Is there a way to preset the cFP-QUAD-510 module?

Using MAX, there is a way to reset the cFP-QUAD-510 to zero. However, is there a way to preset the counter programatically through LabVIEW to count values other than zero?

Dave,
With the 1-50 Hz range that you are trying to measure, you are correct in your assessment that the CTR-502 module would provide a more accurate reading. Just for everyone's benefit, let me give a quick explaination of why this is.
The QUAD-510 module has only eight allowable timebase settings for velocity measurements. The timebase is essentially the "window" over which your quadrature encoder signal pulses are counted, and is equivalent to the gate signal that is used when doing frequency measurements with the CTR-502. The longest window that can be applied with the QUAD-510 is 26,214.4 us, which results in a velocity resolution (accuracy) of 38.15 counts/s or 38.15 Hz. As such, when trying to measure frequencies in the range of 1-50 Hz, your accuracy will be very low.
The CTR-502, on the other hand, can get much more accurate measurements at this frequency range because you can configure a much longer window. There is a LabVIEW example that installs with the FieldPoint driver called "Frequency Measurement.vi" that shows how to do frequency measurements with the CTR-502.
Dave, if you would like to see better resolution for low frequency measurements with the QUAD-510, again, please feel free to submit a product suggestion for this functionality. For now it sounds like you have the best hardware setup for your application. I hope that the information I have provided has been helpful.
Best regards,

Similar Messages

Is there a way to preset counters

During a certain process I'm starting a continuous encoder measurement. This measurement has to be stopped (with Stop Task) at a certain event because I have to change the Sample Clock of the acquisition. When I restart the encoder measurement, the counter value is (logically) set to 0 but I don't want to loose the previous counter value. Of course I can put this previous value in a variable and use it as an offset but is there a way to preset the counter?

See Count Digital Events.vi in the LabVIEW examples (Hardware Input and Output >> DAQmx >> Counter Measurements >> Count Digital Events).

I am trying to crop faces from old family group photos and paste them on to records in Family Tree Maker. When I do this, the pasted cropped image reverts to the original of the entire family. Is there a way of unlinking the original version from the crop

I am trying to crop faces from old family group photos and paste them on to records in Family Tree Maker. When I do this, the pasted cropped image reverts to the original of the entire family. Is there a way of unlinking the original version from the cropped image?

Are you copying the cropped images directly from Aperture's Browser window and then pasting into your family tree?
It would be safer to export the cropped faces as new image files to a folder on your disk, and then drag them from there to the "Family Tree" window.
To export select the cropped image versions in Aperture's browser and use the command "File > Export > Version". Select a suitable export preset from the pop-up menu, for example "Jpeg fit into ..." and select a folder to export to.
Regards
Léonie

I create a birthday calendar in iCal and then click on it in iphoto at the begining of the calendar project each year. Some how the birthday did not populate the photo calendar. Is there a way to add the birthday iCal calendar into the calendar project?

I created a birthday calendar to use in iphoto for calendar. When a new calendar project is started each year, I click on it in. Some how the birthday did not populate the photo calendar this year. The photo calendar is almost complete. Is there a way to add the birthday iCal calendar into the calendar project? I would prefer not to start over.

Hi,
If you first select the calendar on the left, so that its background is highlighted blue/grey, when you make a new events they should be added to that calendar.
Best wishes
John M

Is there a way to adjust the settings on launchpad so that when I swipe into it all the open apps/pages are fully separated (like in exposé) so that I can fully view all of them simultaneously?

Hi Apple community,
This is my first go at this so be kind,
My question concerns launchpad. Coming from Snow Leopard I had been using spaces. I like to keep certain bundles of programs on separate desktops, for example all word processing related tasks in one place. I have set up the equivalent on Yosemite.
My problem is concerns the loss of exposé. Now I know when you swipe into launch pad you get a very similar effect but the issue I am having concerns the "zoom out" effect when you swipe into launchpad. With exposé all open apps/pages etc would be fully exposed - in my case several (sometimes as many as 9 word documents). What I am running into is when I do this in / into launch pad the "pile" of docs is exposed but they are still overlapping so I can't get a good look at which is which and visually identify where I want to navigate to.
My question is this; Is there a way to adjust the settings on launchpad so that when I swipe into it all the open apps/pages are fully separated (like in exposé) so that I can fully view all of them simultaneously? If so, instructions on how to do so would be greatly appreciated. Any alternative suggestions to doing this outside of launchpad are also welcome. If there is an exposé app for example, I would be quite willing to go that route.
My main concern is being able to quickly (ie a touchpad gesture) expand all the open pages so I can bounce between them.
Much thanks from a loyal Apple friend.

