Is the AT-MIO-16DE-10 an E series device?

I'm trying to reinstall labview and I'm not sure which option to select. The choices are the recommended one, the one for all non-E series devices, and neither, and there's a note at the bottom for which devices should use neither.

The AT-MIO-16DE-10 is an E Series device. Thus, I would pick the "recommended one" because that seems to apply to the E Series boards which are the regular boards produced by NI.
If you still have troubles, let me know what version of LV you are trying to reinstall.
L Aguila
Applications Engineer
National Instruments

Similar Messages

  • Looking for Labview Examples for At-MIO-16DE-10 and AMUX-64T

    looking for examples to record:
    Load vs strain and temperature using these two.
    Also a quick guide to how to get started. I hav Labview 6i and the card and board. No experience yet.

    Greetings,
    There are a variety of documents on our website that contain information about using the AMUX-64T with an MIO device. There are also example programs that show how to acquire readings using an MIO device with the AMUX-64T. I have linked to some of better documents below as well as the AT-MIO-16DE-10 and AMUX-64T User Manuals.
    AT E Series User Manual
    http://digital.ni.com/manuals.nsf/webAdvsearch/6FB4341E8E3080F086256BD000550261?OpenDocument&vid=niwc&node=132100_US
    AMUX-64T User Manual
    http://digital.ni.com/manuals.nsf/webAdvsearch/AF2CEB4411E9D3DE862567130055EAAC?OpenDocument&vid=niwc&node=132100_US
    How do I Address an AMUX-64T with an MIO Board?
    http://digital.ni.com/public.nsf/websearch/C6D362737414AD6D862562A80070E694?OpenDocument
    Taki
    ng Thermocouple Measurements Using the AMUX-64T
    http://digital.ni.com/public.nsf/websearch/9D8232DFFE50108F86256DCD005A319B?OpenDocument
    I would start with making sure the AT-MIO-16DE-10 is installed and configured correctly. You can used Measurement and Automation Explorer (MAX), which is software that is installed with NI-DAQ, to configure and test the AT-MIO-16DE-10. The AT-MIO-16DE-10 user manual goes through the installation and configuration steps for the device. Then I would attach the AMUX-64T and try to acquire signals. You can use the AMUX-64T user manual and the other linked documents to help you determine how to acquire signals when the AMUX-64T is connected to the AT-MIO-16DE-10.
    I hope this helps.
    Regards,
    Todd D.
    NI Applications Engineer

  • How to generate a sinewave with at-mio-16de

    I have an at-mio-16de Daq card. I want to generate a sine wave on the analog o/p. I believe that I would use the WFM_load function. I do not understand 1) how to load a buffer for this function and 2) what mode I am supposed to use. The modes in the help file all say the description is for the DAQArb 5411. I am using visual basic for my app.

    There are a number of examples which ship with the NI-DAQ driver which perform an analog output using the WFM commands. If you installed support for Visual C or Visual Basic when you installed the NI-DAQ driver you will find examples in the \Program Files\National Instruments\NI-DAQ\Examples directory. You didn't mention what language you were using; however, if you look in the VisualC\ao subdirectory you will find manu examples which demonstrate generating a waveform from your device. Use these examples in conjunction with the NI-DAQ Function Reference Manual, which can be downloaded from http://www.ni.com/manuals, and you will be able to better understand what is happening in these examples.
    Regards,
    Justin Britten

  • Question about setup_MITE in the PCI-MIO-16E-1

    I have a quick question about setup_MITE in the PCI-MIO-16E-1. In one of the manuals, it states that if you're using Dell Optiplex GX series for our hardware configuration, is it true we need to re-write the MITE functions to correlate with the hardware? Please if you can clarify what this means, I would really appreciate it. Thank you in advance.

    National Instruments is starting a new newsgroup to provide a forum for customers to discuss register level programming issues and ask questions. This newsgroup is not a direct support channel for register level programming, but may be monitored by National Instruments engineers. Please post you question with additional detail in:
    natinst.public.daq.driver-development.general
    Christian
    Christian Loew, CLA
    Principal Systems Engineer, National Instruments
    Please tip your answer providers with kudos.
    Any attached Code is provided As Is. It has not been tested or validated as a product, for use in a deployed application or system,
    or for use in hazardous environments. You assume all risks for use of the Code and use of the Code is subject
    to the Sample Code License Terms which can be found at: http://ni.com/samplecodelicense

  • I want the PCI-MIO-16-E4 ad board driver file.

