Is possible to connect PCI by USB3.0?

Hi,
I try to mail this question in the hope that someone can give support to me.
It is possible to connect, by the adapter in the link ( http://it.aliexpress.com/item/PCIe-to-PCI-dual-slot-adapter-card-PCI-express/558 769291.html ), a usb3.0 with a Pci?
So as to make it to work with Win installed on MAC PRO (with Bootcamp).
Thanks!

I don't think it would work, because you need specifics drivers for the usb 3.0 and pci-e is so different than pci (more power and data bandwith), so if you have a free pci-e slot save a bit for the Caldigit card

Similar Messages

  • Is it be possible to connect...

    Is it be possible to connect:
    VGA
    VGA
    VGA or  DVI
    VGA or DVI or HDMI
    USB X9
    Headphones
    To a current MacBook Pro all at once
    thanks

    You don't specify what video card you have but given any mac pro with a single video card the answer to your specific question, i.e., 4 video connections (I'll ignore the USB X9 because I don't know what that is), the answer is NO.
    The current crop of video cards for Mac Pro's have 3 video connections.  So you would need at least two cards for 4 video connections.
    If the USB X9 is a some kind of video then I don't know how you would connect that.  Without some kind of specific pci video card there is no way to get video out of a USB connection that I know of for a mac.
    Update:
    Aaaarrrrggghhhhh!  I answered the above because this was a post in the Mac Pro section and I was talking about Mac Pro's.  Rereading the OP it's asking about a macbook pro.  For that the answer is simple --- NO.

  • Can i connect pci-7344 to my third party motor and drive without umi-7764 ?

    Our Lab have NI pci-7344 motion controller and third party motor and drive made by other company.
    We want to connect pci-7344 and third party motor & drive without umi-7764.
    Just use cable.
    Can we succeed to connect them ?

    In general it is possible to connect the PCI-7344 to a motor drive without using a UMI-7764 but you will loose some safety features and the level of noise immunity for encoder signals will be decreased.
    Please have a look at this link for more information.
    Best regards,
    Jochen Klier
    National Instruments Germany
    Message Edited by Jochen on 01-05-2007 10:19 AM

  • Is it possible to connect an external USB 2.0 hard drive to a Thunderbolt Display?

    Hello,
    Is it possible to connect an external USB 2.0 hard drive to a Thunderbolt Display and back up a MacBook Air to the external hard drive using Time Machine?
    I intend to connect my MacBook Air to the Thunderbolt Display using a Thunderbolt cable.
    I would also like to connect my printer via USB 2.0 to the Thunderbolt Display. Will this also work?
    Effectively using the Thunderbolt Display as a USB hub or docking station.
    Regards,
    Ben

    Ok, thanks.
    My 1 cable to ThunderBolt Display objective
    MacBook Air -> (via 1 x Thunderbolt cable) -> Thunderbolt Display -> (via 1 x USB cable) -> USB 2.0 external hard drive
    I would like to know if this configuration is possible and Time Machine will run correctly.
    Your 2 cable suggestion (I think)
    MacBook Air -> (via 1 x Thunderbolt cable + 1 x USB cable) -> Thunderbolt Display + USB 2.0 external hard drive
    This configuration requires 2 cables to disconnect/reconnect from my MacBook Air.

  • Is this possible: SNC connection from SAP GUI to SAP Router, and ...

    Hi,
    I have (stupid perhaps) question.
    Is this scenario possible:
    SNC connection from SAP GUI to SAP Router, and non-SNC connection from SAP Router to SAP System.
    I know how to set up scenario like this:
    SAP System --- (non-SNC conn) --- saprouter1 --- (SNC conn) --- saprouter2 --- (non-SNC conn) --- SAP GUI.
    Best regards,
    Marek Majchrowski

    Wolfgang,
    To be sure myself and Marek understand, can you confirm the different scenarios supported:
    Scenario 1:
    SAP GUI --- (non SNC conn) --- saprouter1 --- (SNC conn) --- saprouter2 --- (non-SNC conn) --- SAP System
    With this scenario, it would be possible for a user to logon using SAP GUI onto the SAP System, but without SAP GUI SNC.
    Scenario 2:
    SAP GUI --- (SNC conn) --- saprouter1 --- (non SNC conn) --- saprouter2 --- (SNC conn) --- SAP System
    With this scenario it would be possible to logon to the SAP System using SAP GUI, and using SNC authentication.
    Also, with this scenario the SAP GUI software and SAP System software would consider this to be similar to:
    SAP GUI -- (SNC conn) -- SAP System
    Scenario 3:
    This is the scenario mentioned by Marek in his initial question:
    SAP GUI -- (SNC conn) -- saprouter1 -- (non SNC conn) -- SAP System
    With this scenario it will not be possible to logon to SAP System using SNC, and only possible if the SAP GUI is configured to not use SNC. In other words the SNC connection between SAP GUI and saprouter1 is available, but cannot be used.
    Thanks,
    Tim
    Edited by: Tim Alsop on Feb 25, 2008 5:24 PM

  • Is it possible to connect my mid 2010 Macbook Pro with my 21.5" iMac 11,2 so that I can work with dual screens?

