Is possible to connect two i-phone4 with bluetooth?

Is possible to connect two i-phone4 with bluetooth?

For what reason.  Some apps were made to interact with another iPhone with the same app running over bluetooth.
All info is in the manual if you mean for other reasons.
http://manuals.apple.com

Similar Messages

  • How to connect 2 iPod classics with bluetooth

    I am trying to sync photos between 2 iPod classics, iPad4 and iphone 5 with blue tooth. The only devices that are seeing each other is the iPhone and iPad but still hasn't' synced the photos. Why re the apple devices not able to see each other?

    Havilah Farm wrote:
    Why re the apple devices not able to see each other?
    Because that's the way Apple have designed it. They have used a particular Bluetooth protocol that is designed to allow audio to be transmitted to Bluetooth headphones or Bluetooth speakers (for example) and some peer-to-peer gaming between the devices, but not the transfer of files.
    To transfer photos, Sync them via your iTunes programme. If you took the photos on the device, transfer them to your computer first and then Sync them with the other devices. For photos that were not taken on the device, they presumably were Synced from your computer originally, so simply Sync them to your other devices from the computer.
    By the way, your subject question: "how to connect two iPod Classics with Bluetooth"...
    You cannot. The Classic does not have Bluetooth.

  • Is it possible to connect two Macs via USB ?

    Is it possible to connect two Macs via USB just like Firewire back in the day via Target mode or is there something similar? I am asking this because about 2-3 years ago I would normally image Macs via Target Mode. I used to have a regular Macbook running 10.6 along with a customized-ready-to-go .dmg image saved on the Desktop. Whenever I needed to put that image into any Mac I would simply connect the two Macs via Firewire, I would then press "T" at startup which will get me in Target Mode, I would then see the disk appear in the desktop of the Mac I had the image. I would then copy that image to the T mode macbook using super duper. Can this still be done through USB with new models and if so will I also need to press T at startup ?

    No, USB connection does not qualify for this, only firewire and thunderbolt, as I read (but cannot test, for the time being I have only one such mac around).
    This is why the short series of alu MBs (2008) are not qualified for target mode either.
    p.s. What ‘new models’ do you refer to?

  • Is it possible to connect an external camera via bluetooth to the Iphone 4 and use it with Facetime, if not.. why?

    Is it possible to connect an external camera via bluetooth to the Iphone 4 and use it with Facetime, if not.. why?

    Ok, in 2015 is it possible now? I would like to use an iPad and Face to share content between a dressmaker in Asia and a customer in the US, and I would like to attach better camera's than the built-in camera's on the devices.
    Any thoughts? Any updates to the original post?
    Thanks,
    James

  • Connecting two Nexus switches with link

    Hi,
    I would like to connect two nexus switches with a link. Like one c5020 and one c5548p. How do i need to configure the ports at both the switches which will be joined with a fiber cable.
    For MDS switches such links becomes E-port and fabric is merged. Not sure what happenes at the Nexus swictches. Any input will be appreciated.
    Thanks,

    Do you have fc modules in each nexus? If so, they act much like the MDS 9148. All ports should be default auto speed and auto switchport mode. Insert fc-sfp's and a regular multimode fc cable between them. Default mode is fc switch.
    If that doesn't work, configure the mode on each port as E.
    Once done, the fc switch portion of each nexus will merge.
    Dave

  • It is possible to connect iphone 3G syncing with 2 apple machine?

    1. It is possible to connect iphone 3G syncing with 2 apple machine (1 imac which i using in home lower version &
    MacPro5,1 is i am using in office.) Please let know in which i can both the machine.
    2. And i not able to install any apps in which is compatability with iphone ios 4.2 ver.
    It says some error.
    Thanks & Regards
    JS

    By design, the iPhone syncs or manually manages iTunes content with ONE computer at a time. Thus, it is not possible to do what you want. You need to pick one computer & stick with that computer.
    You are correct, the iPhone 3G cannot be updated past iOS 4.2.1...the end of the line for that model iPhone. Thus, any apps that require a higher iOS version will not install or run on your phone.

  • Is it possible to install two SAP system with same SID but different instance numbers on one host?

