Is the Touch compatible with the old radio/remote control?

I was wondering if anyone knew if the new Touch was compatible with the clip-on FM radio/remote control
http://www.superwarehouse.com/AppleiPod_Radio_Remote/MA070GA/p/729855
(it plugs into the dock connector) I would like to be able to control my iPod without taking it out of my pocket. Thanks in advance!

boooooo...!
well, i'm a little disappointed. at least they added the Home Button doubletap feature. I guess I'll just memorize the button layout i've been using a touch-sensitive 3G iPod for 3 years+, so i'm not a stranger to that kind of thing
and wait for a third-party solution
thanks for your help
Message was edited by: Alexander Chan1

Similar Messages

  • Hello, is the itrip compatible with the iphone 4s?

    Hello, is the itrip compatible with the iphone 4s?

    Which one? My friend has a wireless iTrip and it works fine with her 4S.

  • Is the ios8 compatible with the iphone 4s

    Is the ios8 compatible with the iphone 4s

    Compatible?  Well, let's just say that it works. 
    In my case it works well enough for me to keep me from joining the stampede to buy an iPhone 6.  The main reason why I decided to take a chance on the upgrade was for the enhanced security features.
    The big lesson that I learned is to be patient with the installation process.
    When upgrading to IOS8 on a 4S, allow approximately 1-1/2 to 2 hours, even when using a reasonably high-speed connection.  Because the installation takes more than 4GB of storage on the device, you probably will have to temporarily delete podcasts, downloaded iBooks, videos, and larger apps like Numbers, Pages, and Keynote even before you may download the update.
    My total time using a was:
    Making space on my 16GB 4S: 10 minutes (but, to be fair,  a little housecleaning was overdue)
    Download time at approximately 31-33 mbps: <6 minutes
    "Preparing": 50 minutes
    "Installation" ""Verification" and initial restart:  55 minutes
    I have observed a very slight hesitation or slowdown when opening some apps for the first time,  but it is not annoying.  I have not observed any noticeable effect on battery life (which was not that wonderful using IOS7), nor the heat that some people have reported.

  • Is the T440p compatible with the Ultrabay battery?

    Question in title. I want to know if the T440p is compatible with the ultrabay battery. I don't have any use for the optical drive and I know the ultrabay HDD caddy is awful, so i figure I may as well make use of this extra space.
    If not well that's a shame, kind of useless to have such a thick laptop with such a small battery.
    Solved!
    Go to Solution.

    Hello.
    The UltraBay HD caddy works perfectly in mine. Got a 9.5mm 1TB drive in it, and it fits very snugly (I of course added the TP rubber rails to the drive as well), performs like a champ and spins down as configured.
    I also got UltraBay caddies in my T400 and W520, never had an inkling of problem with them.
    ThinkPad W540 (20BG) - i7-4800MQ/24GB // ThinkPad T440s (20AQ) - i7-4600U/12GB
    ThinkPad T440p (20AW) - i7-4800MQ/16GB // ThinkPad Helix (3698-6EU) - i5-3337U/4GB
    ThinkPad W520 (4282-W4Q) - i7-2720QM/32GB // ThinkPad T400 (2767-W1C) - P9500/8GB
    ThinkPad T61 (7665-CTO) - T7700/4GB // ThinkPad T60p (8741-C2G) - T7400/4GB

  • Is the iPhone compatible with the Music Link I have in my 2006 Honda Accord

    I have a 2006 Honda Accord with Music Link so I can play my iPod through the speakers. Is the iPhone compatible with this?

    Welcome to the forums.
    It appears that update 1.1.2 (or perhaps even 1.1.1) "fixed" some issues with the iPhone not working with certain iPod car stereo systems. However, not all seem to be working. As others have suggested, trying it may be the only way to know for sure.
    If you haven't bought it yet and this is one factor then perhaps you could borrow a friend's iPhone to see. However, I wouldn't make this the primary reason to buy an iPhone.

  • Is the latest ipod touch compatible with the 2011 Mitsubishi Lancer Ralliart?

    I recently replaced an older iPod touch with a new iPod touch. The older touch synced with my 2011 mitsubishi lancer. Granted it took the two awhile to communicate but they always synced. I just got the new iPod touch on Feb 3 and tried to sync it with my lancer. It actually syned very quickly and worked perfectly. After I came out of Best Buy to go home, I plugged the touch in again and this time it just said iPod loading..... After about 5 minutes I unhooked the iPod and went back to sirius. Now iPod loading is all I get now....

