Is power supply 3k-X 715W AC hot swappable on Cisco 3750X?

Is power supply 3k-X 715W AC hot swappable on Cisco 3750X?
Thanks
Diego

Sorry, found the answer http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3750x_3560x/hardware/installation/guide/3750x_3560x_HIG/HIGFRU.html
The power supply is hot-swappable. In some configurations, such as full PoE+ or power sharing mode, removing a power supply causes powered devices to shut down until the power budget matches the input power of a single power supply. To minimize network interruption, hot swap the power supply under these circumstances:
–The switch is connected to an XPS 2200 and sufficient power is available.
–The switch is in StackPower mode and sufficient power is available (Catalyst 3750-X only).
–The switch is powered by other switches in a power stack, and no active backup is in progress.
For the switch commands for displaying the available power budget, see the Catalyst 3750-X and 3560-X Software Configuration Guide.

Similar Messages

  • MacBook Pro Retina power supply is surprisingly hot

    The power brick seems to get a lot hotter than my previous MacBook Pro power supplies. Anyone else noticing this?

    Just got my new 2013 retina MPB, and the powersupply is charging the battery in the MPB at an amazing rate (faster than 1% per minute) but holy Hephaestus batman that power brick gets lava-hot.
    This is my 10th Mac laptop (personal) and none of the other power supplies have ever heated up like this.  Other Mac laptop power supplies got very hot but never too hot to touch.  This retina power supply, at the temp it was at earlier today, would cause burns if left on skin.  So hot I am concerned about the plastic melting. Will check but I would not be surprised if when all the lights are off there isn't a slight glow to this lava powered adaptor.
    My retina seems to love it and it does not get hot in the least.  As i typed this message, the charge went from 40% to 67%. (freekin awesome) and the power supply is very warm but hot yet.
    I cannot help but wonder if this is not related to the powersupply on house wiring with the reversed phase...  My brick does not get hot all the time and not everywhere I plug it in.
    <Edited by Host>

  • Replacement Sawtooth G4 power supply - Specs?

    Hello!
    Well, a couple of months back, I discovered that the power supply fan in my 400mhz AGP (Sawtooth) G4 had stopped running. My interim fix? A powerful case fan, attached via Velcro to the outside of the case (sucking air out of the G4) with the power cable running through an empty PCI slot door. The open door and edges of this fan are sealed with strips of duct tape...
    Needless to say, this is not an optimal way to run the G4. After some looking online, I discovered that it's possible to buy refurbished/used G4 power supplies for around $90, but I'd rather not spend that much on a used power supply, particularly since this is actually the second power supply fan failure on this G4 - the first when the G4 was only a year old - so I'm not thrilled about buying the same model Apple PSU!
    On a visit to my local Fry's store, I noticed they had a large assortment of power supplies, and that they seem to be pretty much the same as the one inside the G4 now - makes sense.
    -My basic question is, can I use one of these basic PC power supplies in the G4? What, specifically, do I need to check to ensure that I don't blow anything out?
    -Also, is the "power plug" on the G4's logic board a standard configuration, or is it wired differently than the ports on other PC logic/mother boards?
    -The PSU inside the G4 says that it has a maximum output of 237 Watts and 32 Amps. I assume I need to purchase one that's very similar in output - how large of a difference between this PSU's power rating and the new PSU's rating is too large?
    -Finally, what kind of screwdriver do I need to pull the existing PSU out of the G4?
    Again, I have a 400 mhz "Sawtooth" PowerMac G4 from 1999, with a 16 MB AGP Rage 128 video card, and many upgrades. (DVD burner, more RAM, new HDDs, USB 2 card)
    Thanks a bunch,
    -Dan