    Is it possible to connect my mid 2010 Macbook Pro with my 21.5" iMac 11,2 so that I can work with dual screens?

    try xxx - may work
    _may_ work.

  • Business Contact Manager 2010 - is it possible to connect a Contact with multiple Accounts

    Hi, I'm proficient with Outlook but new to BCM. Currently setting things up but have some Contacts who own more than one company or are on another companies Board etc.  
    My questions is - Is it possible to connect a Contact to more than one Account?
    Many thanks

    Hi,
    Currently it's not possible. The workaround may be to duplicate the contact in Business Contacts to make that happen.
    Regards,
    Melon Chen
    TechNet Community Support

  • My TV is mounted on a wall so I can't connect the Apple TV device. Is it possible to connect to an HD Cable Box and send signal to TV that way? Other problem is that Box only has one HDMI socket .. Help!

    My TV is mounted on a wall so I can't connect the Apple TV device. Is it possible to connect to an HD Cable Box and send signal to TV that way? Other problem is that Box only has one HDMI socket so would also have to use a splitter. Tried Apple Support but couldn't offer a solution. I can't be the only person with this issue surely?
    Help!

    No, unless you are using a home theatre system already, your only option is to connect to the TV.

  • My Apple Macbook Pro is connected by Telstra wireless Broadband to the Internet. Is it possible to connect to a WiFi Printer using Air Express or some other system? to the Internet.

    Hi
    Can someone please advise if it is possible to connect my Apple MacBook Pro 13.3" to a WiFi Printer, as I am connected to the Internet through Telstra Wireless broadband.
    Is it possible by using Airport Express or some other way?
    Thanks

    1.Power Cycle
       Power off the router. Unplug it from the wall. Wait a while.
       Plug it back to the wall. Power the router on. Wait until all the lights are lit properly.
       It will take a while.
      Restart the computer.
      Start up in Safe Mode.
       http://support.apple.com/kb/PH11212?viewlocale=en_US
    2.  Turn off Extensions, if any.
         Safari > Preferences > Extensions
    3. Turn off proxies, if selected.
         System Preference > Network > Advanced  > Proxies Tab
         Under "Select Protocol", uncheck any box if selected.
         Click "OK" then  "Apply"
    4. Uninstall anti-virus software, if any.
    A new Mac comes with 90 days of free tech support from AppleCare.
    AppleCare: 1-800-275-2273

  • Is it possible to connect R/3 4.7 (a.k.a Enterprise) and BI7.0/SEM-BCS6.0?

    Hi,
    Does anyone have some experience or knowledge on this question;
    is it possible to connect R/3 4.7 (a.k.a Enterprise) and BI7.0/SEM-BCS6.0?
    If yes, what is required for R/3 insatallation?
    For example, SP updating on PI_BASIS, SAP-BW or so.
    regards,
    Katsumi

    Hi, greg
    Thanks for your experiential reply.
    > it's a pain to rerun iterations with such an interface, though.
    I want to know some more, if it colud be.
    And, I'm still afraid of interactivity between R/3 4.7 and SEM-BCS 6.0.
    Is there anything required for R/3 insatallation?
    regards,
    Katsumi

  • Is it really possible to connect a iPod Nano to a itrip etc?

    I heard that it is possible to connect the nano to the iRiver aft-100 fm transmitter.
    I this true?
    have somebody tried it?
    if it works just fine, i will buy one!

    Any FM tranmitter will work with the nano as long as it doesn't require the headphone remote port which the nano doesn't have. The iTrip requires this port.

  • Is it possible to connect the iPad to an Infocus and a remote for ppt presentations at the same time?

    I've always used PC and I'm planning on making the transition to Mac.  That's why I'm considering buying an iPad. Today I went to Best Buys and the Mac guy told me that it isn't possible to connect the iPad to an Infocus and a remote for ppt presentations at the same time. Is that true?  I'm a speaker and that was the main reason I was considering buying an iPad, so I didn't have to carry my laptop. Thanks for your help!

    Thanks for your reply. Looks like it can as I have just found this https://www.youtube.com/watch?v=nKp02y4JXVs

  • Is it possible to connect a mac book pro via thunderbolt and a dvi switchbox (multiple computers) to a thunderbolt display?