    I am  doing research in aerospace department Anna university. i am using the hotwire annemometer. Data acquisition  purpose using the PCI-MIO-16-E4 AD board. The driver file of the board is corrupted. so request you to send the driver file.
    thank you  

    Hi!
       The board you're using is quite old, check for NI PCI-6040E (which is said to be "formerly known as PCI-MIO-16E-4").  So you should search for that drivers, the one for PCI 6040.  See the attached links:
       PCI 6040E
       traditional DAQ
       devices supported by traditional DAQ
       This board is supported also by Ni-DAQmx, which is a newer set of drivers. Check for LV and OS compatibility....
       But... just a question, how do you say that driver is corrupted? Do you have a message from LV, or whatelse?
       Hope I can help...
    graziano
    PS.: Just a note, post these kind of requirement under Data aquisition, or DAQ forums, there you can find exactly what you need!

  • Can the AT-MIO-16E-1 output a given current ?

    i was just wondering if i am able to output a specified current level by using the analog outputs, with my DAQ

    The analog outputs on the AT-MIO-16E-1 are setup for voltage, but you could set generate a related current with external circuitry. This is not a trivial task. If you need to source current, I would recommend using the NI-6704 or a signal conditioning solution. More details about the 6704 board can be found at:
    http://sine.ni.com/apps/we/nioc.vp?lang=US&pc=mn&cid=1100
    The signal conditioning solution I would recommend would be the 5B39. More details about the 5B modules can be found at:
    http://sine.ni.com/apps/we/nioc.vp?lang=US&pc=mn&cid=3246

  • I need a user manual and/or spec for the AT-MIO-16H-9 Daq board

    I am interested in the precision for different input ranges for analog voltage measurment
    Thanks

    Go to ni.com and search on "at mio 16" (no dashes). You will find an entry for the AT-MIO-16 User Manual. It has your information.
    Regards,
    Doug

  • Is the AT-MIO-16E-2 ISA card compatible with a Pentium III 1GHz with a 133MHz bus?

    Is the AT-MIO-16E-2 ISA card compatible with a Pentium III 1GHz with a 133MHz bus? The system has an ISA slot available but I'm afraid the bus speed is too fast for this old card. Do I need to buy a new PCI card to work in this system?

    Hello;
    As long as your machine has a ISA slot and that the NI-DAQ driver is properly installed on it, you shouldn't have any problems with it.
    Regards
    Filipe A.
    Applications Engineer
    National Instruments

  • I lost my iphone 4, but I found it using the find my iphone app on another apple device. But before I did this I erased all the data from my phone. When I try to reactivate it I am asked to unlock my sim but there is nowhere for me to enter the pin.

    I lost my Iphone 4, but I was able to find it using the find my Iphone app on another apple device. However, when I try to actiavte it, I am asked to enter a PIN to unlock my SIM. But, I don't know where to enter the PIN. Please help me. Thankyou.

    Contact your cell provider.

  • HT1926 What do I do with the error..."Service 'Apple Mobile Device' (Apple Mobile Device) failed to start.  Verify that you have sufficient privileges to start system services."  This is on my Window desktop.  Removed/reinstall still get this. Help? Retri

    I was getting an update and it would not load so I tried to uninstall and reinstall.  Now when it reinstalls it gets to the end and it comes up with the following error message.
    Service 'Apple Mobile Device' (Apple Mobile Device) failed to start. Verify that you have sufficient privileges to start system services.
    This is on my desktop that I have had for a number of years that has had itunes for a number of years.  I have an two ipods and an ipad associated with the itunes account.  Now I can not get it to go past this message.

    Go to Control Panel > Add or Remove Programs (Win XP) or Programs and Features (later)
    Remove all of these items in the following order:
    iTunes
    Apple Software Update
    Apple Mobile Device Support (if this won't uninstall move on to the next item)
    Bonjour
    Apple Application Support
    Reboot, download iTunes, then reinstall, either using an account with administrative rights, or right-clicking the downloaded installer and selecting Run as Administrator.
    The uninstall and reinstall process will preserve your iTunes library and settings, but ideally you would back up the library and your other important personal documents and data on a regular basis. See this user tip for a suggested technique.
    Please note:
    Some users may need to follow all the steps in whichever of the following support documents applies to their system. These include some additional manual file and folder deletions not mentioned above.
    HT1925: Removing and Reinstalling iTunes for Windows XP
    HT1923: Removing and reinstalling iTunes for Windows Vista, Windows 7, or Windows 8
    tt2

  • HT1923 I'm trying to re-install itunes on my laptop & I am getting a message that has stopped the re-install & it says: "Service 'Apple Mobile Device" (Apple Mobile Device) failed to start. Verify that you have sufficient privileges to start system servic

    I'm trying to re-install itunes on my laptop & I am getting a message that has stopped the re-install & it says: "Service 'Apple Mobile Device" (Apple Mobile Device) failed to start. Verify that you have sufficient privileges to start system services."  The diaglogue box gives me the options to abort, retry, or ignore; when I tried retry and ignore the re-install process stays stalled & the dialogue box comes back & I don't want to abort & start this all over to probably end up with the same issue; what does this mean & what do I do?

