Is the PXIe-5622 digitizer really unsupported by the LabView Real-Time OS?

Hello,
  We need to sample a 60 MHz signal with 15 MHz of bandwidth, for durations of up to eight hours, and were considering the PXIe-5622 board.  Given the high PRF we need (6.4 kHz), we want a Real Time OS deployment. However, it seems that this board (and none of the other RF boards) are not supported by the RT Embedded Controller, but require the dreaded Windows for control.  Is this actually true?
Cheers. 

Hey smudog,
The PXIe-5622 is actually supported on real-time. The NI-SCOPE driver picked up support for RT with version 3.5 and the NI-RFSA driver picked up support with version 2.08 (latest version is 2.1). I attached links to the drivers and you can click the link to the readme's to see confirmation.
NI-SCOPE 3.5 - Windows 2000/Vista x64/Vista x86/XP
http://joule.ni.com/nidu/cds/view/p/id/1096/lang/en
NI-RFSA 2.1 - Windows 2000/Vista x64/Vista x86/XP
http://joule.ni.com/nidu/cds/view/p/id/1100/lang/en
Regards,
Chris Delvizis
National Instruments

Similar Messages

  • Does the LV F3 Patch cover the LV Real Time f2 patch?

    Does the  LV 2009 f3 patch patch also include the fixes from LVRT2009f2Patch ? (I'm assuming the two f2 patches are different)
    The following is from the download page for the LV 2009 f3:
    "The LabVIEW 2009 f3 patch includes all of the fixes of the LabVIEW 2009 f2 patch."

    Hi jjsutc,
    You are correct that the two f2 patches are different. The LabVIEW 2009 f3 Patch does not include the fixes from the LabVIEW Real-Time 2009 f2 Patch.
    Thank you for choosing National Instruments.
    Aaron P
    National Instruments
    Applications Engineer
    http://www.ni.com/support 

  • Could I use two regular computer to achieve realtime communicat​ion using the Ethercat and Labview Real Time Module?

    Could I use two regular computers (one acts master , another one acts as slave using the Ethercat Internet Card) to achieve realtime communication using the Ethercat and Labview Real Time Module? if it could, what hardware should I purchase from the NI ?
    Thank you!

    Hi Xiaolin,
    NI doesn't offer Windows based Ethercat master or slave software. Only LabVIEW RT can run the Ethercat driver. 
    However, you could use a LabVIEW RT target as an Ethercat master and use the Ethercat Internet Card with a slave PC (note: I think this will work from the Beckhoff description of the card you are describing. The card should integrate like any other non-NI slave. However I haven't tested the setup and don't advise saying it will work until you have tried). 
    You can use any NI RT target with two ethernet ports as the Ethercat master. This could be a cRIO, PXI or RT Desktop. 
    Jesse Dennis
    Design Engineer
    Erdos Miller

  • How to change the default Real-Time Collaboration page?

    Who can tell me how to change the default Real-Time Collaboration page?
    If I want to add my corporation logo in the top of the default page.How to do?
    Thanks!

    Thanks for your help.
    "Click the Sites tab to display all sites and their IDs for your system." But I clicked the sites tab ,it showed "http://hostname:7777/imtapp/app/home.uix". I could not find the siteID parameter from it. Why?
    How to get it from command?

  • UNABLE TO LOCATE THE THE LABVIEW RUN-TIME ENGINE.LVBROKERAUX71

    UNABLE TO LOCATE THE THE LABVIEW RUN-TIME ENGINE.LVBROKERAUX71 REQUIRES A VERSION 7.1 (OR COMPATIBLE) LABVIEW RUN-TIME ENGINE。PLEASE CONTACT THE VENDOR OF LVBROKERAUX71 TO CORRECT THIS PROBLEM
    Uninstalled DAQ and reinstalled.  MAX still throws an error. 
    Any Isead besides uninstalling 3/4 of my software?
    Merry Christmas!
    Matthew Fitzsimons
    Certified LabVIEW Architect
    LabVIEW 6.1 ... 2013, LVOOP, GOOP, TestStand, DAQ, and Vison

    To clean up your system, you will need to uninstall the LabVIEW 7.1 run-time engine, and the "LVBroker," and the "LVBrokerAux71" components using the MSI Blast utility.  To obtain this utility, please create a service request for phone or e-mail support, and contact one of our Applications Engineers about this issue.  Thank you!

