Is the Keithley 2612A compatible with Labview 7.1?

Hi,
I've got a shiny new Keithley 2612A dual channel sourcemeter and would like to start using it our lab's system. We are currently using LabView 7.1.
I found a driver for the 2612A, but it says it's only compatible with LabView 8 or higher:
http://www.keithley.com/base_download?dassetid=51950
Does anyone know of another driver, or other method that I might get this thing working in LabView 7.1?
Many thanks,
John
Solved!
Go to Solution.

Download it and post it to the Downconvert thread.
edit - It's a project style driver which was introduced with LabVIEW 8. It might take a little longer.

Similar Messages

Is the cRIO 9067 compatible with LabVIEW 2013?

I just purchased 2 cRIO 9067s and I'm trying to configure one of them to use. I got the IP address set and booted it into safe mode. The status light blinks twice, then pauses. The documention says this means I need to download software. NI MAX only suggests using versions 14.?, which I'm assuming is LabVIEW 2014, but that option is grayed out. And if I try to do a custom install, everything in the list produces a concfict and wont download. Is the 9067 only compatible with LV 2014? Or am I missing a step? the version of LV that I am using is 2013. I'm installing 2014 to test this theory, but I'm no thopeful. Thanks for the help people.
Solved!
Go to Solution.

The cRIO-9067 does require LabVIEW and NI-RIO 2014. You can use http://download.ni.com/pub/gdc/tut/crio_software_versions.htm to look up the minimum software support for cRIO products.
I don't see how I can link directly to the result, but if you select "CompactRIO Chassis and Controllers" from the drop down and then "cRIO-9067" you should see this table.
NI cRIO-9067
Minimum Software Support
Software
CompactRIO (FPGA Interface)
CompactRIO (Scan Interface)
✔ Supported
✔ Supported
LabVIEW
2014
2014
LabVIEW FPGA Module
2014
LabVIEW Real-Time Module
2014
2014
Device Driver Software
NI-RIO Device Drivers August 2014
NI-RIO Device Drivers August 2014
NI-DAQmx
Other Minimum Software

Speeding the Keithley 6485 readings with LabView

Hi All,
I'm new with LabView and with current measurements. I'm using a Keithley 6485 Pico-Amp to recored the current changes in microchannels. I downloaded the instrument drivers from the NI website and I tried to control the Pico-Amp current readings with LabView 7.1 but the rate of readings from the Pico Amp was slow ( a reading every 0.5 s). I tried to change a lot of parameters and I found the main problem causing such slow measurements is the read VI for the Pico-Amp was very slow in the while loop.
is there any way to recored fast continuous measurements from the Pico-Amp using the read VI in a while loop with LabView 7.1?. or if there is another to do fast recordings form the Pico-Amp with LabView?
I appreciate your help and suggestions.
thanks

thanks a lot guys for your suggestions and comments.
at the present time I'm using the analog output of the Pico -Amp to recored the readings via a Daq since I couldn't control it form the drivers. So, I only control the Pico Amp from the front panel.
Dennis, thanks for your suggestions and it is true that fetch multi-point is faster but it is still not fast enough since I want reading at a rate of 40-50 Hz. if you know of a way to increase the readings rate to the frequency I need it will be helpful.
F. Schubert, thanks for comments. I don't know how to change the NPLC since when I change the value in the VI an error message appears and Labview terminates. the NPLC setting is 1 and PLC 60 Hz.
I attached a sample of VI I'm using to find the readings from the Pico-Amp and I would appreciate any suggestions to improve the readings rate. also how can I change the NPLC value of the device?
Thanks
Message Edited by Zeyad on 09-13-2007 11:51 AM
Attachments:
Pico_AMP_tests_2.vi ‏125 KB

In need of a KEITHLEY 2001 single read .vi that is compatible with LabVIEW 7

I am updating from LabVIEW 5.1.1 to 7. The KEITHLEY 2001 Single Read .vi has coercion errors, and does not function. Where can I get updated KEITHLEY 2001 .vi's that are compatible with LabVIEW 7?

You can visit http://ni.com/idnet/, click the "Search Drivers" button
and select "Keithley" as the manufacturer and hit the "Go" button.
Look down the list, and you'll find the LabVIEW Certified Plug and
Play driver for this multimeter scanner.
I hope this helps.
Brian

Is the Intel I340-T4 Ethernet card compatible with LabView 8.6?

We are currently looking in to having our LabView program process the output of two Allied Vision cameras, run through a PCI GigE card.
On our old machine (32-bit Vista), we have a PRO/1000 PT Quad working just fine with the LabView interface - and we want to upgrade to a better PC with 64-bit Win 7.
We are under the impression that PRO/1000 PT is not compatible with Win 7, and were looking into either I340 quad-port adapters:
http://ark.intel.com/products/49186/Intel-Ethernet-Server-Adapter-I340-T4
Does anyone have any insight as to the compatibilities of the Intel 82580 controllers with LabView 8.6?

