Is there an extender for Airport Extreme?

Airport Extreme does not reach the back of the house. Is ther an extender?

You can buy and use an Airport Express as an extender for your wifi signal. Generally, the Express would be located halfway between the Extreme and the area that you want to extend the wifi signal to. The Airport and Extreme must be in radio range of each other to be able to perform this function.

Similar Messages

Are there updates available for Airport Extreme? If there are, will I be notified of an available update?

Are there updates available for Airport Extreme? If so, will I be notified or should I check from time to time for any updates?

Back up your data, check your applications for compatibility, and download Mavericks from the Mac App Store.
(108187)

How do I use an Airport Express as a "range-extender" for Airport Extreme?

I bought an Airport Express with the intent of using it as an "extender" for my Airport Extreme, but I find no paper that describes how this is done. Any suggestions would be appreciated.
Thanks and cheers, Veit

Thanks for the info. Try this to see if it will do the job for you:
_On your AirPort Extreme (AEBS):_
Open AirPort Utility and click Manual Setup
Click the *Wireless tab* below the row of icons
Your *Wireless Mode* should already be set to “Create a Wireless Network”
Make sure there is a check mark next to “Allow this network to be extended”
Note the setting for Wireless Security as you will need this for the next setup on the AirPort Express
Update to save changes
_On the AirPort Express (AX):_
Hold the reset button in on the AX until you see the amber light begin to blink more quickly
Temporarily, move the AX near your computer and connect a short ethernet cable from your computer to the AX
Open AirPort Utility and click Manual Setup.
Click the *Wireless tab* below the row of icons
*Wireless Mode*….should be set to “Extend a wireless network”. If you don’t see this choice, hold down the option key when you click on the selection box
Wireless Network Name…the name of your main AirPort Extreme network should appear as a choice. Click to select it.
Place a check mark next to Allow wireless clients
Wireless Security….exact same setting as your AEBS
Wireless Password…exact same password as your AEBS
Confirm Password
Click the Base Station tab to assign a name and device password for the AX, set time zone, etc.
Click the Music icon to enable AirTunes if you wish
Update to save settings. You can disconnect the ethernet cable and move the Express to the desired location.
For further reference, Apple's instructions for the "extend" setup appear on pages 43-44 in the Apple AirPort Networks Guide.
Please post back on your results.
Message was edited by: Bob Timmons

Is there an update for airport extreme that is about seven years old?

is there an update for an airport extreme purchased about seven years ago? The signal in my whole house goes down and has to be re-booted quite often.
I had a service call down by my cable company and their "arris" box in my house sends out a decent signal but the airport extreme gets "bottle-necked" per the service man
Thanks!

Check the firmware on your AirPort Extreme. The last firmware version for it was version 5.7, however, there were some fairly well-known problems with it that would cause it to become apparently unreponsive on occasion, and require the need to completely power down the Extreme.
If it is running firmware version 5.7 or 5.6 try downgrading it to firmware version 5.5.1. The older AirPort Extreme had a problem with 5.7 that would cause the problem you described, and 5.6 was even worse.
In other words its two most recent firmware updates made things worse. Having experienced this identical problem with two 802.11g/b Extremes, I suspect they had a fundamental flaw that Apple never admitted, but solved with the introduction of the new 802.11n models.
If you are running the most recent version of AirPort Utility for Lion, the option to upload firmware 5.5.1 to your Extreme is not likely to be available though. I am reasonably sure that AirPort Utility 5.5.3 will include the ability to upload an earlier firmware version to your Extreme.
Try it. It could make things better, or worse, or could introduce an entirely new problem, but you can always undo your troubleshooting by uploading the most recent firmware again.
Ultimately you may come to the same solution as I did, which was to buy a new 802.11n Extreme.

Is there a FAQ for Airport Extreme/Time Capsule & wireless printing?

I have an Airport Extreme Wireless "N" with Time Capsule and want to set up a printer. To my dismay, I cannot find the booklet that came with my Time Capsule and just need to know the basics of setting up the printer too the Wireless router (airport+time capsule).
Sorry to ask such a dumb question, but can I just plug the printer in to the USB port on the wireless router? Or should I plug it into the wired router that the airport router plugs into?
Thanks.

