Is there a firmware upgrade to take USB 1.1 to USB 2 to run Egalato Video Capture

We are running OS version 10.5.8 7 are using Elagato vidoe capture software.  The USB requirements are USB 2.0 however our USB port is USB 1.1.  We have all the required Apple software upddates.  Does anyone know of a how to upgrade the USB ports from USB1.1to USB 2.0?

This requires adding an expansion card with USB 2.0 ports, which probably isn't possible on an iMac.
(74778)

Similar Messages

  • Firmware upgrade cannot be installed on my 42UL863

    Hi!
    My TV does not find the any new firmware on the net, I comes back with the message that there is no any new firmware. I have 19.3.49.227 30 Aug 2011 but there is 19.3.61.7 for UL863G from feb 2012 on the toshiba site..
    When I extract and load this on a USB stick (i tried several) upgrade seems (after Yes click) to start, the "upgrade" popup shows up but the progressbar does not change and it comes back after a while with something like "upgrade file cannot be found"
    Any ideas?
    Cheers!

    Hi
    Here is another [How to update the firmware|http://fget.dl.toshiba.com/manual/procedure/10002/procedure_of_downloading.pdf?fromPid=%2Ftsb-dtv%2FNA%2FGB%2FEN%2F42UL863G.html&f=procedure_of_ downloading.pdf]
    Not all USB Thumb drives will work for Firmware Upgrading. The USB
    Thumb Drive should be formatted as a FAT or FAT16 fi le system and NOT FAT32. If the
    Firmware Upgrade does not work try a different USB Thumb Drive.
    Copy the extracted downloaded upgrade file(s) including directories if present to the blank
    USB Thumb Drive. Now follow the instructions in the Installation Instruction.

  • Firmware upgrade for WRT54G v7

    is there no firmware upgrade for WRT54G v7? i didn't even find version7 as listed in linksys page for routers....

    Click on Download and save the file on your Desktop..
    Follow these steps to upgrade the firmware on the device : -
    Open an Internet Explorer browser page on a computer hard wired to the router...In the address bar type - 192.168.1.1...Leave the Username blank & in Password use dmin in lower case...Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab-Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...Wait for few seconds until it shows that "Upgrade is successful"  After the firmware
    upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
    Now reset your router :
    Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

  • N95 firmware upgrade

    would anyone happen to know when nokia will release there next firmware upgrade for the n95 i am currently running 12.0.013....just curious, and whats APAC how do u know if your n95 is APAC>.
    NOKIA N96 rocks

    I thought APAC was the acronym of Asia-Pacific.
    * Australia
    * Brunei
    * Cambodia
    * People's Republic of China
    (including Hong Kong and Macau)
    * Taiwan (Republic of China)
    * Fiji
    * Guam (U.S. territory)
    * Indonesia
    * Japan
    * Kiribati
    * North Korea
    * South Korea
    * Laos
    * Malaysia
    * New Zealand
    * Northern Marianas (U.S. territory)
    * Palau
    * Papua New Guinea
    * Philippines
    * Samoa
    * Singapore
    * Thailand
    * Timor-Leste
    * Tonga
    * Tuvalu
    * Vanuatu
    * Vietnam
    Ericssson EH 237, Ericsson EH 337, Ericsson GH 388, Siemens S25, Nokia 6210, Nokia 7250, Nokia 6230, Nokia 6280 & O2 Atom , Nokia N95, Nokia 5800 XpressMusic

  • Qosmio F15: card reader firmware upgrade to read type M xD cards?

    I've done a little research and haven't found an answer to this question...
    Is there a firmware upgrade to a Qosmio F15 laptop that will allow the multiple card reader to read Type M xD cards?
    It reads the standard xD cards but I bought a 512Mb card and it will not read it.
    Thanks

    Some units support only a certain cards and not all card sizes.
    Possibly this card is not compatible with the card reader slot.
    I have investigated a little bit on the US Toshiba site and found out that this notebook supports secure digital cards 256MB SD-M256B3 and 512MB SDM5124B3
    However, you can try to update the texas instrument flash media driver:
    Have found this interesting Toshiba document:
    http://www.csd.toshiba.com/cgi-bin/tais/su/su_sc_dtlView.jsp?soid=1474485&BV_SessionID=@@@@07 57628877.1158743881@@@@&BV_EngineID=ccciaddilfkkee gcgfkceghdgngdgnj.0
    good luck

  • WRT150N Firmware Upgrade

    I have a WRT150N V1.0 but when I try to use the link to upgraade the firmware it gives me a http404 error:File not found.  The upgrade link works for V1.0x and above but not for 1.00.  Can I upgrade using the working link or is there no firmware upgrade for the version 1.0.  Thanks

    Download 2.67 MB the firmware for WRT150N v1.

