Is the AC Adaptor Plug and Play?

Can the powerbook be up or should it be shutdown when plugging the ac adaptor in and out of the powerbook? It seems that with a functional battery the voltages would be similar enough to avoid a glitch but I thought I would ask, this being my first notebook computer.

Hi, rtdrury, and welcome to Apple Discussions. You can connect or disconnect the AC adapter at any time, as long as your Powerbook's battery has some charge in it, without any harm of any kind. If you disconnect it while the computer is in use, the computer will instantaneously switch over to battery power, and no unsaved work will be lost.
The adapter should be plugged into a wall outlet before you plug it into the computer, and disconnected from the wall outlet after disconnecting it from the computer. Doing things in this order avoids discombobulating the power management unit in the Powerbook.

Similar Messages

What ever happened to plug and play, or simple english to explain the tech stuff.

What ever happened to plug and play, or simple english to explain the tech stuff.

plug and play. well that is a windows term.. Apple decided they didn't need uPnP on the Time Capsule because that is just so windows.. so they use there own system.. called NAT-PMP.. (port mapping protocol). Just to make sure that things like playstation, xbox, etc could not open ports properly. And windows machines of course should be excluded from playing.
http://en.wikipedia.org/wiki/NAT_Port_Mapping_Protocol
"simple english".. unfortunately networking requires the use of a fair number of terms people are just unfamiliar with.
The big lie was computers and networking are easy. Computers in isolation might be fine.. but as soon as you link things in networks.. it gets much harder.. and people who do study for a couple of years just to diploma level in networking haven't done it because they are dumb and could have read the simple english manual overnight. But because it is complex.
I try and explain it this way.. if your washing machine goes bung, do you start pulling it to pieces and trying to find the fault.. or do you call the washing machine repairman.. who has trained to fix washing machines.
If your computer or networking goes bad.. then "who are you going to call?" The manufacturer and complain about how hard it is to setup a $100 piece of equipment and expect them to give two hours of hand holding for free on the phone. People would never call a computer support technician.. no this is easy.. it is in simple english somewhere.. and you only need to spend an hour and all will be fine. Even though you have as much training in networking as in washing machine repairs. Would you call the washing machine manufacturer and expect 2 hours of free phone support for you to strip down their washing machine.. after all it cost 6x times what the router cost?? Or has some strange lie grabbed hold of you that this is simple.

Plug and Play not showing up on desktop - camera, jump drive, etc.

Hi all:
On my Macbook Pro, none of the so-called "plug and play" devices show up on the desktop as they normally would on a Mac computer. I tried my ipod, camera, and usb jump drive. Is there a setting that I could have set on to make it like this??
Any help is GREATLY appreciated.
Thanks.

Welcome to Apple Discussions!
Go to Finder>Preferences>General, and you will find some boxes to check so that external devices will show up on the desktop. I'm not sure your camera would show up on the desktop--but it will appear in iPhoto if you want to put your pictures in iPhoto. Your iPod and jump drive will show up for sure.
Good luck!

How do I set MacBook to an external display when the plug and play doesn't recognize it? I am trying to set my Samsung 530 LCD as a monitor but HDMI and VGA cords (and the adaptor for them) doesn't seem to work.

I have tried everything I can find on line but they all claim that the plug and play works, and they don't for me. I tried the mini dvi to HDMI and a HDMI cord and that was not recognized no matter which unit I rebooted first. I found someone who said that my Macbook might be too old for the HDMI technology so I returned the cords and went to the VGA cord and adaptor.
I tried this first with the HDMI setup:
http://support-us.samsung.com/cyber/popup/iframe/pop_troubleshooting_fr.jsp?idx= 167919&modelname=LN40C650L1F&modelcode=&session_id=NDhJrD0DQT0Z8KRsm62yhxJxqnyPy SKhlhpB8vQ6h9Q7R2BZJGzj!-1089109758!1761676444!7501!-1!434477884!1761676348!7501 !-1!1292098185857
Then I tried this with the VGA setup:
http://support-us.samsung.com/cyber/popup/iframe/pop_troubleshooting_fr.jsp?idx= 167901&modelname=LN40C650L1F&modelcode=&session_id=NDhJrD0DQT0Z8KRsm62yhxJxqnyPy SKhlhpB8vQ6h9Q7R2BZJGzj!-1089109758!1761676444!7501!-1!434477884!1761676348!7501 !-1!1292098185857
I contacted Samsung support and they said I needed to set the display settings to external display on the mac. I went to the display settings and moved the icon to my status bar. When I click on search for displays or whatever it says (I'm not at my Mac right now) it does nothing.
What am I missing?

I am using MAC OSx 10.5.8 (9L31a) as my operation system. The TV says "No signal. Check connected device's power, cable connection and source selection." Seems to me that that goes in hand with what the Samsung tech said about the Mac needing to be forces to use the external display. But how do I do that?