    Yes, it's compatible.  Try using Disk Utility to reformat the Nano to see if that helps.  Here are instructions on how to reformat your iPod using Disk Utility.
    How to Reformat Your iPod on a Mac
    B-rock

  • Is the ios7 compatible with the ipod touch 5th generation

    does the ipod touch 5th generation get the new ios7?

    About iOS 7
    The following from Apple is all that we know about iOS7 at this time. We are users, too, so we know no more than you.
    iOS 7 will be available as a free software update for iPhone 4 and later, iPad 2 and later, iPad mini and iPod touch (fifth generation) this fall. Some features may not be available on all products.
    *US English, French and German will be available with the launch of iOS 7. Additional languages will be added over time.
    For general information on the features of iOS 7 see: Apple - iOS 7.

  • Is the iPad compatible with the Pioneer Appradio?

    Hi, I've got some questions about using the Appradio system combined with the iPad. Do you know if I can use the Appradio with an iPad, although it isn't officially supported? Could I buy an external GPS (bluetooth) antenna to use them for navigation purposes? (both don't have one) Is it better to change my new iPad for an iPhone? I don't want to. At least, can I use the iPad as a simple iPod, without the apps? Thank you. I've got these items new, so if I try them, I can't give them back.
    Moreover, I found the app in the store, it's iPad-compatible but it appears only in the search results for the iPhone. I don't even know if I could get it...

    I'm going to change the iPad 2 (3G) for the 3rd gen. one and I want to choose the right model. I like the 32GB wi-fi one because I can get the amazing Retina display and enough space for my music with a few coins. I'm going to use the Appradio mainly for music, but if I want to use the navigator I've got to upgrade the iPad with an antenna, which would be better than keeping it on the dash. I can bypass the connection through my phone, this would be quite comfortable too. I'm a student and I haven't got so much money; for the same amount of the upgrade, I could think to buy an old iPhone to replace the iPad when I need the navigator.

  • Is the WRE54G compatible with the WRTP54G ??

    I have a WRTP54G, eg the wireless router that comes with Vonage, and then bought a WRE54G to extend the signal because compatible with WRT54G/GS etc. (I missed the little "P" in the product name...)
    I did the standard installation procedure, but the WRE54G does not work.
    Is there any configuration or special way to install it that could make them work pls? any recommendation welcome!
    THANKS.

    You have WRTP54G wireless router. The default IP address of this router is 192.168.15.1. And you have WRE54G range expander and the default IP address of this range expander is 192.168.1.240. Both the devices are in a different IP address range. Try to configure the Range Expander manually.
    Press and hold the reset button for 30 seconds. Release the reset button. Unplug the power cable from your Expander, wait for 30 seconds and re-connect the power cable.
    1. Connect your Expander to a computer, click on the Start button >>> Settings >>> Control Panel >>> Network Connections - Right click on the icon for Local area connection and go to properties. On the 'General' tab select 'Internet Protocol TCP/IP' and click on the Properties button. Select 'Use the following IP address'- Provide IP Address - 192.168.1.5, Subnet Mask - 255.255.255.0. Click on OK button to Save and Click on "Close" on main Properties window.
    2. Now open an Internet Explorer browser page on your wired computer(desktop). In the address bar type - 192.168.1.240. Leave the User name blank & in Password use admin in lower case. It should open your Expander set-up.
    3. While changing the Expander settings you have to make sure that the Wireless Settings(SSID/Network Name and WEP/WPA Key) are identical on both the devices(Router and Expander).
    Change the Expander's IP Address : 192.168.15.240,Subnet Mask : 255.255.255.0, Default Gateway : 192.168.15.1.
    5. After configuring the Expander you should disconnect it from the Computer and go into Local Area Connection TCP/IP Properties and set it back to Obtain IP Address Automatically. Disconnect the Expander from the computer and power cycle both the devices(Expander and Router) . Your Expander should be configured.

  • Is the C100 compatible with the PIX 240?