    According to the linked Forum Topic, the SilenX brand fan (80mm x 25mm = 80mm square x 25mm thick) plugged directly into the power supply's circuit board without splicing wires. Even if you need to splice wires, you just leave enough of the original fan's wires intact by cutting them off close to the fan itself, then joining them to the identical wires on the new ones. Any store having electronic supplies will probably have the mini-wire connectors, that you slide over the spliced wires and crimp in place. Electrical tape doesn't hold up as well in hot environments. Don't leave any excess wire length laying about inside the power supply, touching some of the hot components. Use a small nylon wire tie to gather the excess wire together, and hold away from the circuit board's components. The power supply housing has two halves, that can be separated enough to access the fan, after removing some phillips machine screws. A Google search may provide a page with photos of the procedure. The case fan is 120mm square x 25mm thick. If you want to use the same connection point as the original, you may need to cut the wires close to the original fan and splice them to the new ones. Otherwise, those fans typically have a standard molex power connector, that readily plugs into an available power lead. When buying replacement fans, be sure to get ones that provide a high airflow (CFM rating) for the given speed (RPM) and noise level (db rating). The noise level is important, because even a new fan can be loud.

  • Monitoring 3750x and 3560x Redundant Power Supply and Fans

    I need help for monitoring the redundant power supply of my switches (3750x and 3560x)
    I have configured my snmp on my switches and is able to monitor interfaces, temperature and etc.
    The problem is when I am monitoring the redundant power supply and fans.
    I am using two Cisco C3KX-PWR-350WAC Modular Power Supply per switch.
    The OID I use to monitor the PSU are the following:
    Power Supply 1
    .1.3.6.1.4.1.9.9.13.1.5.1.3 Instance: 1003
    Power Supply 2
    .1.3.6.1.4.1.9.9.13.1.5.1.3 Instance: 1004
    When I do an SNMP walk, the value is showing (1) which means normal.
    When I simulate a power outage on power supply 1 or 2 by unplugging the power source, the value doesn't change and is still (1).
    Values: normal(1), warning(2), critical(3), shutdown(4), notPresent(5)
    As for the Fans:
    When I remove the fan module, I am able to get a notification that the fans are down, but when I plug back the fan module it is now using a different instance.
    Below is my config for SNMP:
    snmp-server community XXXXXXXXXXXXXX RO
    snmp-server location XXXXXX
    snmp-server contact XXXXXX
    snmp-server chassis-id Cisco3560X
    snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
    snmp-server enable traps transceiver all
    snmp-server enable traps tty
    snmp-server enable traps license
    snmp-server enable traps cpu threshold
    snmp-server enable traps syslog
    snmp-server enable traps vlancreate
    snmp-server enable traps vlandelete
    snmp-server enable traps port-security
    snmp-server enable traps envmon fan shutdown supply temperature status
    snmp-server enable traps errdisable
    snmp-server enable traps vlan-membership
    snmp-server host X.X.X.X version 2c XXXXXXXXXXXXXX
    Note: This problem is the same for all of my 3560X switches and 3750X switches. I am not sure if I am monitoring the wrong OID. 
    Thanks in advance

    Hi ,
    You are running an old IOS code , definitely you are hitting a BUG .
    there is no workaround or I would say unfirtunetely you will not be able to get the correct power supply status via SNMP.
    you need to use command line for this.
    I mean "show env all "
    **** if you want to know the Excat BUG that your code is hitting ,please contact TAC.
    Thanks-
    Afroz
    **Ratings Encourages Contributors ****

  • Cisco 831 Power Supply

    Hello,
    please i cannot find part number of Power Supply for Cisco 831.
    We need new one for this router.
    Thank you
    Tomas

    PWR-830-WW1= is the part number for the CISCO830 Series External Spare AC Power Supply.
    Below are some useful document URLs:
    Cisco 831 Router and SOHO 91 Router Hardware Installation Guide
    http://www.cisco.com/en/US/docs/routers/access/800/831/hardware/installation/guide/overview.html
    Cisco Cable Product Numbers, Part Numbers, and Descriptions
    http://www.cisco.com/en/US/products/hw/routers/ps332/products_tech_note09186a0080094b45.sh
    tml
    Upgrading Cisco IOS Software for the Cisco 806, 826, 827, 828, 831, 836, and SOHO70
    Routers
    http://www.cisco.com/en/US/products/hw/routers/ps380/products_tech_note09186a0080094b23.shtml
    Marcos Hernandez
    Technical Marketing Engineer
    Cisco Systems, Inc.