You plug it into the USB port on the Time Capsule.
The Time Capsule manual that you lost can be found and printed here:
http://manuals.info.apple.com/enUS/TimeCapsuleSetupGuide.pdf

How do I extend my Airport Extreme version 5.7 for better wireless at a distance?

From my researching of this problem, it seems like I may need to "extend" my Airport Extreme version 5.7 to strengthen my signal at a distance. It is used, but I was able to reset and set it up to my network. The previous user was getting much better performance. When at my desk, right next to the router and Airport Express, I get up to 19Mbps. At a distance of 30-50 ft. (which I often use) wirelessly, I can only get up to 4Mbps. Will "extending" the Airport help those speeds and strengthen the connection so as not to burden it even farther with 3 users connected to the network or is there something else that I can do? Am I just being picky? I am an Apple novice and have read everything I can to figure out my problems, but this one is still lingering. Problem or not?
Info: if needed
Airport Extreme v 5.7 - only one as a base station
Wireless network with ZyXel Q1000 router - Airport Extreme is connected to that via ethernet cable.
I use a Toshiba Satellite laptop, less than a year old running Windows 7.
Often work about 30-50 feet away wirelessly and speeds are up to par without Airport Extreme, got it to strengthen signal as another user will be added to my network shortly. Speeds at a distance 4Mbps or less. Next to router and Airport 19 Mbps.
I have Century Link 20Mbps high speed internet service.
Airport "dome" has three lights on top. Middle is steady green and the two on each side periodically blink white.
Successfully set up using airport utility for PC. It shows up on that list and on my wireless connection list.
Thanks in advance for any and all suggestions or positive comments.
david
badboyfun - apple novice.

I'm having a bit of trouble confirming that the ZyXEL is a combination modem & wireless-N router. If it is, then you really won't get any advantages of using the 802.11g AirPort.
If the range of your ZyXEL is limited, you may find that doing either or both of the following will help: 1) Move the ZyXEL so that it is higher vs. lower in the room, that is away from any closed areas or placed in a metal cabinet, and 2) Changing radio channels. The latter is especially important in you live in an area where there are a number of competing Wi-Fi.
A good utility to find out, is iStumbler. You would use this to find these other Wi-Fi and find which have the strongest signal value. Those that do, you would also want to note which channel they are operating on, and then, change yours to one that is at least 3-5 channels away. So, for example, if you find strong ones on channels 1 & 6, change yours to 11.

Extend Air Omni for Airport Extreme

I buyed from Apple Store Online the Extend Air Omni for Airport Extreme, but now my Airport Extreme don't have a antenna port.
It's possible ?

Only the M8799LL/A & M9397LL/A models of the AirPort Extreme Base Stations (AEBS) provide an external antenna port which you can plug the ExtendAIR Omni.

Is the maximum number of users for Airport Extreme per device, i.e. 2 AEBS = 100 users, one AEBS extending the other on the same wireless network?

Is the maximum number of users for Airport Extreme per device, i.e. 2 AEBS = 100 users, one AEBS extending the other on the same wireless network?

50 users per device, assuming that the "main" router is setup to deliver an adequate number of network IP addresses for all devices.
2 AEBS = 100 users, but that is really more of a theoretical max.
If you really need 100 connections, it would be much better to use 3 AEBS to spread things out.

HT4259 Q: Can I use an older Airport Express-g router (not -n) to extend my Airport Extreme-n wireless network? If Yes, are the instructions the same as for adding an Airport Express-n router?

Q: Can I use my older Airport Express-g router (not -n) to extend my Airport Extreme-n wireless network? If Yes, Are the instructions the same as for adding an Airport Express-n router?

If you want to extend, using wireless only, the 802.11g Express doesn't support this.
However, if you want to use bridge mode over Ethernet or Powerline adapters then this is supported.

I am extending my airport extreme by adding an airport express. I had no problem setting it up and got green lights but now I cannot get on either because it says it is a self assigned IP?