    I know the answer should be yes, but I am having trouble with mine.
    When plugged directly into the PIX, I get a "no video" warning and the HDMI menus blink showing imcompatability. But, when I run the HDMI through a simple 5v splitter, the signal locks in immediately.
    I've spoken with Canon a couple of times as well as Sound Devices and I'm not getting anywhere. The C100 feeds a monitor just fine. The Pix records other HDMI inputs without a problem. But the two together just don't work. Has anyone else run into this situation?  I've talked to a couple of other shooters and rental houses and all of their units are compatable and working. I do have the latest firmware on both units. I have run through the menus with both companies. Is there something I am missing? A small setting somewhere that will clear this up?
    To make it worse, I have a colleague who also owns a C100 and his also does not show up on the PIX.  I'm not about to purchase a Ninja as I have the PIX already it it works with everythign else I own. Just wish I could get an answer on why it won't cooperate with the C100.
    All comments welcome. A forwarded solution may result in several comped beverages at NAB in April.

    I've spoken with Canon tech support twice.
    Frame rate is not the issue. 1) The recorder auto detects what is coming in and displays it. Record settings are then made available based upon what is being fed in. 2) The hardware converter in this is pretty good so converting has yet to be a problem.
    But... I cant even get that far.   The signal is not recognized, at all. The recorder just states :No Input  Same as if nothing is plugged in.  When the recorder is plugged in, otput options under the HDMI menu in the camera are no longer available. They blink or grey out. This result has been reproduced with a second C100.
    Yesterday I tested the recorder with 4 different cameras with different resolutions and frame rates. All worked thru the HDMI input to the PIX 240 except the C100. I dont want to be pointing a finger but getting the responce over the phone of, "it not in our unit" is discouraging when its the only one I am having trouble with.
    ~~~~~~~~~~
    I did the test with a colleague present. He is confused as well and asked if there was an OVERRIDE option that would turn off the HDMI communication? That would atleast allow the info to go from the camera out to the recorder with out getting an "imcompatable" signal back in that greys out the menus.
    Any thougths on this?  I have a second PIX unti being lined up to test with that. If I get the same results on that unit it will confirm it is in the camera.

  • HT201343 i have a mid 2010 mac pro and the fact that it have most of the components as the ones compatible with the airplay mirroring mine does not work ?

    i have verify that all the components are almost the same please advice why because i was able to previously airply movies why not now that i have the latest os x mountain lion

    iTunes airplay still works as it always has.
    AirPlay Mirroring (the ML-added feature) requires the latest Intel hardware (specifically the Intel HD Graphics subprocessor).  This hardware includes a feature called QuickSync Video (similar to HDMI-over-wifi).
    There is no 'almost' have it.  Either you do or you do not.  It wasn't an arbitrary decision by Apple to deny older Macs of this hardware feature.

  • What is the software compatible with the BB Bold LCD screen 003/004 ?

    My screen broke, so i bought a new one and replaced it myself, but i didn't check the compatibility. I installed it but it's blank, i read somewhere that it's a software thing, so i thought maybe i could reboot my BB's whole software instead of buying a new LCD screen for 50 $. The one i bought is the 003/004, but the one i need is the 001/004. Is there any way of fixing this without having to change the screen again? i have all my info backed up so i don't care losing everything. 
    Thanks!! 

    on Windows, you can use any software to cut your mp3 for the part you want.
    you can use mp3cutter or Audacity.
    The search box on top-right of this page is your true friend, and the public Knowledge Base too:

  • I have upgraded the latest IMAC with Lion, now my remote control only operates sound level

    My new IMAC has just been upgraded with Lion OS. The remote control now only controls volume, whereas previously it controlled most media. Can anyone help?

    Frontrow is no longer part of OS X so ability to control media would appear to be gone.

  • Is the gpib232ct compatible with a macintosh?

    I'm trying to connect an hp 4145 with a macintosh. I've used the gpib232ct. Is there a way to make this work? Is the mac compatible with the gpib232ct?

    Hi,
    I asssume you are using the GPIB-232CT-A in S mode, to act as the controller. Some version of the GPIB driver supported the GPIB-232CT-A directly. Check here.
    If not, the User manual has the serial commands you can use in S mode to control the GPIB-232CT-A.
    Finally, I know some MACs use RS422 ports. Make sure you have a RS-232 port.
    DiegoF
    National Instruments.

  • Is it possible to downland itunes 10.6.3  I  have an old Macbook pro with OSX 10.5.8 and lost my itunes and cannot seem to download a version compatible with the computer

    is it possible to downland itunes 10.6.3  I  have an old Macbook pro with OSX 10.5.8 and lost my itunes and cannot seem to download a version compatible with the computer?

    Click here.
    (69952)

Maybe you are looking for