    Hi,
    I'm planning to buy a thunderbolt display.Since I have not only apple computers with a thunderbolt port I wonder if it's possible to connect my mac book pro via thunderbolt and a DVI switchbox via a "mini displayport to DVI connector" to the thunderbolt display at the same time. Thunderbolt is a bus architecture. Thus there must be an ingoing and an outgoing port on the display. The rearview of the display I've seen so far don't show this:
    If this is not possible then I must question the market chances of this product. Seems as if the product marketing guys exaggerated the launch of the thunderbolt technology.
    -ais-swiss

    ais-swiss wrote:
    How to connect windows laptop (vga) to thunderbolt display?
    AHHH??!!!!!!  Was that your original question??   I assumed you were trying to output FROM your computer (MacBook Pro w/ Thunderbolt) to the new display and then OUT to be the video source to a DVI switcher.
    MB Pro w/TB ---> TB Display ---> mDP-to-DVI adapter ---> DVI switcher
    So it seems as if it's not possible to use the thunderbolt display with the mini display port adapter to DVI you've mentioned.
    I did not understand that you were trying to use other PC's into a switcher and then THAT Video source to connect INTO the TB display.   If THAT is what you're trying to do, then NO....  You can NOT use the new TB Display to be used to display "FROM" a DVI switcher (and also can NOT be used to display from other Non-TB-Apple computers).
    I've also called apple. The statement was that one needs a computer with osx 10.6.x in order to connect the thunderbolt display. That makes it impossible to hook a windows pc or older mac to the new and shiny thunderbolt display.
    I wonder why apple doesn't state this in their technical descriptions...?
    -ais-swiss
    Actually, the state that information all over the Tech Specs on the Apple Store website.
    http://store.apple.com/us/product/MC914LL/A?mco=MTY3ODQ5OTY
    Here are two different statements from that webpage:
    So yes.... other NON-Apple PC's (or non-TB devices) do Not have the Thunderbolt technology (hardware/software) to be able to communicate with the TB display or other TB devices.

  • Is it possible to connect an HP LaserJet P4015n printer to a computer via the ethernet ports?

    My usb port on my Laserjet P4015n no longer works and I am unable to connect this printer to my network router because it's in a different room. Is it possible to connect an HP LaserJet P4015n printer to a computer via the ethernet ports? Of so, how would I go about making this connection? Will I need to install ethernet drivers for this to work?
    Thanks,
    Greg

    This seems to be a commercial product. For the best chance at finding a solution I would suggest posting in the forum for HP Business Support!
    You can find the Commercial Laserjet board here:
    http://h30499.www3.hp.com/t5/Printers-LaserJet/bd-p/bsc-413
    Best of Luck!
    You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

  • Is it possible to connect 2 Samsung monitors to an imac 27"

    Is it possible to connect 2 Samsung monitors with a resolution of 1920x1080 to a new imac 27" with two thunderbolt connectors (per mini displayport to dvi or mdp to hdmi cable)? So that there is the full resolution on all three (Mac + two Samsung) monitors? And if its possible what do I need to do so?
    Thanks for the help

    I have no ThunderBolt iMac (mine is a 2009) nor one or two of these Samsung Displays.
    So I can't say or guarantee that the combination will work.
    Some displays simply don't work with Macs for no apparent reason.
    Best would be to take your MacBook Pro into the store where you want to buy the Samsung displays and ask for a test.
    Stefan

Maybe you are looking for

  • How do I move my documents from word to a PDF ?

    How do I change my existing documents to a PDF ?

  • Dropped iPhone 4s now screen is like this???

    My girlfriend has dropped her iPhone 4s out of her pocket and now the screen has gone like this... http://s1226.beta.photobucket.com/user/CalDrinksJuice/media/IMG_3475_zps6d792913 .jpg.html http://s1226.beta.photobucket.com/user/CalDrinksJuice/media/

  • ICal v2.0.3 buggy To Do List

    Haven't been using the to do list for a while, decided to use it today and it's giving me problems. Sometimes the color of the calendar (home, work, etc.) shows up, sometimes not. Several items seem to have duplicated themselves. I only typed them in

  • Oracle 9i OCI on Tiger (Mac OS 10.4.2)

    Hi, Does anyone have this working? I've installed the Oracle9i developer release because it seemed like the only way to get the client software for 9i on Mac OS X. I set up a TNSNAMES.ORA file and the ORACLE_HOME and DYLD_LIBRARY_PATH environment var

  • Prompt on close closing on no

    I am not sure what I am doing wrong here but if the user clicks no the program closes anyway. //Sets a propmt for closing the window          setDefaultCloseOperation(DO_NOTHING_ON_CLOSE);          addWindowListener( new WindowAdapter()            @O