I am extending my airport extreme by adding an airport express. I had no problem setting it up and got green lights but now I cannot get on either because it says it is a self assigned IP?

i am extending my airport extreme by adding an airport express.
Does this mean that you are connecting the AirPort Express to the AirPort Extreme using a wired Ethernet connection....or....are you connecting the AirPort Express to the AirPort Extreme wirelessly?
but now I cannot get on either because it is a self assigned IP?
I suggest that you first concentrate on getting the AirPort Extreme working correctly. Power off the modem and both the Extreme and Express, wait a few minutes, then power up the modem and let it run a few minutes. Then, power up the AirPort Extreme and check the network for proper operation. Leave the AirPort Express off for now. Report on your results.
We need to know what operating system you are using on your Mac or PC in order to provide more troubleshooting help.
If you have a Mac and do not know what operating system you are using, click the Apple icon in the upper left corner of the screen, then click About This Mac. Post back with the OS X version number that you see there.

Airport Extreme Base Station as Extender to Airport Extreme Time Machine

I have tried this a few times, but to no avail: Tonight I purchased an Airport Extreme Base Station (AE) to set up as an extender to my Airport Extreme Time Capsule (AETC). The Airport Utility finds the router and goes through set-up seemingly fine, with green lights on both. Then shortly after (within a minute) the AE reboots on it's own, followed by the AETC rebooting (again, on it's own) and this occurs repeatedly. I reset the AE completely and run through the set-up and the same thing occurs. I've also done soft resets to the AETC. Long and short of it - the restarting discontinues once I unplug the power cord from the AE. Then the AETC resumes as it has - providing fine wifi and speed. It appears the AE rebooting on its own makes the AETC reboot. Any ideas? Thanks!

howto - extending airport 802.11n networks
Pre-Requistites
1) Ensure all have most recent firmware - 7.7.3 for AC devices, 7.6.4 for 802.11n devices
2) Have most recent Airport Utility (OS X 10.7 thru 10.9, use 6.3.2, IOS6/7 use 1.3.3)
3) Only have the Primary Airport/TimeCapsule powered on for now
Set up the Primary/Anchor Airport Base Station
1) Do this over ethernet - ensure that the Modem and TimeCapsule/Airport is connected on the WAN port
2) You'll be prompted by Airport Utility to name the Network and the Base Station
Network is the SSID of the Wireless LAN
BaseStation is the name of the Airport/TimeCapsule
3) You'll be prompted for a password - this will be for both the WLAN and the Base Station on initial setup
Note here - there are at least three passwords to worry about post setup
a) BaseStation Management - in this how-to, this will be carried thru to the extended basestations
b) WLAN Access
c) Disk Access for TimeCapsule and AirDisk
They can be same or unique, up to you...
Configure the Airport/TimeCapsule for WiFi/Network
4) Select the named BS in Airport Utility - click the 'edit' button
5) Review 'Base Station' Tab
5a) BaseStation Name
5b) BaseStation Password - you can change this now if desired, this does not affect WLAN password
6) Review Internet Tab
6a) set as appropriate for your network - e.g DHCP or other depending on needs
6aa) focus here is getting the primary BS set up first
6b) Click Internet Options - this is IPV6 setup - for now...
6ba) Set to Link-Local Only, click save, you can go back and change this later if needed
7) Go to Wireless Tab
7a) Set Network Mode to "Create a wireless network"
7b) Check Wireless Network Name
7c) Wireless Security - recommend WPA2 Personal - this is important as you'll need this later
7d) Wireless Password - the password entered in step 5b above is what is used here, feel free to modify or not - if so, note this
7e) disregard Enable Guest Network for now
7f) Click Wireless Options
7g) ensure 5Ghz network name is unselected
7h) Country as appropriate - since I'm in California, I choose United States
7i) Leave 2.4Ghz and 5Ghz Channels as "Automatic" for now, click save if needed
8) Click Network Tab
8a) if this is your primary router - use DHCP and NAT
8b) Click Network Options
8c) DHCP Lease - I use 12 hours
8d) IPv4 DHCP Range - every here is a bit different, but my recommendation for most folks
192.168.1.100 to 150
Use what works for you, keeping in mind that the AP Extreme, TimeCapsule, and 2012 Airport Express can handle 50 clients, max
8e) Ensure that Enable NAT Port Mapping Protocol is selected
8f) can worry about Enable default host at: [] later, this is the DMZ'ed host
8g) can choose to enable IGMP Snooping or not - doesn't affect the primary setup
8h) click save
TimeCapsule Only - for Airport Extreme, worry about AirDisk later
This is TimeMachine support, along with FileShares
9) Select Disks - you should see a partitiion named "Data"
9a) ensure that Enable file sharing is selected
9b) ensure that Share disks over WAN is unchecked for now
9c) Secure Shared Disks:
Choices here -
device password - noted in step 5b above
disk password - this will be for all LAN clients that can see the Data Partitiion
accounts - you can set up separate users and passwords - this is beyond scope of this how-to
Recommendation if using as TimeMachine only, use a disk password - note this as you'll need it for timemachine on the clients
Save Settings to the Airport/TimeCapsule
10) Click the "update' button
The Airport/TimeCapsule will restart
Everything now should show green and shiny - open a web browser and attempt to go to Apple/Google/Yahoo, to ensure that you've got network connectivity
Reviewing things in the Airport 6.3 utility, you should see your base station and the Internet - both with green status
Once done here, let's extend the Wireless Network
Note - again, it helps to be connected to the primary base station on ethernet, wireless makes things, erm, challenging
11) with another decive - Mac/iPad/iPhone/iPod Touch or PC, ensure that Wireless LAN is working on the primary AP/Basestation
Once this is done, then proceed to the next step
Enable the "Extended" Airport - can be another TimeCapsule, Airport Express or Airport Extreme
For purposes of this discussion - assume all ore 802.11n capable at a minimum, so this applies towards more recent gear
a) Airport Extreme AC (2013)
b) Airport TimeCapsule AC (2013)
c) Airport Express 2012 Dual-Band (Looks like AppleTV)
d) Airport Extreme 802.11n 5th Gen, TimeCapsule 4th Gen
e) Airport Express 802.11n - similar to the 802.11g variant, looks like a MacBook Pro power adapter
Assumptions here is that the extended airport is factory defaults - see link below for more info:
http://support.apple.com/kb/HT3728
Once this is done, plug in the Airport that is intended for extending the wireless network
after about a minute or so, you should see a blinking orange light, this is normal...
In Airport Utility, you should see in the upper left hand, "Other Wi-Fi Devices (1)" - click this, if you don't see this, exit and restart Airport Utility
12) clicking on the button, you should see an entry menu as "Airport Extreme xxxxxx", select this
13) Once selected, you'll see "This Airport Extreme/Express/TimeCapsule will be set up to extend "Primary Base Station"
14) Enter the name for this base station - it should be unique from the name of the Primary noted in step 5a
15) Click "next"
16) Should see "setting up this base station to wirelessly extend..."
you'll see some progress messages.. this is the two basestations handshaking....
If successful, you'll see the BaseStation named in step 14 as "is now wireless extending "base station named in (step 5a)"
STOP - the Airport is now extended, repeat steps 11 thru 16 for each addtional Airport
For advanced features - such as port forwarding, DMZ, IPv6 Tunnels, Back to my Mac, etc - perform this only on the Primary Base station outlined in steps 1 thru 8h
Good Luck!