    Is it possible to install two SAP system with same system ID (SID) but different instance numbers on one host?
    If yes, then how?
    If no, then why?
    Thanks in advance.
    Regards,
    Sarim

    Is it possible to install two SAP system with same system ID (SID) but different instance numbers on one host?
    Yes, it is possible. If one is CI (PAS) and the second one is an AS (AAS). In this case there will be only one database.
    If you are talking about two separate SAP systems with separate databases (Eg: A BI and an ECC) with the same SID then the problem will be with the database (Eg: Oracle)
    The database will be installed under /oracle/SID/112_64 (ORACLE_HOME) unless one database is running on 10 G and in that case the ORACLE_HOME will be /oracle/SID/102_64
    The next issue will be with the SAP file systems like /sapmnt/SID
    The most important problem will be with the switch to the sidadm and orasid users and the conflicts there. If there is a need to stop one of the SAP systems and if you do a switch to sidadm and issue a stopsap command which system will be stopped ?
    These are few of the many problems I can think of.
    So if we are talking about two separate systems with their own databases I would rule out the possibility of having two systems with the same SID.
    Regards
    RB

  • Morning, is it possible to connect your apple Ipad via bluetooth with a blackberry phone?

    Morning, is it possible to connect your apple Ipad via bluetooth with a blackberry phone?
    Lastly can you download from a wwindows computer to your Apple Ipad?

    No.
    You can use iTunes on a PC to sync content to an iPad.

  • Connecting two Nexus 5020 with 10G ISL link

    Hi Experts,
    I am trying to connect two nexus 5020 with a 10G ISL link.
    Per my understanding, with new release 5.0.3 N2(2a) ISL link between two nexus switch is supported.
    Following is my config
    c5020-1(config)# show running-config int vfc 32
    !Command: show running-config interface vfc32
    !Time: Fri Dec  2 01:14:38 2011
    version 5.0(3)N2(2a)
    interface vfc32
      bind interface Ethernet1/32
      switchport mode E
      switchport trunk allowed vsan 3040
      no shutdown
    c5020-1(config)#
    c5020-1(config)# sho running-config int eth1/32
    !Command: show running-config interface Ethernet1/32
    !Time: Fri Dec  2 01:16:15 2011
    version 5.0(3)N2(2a)
    interface Ethernet1/32
      switchport mode trunk
      spanning-tree port type edge trunk
    c5020-1(config)#
    I have similar config on the other switch. But for some reason the link does not come up. vfc port keep "initializing" and Eth port stays isolated.
    c5020-1(config)# sh int vfc32
    vfc32 is trunking (Not all VSANs UP on the trunk)
        Bound interface is Ethernet1/32
        Hardware is Virtual Fibre Channel
        Port WWN is 20:1f:00:0d:ec:ca:04:bf
        Admin port mode is E, trunk mode is on
        snmp link state traps are enabled
        Port mode is TE
        Port vsan is 3040
        Trunk vsans (admin allowed and active) (3040)
        Trunk vsans (up)                       ()
        Trunk vsans (isolated)                 ()
        Trunk vsans (initializing)             (3040)
        1 minute input rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
        1 minute output rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
          0 frames input, 0 bytes
            0 discards, 0 errors
          0 frames output, 0 bytes
            0 discards, 0 errors
        last clearing of "show interface" counters never
        Interface last changed at Fri Dec  2 01:17:28 2011
    c5020-1(config)#
    c5020-1(config)# sh int eth1/32 fcoe
    Ethernet1/32 is FCoE Isolated
    c5020-1(config)#
    If any expert throw some light to make me understand things better will be helpful.

    i have not connected two Nexus before but looking at your eth 1/32 interfaces ..do you think it needs to be "
    switchport trunk allowed vlan" your "FCOE" VLAN ?

  • Connecting MBA and iphone with bluetooth?

    connecting MBA and iphone with bluetooth?

    Do you have a question specifically?
    How does it work?
    Why isn't my configuration working?
    I'm getting an error message?
    What do I need to do to make it work?
    Otherwise, Yes.

  • Connect iphone4 to  MBP with bluetooth

    How can I connect iPhone4 to MBP with bluetooth? Can ipone4 use MBP's net service?

