Is that possible to do the cross domain migration for AD RMS Services?

Hi guys, recently i am doing a cross domain migration, when i listing out the server, i found the server have AD RMS services which is still active.
but after my migration is complete, it is planned to do the decommission on all the old server
After my checking, i believe the AD RMS have trust establish with a cross site domain already. What i am planning to do is try to do a migration on it.
i have do some research on it an i found "Cross forest Migration of AD RMS document"
what i found in the document, it have mention about
In the event when one cluster running AD RMS is to be discontinued, users may still want to access
previously protected content that was issued a publishing license by that computer. Servers in other clusters can then add the to-be-discontinued server as a trusted publishing domain.
So i was wondering if there is an option for Ad RMS services to select a server or host to discontinued?
The scenario in my head now,
1.Build trust between in my new domain AD RMS with the existing AD RMS. update the certificate between the trusted domain as i mention above with my new domain AD RMS.
but i was wondering if i power down or decommission the server what will happen?
2. the worst case scenario will be decommission the old AD RMS service, and publish the new AD RMS services in new domain, simply build trust with the cross site domain.
any suggestion on this? which case is more workable?
Thanks
Dave

Hi,
I think you may ask in AD RMS forums:
http://social.technet.microsoft.com/Forums/en-US/home?category=rms&filter=alltypes&sort=lastpostdesc
Regards.
Vivian Wang

Similar Messages

Is that possible to display the user selection data in the printable page?

Hi All,
I'm going to add a printablepage button on my page.
Here comes a questions.
Is that possible to display the user selection data in the printable page?
For example,
I have a table in the page,with 10 records.User select 5 of them.Can I display these 5 records in the printable page?
Please help.

Hi Yannick,
Thanks a lot for the information. It worked.
The portlet data can be accessible using bindings, but parameter name can be different.
Meanwhile I have got one more scenario, where the Portlet and Task Flow placed in different pages of WCP Application. On change of data in the Portlet the application should navigate to another page where the Task Flow placed and displays selected data.
Basically I can not use any button for navigation. The navigation should happen once I do some action in Portlet.
Is this possible? If yes can you please let me know the steps?
Thanks in advance!
Somnath
Edited by: Somnath Basak on Dec 20, 2011 9:41 AM

I just download the Adobe Creative Cloud in my computer. As I live in Brazil, the software is in portuguese, but I'd like it in English. Is that possible to change the language? Thanks a lot.

I just download the Adobe Creative Cloud in my computer. As I live in Brazil, the software is in portuguese, but I'd like it in English. Is that possible to change the language? Thanks a lot.

CC desktop lists applications as "Up to Date" when they are not
-http://helpx.adobe.com/creative-cloud/kb/aam-lists-removed-apps-date.html

Is that possible to allow the Good Receipt on customized return Mvt Type

Hi All
Is that possible to allow the Good Receipt on Customized movement Type, Reference string for these movement type is 601
and these customize movement type has bee flagged for reveres movement type indicator under Internal Control and Under Update control consumption Posting is set as G "Planned consumption"
Thanks in advance

Hi There
As per the STD SAP,,
601 Goods issue for delivery (SD)
This movement cannot be entered manually. It is created automatically in SD using the function "Goods issue for delivery".
The quantity is taken from unrestricted-use stock.Possible special stock indicators: E, K, Q
You could have copied the 602 istead of 601,,
However if you are planning for the receipt (Returns from customer) you can use the Mov type-651,, if you want to have diff Acc assignments, you can copy this to Z movements,,
Hope it helps
Thanks
Senthil

I have a newer MacBook Pro and I am trying to download my Final Cut Pro 7 Studio 2 on it. Is that possible or does the new MacBook Pro not support anything other than Final Cut Pro X?

I have a newer MacBook Pro and I am trying to download my Final Cut Pro 7 Studio 2 on it. Is that possible or does the new MacBook Pro not support anything other than Final Cut Pro X?

As Tom said the FCS forum is the better place to post the question.
Here is Apple's best practices doc for installing both on the same system.
BTW, FCP7 is part of the FCS 3 suite of apps.
Russ

Cross Domain error for Silverlight + MVC application with self hosted WCF service on azure