  • Unable to locate the LabVIEW Run-Time engine

    Using LabVIEW 2011, I have built an executable and installer including the LabVIEW Run-Time engine. I built the app on a 32-bit system. I'm deploying it to a Windows7 64-bit system. When I ran the installer, rebooted, then tried to run the app, I got an error messsage stating "Unable to locate LabVIEW Run-Time Engine", stating that the LVRTE 2011 was needed to run the app, and asking if I want to download from NI. I have tried downloading the RTE and re-installing it, but when I try, I get an error message from the installer stating that there is a newer version of the RTE already installed, and the installer exits! I have tried un-installing the application, but have had no luck removing the RTE. Now I'm stuck. The re-installed executable application says it can't find the RTE, and the RTE installer says there's a later version already installed!
    I can't go forward or backwards!
    Prior to running the installer for this app, I had a working LVRTE for 2011, and was running some other executable LabVIEW programs on the target box. However, since this new application had additional components not included in the original install of the RTE, I built the new installer which included the additional components. Once I ran that installer, my problems began.
    In my frustration, I've tried downloading from NI both the 32 and 64-bit versions of the RTE, and installing them. I realize that the app was built on a 32-bit system, so the 32-bit RTE SHOULD have run it fine, but didn't.
    At this point I have removed the 64-bit RTE using the NIUninstaller. I believe I need to completely remove all 32-bit RTE components and start over, but I have not been able to. The 32-bit RTE does not show up in any un-install utilities I've found.
    What could be causing this problem, and how do I get past it??
    Thank you.

    One thing I did discover in my struggles is that the RunTime engine on the target box needs to be based on the environment of the development box. So if you built the app on a 32-bit machine, you would need to install the 32-bit RTE, even on your 64-bit target box.
    The RTE Uninstaller might not show up in the Windows Add/Remove Programs utility. In my case the 64-bit RTE uninstaller showed up, but the 32-bit did not. The NiUninstaller (C:\Program Files\National Instruments\Shared\NIUninstaller) did list both RTEs for uninstalling, but still didn't get me past the problem.
    I was finally only able to get past the problem by doing a system restore to a point in time prior to my changing of the RTE.
    Good luck.
    Dan

  • Teststand error states that a vi failed to load in the Labview Run-Time Engine

    I am getting an error in teststand that states that a vi failed to load in the Labview Run-Time Engine version '14.0.1'
    If I look at the software loaded on my system with the NI Measurement and Automation Explorer I have Labview Run Time engines for version 2009, 2010, 2011, 2012, 2013, & 2014 on my system.
    How do I get this VI to run on this system when it is called by test Stand?
    Thank you

    The RTE 14.0 was loaded as part of my deployment and after I ran this I got an update notice for the F1 patch which I also loaded.
    I do not have labview loaded on this system, only the run time engines from running my deployment.
    When I launch t he teststand sequence, when it calls the labview VI, I get the following error moessage:
    Error: Failed to load VI 'C:\builds\RelayVoltageMeaure.vi' in the LabVIEW Run-Time Engine version '14.0.1'. LabVIEW: The VI is not executable. This error may occur because the VI is either broken or contains a subVI that LabVIEW cannot locate. Select File>>Open to open the VI and verify that you can run it. VI Path: C:\builds\RelayVoltageMeaure.vi[Error Code: -17600, Failed to load a required step's associated module. ]
    I have attached the teststand sequence if this helps.
    Thanks
    Attachments:
    QuantumDigitalBd.seq ‏13 KB

  • System Error 998 While loading the Labview Run-Time Engine

    Hello.
    I have a DLL made with LV 7.1 I run the dll using a C compiler and works great in WINXP, but cannot run in Win2K. Error is:
    "System error 998 while loading the Labview Run-Time Engin(c:\program
    files\National Instruments\Shared\Labview Run-Time\7.1\\lvrt.dll)
    READVOLTAGE requires a version 7.1 (or compatible) Labview Runtime
    Engine. Please contact the vendor of READVOLTAGE to correct this
    problem"
    READVOLTAGE is my function inside the dll. The runtime is already
    installed. I tried it in another WINXP running machine and works fine.

    This is actually a Microsoft bug with statically loaded DLLs. There are a couple of workarounds for it, and I have included two links below to posts that address this issue:
    Not found error message from LabVIEW runtime when called from VC++ with statically linked MFC
    I get error 998 when calling a LabVIEW buildt DLL from MSVC++
    Kind Regards,
    E. Sulzer
    Applications Engineer
    National Instruments

  • Can I run two separate versions of the LabVIEW Run-Time Engine on one PC?

    Hello, I am curious if anyone knew if it is possibly to install and use two separate versions of the LabVIEW Run-Time Engine on one PC?  I currently have the 2009 Run-Time Engine installed on one machine and wanted to install the 2011 Run-Time Engine as well. I know that you can run two separate versions of the LabVIEW program on one machine, but what about the Run-Time Engine?
    Thanks!
    Solved!
    Go to Solution.

