Is the USB Port in the front of G5, USB 1.1

Hi All,
Can anyone confirm this? Is the USB port in the front of the G5 only USB 1.1? I hooked up a USB hard drive to the front port and the transfer speeds were super slow. I checked the system profiler and it said the max speed was 12Mbs. Then I hooked that same USB hard drive to the back USB port and the speeds increased significantly. I checked the system profiler and it said the max speed was 480Mbs. I thought all the USB ports on the G5 were USB 2.0, or is my front USB port dying ? Please confirm. Thanks.

The USB ports on the G5 itself are USB 2.0. Those on the keyboard which came with it are USB 1.1.
(44423)

Similar Messages

  • Because of to much energy needed some of my usb port in the front hve been unactivated pls tell me how to reactivate these 2 usb port located in front

    because of to much energy needed some of my usb port in the front hve been unactivated pls tell me how to reactivate these 2 usb port located in front
    my mac pro is an early 2008 intel xeon hapertown
    thanks a lot
    patrick stanley thiollet

    Thought you could use this info about getting FireWire to work!   First, you should always Repair Permissions in Disk Utility before and after any update; I would do that now. If you installed your update with FireWire plugged in, your Mac may not recognize it anymore.
    Try resetting your FireWire ports by disconnecting all FW devices, shut down your Mac and unplug it from AC power (wall socket) for 15 minutes. plug it back in and try FW.
      If that didn't work, download the combo update from this site (yours may be corrupt), not Software Update, disconnect all firewire + USB devices except keyboard + mouse, Repair Permissions, re-install update, Repair Permissions again + try.
    If that still didn't get it Zap the PRAM. While restarting Mac hold down the following key combo Command-Option-P-R. Keep holding those keys down till you hear the second start-up chime, then release. 
    A bad internal PRAM battery can also cause FireWire to not be recognized, so make sure it's good!   Also, here is Apple doc.#88338 on getting FireWire to work.
    Here's another Fw Faq.

  • 2010 i5 MBP USB Ports Not The Same?  Griffin iMic Issue

    I have a 2010 15" i5 MBP. I got one of the white iMics and it works fine on the port thats closest to the screen. However, when I plug it in to the port that's closer to the SD slot, it doesn't work. Under the audio settings screen, I see the iMic under Input, and the slider is to the right, but the VU meter doesn't register anything. However, when it's in the USB port by the power adapter, it works as it should.
    I have read that certain model MBPs have USB ports that are not the same, and some people have problems with programs like Serato when it's plugged into the front port. Traktor and Serato have even mentioned that on the MBP there is one "good" port and one "bad" port.
    Curious if anyone else noticed this. Again, it seems to only affect 2010 i5 MBPs.

    Hi WebBrowser2,
    As I understand your query its not a single doubt you are having at all, actually it’s a bunch of multiple doubt you are carrying here in your mind allied to Mac Book Pro (USB Ports are not working).  There might be various reasons behind- not working of USB ports in Mac Book Pro, as you already had searched out various ways to fix all your issues. A few months ago, I faced the same issue as my USB port was suddenly stopped to respond, then I also tried to find various ways to get rid of this issue, and I found an informative blog link which has fixed this issue and make me tension free.
    For more information visit at- http://www.olmtopsts.com/blogs/when-macbook-pro-usb-ports-not-working.html
    And I am hoping- it will assist you in the same way as it assists me.

  • The USB port on the new keyboards

    Hi,
    I'd just like to have your opinion about the placement of the USB port on the new mac keyboard. I think it is a pity that they are so far away under the keyboard. It makes them difficult to access. Besides, what if your USB device is a bit large. You cannot plug it in for pure physical reasons.
    Another mistake from apple? What do you think?