Hi,
We are migrating existing Silverlight application to MVC; existing Silverlight application is hosted on
Azure which is consuming self-hosted WCF service. For authentication we have implemented
ADFS with WIF (passive). The cloud service (<myWebSite>.cloudapp.net) is C Name to (<myWebSite>.<myDomain>.com) and we
are consuming WCF service at <myWebSite>.cloudapp.net/<myService>.svc, as we were getting “Cross Domain” error so we have added “clientaccesspolicy.xml” at the root of “WEB ROLE”.
Existing Silverlight application works fine but the problem occurred when we deploy our migrated application to the same cloud service. We are getting a “Cross Domain” error.
The same migrated application works fine on UAT environment, the only difference is UAT environment is
without ADFS WIF implementation.
Migrated application is half Silverlight and half MVC with initial landing page is Silverlight. MVC web role is used to host the service i.e. .SVC . To go to SL landing page , redirected from home controller. Following is being observed in fiddler for this
application
Existing Silverlight application -
After authentication with ADFS it redirect to Silverlight landing page.
Before calling service method it looks for “clientaccesspolicy.xml”
In response header we are getting the content of “clientaccesspolicy.xml”
And after this everything works fine
Migrated Silverlight-MVC application –
After authentication with ADFS it redirects to “HomeController” and from there we are redirecting to Silverlight landing page.
Before calling service method it looks for “clientaccesspolicy.xml”
In response header we are getting following content - “https://federation-sts.<myDomain>.com/adfs/ls/?wa=wsignin1.0&
wtrealm=https%3a%2f%2f<myWebSite>.<myDomain>.com&
wctx=rm%3d0%26id%3dpassive%26ru%3d%252fclientaccesspolicy.xml&wct=2014-03-17T10%3a36%3a04Z”
4.Throw “Cross Domain” error.
Also we have added filter in
RouteConfig
for .xml file
routes.IgnoreRoute("{*allxml}",
new { allxml = @".*\.xml(/.*)?" });
NOTE: There is no configuration change apart from MVC configuration.
We have done RDP to web role and found that “clientaccesspiolicy.xml” is present at “E:\approot” location and it is also accessible at “https://<myWebSite>.<myDomain>.com/clientaccesspolicy.xml”.
Please help
Thanks,
Rahul P

Hi,
Please try to configure the cross domain policy file to allow public read access (that is, access it without federation requirement), make sure you can access the address
http://something/clientaccesspiolicy.xml directly in a browser
without redirecting to check whether the cross domain policy file could be anonymous accessed (Please start a new browser session and make sure you're
not logged in. Then test the cross domain policy file.).
Best Regards,
Ming Xu
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

How and when to load cross-domain.xml for web services.

I'm accessing some 3rd party web services and so I need them to have a cross-domain.xml file, which they have done.
In order to access their web services, am I correct that I need to load the cross-domain.xml file they put on their web server, and if so, is my code to do so below correct, which I put in my creationComplete handler function?
Note, of course the IP address in my code is not 0.0.0.0.
Do I need all these lines, and am I doing this correctly?
Currently I am getting a SecurityErrorEvent.
Security.allowDomain("0.0.0.0");
Security.loadPolicyFile("http://0.0.0.0/crossdomain.xml");
var request:URLRequest = new URLRequest("http://0.0.0.0/crossdomain.xml");
var loader:URLLoader = new URLLoader();
loader.addEventListener(Event.COMPLETE, policyLoaded);
loader.addEventListener(IOErrorEvent.IO_ERROR, policyIOError);
loader.addEventListener(SecurityErrorEvent.SECURITY_ERROR, policySecurityError);
loader.load(request);

Okay, I found that when I put the crossdomain.xml file at the root of my web site file area my hosting company provides, I do not specifically need to load the crossdomain.xml file.
But if I want finer control over who has access to what, and I put the crossdomain.xml file in the same directory as my Flex app SWF file, what lines of the following code (or additional lines I don't know about) should I put in my app creationComplete handler function to load the crossdomain.xml file?
Note, of course the IP address in my code is not 0.0.0.0.
Do I need all these lines, and am I doing this correctly?
Security.allowDomain("0.0.0.0");
Security.loadPolicyFile("http://0.0.0.0/myAppFolder/crossdomain.xml");
var request:URLRequest = new URLRequest("http://0.0.0.0/myAppFolder/crossdomain.xml");
var loader:URLLoader = new URLLoader();
loader.addEventListener(Event.COMPLETE, policyLoaded);
loader.addEventListener(IOErrorEvent.IO_ERROR, policyIOError);
loader.addEventListener(SecurityErrorEvent.SECURITY_ERROR, policySecurityError);
loader.load(request);

I am putting together a slide show using iphoto and I wanted to add a description on each slide/photo. How can I do that? Also on the choice of music for the silde show, if the slide show is longer than one song can you chose a different song for backgrou

I am putting together a slide show using iphoto and I wanted to add a description on each slide/photo. How can I do that? Also on the choice of music for the silde show, if the slide show is longer than one song can you chose a different song for background music?

This might help
http://www.apple.com/findouthow/photos/#slideshow
Regards
TD

I have a iMac 21,5" Intel mid 2011 and I need to know if is possible I change the original 500Gb HD for a 512Gb SSD? If yes, where I find a tutorial about this? Thanks a lot and best regards all.