    I'm guessing this is a bug that NI needs to fix.  I see no reason you shouldn't be able to install the run-time engine of an older version.  I'd be interesed in if it allows you to install the older development environment, which also includes the older run-time engine.  There are some command line switches for NI installers as mentioned here:
    http://digital.ni.com/public.nsf/allkb/C361087EE9F20810862577850073128E
    I wonder if there is a force install option.
    Unofficial Forum Rules and Guidelines - Hooovahh - LabVIEW Overlord
    If 10 out of 10 experts in any field say something is bad, you should probably take their opinion seriously.

  • System error 988 whlie loading the LabView eun-time engine (C:\Program file\....\\lvrt.dll)

    I am trying to use NI devices with Lazarus (there is no pascal section, so I post here).
    When I try to run my application:
    DAQmxBaseCreateTask('TaskHandle', TaskHandle);
    DAQmxBaseCreateAIVoltageChan(taskHandle,'Dev1/ai0','',DAQmx_Val_Cfg_Default,-10.0,10.0,DAQmx_Val_Volts,'');
    I get the following error message:
    „System error 988 while loading the LabView eun-time engine (C:\Program file\....\\lvrt.dll)
    nidaqmxbaselv requires a version 2010 (or compatible) LabView run-time engine. Please contact the vendor of nidaqmxbaselv to correct this problem.“
    I installed LabView run-time engine 2012, but I still get the same error.
    Then I tried to install LabView run-time engine 2010- the same result.
    I removed LabView run-time engine 2012- same result.
    I tried to install LabView run-time engine 2010 again (since I did not see it in the add/remove list)- then I noticed, that the installer shows „A newer version is already installed".
    What shall I do?

    Hi,
       Can I ask the same question too?
       I am using
       Windows 7 sp1 x64
       Visual Studio 2010 pro 
       NI USB-6009  
       ni-daqmx base 3.4.5 
       I created a empty win-32 console project and putted the ANSI C Example program: acquireNScans.c with the include file and lib file of nidaqmxbase in the same folder. I added this line on the top of the source code #pragma comment(lib,"nidaqmxbase.lib"), built without any error. When I tried to run it, I got this same message.
      I tried changing to shared dll mfc and delaying linking lvrt.dll, but did not work.
      Looking forward to your reply.
    all the best.

  • System error 999 while loading the Labview Run-Time Engin

    Bonjour à tous,
    J’ai un PC avec un Runtime LV71.1 qui me retourne l’erreur suivante. Je ne trouve pas d’info sur cette erreur. Une Idée sur la cause ?
    System error 999 while loading the Labview Run-Time Engin(c:\program files\National Instruments\Shared\Labview Run-Time\7.1\\lvrt.dll)
    Luc Desruelle | Voir mon profil | LabVIEW Code & blog
    Co-auteur livre LabVIEW : Programmation et applications
    CLA : Certified LabVIEW Architect / Certifié Architecte LabVIEW
    CLD : Certified LabVIEW Developer / Certifié Développeur LabVIEW
    Résolu !
    Accéder à la solution.

    Bonjour Maxime, merci pour ta réponse qui est très intéressante. Le soft est en LV7.1.1 est fonctionne depuis plusieurs années. Le PC est chez un client, dans un pays très « hostile », je n’ai donc pas accès à ce dernier. Un superviseur local m’a fait le retour qu’après redémarrage du PC ce dernier indiquait un problème, avec photo pour descriptif. Je n’ai pas plus d’info pour le moment. Je viens donc de demander un CHKDSK c: /F
    Luc Desruelle | Voir mon profil | LabVIEW Code & blog
    Co-auteur livre LabVIEW : Programmation et applications
    CLA : Certified LabVIEW Architect / Certifié Architecte LabVIEW
    CLD : Certified LabVIEW Developer / Certifié Développeur LabVIEW

  • Can anyone provide me the suitable material for labview fpga &labview real time??

    Message Edited by Sithu on 05-27-2008 04:32 AM

    The following link includes training material for both LabVIEW Real-time and LabVIEW FPGA.
    http://zone.ni.com/devzone/cda/tut/p/id/6929
    If you are new to LabVIEW you should start from the LabVIEW Basics material available at the following link.
    http://cnx.org/content/col10241/latest/
    KostasB
    NIUK Applications Engineering

  • Seeks the LabVIEW part time job ,Beijing China (6 years exp)