  • BDX2300 firmware upgrade fail (USB)

    I have had mulltiple screen freezes on most Bluray discs I have tried. I see there is a firmware upgrade 1.15 to stabalize, but...
    I have followed the instructions for copying the files for firmware upgrade to USB drive in Directory UPG_ALL. When I plug the USB drive into the player, I see the USB icon loading, but the player does not try to load the firmware as the instruction states:
    3)
    “Insert the USB Thumb Drive with the firmware” copied to the drive into the USP port located on the front. (Note: Some models may have the USB port located behind a protective cover or on the rear of the unit)
    4)
    After a few seconds the update screen will appear. The unit will automatically update the firmware in sequence as shown in Figure 1a through 1d.
    If I go to Setting, system, and try to upgrade from USB, I get a messsage that the file is not found. I have verified the files are in the directory as requested.
    What are the correct instructions that will allow me to update my firmware via USB?

    I just successfully upgrade my brother's machine thanks to this forum:
    Here is what worked for me with upgrade V1.22. after much trial and error: (Your folders will have your version in the name)
    Unzip the downloaded zip file. There is a real nice PDF file that tells you exactly how to do it. THROW IT OUT!
    On a clean thumb drive (don't worry about  BUDA and System Volume information) create a folder named  UPG_ALL.
    When you unzip your file you will find, besides the PDF file you should dispose of, a folder named V1.22. In that folder you will find yet another folder named V1.22.
    In that folder you will find some files: I had the following in mine:
    8551_linux_demo_dbg.bin
    8551_linux_demo_dbg_id.bin
    DVD.bin
    dvd_id.bin
    mt8551_bl_linux.bin
     Copy those files to the UPG_ALL folder on the Thumb drive.
    Now some of you may have gotten this far before, what they didn't tell us was that you can tell the player to look on the USB port.
    With thumb drive inserted and the power on select the icon on the tv screen with the gears. Then select SETTINGS and  then select UPDATE.
    You should now see a choice  for disk - USB - or network (or something like that)
    Select USB and wallah you should have an update occur.
    This last part was strictly from memory, because I couldn't interupt the movie my brother  was watching.
    I hope this helps,
    Jerry

  • I got a message in gmail "this version of Safari is no longer supported.  Pls upgrade to a supported browser."  When I click on 'supported browser' it takes me to Apple's Safari site but there is no 'upgrade now' button.  What am I missing?

    i got a message in gmail "this version of Safari is no longer supported.  Pls upgrade to a supported browser."  When I click on 'supported browser' it takes me to Apple's Safari site but there is no 'upgrade now' button.  What am I missing?

    Google seem to have decided in the last week or so that Safari 5.x, which is the newest Safari version available for Mac OS X 10.5 (Leopard) and 10.6 (Snow Leopard) is "not supported" any more, even though there are many reasons for staying with these OS X versions.
    Try this (at your own risk, but it works for me), as it seems to remove the message by tricking Gmail into thinking your Safari version is newer:
    -- Quit Safari
    -- Locate the following file (location depends on your OS X version):
    OS X 10.6 Snow Leopard:
    /System/Library/PrivateFrameworks/WebKit2.framework/Versions/A/Resources/Info.pl ist
    OS X 10.5 Leopard and older:
    /System/Library/Frameworks/WebKit.framework/Versions/A/Resources/Info.plist
    -- Drag the file to your Mac's desktop to make a copy. Also make a safe copy somewhere else eg your Documents folder, as if you lose or mess up the file Safari will not launch at all. Having a backup browser is also recommended.
    -- Double-click it to open it in TextEdit
    -- Locate the CFBundleVersion value (the last line in the file that has numbers in it) and increment the second digit of it to the required version of Safari e.g. Safari 6 now seems to be the minimum version that Google support so change the second number from 5 to 6 (don't change anything else, only the change the second number). The value is different depending on your OS X version but as an example, for Snow Leopard 6534.59.10 becomes 6634.59.10
    -- Drag the file back from the desktop to its original location, choose the option to replace the old version, and enter your password when prompted.
    -- Run a permissions repair in Disk Utility to set the permissions in the file back to what they should be (not required, but good practice).
    -- Launch Safari and test Gmail.