    You can only pair an iPhone to a computer, by Bluetooth, for the singular purpose of Tethering.

  • With MacBooks Retina 13" can you connect two external monitors with resolution each 2560x1600?

    I'm not talking about Thunderbolt displays, but other brands like ASUS, LG, SAMSUNG, etc.
    Has anyone tested?

    You can connect two displays to the two Thunderbolt ports with appropriate Mini DisplayPort cables or adapters.
    <http://www.apple.com/macbook-pro/specs-retina/>
    "Simultaneously supports full native resolution on the built-in display and up to 2560 by 1600 pixels on up to two external displays"
    If the display supports HDMI, you could connect one to the computer's HDMI port, but not at 60Hz.
    "Support for 3840-by-2160 resolution at 30Hz"

  • Why connect two dhcp servers with different IP addresses?

    
    so for an assignment at college we had to configure a router connected to two switches which both had a server connected to them.
    the computers were connected via dhcp to either server however each side had a different IP. we have now been asked to justify as to why two servers were used with different IP which I cannot quite produce a business orientated answer.
    I can understand connecting two dchp servers on same IP to increase fault tolerance but I do not understand using two separate IP addresses.

    Hi,
    Does “using two separate IP addresses“ mean 2 subnets which are connected by router？
    If you have separately configured 2 DHCP servers on the 2 subnets, and want 1 of the 2 DHCP servers to provide fault tolerance for the other. You need to use an RFC 1542–compliant router, or DHCP relay agent, in order to forward DHCP broadcast traffic.
    If there is any misunderstanding about your question, please correct. 
    Best Regards,           
    Eve Wang                                                                             
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

  • Connect two ECC systems with one SAP CRM 7.0

    Hi Gurus!
    I have to do a customizing for connect two ECC 6.0 and one SAP CRM 7.0, only I need the organizational structure from both systems and they need update when the structure from CRM has changes. The business partner goes to ECCs system by PI interfaces.
    Both organization models are different, so I have to maintain and update depending the changes in the business.
    But I don't know if this is possible, I don't know if we can do this by Middleware, ALE or PI.
    Can you please, give your oppinion about this topic?
    Best regards,
    Eugenia.-

    Hi Eugenia,
    Please see note 1084315 which descriibes the the multiple backend scenario.
    This should be relevant here.
    Best regards
    Christophe

  • Is possible to connect a Remote Ressource with Windows Phone 8.1 ?

    I am trying to connect the my mobile with Windows Phone 8.1 with a remote ressource (and not remote PC). The address is something like "https://xxx.xxxx.xx/...". This connection is possible wiith Androïd and Mac. Here I don't fond it.

    Hi,
    Current versions of Microsoft Remote Desktop Preview for Windows Phone 8.1 do not support connecting to Remote Resources. I will help to forward your concern to the product group.
    Best Regards.
    Jeremy Wu
    TechNet Community Support

Maybe you are looking for

  • Sharing a Printer between XP and Windows 7 computers on a Wireless Network

    Does anyone know if you can share a printer on a home network between a windows 7 and an XP SP3 computer? I had a wireless netowork set up at home with an XP desktop hardwired to a cable modem and a printer with USB connection. I also had an XP lapto

  • Can't get "Open in new window" to work

    Having my Macbook Pro on service I had to setup my good old Powerbook G4 again. The only stupid problem I have is that how ever I make the settings in Safari 5.0.1 it wont open any links in a new window. They always open in a new tab. Even is the lin

  • Iphoto Slideshow Won't Assign Music

    Ive searched the forums and tried all the reponses, but nothing has worked. I created a slideshow in iphoto (with most up to date software update). When I click to assign music, it will allow itunes to come up. I pick my music (from itunes), click ok

  • Easy way to log processing

    Hello all together, I have fileadapter with certain content. I want to ensure that the data in this file are processed exactly once. The argument for checking this is i.e. an invoiceNo. in the file. What would you propose is the easiest way to come t

  • Can i setup appriver server on ipad to receive my mail from work

    i am trying to setup to receive my work email on ipad2.  we use appriver . having trouble sending emails.