Hi Civa,
Scott here from AVT technical support. You are correct re. that PT card not being Win7 compatible. Here's a link to our current recommendations for NICs and switches.
http://www.alliedvisiontec.com/fileadmin/content/PDF/Support/Application_Notes/Hardware_Selection_fo...
If it's NOT in that list, it doesn't mean it won't work, merely that we haven't tested it and do not know. We do not attempt to test every 3rd party product on the market.
And our testing is typical with AVT SDKs not with Labview, though there are thousands of joint AVT / NI customers, and we'd have heard by now if there were any conflicts, I am confident.
Regards,
Scott

How can I use my Keithley 2100 DMM with LabVIEW 7 Express?

How can I communicate with Keithley 2100 digital multimeter using LabVIEW 7.0?

Hi,
There are a number of ways,
1) Unfortunately the driver on the Keithley site is for labview version 8.0, so you could speak to keithley to see if they can provide a ver7.0 of the instrument driver
2) You could use the version for the 2000 model from the NI website
http://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=E3B19B3E90B0659CE034080020E748...
There is a version 7.0 which you could modify to suit the 2100
3) Use the VISA vi's and create your own driver using the user manual for the bus commands to driver the instrument.
Hope this helps
Regards
Ray Farmer
Regards
Ray Farmer

Are USB-6008 drivers available that make it compatible with LabVIEW 6.1?

I'm using a USB-6008 Multifunction DAQ, but it is not compatable with teh version of LabVIEW I'm using, 6.1. I may be able to upgrade to LabVIEW 7.1 to solve the problem, but I wanted to know what alternatives I have. Are there any available drivers or patches that allow the USB-6008 to be recognized by LabVIEW 6.1?

Unfortunately, no. The driver for the USB-6008, DAQmx Base 1.5 is only compatible with LabVIEW 7.0 or newer.
-Alan A.

Is the DAQ Assistant compatible with LabView7?

I am equipped with LabView7 and a NI DAQ-Pad 6015 and am trying to monitor temperature using two thermocouples. I have searched for some tutorials online but most suggest using DAQ assistant, which is not listed in the input section of my functions palette. I have downloaded the most recent NI-DAQmx driver which is supposed to be compatible with LabView 7.x. I'm not sure if this means that it is compatible with LabView 7.0. I still do not see the DAQ assistant appear.
Any help or suggestions (about DAQ assistant or how to program in LabView7 to solve my problem) is greatly appreciated!
Thanks.
Solved!
Go to Solution.

I have installed DAQmx 8.1 and now the DAQ assistance appears. However, when I select Analog Input >> Temperature >> Thermocouple and arrive at the physical channels screen, it says "No supported devices found."
I also notice that when I open the Measurement & Automation explorer, it does not appear to detect my DAQ pad, even though the light on it is blinking Ready. A window pops up and says "Can not find RTE directory: C:\Windows\system32\cvirte" followed by "Unable to open c:\program files\national instruments\max\bin\cvirte.rsc". After clicking okay to both windows, I check under Devices and Interfaces to see that my DAQpad 6015 is not listed.
Previously before I had uninstalled everything and reinstalled using DAQmx 8.1 my device was detected, but now it doesn't seem to be detected anymore.
Also, I just realized that while it says everywhere that I have LabView7, when I start the program, the opening window has LabView7 Express written on it. I hope this isn't the cause of all the troubles.
Message Edited by Particle42 on 05-28-2009 03:19 PM

Keithley 2750 interfacing with LabVIEW 8.5?

This is my first time trying to set up the two software and hardware. The Keithley 2750 was originally installed and taking data using ExceLink. Now, I want to use LabVIEW instead for data acqusition. I have already installed the LabVIEW cds.
Where do I start to set up the interface between the Keithley 2750 multimeter and LabVIEW 8.5?

If the title says Agilent, then you have opened the wrong example. Exactly which driver did you download? Project style plug and play or just the plain plug and play? Where did you install it? With either, you should have a folder under your instr.lib called ke27xx. What is in that folder will depend on the type of driver you downloaded. The project style (recomended), will have a .lvlib and .lvproj files and folders called Examples, Private, and Public. If you don't have these, what do you have? Post an image of the directory structure.
Message Edited by Dennis Knutson on 06-23-2008 10:08 AM

I need a step motor and controller compatible with LabView Can you recommend any

I need a step motor compatible with LabView and I thought i would check with you before i moved forward in my experiment

Dear chapbs,
I've attached a sample cart below to show you the components for a possible setup of your system. Keep in mind that whatever stepper drive you purchased would power your motor. If you go ahead with the purchase of a controller & drive, I would highly recommend contacting NI to insure that you purchased the correct accessory components and cables to connect & power the components. I hope the sample cart is helpful. I created it by browsing ni.com, adding items to my cart, and then saving the cart to an excel file. Please post back if you have additional questions.
Best Regards,
~NH
Attachments:
SampleCart.pdf ‏145 KB

Is IMAQ 2.6 fully compatible with Labview 6i?