  • Does "dual power supply" mean "redundant power supply"?

    Does Cisco7301 "dual power supply" mean "redundant power supply"?
    If unplug one power socket, 7301 continues operating?

    Disclaimer
    The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
    Liability Disclaimer
    In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
    Posting
    On a 7301, I believe it does act as a redundant power supply, and this is often true for many Cisco devices with dual power supplies, but there can be exceptions.  For example, on the 6500 chassis, you might use dual power supplies in combined mode, i.e. failure of a power supply would leave the chassis short of necessary power.  The 3560X/3750X might also have insufficient power if a power supply fails when running on two (this issue may arise when using PoE).

  • Cisco 3850 Dual Power Supply - One No Response

    Hey Guys,
    I am getting multiple switches on my network showing "power supply failure" from Solarwinds.
    I am running Cisco 3850s running v 03.02.03.SE cat3k_caa-universalk9 iOS, and they all have dual power supplies. When i do the sh env power, I get this output.
    SWITCH1#sh env power
    SW  PID                             Serial#     Status               Sys Pwr  PoE Pwr  Watts
    1A  PWR-C1-715WAC       xxxx           OK                 Good     Good           715
    1B  PWR-C1-715WAC       xxxx         No Response   Good     Good           715
    SWITCH2#sh env power
    SW  PID                              Serial#     Status           Sys Pwr    PoE Pwr     Watts
    1A  PWR-C1-715WAC       xxxx           OK                   Good     Good          715
    1B  PWR-C1-715WAC       xxxx         No Response     Good     Good          715
    When I physically go down to look at the switches, they have green lights, so they are receiving power, but I keep getting the PSU failure alerts.
    Do you think it is an iOS issue, and should I upgrade? Or has anyone else seen this?

    Hi,
    I think below Bug could match with your issue.
    "power supply B is not responding" reoccurring on Catalyst switches
    https://tools.cisco.com/bugsearch/bug/CSCun41735/?reffering_site=dumpcr
    And we can see workaround of this issue is HW workaround.
    Thanks,
    Jack

  • Power Supply Temperatures Running Hot! Mac Pro shuts down.

    Hello,
    First I will give machine/hardware specs of interest:
    2 x 3 GHz Quad-Core Intel Xeon (pre 2009)
    8 GB 800 MHz DDR2 FB-DIMM
    NVIDIA Quadro FX 5600 (running 2 displays)
    Apple RAID Card/Controller
    SMC Version: 1.25f4
    *venting dimensions around computer: top=18", left side=3", right side=3" and back=18".
    Software of interest currently running:
    OS X 10.5.8
    iStat Menu
    SMC Fan Control
    My machine has been shutting down spontaneously and I suspect either CPU or power supply overheating. In the 5 instances this has occurred, the room was very warm (AC was not on) and I was running HandBrake with CPU at full and an iStat reading of 145 F. Ambient was 77 F and I was not reading power supply temps at the time. I figured for sure this must be a CPU overheating issue. However, just a few hours ago I had another shutdown. The room was warm again but I was not running Handbrake, but StarCraft II. I have played a lot of Starcraft II with no problems until tonight.
    I decided, this time, to check the temps on my power supplies. Power supply 1 = 147 F, and #2 is at 178 F. After many hours of searching forums I have concluded that these are crazy hot temps! I immediately installed SMC Fan Control to attempt to increase the fan speeds. I was successful in increasing all fans except the power supply (stuck at 599rpm). I have now turned the AC on in the house and the Ambient is down to 70, PS #1 145 and PS #2 169. All of these temps are a result of and idle machine running a browser.
    The following may or may not be an issue, however, leave no stone unturned. I currently have 12 external devices running on USB. 4 WD passport drives, 1 DVD writer, 5 WD powered drives plus the keyboard and mouse. Also, the Mac Pro is plugged into a small UPS.
    In all my forum searches, I just can't seem to answer some basic questions:
    1. Can an overheated power supply shut the system down?
    2. What are optimal (normal) running temps for Mac Pro's? (everyone seems to have opinions, but there doesn't appear to be a technical specification anywhere).
    3. I thought the fans, especially CPU fans, were supposed to kick in when the heat rises. Why are mine staying at minimal rpm's?
    Finally, does it look like I need new power supplies? Fans?
    This machine was put into service in March of 2008 and has done very intensive rendering for the film industry...long nights...rendering for days sometimes. It has been retired for over a year now and is used at a lesser degree.
    Thanks for reading this long post! I appreciate any input you can provide!
    Other iStat reading of interest:
    Power Supply 1 voltage = 12.28 V
    Power Supply 1 current = 26.44 A
    Power Supply 1 power = 316.75 W

