by the supplying plant
    3. Quantity you are mentioning in GR
    Regards,
    Siva

  • I have Photoshop CS5, and use windows XP.  I cannot open Bridge from photoshop, whichI have done for years. When I am in Photoshop,when it opens, I always click on the bridge icon at the bottom of the screen, and it puts me into bridge. This is not happen

    I have Photoshop CS5, and use windows XP. I cannot open bridge from photoshop, which I have done for years.  When I am in Photoshop, when it opens, I always click on the bridge icon at the bottom of the screen and it puts me into bridge. This is not happening, the small wheel at the bottom of the screen just keeps spinning. Its like its stuck or caught in a loop. I can't get into bridge. I tried shutting down and starting up again but  the problem remains. Looking for help.  Dan

    Thanks for your response, I was able to open bridge from File-Browse in Bridge.  This worked, but was not able to go back to the way I always opened Bridge.  At least I could get to Bridge and go into Camera Raw. I never tried to open Bridge from the Start menu.  The odd thing about this is, it has happened before, and to get it "unstuck" and working again, I would shut down and restart again in a few minutes, and things would go back to normal.  This time it did not go back to normal after several attempts.  I shut down for about 3-4 hours, restarted, and it seems to be back to normal again. I am not sure if it's a problem that is getting worse each time it happens.       And yes I am using Mini Bridge in photoshop CS5.  Thank you for your help.  Dan

  • Third party items are not invoiced totally though the MIRO done for all

    Hi Gurus,
    I have a third party sales order with 3 item lines.
    All these three items are delivered to the customer by the vendor and invoice verification MIRO also done for all three.
    Now when the order related invoice creation background job run and invoice created for this order is missing the first line item in the invoice. I cant understand what is the problem with first item line? Order is now not in the invoice due list also. manually invoice creation also gives the log that the order is completely invoiced. But when we see the document flow for item line 1 it says the item line is yet open and not invoiced.
    suggest me as the invoice posting is required for this item line also. suggest all the possible reasons.
    regards,
    Sandesh

    Hi Navneetha,
    Thanks for d reply.
    I hv checked d mentioned tables and Itm Categories nothing is +ve there. All 3 itms hv TAS itm category. Also I agree with ur MIRO statement.
    I found one thing which might b d cause plz check.
    As we knw dat we cant change the schedule ln date and quantity once the Pur. Requisition created. and we cant make changes in sales order itm line if the PO is created for that Pur. Requisition. Bcoz afteward the PO wont be updating  the Pur Requsition and sales order automatically.
    But here the schedule line date at d schedl ln category for itm 2 is changed by a certain Batch job after the PO cration.
    Therefore I think this wd b d reason that the item line 2nd is not getting updated in sales order from the PO and looks open.
    The change of schedule line dates is not maintained in the PO manually ever.
    So would it b d reason for the inconsistent doc flow updates and 2nd item being open as not invoiced yet?
    regards,
    Sandesh

  • Standard Report for GR done for Purchase requisition

    Hi all,
    Is there any standard report from which i can get Goods receipt done for Purchase requsition.
    I can get the details from ME80FN
    Through dynamic selection.
    Anybody is having any other solution apart from this.....
    Regards
    shailesh

    Thanks a Lot both of you for the quick response.
    Actually the requirement of the client is such that , The requester should either recieve mail notification that GR has been done for a PArticluar PR.
    Or whether there is any report which can result into GR done for Pur Req created.
    If there is no standard report ........Can the notification be sent to Requester whenever GRN for Preq is done
    The requester is moreover interested in Knowing about the status of the PR Created by him whether GRN has been done or not.
    jeyakanthan>>>I havent tested this ME80RN report suggested by you ,might be i will have alook at it tomorrow.
    Regards
    shailesh

  • Find payment done for vendor - PO?