    dwb wrote:
    But I could counter that my wife likes the way the USB port is recessed because her thumb drive fits perfectly doesn't protrude from the keyboard unlike with other keyboards. Since getting this keyboard she hasn't knocked her thumb drive lose and hasn't set her drink on it. And let's be serious - how difficult is it to lift up the keyboard to plug in a device? How onerous is it to buy a little extender if you do find lifting the keyboard such a time wasting task? Okay, I'll tone down the sarcasm
    Thanks. Point is, it adds an extra step. Macs should be more user friendly. No, it is not hard to lift the keyboard, but why should we have to when before you just saw the port and attached away?
    If you want to complain about design decisions, let's ask a few questions that might be more serious? Why is the power button hidden on back in stead of conveniently in front? Why isn't there at least a visual cue telling is where to insert a disc? Why isn't there a way to vertically adjust the display? Why are all the ports on back? Wouldn't it be convenient to have at least one USB port in front? Where is the little LED that pulses to let us know the computer is asleep?
    Well, this thread wasn't directed at the new iMac's other design quirks, but since you bring it up.
    1) Yes, that power button in the back left me scratching my head. I'm used to it now, but it is another good example of form over function.
    2) I insterted a disc backwards the first time, silly me.
    3) It is so big, why do you need to vertically adjust it?
    4) Ports on the front would make things easier, yet. And you wouldn't have to lift the keyboard But it would interfere with the clean appearance.
    5) I miss that LED too....

  • After a power outage my usb ports on the back of the tower do not recognise the apple usb keyboard upon start up. How do I fix this issue?

    I have a Mac Pro 5.1 and after a power outage my usb ports on the back of the tower do not recognise the apple usb keyboard upon start up. If I leave the plug out and then insert the keyboard after start up it works fine. The same happens with the front usb ports. How do I fix this issue?

    System.log says USB related message?
    Resetting SMC as well as NVRAM could solve the problem.
    Intel-based Macs: Resetting the System Management Controller (SMC)
    About NVRAM and PRAM

  • Why does my nook open iphoto when i plug it in the usb port on the back of my imac running 10.6.8

    I have downloaded Adobe Digital Editions and downloaded Overdrive from the public library. When I plug the Nook eReader in the USB port in the back of the iMac, iPhoto opens immediately. I know this is not a forum for Nook eReaders, but I have to start somewhere and figured since iPhoto is opening automatically, maybe someone can give me a clue.
    thank you,

    Most likely, because your Mac and iPhoto think that you have connected a camera or mass storage device that has images on it.
    Not sure where to go from there, but I would start by looking at the setting in both iPhoto Preferences and Image Capture if I wanted iPhoto to ignore that device.

  • How do I use my ipod in the car without it constantly charging?  I have to use a docking cable into the USB port because the 3.5 mm to 3.5mm jack I bought doesn't work on the ipod.

    How do I use my ipod in the car without it constantly charging?  I have to use a docking cable into the USB port because the 3.5mm to 3.5mm jack I bought doesn't work with the ipod (although it does work with an MP3 player).  My ipod is a 5th generation 80GB classic.

    I know this is old - but did you ever get this working. Thinking of getting a 780 ti card and I have an older mac with the mini-displayport too.

  • How can I connect my iPad to a TV that only has an s-video input available but also has a usb port on the satellite box available.

    I would like to connect my iPad to my older TV but the only inputs available are the s-video input port on the TV itself and there is also a USB input port on the satellite box that feeds the TV. I could also split all the RCA jacks to accomodate another input here. Thanks in advance for any and all help with this problem of mine..............RR.

    There is no s-video cable available for any iPad.
    The USB port on the cable box is for maintenance use only.
    There are RCA cables available:
    http://store.apple.com/us/product/MC748ZM/A/apple-composite-av-cable?fnode=3a

  • Hi guys well huge issue my Ipod 4th generation shuffle died and I tried to chrge it I plugged it into the USB port and the red light came on and after 5 seconds  turned off the whole Ipod is dead and I've tried in wall chargers as well that doesn't charge

    Hi guys well huge issue my Ipod 4th generation shuffle died and I tried to chrge it I plugged it into the USB port and the red light came on and after 5seconds turned off the whole Ipod is dead and I've tried in wall chargers as well that doesn't charge what should I do is there a solution or should I claim my warrenty and have it fixed??

    Also my Itunes and computer won'r reconize it

  • I have an optical mouse that came with my Mac Pro plugged into the USB port on the keyboard. After a year of working normally, the trackball all of a sudden stopped scrolling down. It scrolls up just fine, but not down. Any thoughts?