Hi people,
I'm typing from Brasil, sorry my English.
I have a iMac 21,5" Intel mid 2011 and I need to know if is possible I change the original 500Gb HD for a 512Gb SSD?
I intend to keep the original DVD driver and install the SSD in the same HD place.
If yes, where I find a tutorial about this?
And I will like to know if the 512GB Solid-State Drive Kit for Mac Pro is compatible with iMac.
http://store.apple.com/us/product/MC731ZM/A/512gb-solid-state-drive-kit-for-mac- pro?fnode=5f
What brand and model of SSD do you recommend?
Thanks a lot for now and best regards all.
Carlos Sgrillo
Porto Alegre, RS, Brasil

Tukaine
Sep 23, 2012 10:59 PM
Since the late 2009 iMacs came out, replacing the hard drive has caused the internal Hard Drive Fan to start running at around 6000RPM.
This is due to Apple replacing the external Hard Drive temperature sensor with a proprietary firmware and using the drives internal sensor.
Replacement drives do not contain the firmware to deliver temperature data on the temperature sensor cable.
When the iMac does not receive a good signal from the hard drive it puts the fan at full speed to protect the drive.
If you replace your drive, your iMac will initially seem fine, but soon the fan will begin to speed up to full speed. Resetting the SMC (System Management Controller) will have a temporary effect, but again the fan will speed up.
Fixes people have used in the past included:
Using smcFanControl and the terminal to set a MAX speed for the fan and writing scripts to start this after every sleep/restart.
Shorting the temperature sensor cable (Not a possibility on 2011 iMacs) this tricks the iMac into thinking the drives temperature is very low, hence slow fan speed.
Both these fixes are less then perfect and leave the drive in a dangerous situation with no protection from overheating.
Another option people try is other Fan Control software. These programs will not work for this particular issue as they often only control the base speed, and if they do control the fans actual speed they rely on the temperature reported by the sensor which is now incorrect.
HDD Fan Control
HDD Fan Control works to fix this issue by reading the drives internal temperature using the S.M.A.R.T protocol and set the fans actual speed to a value good to protect the drive.
It runs at startup and continually to always control the fan correctly, prevent the loud fan noise and protect the drive from overheating
Instead of HDDFan Control, get the free SSDFan Control
http://exirion.net/ssdfanctrl/

I reset my disabled ipad 2 and it is asking me for the apple id which first set it up but i forgot the password for that apple id and the password/recovery information for the recovery email address. What can i do?

i reset my disabled ipad 2 and it is asking me for the apple id which first set it up but i forgot the password for that apple id and the password/recovery information for the recovery email address. What can i do?

Click here and use Apple's iForgot service, or contact their Account Security team, or if you're the device's original owner, take it and its purchase receipt to a physical Apple Store.
(124525)

Is it possible to change the Costing Lot size for preference calculation?

Hi Gurus,
Is it possible to change the costing lot size for the preference calculation?
Reason for my question is: We have all prices on price unit 100
and we want to use also the price unit 100 for preference calcalation.
But the preference calculation always take price unit 1.
Is there any possibility to set somewhere the costing lot size for pref.calculation?
Thanks
Regards
Dieter

Does really nobody has a hint?

An unexpected exception occurred while attempting to locate the run-time information for this Web Service. Error: java.lang.reflect.InvocationTargetException:null

Hi I m getting the below wxpection when i run test browser from workshop. please help me.
An unexpected exception occurred while attempting to locate the run-time information for this Web Service. Error: java.lang.reflect.InvocationTargetException:null

Thamarai,
Can you provide more information on your jws ? Also can you start the server
from the command line with verbose option. This will cause
weblogic_debug.log to be generated in the domain folder.
Raj Alagumalai
Backline Workshop Support
"Thamarai Selvan" <[email protected]> wrote in message
news:[email protected]..
Hi I m getting the below wxpection when i run test browser from workshop.please help me.
>
An unexpected exception occurred while attempting to locate the run-timeinformation for this Web Service. Error:
java.lang.reflect.InvocationTargetException:null

ISE and authenticating against Windows AD with RADIUS realm that is different from the Windows domain