    Hi experts
    How to find payment has been done for this vendor for particular PO from Fi side .
    Not invoice receipt only, but totasl payment ..
    Thnaks

    1.  Call up the PO in ME23N.
    2.  Click on Purchase Order History tab in item details.
    3.  If invoice is already posted, double-click the IR number.
    4.  Through "Follow-on Documents" show Accounting Document.
    5.  In the accounting document, double-click the vendor master number.
    6.  The check information is displayed.  The "Clearing" field in Additional data will show the date the payment was made.
    There may be some authorization issues to resolve depending on the access of the users that need to view this data.
    Another way would be to view the clearing date would be to display the BSEG table in SE16/SE16N if you can run these transactions.
    Hope this helps.

  • Using Overdrive to download WP3 audiobook, then wanted to transfer to itunes (as I have done for years) and couldn't find portable player.  Don't want it to go to portable player, want it to go to itunes/music. Can I change "player"?

    Using Overdrive to download WP3 audiobook, then wanted to transfer to itunes (as I have done for years) and Overdrive couldn't find portable player.  Don't want it to go to portable player, want it to go to itunes/music. Can I change "player"?  When I "transferred" to iPod, I couldn't find the book.  Have updated iTunes and Overdrive.

    Sorry, I can only advice that you go to ubuntu ipod forum, for a better response.
    Here I can suggest install iTunes and Restore the iPod.

  • Not used my G5 Powermac (late 2004) for ages. Only boots in with Installation disk, but colour dots on white screen and message comes up to reboot machine. Nothing happens.

    Not used my G5 Powermac (late 2004) for  about 2 years. Was going to set it up for the lads to do school work.
    However it only boots in with Installation disk, but colour dots on white screen and message comes up to reboot machine. However nothing happens apart from me keep trying. Also the numerous fans get louder and louder and louder.....
    Any ideas folks

    Can you please provide details on the exact model?
    For a start, the PRAM battery is likely dead.  PRAM tells the computer which drive to start with, other basic information.  Still, you can usually get the computer to start, though bad PRAM is unpredictable and could be stopping that.
    Some computer models use software to control cooling fans.  If there's no software commands they automatically go into high speed to prevent overheating.  Your software obviously isn't loading, so runaway fans.

  • How to know  Whether Partition is done for Cube or not

    Hi All,
    I need information regarding Partition of a cube.
    a)How do i know the Partition is done or not for Cube
    b)On what basis we should make parttion of Cube.
    Thanks and Regards,
    C.V.

    There are several threads on partitioning, so it would be a good start for this question (as with any question) to search the BI forums on "Partitioning" and review thsoe first.
    Some basic considerations on partitioning -
    - Your DB must support Range partitioning to permit partitioning your InfoCube. The option will be greyed out if it is not available.
    - InfoCube must be empty to be partitioned.
    - InfoCube can only be partitioned on 0FISCPER or 0CALMONTH.  You can define it so that you have a partition for each month/fiscper, or so that each partition will hold a few or several months of data.
    - Generally, you would not partition small cubes.
    - Thru BW 3.5 Aggregates automatically get partitioned the sme way the InfoCube is partitioned as long as the partitioning characteristic is in the aggregate.  In 2004s, I believe you have options as to whether an aggregate gets partitioned or not.
    - Partitioning may be done for query performance reasons and data administration.  If the queries on the InfoCube regularly run with restrictions/filters on the partitioning characteristic (FISCPER or CALMONTH), the database will "prune" any partitions that do not contain the FISCPER/CALMONTH value(s), so that it does not need to consider them , e.g. most of your users only run a sales query for the current and previous month, but your cube contains 3 years of data.  By partitioning on CALMONTH (we'll assume 1 partition / month), the database will exclude all but the two partitions from consideration.  This could help query performance a lot. or maybe only a little, depending on a variety of other factors.
    Again - it is important that the queries restrict onthe partitioning characteristic to be of any value on query performance.  So don't partition on FISCPER if all the queries use CALMONTH for restrictions.
    The data adminsitration reason you might partition is to improve selective deletion or archiving time.  These processes are capable of using a DB function to Drop the partition, which quickly removes the data from the cube, rather than having to run a resource intensive Delete query.  This only happens if you deletion/archiving criteria is set to remove an entire partition of data.
    Again - review the other threads on the BI forums on Partitioning.  Most questions you have will already have been asked and answered before, and post again on SDN if there is something you still have a question about.