I have a new iPad Air. Can I use plug in USB camera reader to have a load of movies etc on an external hard drive and then plug and play so to speak. I'm off on holiday and haven't got the capacity to have everything on that I'd like for the kids

Can I use a plug in USB camera reader to have a load of movies etc on an external hard drive and then plug and play so to speak? I'm off on holiday and haven't got the capacity on the iPad to have everything on that I'd like for the kids.
So basically I want a hard drive with X amount of films etc on. Can I then watch them on my iPad?
Hope this makes sense.

External HDD won't work.
You need something like this:
http://www.seagate.com/goflexsatellite/

How can I configure and control a non-plug and play VXI card using the NI-controller (NI-VXI/NI-VISA software)?

Defining the slot, logical address and sending data across the card bus are the main operations I would like to perform. The non plug&play card is a VXI send & receive slave card. Low-level programming is probably required. Has anyone tried this before? If so I would be so grateful if you could share your experiences or refer me to someone who has.
Thank you for your time and help,
Nandeesh

VXI cards are, by specification, plug and play, so I'm not exactly sure what you mean by a "non plug&play card." I'm guessing that the card is effectively a VME card. In this case, you can just add the VME device in the proper configuration utility. Here is a link to a document on our website about configuring VME cards (http://ni.com/support/vxi/vmeinfo.pdf).
You should easily be able set the slot, pseudo Logical Address and memory space. Once configured, you should be able to write to registers using NI-VISA commands (viIn, viOut, and viMove). These high level commands are included in the highreg.c example which shipped with your NI-VISA software (installed in vxipnp directory).
I hope this helps.
Trey Hamilton
National Instruments
Applications Enginee
ring
http://www.ni.com/support

Ever since I updated to the IOS 6, I no longer can play my music in the car! It is plug and play! It just sits there saying connecting and nothing happens. A few of my friends have said the same thing. Help please! Any ideas?

Ever since I updated to the IOS 6, I no longer can play my music in the car! It is plug and play! It just sits there saying connecting and nothing happens. A couple of my friends have said the same thing. Any ideas? Help please!

Hello ..do you have a history on the phone? did you get it wet? was it dropped? have you been using an authentic ORIGINAL apple charging cable?
this problem occurs when there is a short circuit in the phone... you most likely got it wet at some point and maybe didnt even realize it? The moisture in the phone hasb probablly oxidized one or several capacitors, integrated chips thereby short circuiting the phone. that is why he phone is acting erratic because these short circuits inadvertently "activates" other circuits.. eventually the phone will not turn on anymore- the heat will stress the citcuit board and you will have discontinuity along your main power lines and the phone will cease to function..i see this alllll the time in our shop
the fact you upgraded to ios6 will even work the phone harder because its a more powerful operating system taking full advantage of the A4 chip..

My classics IPOD has died over the weekend and I plan to but an IPOD Touch -- but need to to 'work' and simply sync all my 'old' music on a plug and play basis -- or is that wishful thinking ? I need it urgently for a holiday so only time to buy it n run

Any advice on :
1. The Touch as a product
2. The likely chances of plug and play resync to new device without hours of 'fiddling' / support calls
or I can just use my Shuffle I guess ----

There should be no problems, make sure to have all the needed software updates for Windows and the new iTunes 10.5 installed before connecting your iPod touch.
You already know how the basic sync process is working, there are a few more features added like mail for example: iOS: Syncing with iTunes

Help file for the Plug and Play driver of Agilent Technologies E5071C

I just download the Plug and Play driver of Agilent Technologies E5071C from the below link:
http://sine.ni.com/apps/utf8/niid_web_display.model_page?p_model_id=5692
I find that there is only some examples and not any help file with detail description for each input of those VIs. Although there is brief description for each VI when I press "Ctrl+H" on the VI,I still can't figure out how to use this driver. :-(
Is there any help files with more detail description?
Or any related examples for my reference? I hope to measure the S11 and S21 of the SMA cables

The driver implements the commands defined by agilent.
So look in the agilent programmers manual to find the meaning and how to handle the instrument.
greetings from the Netherlands

Is the 595759-001 DVD burner for Elitebook 8540p plug and play

I have a DVD ROM player, only, in my Elitebook 8540P, and I just ordered a DVD writer (595759-001) to replace it with. Do I just install the hardware? Is this going to be a plug and play experience, or do I need to locate drivers for the replacement? Do I need to uninstall the driver for the original DVD ROM?