Hey Eric,
Thanks for taking the time. Unfortunately no that does not solve it. Same as swipe it will get me there and it will show separate programs spaced out. The issue I am having is that all my open word files are bunched up in a pile on top of each other. I can see the edges of each one but I want them to be separated from each other enough that I can visually identify what file is what.
Again, thanks for trying, it is appreciated.

Is there a way of stopping the battery from charging?

Dear Apple Community,
Recently I installed iStat Menus and found that, over the course of this year, my Macbook's charging capacity has dropped 5%. I know this isn't a massive number, but battery performance has become a concern for me. I use my Macbook as a desktop replacement, on the main. It's sitting on a mStand, connected to a large monitor on my desk. I use my Macbook to play games, surf the internet, do work and all that good stuff - basically, I use it for everything. I rarely use the Macbook without it being plugged in. I read on the Apple website that they do not recommend leaving the Macbook on charge permanently and that I should use it on battery at least one a month. As I use my Macbook as a desktop replacement, I don't actually have a lot of opportunity to do this.
My question to you, the community, is: is there a way of stopping the battery from charging, either with the use of an app or a physical device? Ideally, I would love to have my power plugged in BUT only used when the battery drops below 10%. Is this possible with an app?
On the other hand, am I just worrying about nothing? Will my battery be damaged further if I leave the Macbook charging permanently?
Thanks for your help!
Jeremy Reid

Ideally, I would love to have my power plugged in BUT only used when the battery drops below 10%. Is this possible with an app?
The charging characteristics are handled in firmware. There is no app that would be able to do this. You actually would not want to do this anyway. Regularly discharging your battery to 10% will greatly decrease the life of your battery. While it is true that you should not use your system exclusively plugged in, allowing it to run on battery a few hours a week should be fine. Letting the battery regularly run down to (or below) 10% will cause you to use up cycles more quickly than is necessary (thereby reducing the life of your battery). It's really a only a matter of disconnecting your Magsafe connector once in a while.
Leaving it plugged in does not result in it being charged "permanently". It will charge until it is full and then charging will stop. It will only begin recharging when it reaches about 95%.

Is there a way of making the Edge Commons parallax effect work smoothly with DPS on the iPad?

I want to create a feature for an iPad magazine utilising the parallax effect shown here...
Parallax Scrolling Made Easy (Adobe Edge Animate Online Week, Episode 9) - YouTube
I am using Digital Publishing Suite to publish to an iPad. I ran a test and the effect partially works, but not smoothly.
As you scroll down the animation does not play. Once you finish scrolling the animation then jumps to whichever point has been reached on the timeline, rather than animating as you scroll down the page.
Is there a way to get the same animation effect through DPS that you see in the browser? Or is it not compatible?
Thanks!

As lllaass said, you can't.
If you want Apple to add backgrounds to the iPad version, leave them feedback: http://apple.com/feedback/ipad.html.

Is there a way of connecting the ipad to the smart board in the classroom, so that the smartboard is the control, and the ipad is displaying what is on the smartboard? This is to help a visually impaired child see what is on the smartboard.,

Is there a way of connecting the ipad to the smart board in the classroom, so that the smartboard is the control, and the ipad is displaying what is on the smartboard? This is to help a visually impaired child see what is on the smartboard.

Absolutely!
Install Splashtop2 on the PC and enable it to be controlled or ran from iPad or Reflection to simply allow iPad to serve as PC unwired monitor. With Splashtop and an Apple TV connected, you use the smartboard as usual, yet the PC and iPad can see the same content. The impaired child can even interact with the Smart Board via the iPad as if he were writing directly on the big screen. Erasing functions can be done by touching the Smart Board manual controls. Several variables are in play that cause this lack of functionality:
    Apple won't permit PC software that infringes its proprietary apps.
    Smart Board companies refuse to develop iPad apps because they feel threatened and are being replaced by iPads
    School districts think Apple TV is meant for copyright infringement and could expose them to safe harbor lawsuits
    Network administrators make it impossible to login Apple TVs because they don't want the streaming occurring
    Classrooms are not able to keep up with the technology of using the iPad
    Clicker companies refuse to play with iPad because they see it as a potential threat to their core business clients
    Apple is not working as hard as it could to exploit its capabilities in education, thus losing money in iPad sales
The bottom line is that we educators and technology developers are hurting our childern with petty conflicts.

Is there a way to darken the dates (numbers) on ical. After installing Lion I can barely read the dates of the month in ICal

Is there a way to darken the dates (numbers) on the ICal calender. I can barely read mine after installing Lion.