  • HT4623 what can be done for the ipad that is making people dizzy and having headaches?

    what can be done for the ipad that is making people dizzy and having headaches?

    Go to settings>general>accessibility>reduce motion> turn on.

  • Changes done for sap user details

    Hi All,
    I need to know a standard transaction code or FM;
    which can give the information on the modifications/changes done
    for the sap user's first name; last name and e-mail id.
    Any help will be appreciated.
    Thanking you all in advance.

    Hi Kanagaraja,
    I really appreciate you inputs, it will definitely have entries posted by BAPI.
    But the requirement I have is little different.
    I will have some person changing the user information manually,
    I need to go somewhere and find out whether the person has made the
    changes in user's first name, last name or e-mail id.
    So, I am looking out for some FM or table or even standard t-code where
    I could find the changes done, and change log lately.
    Thanks and Best Regards

  • How is Output determination done for a PO ??

    Hi
    How is Output determination done for a PO ??
    I need the O/P to the vendor sent in the form of a PDF file.
    is it possible !!
    cheers
    Maruthi

    Hi,
    1. Condition Table
    SPRO > Material Management> Purchasing -> Message -> Output Control->Condition Tables->Define Condition Table for Purchase Order
    Select: 
    Purchasing Doc. Type,
    Purch. Organization,
    Vendor
    2. Access Sequences
    SPRO -> Material Management-> Purchasing -> Message -> Output Control->Access Sequences->Define Condition Table for Purchase Order
    3. Message Type
    SPRO -> Material Management-> Purchasing -> Message -> Output Control->Message Types->Define Message Type for Purchase Order
    *4. Message Determination Schemas*
    4.1. Message Determination Schemas
    SPRO -> Material Management-> Purchasing -> Message -> Output Control->Message Schema->Define Message Schema for Purchase Order-> Maintain Message Determination Schema
    4.2. Assign Schema to Purchase Order
    SPRO -> Material Management-> Purchasing -> Message -> Output Control->Message Schema->Define Message Schema for Purchase Order-> Assign Schema to Purchase Order
    5. Partner Roles per Message Type
    SPRO -> Material Management-> Purchasing -> Message -> Output Control-> Partner Roles per Message Type ->Define Partner Role for Purchase Order
    6. Condition Record
    Navigation Path: SAP Menu-> Logistics -> Material Management -> Purchasing-> Master data->Messages-> Purchase Order-> MN04-> Create
    Now you create PO (ME21N) and save it. Go to ME22N and print the PO by giving output type.
    Output of GR
    After setting table, access sequence and output type for GR,run MB02 transaction, enter material document number. Double click one line item and select messages. Separate screen will be opened to configure outputs. Give the required fields and save the document. 
    Now Run MB90, you can take printout. Output Type: WE03 or WE01 or WE02
    Thanks,

  • Display changes done for reservation

    Hi Guys
    I have client requirement as below
    They  need to view changes done for reservation
    Can any boy help on this
    Thanks in Advance
    SAP MM

    Dear,
    We have this requirement and we raised OSS to SAP also on this.
    Reservation changes cannot be tracked in SAP system due to least importance it has. One work around through ABAP development but its not supported by SAP due to abnormal increase in data volume of change recording in data base which impacts system performance.
    For this we, go with authorization matrix by which remove MB22 authorizations from all users and make one super user like concept. Means one plant only one user has authorizations for MB22 for which he can change the reservation. He get instructions whenever any user want to change reservation - must shoot a mail to all concerning inventory team before he changing with MB22.
    Regards,
    Syed Hussain.

Maybe you are looking for