Hi, The driver for any optical drive is provided by Windows, so you should just have to connect the new device, however it can sometimes avoid any issue by doing this as follows. Hold down the Windows key and press R. Into the Run box type devmgmt.msc and hit enter. Expand DVD/CD=ROM drives, right click the existing device and select Uninstall. When done, shutdown the notebook and fit the new optical drive. When you then boot Windows, give it a few minutes to fully load and you should find the new drive is up and running. Regards, DP-K

I plugged a usb controller into my mac and the vibrate function is not stopping. Do macs not support plug and play?

I'm still very new to forums so please excuse anything that may have been previously asked. I purchased a USB controller for my mac to play a couple games and the vibrate function on the controller will not stop. I was wondering if there is a way to access the controller setting or if os x supports plug and play controllers? Any help is greatly apprectiated.

Hello Knowledgelink
Go through the steps in the article below to restart your iPhone into recovery mode to then restore your iPhone to the latest version of iOS.
If you can't update or restore your iOS device
http://support.apple.com/kb/HT1808
Regards,
-Norm G.

Failed to plug and play with my Yamaha PSR-500. What do I need?

I'm trying to connect my Yamaha PSR-500(A relative unknown keyboard even on the Yamaha site) and the plug and play function doesn't work. I did a internet investigation but al the things I found where useless...
-The keyboard is old.
-I use a MIDI-cable.
-iMac doesn't recognize the keyboard.
-Had the same problem with my ex-windows computer but then I found a good windows software...
Greatings and have a great night,
Nathan

I'm sorry but the Yamaha website distinctly says that the PSR500 has NO USB Connector.
It does have a midi interface in the form of IN and OUT jacks - 5-pin DIN type.
(These seem to be labeled the wrong way round. Either that, or my HOSA adaptor is labeled the wrong way round.)
The only other connectors (all on the back) are Power Adaptor, Pedal and Earphones.
NathanMac said that the Yamaha PSR500 is relative(ly) unknown, even on the Yamaha site.
However, they do offer some advice on how to connect here:
http://faq.yamaha.com/us/en/article/musical-instruments/keyboards/digitalkeyboar ds/portable_keyboards/psr500/656/1385/Interfacing_a_Yamaha_MIDI_Keyboard_with_a_ Laptop_Computer
I hope this helps.

Seagate Plug and Play from Macbook Pro to Macbook Air

Recently bought a new Macbook Air to upgrade my 2010 Macbook Pro 13 inch.
I had been using a Seagate Plug and Play external hardrive that needed no formatting on my Macbook Pro . However when I tried to use the same on my Macbook Air it did not allow me to drag files across the the hardrive.
I can see it in the Finder but unable to drag files to it.
I thought Plug and Play woudl across all Macs?

OS X comes with the ability to read NTFS but not write it. Some Seagate drives come with software to enable writing NTFS on that drive. You probably installed it on your 2010 MBP when you got the drive, then forgot you had done so. Find the software installer if it is still on the drive and run it on your MBA. (You might have to locate a newer version online.)
Alternatively, you can purchase a version that can run on any NTFS disk. I use Paragon NTFS for Mac. I initially got a limited version with a Seagate drive, then purchased the full version.

I have a Keyrig 49 m-audio and it is not recognize by OS 10.9.4 when it says that mavericks is plug and play. I would really like to do what I am able to do on earlier version of OS... Please help

I have a Keyrig 49 m-audio and it is not recognize by OS 10.9.4 when it says that mavericks is plug and play. I would really like to do what I am able to do on earlier version of OS... Please help

it the link it seem someone made it work. How can a new OS make things more difficult... it seem crazy too me.
via: http://community.m-audio.com/m-audio/topics/m_audio_keystation_with_osx_maverick s_9_1_doesnt_work_via_plug_n_play
pavery85 8 months ago
**UPDATE*** All is working on Mavericks 10.9.1 for me!! Back in business!
Drivers seem to working now!

How to create plug and play design pattern on a environment

Hi All,
Help me to get a best design for my problem statement.
Problem Statement: I have to create a platform where I should be able to plug and play different components. explaining better with example
Example:
1. I have to create a platform for school
2. In this school platform we have to plug in multiple components like "Student", "Teacher", "Subjects", "ClassPeriods" etc.,
3. These components should be easily plug/unplug and play
4. Like, the component "ClassPeriods" want to purchase from Vendor 1 and plug it to "School" platform it should work.
5. Incase if we want to unplug the "ClassPeriod" component provided bfy Vendor 1 from "School" platform and want to plug the "ClassPeriod" from Vendor 2. then the Design should support without any extra effort.
Suggest me the best design pattern for the problem
This design pattern is for ASP.Net
Thanks,
S.Kannan

Sounds like you're looking at 'Composition'. As a background, and possible solution, take a look at MEF;
http://mef.codeplex.com/
http://pauliom.wordpress.com

Is the AC Adaptor Plug and Play?

Similar Messages

Maybe you are looking for