    Also, the Mac Pro is plugged into a small UPS.
    Put your peripherals on that.
    Don't share the same circuit for A/C as the Mac Pro, and put the Mac on 1300VA UPS at least.
    As for all those external drives.... I'd consolidate into a good SATA case or two.
    And yes in summer run with 3 of the fans up around 900 rpm.

  • Macbook pro,power supply is very hot?

    macbook pro 15zoll with retina display, power supply is very hot! is this normal??

    It depends on what you are doing.  Yes, the power supply can get hot.  This is normal.

  • 45w power supply getting hot

    When I plug my 45w power supply into the extended cable it brick gets incredibly hot. When I plug it directly into the wall with the 2 prong plug it does not get as hot.
    Any suggestions as to what is going on?

    It will also depends on WHEN you are checking the brick.  If you check the brick after say, you have been watching Netflix movies FULL screen for the last 2 hours, it will likely be more hot than it would if you were just surfing around the internet.  Also, it would be warmer if it was currently charging the battery as opposed to JUST powering the computer.  It shouldnt matter if it is the long cable or the direct plug.  Last, define HOT?  What you consider HOT may not be hot at all to me.  It is a completely subjective thing.  Obviously if it is so hot that you cannot touch it, that is a different story.

  • Power supply get very hot!

    I just bought a Pavilion dv6-6c35dx laptop and have noticed that the power supply gets really really hot, to the point that it scares me and I disconnect the laptop. Does anyone has the same problem?

    Same problem here on my dv6-6c35dx.
    I didn't know about the power cord recall, and I bought a new ac adapter, power cord and replaced the battery. No change, the adapter gets really hot, too hot using the 2 second rule! Experienced chefs use it to determine if a grill is hot enough by touching it for no more than 2 seconds.
    I'm now putting it on a ceramic plate to make sure it doesn't smoke something when its charging. I hope HP knows this is a problem. Maybe the battery charging rate can be slowed and this may help.

  • Why does my power supply converter get so hot

    My power supply get very hot when it is plugged into an outlet. Will this hurt my Mac?

    http://www.bresink.com/osx/TemperatureMonitor.html
    http://www.macupdate.com/app/mac/20364/istat-pro

  • Dv6-3181nr, installed clear windows, all time hot on power supply

    Hey. I have a HP Pavilion dv6. I format my drive and lost factory recover. Now I have a clear windows 7, download a driver from official webstie HP and my lapotp all time hot when on power supply. I change past and clean inside laptop. 
    When instaled a HP Power Plan all time see not respondet.
    Need a facotry resore, recovery .
    Information my laptop :
    dv6-3181nr, serial CNF110389N, product number LS954UA#ABA
    On website HP if write my zip code to order, not found my country (Poland)
    Do you have OEM HP to my laptop?
    Windows 7 Home Premium 64 bit
    Sorry for my english.