    Go to Control Panel > Add or Remove Programs (Win XP) or Programs and Features (later)
    Remove all of these items in the following order:
    iTunes
    Apple Software Update
    Apple Mobile Device Support (if this won't uninstall move on to the next item)
    Bonjour
    Apple Application Support
    Reboot, download iTunes, then reinstall, either using an account with administrative rights, or right-clicking the downloaded installer and selecting Run as Administrator.
    The uninstall and reinstall process will preserve your iTunes library and settings, but ideally you would back up the library and your other important personal documents and data on a regular basis. See this user tip for a suggested technique.
    Please note:
    Some users may need to follow all the steps in whichever of the following support documents applies to their system. These include some additional manual file and folder deletions not mentioned above.
    HT1925: Removing and Reinstalling iTunes for Windows XP
    HT1923: Removing and reinstalling iTunes for Windows Vista, Windows 7, or Windows 8
    tt2

  • Pages crashes when opening any document on iPad 3 Latest version.   I could find on the net and finally deleted Pages from my device and reinstalled it. Still when I try to create anew document or open a document it just cr

    Pages crashes when opening any document on iPad 3 Latest version. I tried everything I could find on the net and finally deleted Pages from my device and reinstalled it. Still when I try to create a new document or open a document it just crashes out.

    Try this:
    Make sure IOS is updated to latest version
    Reboot device by pressing both the home button and sleep/wake (power) buttons at the same time for 10-15 seconds until the apple logo appears on the screen, then let go.
    If that doesn't work then reset the device by going to settings/general/reset/reset all settings

  • I don't have a wireless printer, and want to print things off of my iPad.  I know that I can use the iPad Camera Connection kit to connect USB devices like keyboards and I am wondering if I could do the same with a USB printer.

    I don't have a wireless printer, and want to print things off of my iPad.  I know that I can use the iPad Camera Connection kit to connect USB devices like keyboards and I am wondering if I could do the same with a USB printer.

    I don't think you can connect a printer since you won't have the printer drivers. I use FingerPrint from collobos.com to print to my non-AirPrint printers.

  • Please help i am going off my mind when i connect my iphone 4 to my mac it tells me it can not be used because it requires 10.6.3 or later my mac is operating on 10.6.8 and my itunes is 10 .5 yet the iphone does not even show up in devices please help

    please help i am going off my mind since i updated my iphone 4 when i go to sync it tells me it can not be used as it requires 10.6.3 or higher
    my mac is running on 10.6.8 and i upgraded my itunes to 10.5 everything seems to be in place but the phone is not even being recognised in
    devices although it does come up in iphoto if anybody can help i would be very grateful.

    You have answered your own question:
    "requires 10.6.3 or higher"
    " i upgraded my itunes to 10.5 "
    You need itunes 10.6.3 or later.

  • I have the newest version of the iPad and can not see it under devices in my iTunes account on my PC.  I can however see my iPod touch under devices and sync it.  How can I get my iPad to show under devices and sync as well?

    I have the newest version of the iPad and can not see it under devices in my iTunes account on my PC.  I can however see my iPod touch under devices and sync it.  How can I get my iPad to show under devices and sync as well?  I have also tried may suggestions on the apple support site and none have worked.  Any suggestions are welcome.

    You need iTunes version 11+.
    iPad not appearing in iTunes
    http://www.apple.com/support/ipad/assistant/itunes/
    iOS: Device not recognized in iTunes for Mac OS X
    http://support.apple.com/kb/TS1591
    iOS: Device not recognized in iTunes for Windows
    http://support.apple.com/kb/TS1538
    How to restart the Apple Mobile Device Service (AMDS) on Windows
    http://support.apple.com/kb/TS1567
    IOS: Syncing with iTunes
    http://support.apple.com/kb/HT1386
    Apple - Support - iPad - Syncing
    http://www.apple.com/support/ipad/syncing/
     Cheers, Tom

Maybe you are looking for