Hello
We are in the process of evaluating the Cisco ISE VMWare appliance with a view to replace our existing FreeRADIUS installation as authentication provider for our wireless network and VPN service. As a part of this we are hoping to migrate our user authentication to Microsoft Active Directory - we have previously authenticated against a different identity store (not MS AD). Because of this legacy our Windows domain is not the same as our RADIUS realm name - the Windows domain is "win.mydomain" whereas we wish to allow users to authenticate using "username@mydomain" or even "[email protected]" as they are doing today. We are experiencing an issue where authentication requests with the format "[email protected]" will be forwarded to the Windows AD whereas authentication requests with the format "username@mydomain" will fail with the log message "User not found in Active Directory". We do not know if the ISE itself is validating the username and triggering this error, or if the error originates from AD. We suspect the that the ISE is not even asking AD because "win.mydomain" is the domain configured in "Active Directory" in "External Identity Sources".
Authentication requests against the AD without a realm are successful (that is, using only "username"). With this in mind we located a post on the Cisco support forums that described a process of proxying the request back to the ISE and strip the realm information, but this was specific for the ACS platform. We have attempted to implement this solution but it is still not working as we would have hoped, and we are not entirely certain where the fault might lie. We are currently using PEAP with MSCHAPv2 for authentication in our WLAN where the main problem is. We suspect that the "proxy-to-self" with realm stripping is an issue with PEAP.
Is there a supported method of achieving our goal, or should we abandon the ISE platform as our scenario is simply not supported?

Seems like your issue maybe related to DNS, when ISE receives the format [email protected], the dns request is failing. However, there is a setting for alternate UPN Suffixes that can be configured to include domain.com and student.domain.com.
Here is a windows article that should fix this for you. Once you get this updated please reboot ISE so it rejoins AD. Try your tests again.
http://technet.microsoft.com/en-us/library/cc772007.aspx
Thanks,
Tarik Admani
*Please rate helpful posts*

Firefox preference for the cross domain js call between iframes?

for my web application i need to access the contents of iframe which is loaded from the another application running on different port. i am using the javascript to access the contents of the iframe. all i need is the any preference is there for this.
Note: Both applications are running on the same host but different port. i know the document.domain solves the problem. but i have lot of pages may be 1000 or even more. its pretty big product. so i canot set in each and every page. so i created one extension for our product. so any preference is there then i can set the preference while installing the plugin. it solves the problem.

A good place to ask advice about web development is at the MozillaZine "Web Development/Standards Evangelism" forum.
*http://forums.mozillazine.org/viewforum.php?f=25
The helpers at that forum are more knowledgeable about web development issues.<br>
You need to register at the MozillaZine forum site in order to post at that forum.

Cross Domain Migrations - Able to access own mailbox but no other resource

Hi,
I wondered in anyone could offer any guidance on a problem we are seeing with a
cross forest Exchange 2010 (domain A) to Exchange 2013 (domain b)migration.
Our problem is based around the fact that the users are still logging into 'windows clients' in the source domain (domain A). We have configured mail enabled users in the source to enable auto discover to work correctly and the user can successfully
connect to their own mailbox once it is provisioned in Exchange 2013 (domain B). Our main Outlook client being 2010 SP2.
The user is not prompted to login at this stage, which is preferred.
However the problem is that they cannot connect to any other resource in the Exchange 2013 (domain B) environment. (We have no interest in them accessing resources in the Exchange 2010 environment as this is a major switchover). When attempting to connect
to public folders (2013) they receive only those permissions provided by the 'Default' user permission. When trying to expand a mailbox where full access has been granted they receive the 'Unable to expand. An attempt to logon to Microsoft Exchange
has failed' error.
If we change Outlook to 'Always prompt for logon credentials' and then login with credentials from the target domain (domain B, all resources can be accessed successfully.
As part of our migration we have used ADMT, a two way trust is in place, SID history has been migrated and SID filtering is turned off in both directions. Passwords in both domains are matching by virtue of an Identity management solution. Outlook anywhere
on exchange 2013 is set to negotiate (internal and external) with IIS configured with 'Basic, NTLM and Negotiate' as authentication types.
Whilst the obvious answer is simply to get the users to login to the target domain (domain B), it is unfortunately a requirement that users continue to login to the source domain (domain a) for a while after the Exchange migration has completed.
Would anyone be able to advise if this is just something we have to live with and find a way to force users to login every time they open outlook, or is there perhaps a way to configure this to work so that users are not prompted to login but can access
all their resources.
Many thanks for any assistance or opinions.
Kind Regards,
Mark Needham

Hi Mark,
Please try to clean up the cached credential in your computer. Then fill in with new domain information (domainB\user) when it prompted for credentials next time and check the Remember my credential to save it. About how to remove cached credentials, please
follow these steps:
1. Launch the Credential Manager from Control Panel > All Control Panel Items > Credential Manager.
2. In the Generic Credentials section you’ll see a setting for [MS Outlook] which will include your SSO details. Click the downward-pointing arrow to the right of that value.
3. In the expand details, click Remove from vault. Then Outlook will no longer have a stored copy of your old login information (domainA\user).
If it doesn’t work, please change the windows account with domainB\user information to have a try.
Regards,
Winnie Liang
TechNet Community Support

Is that possible to do the cross domain migration for AD RMS Services?

Similar Messages

Maybe you are looking for