Hello...does anybody knows if NI IMAQ is fully compatible with ALbview 6i?
What i´m trying to do is to convert a bmp or jpg image to a 2d array..i can do this with the vi ColorImageToArray but how can i get an array for each color plane without using IMAQ Vision module?
Is there a way to convert the 2D 32 bits array that gives the ColorImageToArray into three different color planes or arrays?..is it possible to do this without Vision?
thanks
thanks

Hello,
NI-IMAQ version 2.6 is fully compatible with LabVIEW 6.x. NI-IMAQ driver is an image acquisition driver and it has all the functionality required for acquiring images from an external video source through National Instruments frame grabbers.
In order to do image processing, such as performing operations on saved images from the hard drive, you will need IMAQ Vision image processing libraries.
Hope this helps!
Best regards,
Yusuf C.
Applications Engineering
National Instruments

When IMAQ vision that is compatible with labview 8.0 is going to be released?

Hi, i got labview 8.0 but it is not compatible with imaq vision 7.x series. I am wondering when the new version of IMAQ vision that will be compatible with labview 8.0 is going to be released.
Thank you,
Christos

Hey Matt,
There is also a great knowledgebase document called How do I install my IMAQ software/drivers with LabVIEW 8?, which has an update on it that takes care of moving everything that you need to move in order to get Vision 7.x.x to work with LabVIEW 8.0. Of course nothing extra has to be done with the IMAQ Vision 8.0 software to work with LabVIEW 8.0. One more thing, similarily to LabVIEW 8.0, you can now download the Vision Development Module Version 8.0 software from NI's website in case you wanted to try out (30-day trial) the Vision 8.0 software before upgrading.
I hope this helps. Have a great day.
Regards,
DJ L.

Is Max 4.1 compatible with Labview 7.0?

I see that Max 4.1 comes with daqmx 8.3 which is NOT listed as Labview 7.0 compatible. I also see that installing the last daqmx for labview 7.0 (ie daqmx 8.1) would install max 4.0.3. Therefore, if i have max 4.1 installed with labview 7.0/daqmx8.1 am I expected to have issues?

degenste,
Just to clarify a bit, Measurement and Automation Explorer (MAX) displays a list of NI devices and software on your computer, but it does not install support for those devices. The DAQmx driver is responsible for installing support for our Data Acquisition products. Support for USB M-Series devices was not added until version 8.3 of DAQmx. This knowledge base article describes why the USB M-Series product line has to be used with DAQmx 8.3.
You are correct when saying that DAQmx 8.3 is not compatible with LabVIEW 7.0 as stated in this document. With this set up, your only options would be to upgrade your LabVIEW version or choose a different form factor such as PCI for your device.
Regards,
Ryan N
National Instruments
Application Engineer
Ryan N
National Instruments
Application Engineer
ni.com/support

Got the message "not compatible with this signal" on TV when connecting ATV to HD TV.

I got the message "not compatible with this signal" on TV when connecting Apple TV to my Sharp HD TV.

Go into safe mode an uninstall this new game.
If this doesn't work, uninstall the graphics driver so Win will install it again after restart.
HTH
V.
*** Say 'Thanks' with Kudos ***

Which is the MYSQL version compatible with SAP PI 7.0

Dear friends,
can any body tell me which is the MYSQL version compatible with SAP PI 7.0, i m getting the below error , some body told me, may be the MYSQL version is not compatible with PI 7.0
Message processing failed. Cause: com.sap.aii.af.ra.ms.api.RecoverableException: Error when attempting to get processing resources: com.sap.aii.af.service.util.concurrent.ResourcePoolException: Unable to create new pooled resource: DriverManagerException: Cannot establish connection to URL 'jdbc:mysql://192.168.51.50:3306/stagingdb': SAPClassNotFoundException: com.mysql.jdbc.Driver
rgds
mojib

Hi
if the interface was running fine and suddenly stop working ...and as per the error log u have pasted here ....99% chances are due to connection problem ...check whether TCP/IP connection for port 1433 is working finr or not ,,....do Xi system is able to make the telnet from SQL server or not...may be any firewall get enable ..........
just check with this blog also .....same thing happensa with me once also fora client .....
(/people/charu.agarwal/blog/2009/07/02/problems-faced-while-connecting-to-sql-server-using-jdbc-adapter-in-pi)
Regards
Abhishek

Is the Keithley 2612A compatible with Labview 7.1?

Similar Messages

Maybe you are looking for