  • My BB 8520 won't connect via USB after the firmware upgrade

    Hi,
    All was working fine until I followed the upgrade prompts. The 'phone works but a) it won't accept Opera Mini 5.1 (which was in the 'phone already) and b) I cannot connect to the PC via the USB cord.
    What happened?
    This 'phone shares the same SIM card with 3 Nokias (E72, E90, E62) and I've never had firmware upgrade problems with them - in Symbian OS.,
    Any ideas?
    Regards, Douglas
    L. Douglas Henderson - ARTCRAFT Music Rolls
    EDIT: Link Removed. Please review User Guidelines  under section "No spam please."

    Hi, again -
    Just downloaded Bolt and I like it also. (No more zooming: whoopee!)
    Never heard of this browser before, having used Opera Mini/Mobile (depending upon the 'phone) since 2004. Was on E-Mails for cell 'phones dating back to 1997, coast to coast: primitive service back then! [Rarely did I use the default browser on any 'phone I've had, including Motorola and Palm before Nokia.]
    Bolt loaded faster than Opera Mini 5.1 did on my Nokias and the Blackberry 8520: amazing!
    Now my "not as good as a Nokia with Symbian" handset is useful again. The firmware upgrade did improve the videos and the links to them, so it was a GAIN SOME FEATURES and LOSE SOME FEATURES firmware upgrade.
    Probably Opera will have a link for the Blackberry 5 platform, eventually. The problem, I think, was that the link only worked with three versions of their 4 edition.
    You have made my day!
    Thanks.
    Regards, Douglas
    PS: Not until the Nokia E90 Communicator was off the market for a year or so, did Opera put out a Mobile browser which functioned on it. The Communicator - in a variety of versions - had a 12 year run in Finland, something of a record for handsets in this field. For Word .docs, fast typing and office style activities, it's hard to beat. (You can't wear one in your pocket if the garment is Spandex, of course.) The music on the E90 is loud and good; with the wireless aux. speakers it rivals a portable stereo, so I use it for that purpose much of the time, even when off-line.

  • Is there USB 1.1 to USB 2.0 Upgrading Software-Patch?

    Hello,
    I wanted to buy External-DVD-Writer with USB connection,
    all the models are *USB 2.0* specific,
    my imac has *USB 1.1* on the computer and the keyboard,
    sales person told me that there is *USB 2.0 UPGRADE* that i can download
    and upgrade my *USB 1.1* to *USB 2.0*.
    Is there such a download?
    Thank you.

    Hello, 
    It would be far better to purchase a Firewire External Drive. You cannot boot a PowerPC (G4) iMac from a USB drive and Firewire is faster for sustained transfers than USB2.0.
    OWC DVD±RW DL Burner.
    I would suggest that you shop elsewhere in future; this sales person clearly doesn't understand what they are trying to discuss(!).
    mrtotes

  • I have two macs in my house.  One is newer and came with the os x mountain lion software and the other one needs to be upgraded.  I was wondering if there is a way to take upgrade from one to the other?  Should not have to buy this software again.

    I have two macs in my house.  One is newer and came with the os x mountain lion software and the other one needs to be upgraded.  I was wondering if there is a way to take upgrade from one to the other?  Should not have to buy this software again.

    Welcome to Apple Support Communities
    Buy it for the other computer. Mountain Lion is preinstalled on the new Mac, but you can only use it in the new one

  • Is there a firmware update for the Apple RAID Card [early 2009 Xserve] that will take it beyond the E-1.3.2.0 version and allow it to see 4TB drives?