    Seeks the LabVIEW part time job, if appropriate knocks, it can change to full-time job. The following is the simple introduction,I hoped it can help you to understand me. I had worked for more than 5 years in the China Aerospace Science & Industry Corp. I was engaged in research and development work about the instruments control,Virtual Instrument System Integration,etc.I have finished many projects with LabVIEW. Such as:The Auto Measurement System for People's Liberation Army General Staff Department NO.2. The Time & Frequency Metrology Subsystem of some military project for China Electronics Technology Gropu Corporation 54.(CETC54).The Auto Calibration System for China Aerospace Science & Industry Corp 203 (CASIC203). GPS Rubidium Crystal Oscillator Metrology Auto Measurement System for China Shipbuilding Industry Corporation 750. All of projects have finished the test of army and aerospace. At the same time, I have optimized and improvement the KIT/KPS System for Daya Bay Nuclear Power Operations and Manavement Co.,LtdIn addition, I have finished Auto Measurement Platform for some company. It save 10,000 RMB for the company.I hace finished automatic production line of Fuse for Schneider Electric company.  Tips:  If  the project is very complex and difficult, I can cooperate with my friends. But most projects I can finished by myself.Please contact me, if necessary:Mr.Wang Beijing,ChinaCell Phome:13691203761 Email:[email protected]     [email protected] 

    The appropriate message board for this is LabVIEW Developers Seeking Employment

  • Seeks the LabVIEW part time job ,Beijing China

    Seeks the LabVIEW part time job, if appropriate knocks, it can change to full-time job. The following is the simple introduction,I hoped it can help you to understand me. I had worked for more than 5 years in the China Aerospace Science & Industry Corp. I was engaged in research and development work about the instruments control,Virtual Instrument System Integration,etc.I have finished many projects with LabVIEW. Such as:The Auto Measurement System for People's Liberation Army General Staff Department NO.2. The Time & Frequency Metrology Subsystem of some military project for China Electronics Technology Gropu Corporation 54.(CETC54).The Auto Calibration System for China Aerospace Science & Industry Corp 203 (CASIC203). GPS Rubidium Crystal Oscillator Metrology Auto Measurement System for China Shipbuilding Industry Corporation 750. All of projects have finished the test of army and aerospace. At the same time, I have optimized and improvement the KIT/KPS System for Daya Bay Nuclear Power Operations and Manavement Co.,LtdIn addition, I have finished Auto Measurement Platform for some company. It save 10,000 RMB for the company.I hace finished automatic production line of Fuse for Schneider Electric company.  Tips:  If  the project is very complex and difficult, I can cooperate with my friends. But most projects I can finished by myself.Please contact me, if necessary:Mr.Wang Beijing,ChinaCell Phome:13691203761 Email:[email protected]     [email protected] 

    The appropriate message board for this is LabVIEW Developers Seeking Employment

  • Why do different versions of the LabVIEW Run-Time Engine not compatible?

    LabVIEW Run-Time Engine to become more and more big
    Why do different versions of the LabVIEW Run-Time Engine not compatible?
    " 一天到晚游泳的鱼"
    [email protected]
    我的个人网站:LabVIEW——北方客栈 http://www.labview365.com
    欢迎加入《LabVIEW编程思想》组——http://decibel.ni.com/content/groups/thinking-in-labview
    Solved!
    Go to Solution.

    jwdz wrote:
    LabVIEW2020 ....... ,it look like?
    You need to express your ideas more clearly. We cannot fill in the blanks and read between the lines if the post has no substance.
    jwdz wrote:
    It will affect the future development of LabVIEW, right?
    What is "it"?
    There are many things that affect the future development of LabVIEW, starting with NI management, all the smart people in LabVIEW development, the economy, the LabVIEW users, etc.
    If you are worried about the increasing size of the distribution, the good news is that the cost of data storage and data transmission has dropped much more dramatically. Even though newer versions are bigger due to great and welcome new features, the improvements in infrastructure have actually made the distribution and storage significantly easier over the years and will continue to do so. Trust me!
    Nobody wants to go back to a LabVIEW version that fits on a floppy disk!
    LabVIEW Champion . Do more with less code and in less time .

Maybe you are looking for

  • Scoring question - how do I see more than one instrument's voice at a time?

    I'm trying to compose pieces for different symphony orchestra instruments, but its imossible to toggle back and forth between the matrix view of seperate tracks for arranging the voices of the chords. The only way I can seen the notes in a chord is d

  • No entry in table T551A for key 40 GENR

    Hi Guys, Can anyone please tell me what  is the meaning of this error. "No entry in table T551A for key 40 GENR" I am getting this error while i m trying to set work schedule rule. Thanks Deepali Edited by: DeepaliHCM on Jan 28, 2010 10:27 AM

  • Oracle and Sql Server Physical Schema

    Hi Forumer, I am new to the ODI, and trying to use it for few of the POCs. I know that the ODI supports mulitple types of technologies like Oracle, MS SQL Server, etc. quite well. My requirements are something like this: I have two same application d

  • Debugging BPEL flow from JDeveloper

    Dear all I wonder where I could find some examples of how to debug a BPEL flow using JDeveloper. Any help would be appreciated

  • Change the description of Custom transaction

    Hi All Business requirement is to change the description of custom transaction. I have changed in SE93. But, now this change should appear in all the roles(single and composite) wherever this transaction used. Do I need to update each role or Do we h