I should note that the time stays on the left of the event name when I re-enter the text (which I had to do all the time before I found the "show event times" button) so I feel like there's a way.

Is there a way to open the right click menu on the left side of your pointer?

Whenever I try to right-click an object that's located on the right side of the screen, the pointer always automatically click whatever entry in the right-click menu which just happens to be under the pointer the moment the menu is opened. I noticed that the reason this happens is because the right click menu always forces itself to open on the right side of the pointer, and when there isn't enough space, the right-click menu will open underneath the pointer. Since this is horribly inconvenient, is there a way to open the right-click menu on the left side of your pointer?

Are you saying you have an icon on the far right side and when you rt click on it, your pointer ends up opening wherever it lands? That is a two step process, or normally should be at least a two step process. Do you have a Mouse in your Control Panel? You should check, because there may be some properties with which you can play. For instance, I can switch primary and secondary functions on my mouse buttons by checking a box.
When I rt click on right side, the menu opens on the left.
When I rt click on left side, the menu opens on the right.
In order for me to take an action, I then have to move to an area in that menu and click.
I hope I understood your question correctly.

Is there a way to open the mic using apple remote desktop

Is there a way to open the mircophone channel using Apple Remote Desktop so I can listen on anything thats happening at my computer at home? If not is there another software that would work?
Also is there a way to use apple's software to control and watch a PC?

Is there a way to open the mircophone channel using Apple Remote Desktop so I can listen on anything thats happening at my computer at home? If not is there another software that would work?
You would have to launch software that would accept audio from the microphone and transmit it to you in some fashion. ARD does not transmit audio itself. Another remote control solution such as Timbuktu might transmit audio, so you could look into that, perhaps.
Also is there a way to use apple's software to control and watch a PC?
You can install a VNC server on the PC and ARD can then take control of the system. It can be tricky to find a VNC system that will work with ARD, though, so search this forum for "VNC" for possible options. One of the applications that support Microsoft's remote desktop architecture such as their own Remote Desktop Connection Client for Mac or iTap Mobile RDP will probably work better, though.
Regards.

Is there a way to open the notification pane using magic mouse?

Is there a way to open the notification pane using magic mouse? i mean it would be great if i could two finger swipe to the right for the notification pane (two finger swipe left opens dashboard)
I have Magic Prefs if it helps

It doesn't seem like this is possible in 10.9.1. Can someone at Apple confirm or provide a solution?

My child accidentally rented a movie on Apple TV. Is there a way to refund the rental if we don't watch it? How can I prevent this from happening? Is there a way to password protect future purchases?

My child accidentally rented a movie on Apple TV. Is there a way to refund the rental if we don't watch it?
How can I prevent this from happening? Is there a way to password protect future purchases?

Did you try Parental Controls?
Apple TV: Understanding Restrictions (parental controls) - Apple Support
See if that does the trick: I think there's a way for you to request a password for purchases, but still be logged in.

Is there any way to prevent the OS from querying the Superdrive when start

Just a random question. Whenever my MacBook Pro starts up (either from sleep or a complete/fresh start, the OS queries the drive slot to see if there is a disc present. While this may be normal behavior, it seems to slow down the start up process. (I rarely ever have a disc in the drive). Just curious if this, in fact, normal, or if there's something awry.

Is there any way to prevent the OS from querying the Superdrive when start
No
he OS queries the drive slot to see if there is a disc present.
How can you tell? Based on the noise it makes?

Is there any way to retreive the FileName in the mapping

Is there any way to retreive the FileName and so that I can use that in my mapping. This is FILE2RFC scenario with NO BPM.
I am using the adapter specific message attributes in the file sender CC.
Thanks,
Ravi
null

Yes you can retreive it. Create an simple user defined function in the mapping and use the following code.
Imports: com.sap.aii.mapping.api.*;
Parameter: String filename
Paramter: String filename;
filename = fileName + ".DAT";
DynamicConfiguration conf = (DynamicConfiguration) container
.getTransformationParameters()
.get(StreamTransformationConstants.DYNAMIC_CONFIGURATION);
DynamicConfigurationKey key = DynamicConfigurationKey.create( "http://sap.com/xi/XI/System/File", "FileName");
conf.put(key, filename);
return filename;
Or
Just do whatever mentioned in this weblog:
/people/michal.krawczyk2/blog/2005/11/10/xi-the-same-filename-from-a-sender-to-a-receiver-file-adapter--sp14
---Satish

Is there a way to preset the cFP-QUAD-5​10 module?

Similar Messages

Maybe you are looking for

Is there a way to preset the cFP-QUAD-510 module?