    I have an optical mouse that came with my Mac Pro, the only thing plugged into the USB port on the keyboard. After a year of working normally, the trackball all of a sudden stopped scrolling down. It scrolls up just fine, but not down. Any thoughts?

    Well
    I tried all of the suggestions, sort of. I did not have alcohol wipes, but I did take alcohol and pour some ona white paper towel and then rolled the mouse touch ball aroound and that finally cleared up the problem.  Just inverting it on paper did not do the reick, it needed some help with the alcohol.  Of course the probelm is the debris that gets inside and it really needs to come out.
    This is a huge problem for RIM devices users too.

  • HT1476 when i plug my phone into the usb port with the apple charger that came with my phone i get an error msg say charging not supported by this device.   But when i use a gigaware (radioshack brand) usb charger, no error msg.  Why?

    when i plug my phone into the usb port with the apple charger that came with my phone i get an error msg say charging not supported by this device.   But when i use a gigaware (radioshack brand) usb charger, no error msg.  Why?

    - Try restoring the iPod, first from backup and then try to factory settings/new iPod to rule out a software problem.
    - Look at the dock connector on the iPod. Look for abnormalities like bent or corroded contacts, foreign material and broken or cracked plastic.
    - Could you have damaged something when you took the iPod apart and replaced the Home button?

  • I have three ipods, none of which is being recognized by my itunes. I have the current editions and tried different USB ports. The mouse works just fine in the USB port. I have reset the ipods. Any ideas if it's the USB or the ipod or what's going on?

    I have three ipods, none of which are being recognized by my itunes. I have reset each ipod, with no results. I wonder if the problem isn't with the USB ports. The mouse works fine in each port; nothing happens when I plug in the ipods. I have tried two different USB cables. I have no other USB devices with which to test. I have made sure I have the most recent updates and rebooted the computer.  Any idea what is going on?

    Did you already have a look at this article?
    iOS: Device recognized in iTunes for Mac OS X

  • Can't use my HP Deskjet F4580 Wireless Printer with the AirPort Extreme Base. The printer is NOT connected at the USB port of the AirPort Extreme, and is placed in another room. It worked just fine with my previous router (Linksys WRT54G). Help me!

    Hey Guys!
    I just got my AirPort Extreme Base, but I can't use my HP Deskjet F4580 wireless printer with it.
    The printer is not connected to the AirPort Extreme's USB port. It is placed in another room, and I'd like to use it (the printer) wirelessly (not connected to the USB port os the AirPort Extreme), as I used to. There is no place for the printer close the AirPort Extreme. It worked just fine with my previous wireless router (Linksys WRT54G). I'm very disappointed with the AirPort Extreme Base Station because of that!...
    Can you help me? Please?!
    Thanks Folks!

    This must be a tough one, no suggestions at all.

  • My Macbook Pro Retina's USB port on the right side not working at all

    Dear all,
    I received my macbook pro 15inch with retina display a week ago, but not until today had I got the chance to use the USB port on the right side, only to find out that it is not connecting to anything at all. I have tried to use my iPhone 4 and iPad 3 with two different cables, my USB thumb drive, and my Blackberry 9900, none of them are charging nor shown in iTunes/Finder. All of above works on the left and on other windows machines too.
    I'm also not able to charge my Blackberry with the usb port on the left side, thought it would pop up a message saying "charging not supported" on the phone.
    For you information, I have applied both updates including the one released few days ago. I have also tried to reset the PRAM. Also, I have migrated from my old late 2008 13inch unibody Macbook using Migration Assistant, not sure if this would affect anything.
    I'm aware that there have been reports and discussions regarding the USB port not been able to run devices on 3.0 speed, but I wonder if anyone else have the same problem with me, where the port simply not connecting to anything at all?