    Is there a firmware update for the Apple RAID Card [early 2009 Xserve] that will take it beyond the E-1.3.2.0 version and allow it to see 4TB drives?

    I have a few of these RAID cards in a couple servers, and then I have an earlier version of the RAID card in a few different servers.
    The earlier servers are running non-apple 1.5 TB drives. It will be interesting to learn if this firmware update will indeed allow me to boost the capacity by installing non-apple drives, as the firmware previously has not.
    Ohh I'm excited to update and try! This will greatly help out if it does!

  • I just did a firmware upgrade and there is no eprint logo on the front of my computer. what now?

    i just did the firmware upgrade for eprint. there is no logo on the front of my printer and the guide doesn't tell you where to go if you don't have this. I would like to setup eprint but i don't know where to go from here. How do i find my printer's email address?

    Hi piedmont44v,
    I'll be happy to help you with this.  If you don't mind, what model is your printer?  Our process will be determined by this information.
    If I have solved your issue, please feel free to provide kudos and make sure you mark this thread as solution provided!
    Although I work for HP, my posts and replies are my own opinion and not those of HP.

  • Is there going to be a firmware upgrade for mountain lion customers that have a Macbook with a soild state drive so we can use the Power Nap feature?

    Is there going to be a firmware upgrade for mountain lion customers that have a Macbook with a soild state drive so we can use the Power Nap feature?

    here: http://www.apple.com/osx/whats-new/
    "Power Nap requires a Mac notebook with built-in flash storage. May require a firmware update."
    We have to wait for the Firmware-Updates. Some are already here: http://support.apple.com/kb/HT5394
    And I am shure, that you will need for Power Nap one of the newer Macs with SSD from 2011 and 2012.

  • Zen Micro undetected, after PlaysForSure Firmware upgrade! *USB 2.0 er

    Half way through the PFS?firmware installation, a Found new Hardware window pop up, prompt me to install software for USB 2.0 device. I carried on to install hardware, but it just can't find the suitable software. After I close the pop up, the upgrade installation went dead. The next time i plug my zen micro, the pc can't detect it! The only thing workable is the removable disk. I can't reinstall the software becos the pc cannot detect the zen micro (i tried all usb ports)?Some other info:-Everytime i plug my zen micro in, the Found new Hardware window will pop up, prompt me to install software for USB 2.0 device. Before u tell me it's my chipset problem, i have no problem with other devices that use usb 2.0, and this problem occurs ONLY after i tried installing the firmware, ONLY on zen micro. My zen micro was working PERFECTLY fine before this. -My?zen micro's system information states that the firmware is 2.2.02, though i mentioned earlier that the installation went dead. I am pretty sure this undetection problem is cause by the firmware upgrade. I hope all zen micro users who read this post will stop their intention to upgrade to this firmware, until a solution arri'ves. Hope i can have some "real" help on this. Any user from this forum who has the same problem, can post to share. Anyone who are able to solve this, pls post too, much appreciated.

    Dear Creative!
    You screwed the upgrade program a bit, because it is works ONLY IN ENGLISH version on Windows XP. Shame! You are pushing me into the sea of warez...

Maybe you are looking for

  • Calling a report from a form and outputting to the screen.

    Hi all, I created a report from the Report node in Forms called Monthly_rep. It points to a .rdf file on the server that produces a monthly usage report. When run from Reports Builder both the web and paper version are fine. I have a button on a form

  • Can I Create A Hotspot With My iPhone 4 To Use For iPod Touch?

    I'm considering signing up for the tethering plan with AT&T. My main purpose would be to create a hotspot for my iPod Touch. I use my iPod Touch at work using Keynote.  I would like the ability to download my Keynotes via Dropbox on my iPod Touch. Ca

  • I have lost all sound,webcam & dvd driver

    I have tried re-installing drivers. But shows as no device's found

  • How do I get photos outside of iPhoto?

    I recently had to restore my computer and the iOS was updated to mountain lion or something... Anyways, all my photos are inside iPhoto. However with the new version of iOS I can't open that version of iPhoto on that macbook. So I copied the iPhoto i

  • Toplink 10 g, 11g

    is there any major difference between these two versions. wht new modifications ve done in 11g