    Hello dudek564,
    Thank you for writing in.  Your English is much better than my Polish.
    Take a look at this page, which provides restore information.  Please let me know if this helps.
    Good luck!
    ↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

  • 3750X stack with broken 715W power supply

    I have a stack of 2 WS-C3750X-48P      15.0(2)SE6            C3750E-IPBASEK9-M       
    Each switch has two 715W power supplies.
    It happened one power supply is broken and stuck all stack. Why ?
    Thanks to all
    Alberto

    Hi Charles, yes the 2 switches act like one stand alone sw
    Switch 1 connected to Switch 2
    and with the second cable,
    Switch 2 connected to Switch 1
    There are no stack power cables.
    IOS    c3750e-ipbasek9-mz.150-2.SE6.bin
    Log now is   000455: Apr 21 11:00:31.065 UTC: %PLATFORM_ENV-1-FRU_PS_ACCESS: FRU Power Supply is not responding
    I have only one electrical line to the rack
    The problem is that a broken power supply caused to switch off all the rack.
    In fact the master electrical switch of all the rack went down.
    Last 3 months the same problem  happened twice to two different stacks.
    Is it possible a firmware bug ?
    Tell me if you need further info. Thanks a lot
     Alberto

  • Hot Powerbook G4 & power supply

    My Powerbook G4 15-inch is about 5 or 6 years old, and just recently both the power supply and the computer get very hot when they are plugged in. Both would get hot in the past, but not like this: painful to have on your lap, hot. It is not the battery that is getting hot on the computer - the location of the heat is more under the keyboard and towards the edge of near the screen (and I just bought a new battery for the computer about 4 months ago). I am wondering if this is the early warning of the computer starting a downward decline.
    Thanks,
    Garp

    Run this Temperature Monitor Application by Marcel Bresink Software
    http://www.bresink.de/osx/TemperatureMonitor.html
    It's the greatest little digital temp monitor that runs at top of screen edge.
    I've used it for over a year. This is by far the best one.
    I've tried others at Apple that never performed.
    After you monitor the heat range of the processor a few times, you will have abetter idea of what to expect.
    Viewing video from Youtube, or Apple's training will run the temp up to 151 degrees.
    Or converting RAW images in Aperture to file.
    Apples training http://www.apple.com/aperture/tutorials/#adjustedit-recover example test.
    Idle, waking up will see temps of 80.
    I run a quiet blower moving air under the laptop to help out if I hear laptop fan start.
    On lap or other areas, it's easy to block or restrict airflow and it will run hot.
    Using a lap pad available online works great. Helps keeping laptop in place as well.
    If power supply is running too hot, it's best to just replace it.
    There are plenty of reports, including mine made a difference.
    Make sure to use the 3 prong grounded power cord adaptor to supply rather than the folding 2 prong adaptor. There is a weak point inside the 2 prong adaptor.
    Plug power supply to wall outlet first, then laptop.
    When you hear arcing, plugging power supply into wall outlet, this is normal.
    Hearing multiple arcs is danger mode.
    This arcing can spike laptop if it's plugged in at laptop first if you have sloppy fitting wall outlets
    using the flip out 2 prong adaptor.

Maybe you are looking for

  • What I would want to see in a new XFI driver relea

    Well obviously fixes to all the issues everyone is having BUT.... I like the mode changer actually. I usually play games with headphones on but sometimes I dont. I have some nice Klipsh speakers and a 00 watt amp I can listen to my stuff through. So

  • IPod does not charge nor shows up in Windows or iTunes

    I bought a iPod nano 2Gb two days ago. After some trouble shooting I got it to work and was able to get some music on the iPod. After using the iPod yesterday I wanted to recharge the battery. Since the computer was still on I reconnected the iPod th

  • Third party system throwing error " No Direct Postings can be made in G/L "

    Dear all i have a problem,  when doing third party ,In me21n purchase order screen i am getting an error " No direct postings can be made in G/L a/c 41201100 in CoCode ." and when i checked the G/l account  tht G/L account stands for " Change in Stoc

  • CIN: excise invoice J1IIN     URGENT

    While i am creating the excise invoice (J1IIN) following error is occuring. Error in allocating internal document number Interval not found Number object J_1IINTNUM And the document is not get saving. Sunil

  • Problem with Photoshop

    I have an old photoshop 6.0 it's ok with my old computer windows XP but, it's impossible to install on my new computer with Windows 7 64 bits. could you help me please.