    I also have a problem with the USB port on the right side of my Retina MBP.  The USB3.0 port on the left side works fine, even with high speed external SSD enclosures, like the OWC Mercury Extreme Pro 6G which enables me to copy large files at a sustained rate of 160-170MB/sec.  Wow USB3.0 and the Mercury SSD is a FAAAAST combination connected to the Retina MBP.
    However, like the forum entries about the USB3.0 ports in general on the new Retina MBP, the USB3.0 port on the RIGHT side is plagued with dropping intermittently, disconnecting my external hard drives while copying large files AS WELL AS disconnecting while just sitting there connected to an external hard drive and doing nothing.
    Therefore, since I don't feel like returning my Retina MBP and waiting weeks for a replacement, I have chosen to only use the left side USB3.0 port for now.
    I have my suspicions about why the right side USB port might be more problematic than the left side one.  I found this older post on the internet about how "Not all USB ports are created equal on MacBooks..." that talks about how on older models of MacBooks one of the USB ports shares a USB hub with multiple other devices like the iSight camera etc. therefore making it less tolerant of heavy traffic or something like that.  (http://www.wired.com/gadgetlab/2008/05/the-macbook-all/)
    Therefore, I wonder if the right side USB port is sharing a USB internal hub where-as the left side one is more 'dedicated' and therefore in my case able to handle the high speed transfers/traffic I am throwing at it with my external SSDs.
    I have also read that USB3.0 in general, on non-Macs, has had trouble for years.  For instance, some forum entries on Apple Support Communities and other non-Apple forums has made mention that 'they' are not surprised at the problems encountered on USB3.0 external hard drives connected to the Retina MBP because Windows laptops have had a lot of flakey problems with USB3.0 for 'years'. 
    Also, I have recently purchased a "Buffalo" external Thunderbolt 1TB drive from OWC and have been doing Clones onto that drive for several weeks.  I use SuperDuper to clone >600GB of data on my 768GB Retina MBP several times a week.  And, I have (knock on wood) not had any problems with the stability of my externally connected Thunderbolt drive.
    So, in my case, I am racking it up to high-speed stresses on the USB3.0 ports at least in part...and perhaps the possibility that the LEFT side USB port on the Retina MBP is more dependable and/or a more dedicated USB port than the right side one.
    This doesn't really solve your problem, but it may at least help you feel like you are not alone.

  • Recharging my iPod (3rd gen.) on my 2010 iMac goes extremely slowly (via usb port at the back). This is mainly because recharging stops when my mac goes to sleep. I just can't believe that Apple doesn't have a sollution for this, but I haven't found itth

    Recharging my iPod shuffle (3rd gen.) on my 2009 iMac (OS 10.5.8) goes extremely slowly (via usb port at the back). This is mainly because recharging stops when my mac goes to sleep. I just can't believe that Apple doesn't have a sollution for this, but I haven't found it yet... What's the most efficient way of recharging?

    Purchase a wall charger for it instead. 
    B-rock

Maybe you are looking for

  • How do i get icloud on my Macbook pro?

    My macbook pro is updated and running the newest software. I just noticed that i couldnt find my icloud on my macbook. Maybe i have never had it but i thought i did. Anyways, i went to system preferences to see if it was there to turn it on and its n

  • Server 2008 Domain Controller won't sync with domain for time

    Hi, I have a Windows Server 2008 Domain Controller, a physical machine. When I run w32tm /query /status it shows the source as: Local CMOS clock. What ever I seem to try I cannot get it to look at the PDC to sync for time. Using RsOP I can see the co

  • Inventory Management: Validity Table

    Hi Guys, For the Stock cube (0IC_C03) in BW, a validity table is generated.How to delete an existing characteristic from the validity table or how to add new characteristics to the validity table. Thanks.

  • Set Service order and Notification to 'Technical Complete.

    Need to set service order and notificatin to teco. Use below logic and it works fine for Service Orders but it doesn't set the Notification to NOCO. Can anybody please help? Thank you very much Juergen lit_methods-refnumber         ='000001'.   lit_m

  • Sql error 12705  performing CON (Upgrade on Oracle10.2.0.2)

    Hello, I'm following the Oracle Upgrade Guide_211 for Oracle upgrade to 10.2.0.2 of our test system. It's SAP R/3 4.6C with 4.6D_EXT supp. pack 2271, HP-UX 11.11 and Oracle 9.2.0.5 I'm almost done with the upgrade (just startup of SAP instance) Now I