Is there any antenna for airport express?

I think i´m having problemas with the signal of my airport express and all the readings i made always refer antennas for airport extreme base station.
My question is, if there is any antenna for airport express that don´t needs an extreme base station.
Thanks
Ricardo
Pentium IV Windows XP Pro

Two quick things to check using AirPort Utility on both devices:
On your "main" base station
Open AirPort Utility - click Manual Setup
Click the Wireless tab/label located just below the row of icons
There must be a check mark next to "Allow this network to be extended"
Click Update to save your changes.
If you don't see this option, you likely have an older AirPort Extreme that does not support the "extend" feature. Please clarify on the version that you have
On your AirPort Express
Open AirPort Utility - click Manual Setup
Click the Wireless tab
Wireless Mode = Extend a wireless network
Wireless Name = Same name as your main network
Check mark next to "Allow wireless clients"
Wireless Security = Same setting as your main router
Wireless Password = Same password as your main network
Confirm Password
Click Update to save settings
If you do not see the "Extend a wireless network setting", you may have an older AirPort Express, or if you are sure that you have a newer 802.11n model, try holding down the option key while you click on the selection box to see if the "Extend" setting will appear.
Assuming no major obstructions between the main router and area that needs more wireless coverage, a good starting location for the Express would be a point that is approximately half the distance between the main router and the area that needs more coverage.
As I said, this feature works very well if major obstructions do not come into play.

I am trying to extend my airport extreme signal to another airport extreme can this be done? I have tried several time using the automated set up but it keeps failing... What am I doing wrong?

I am trying to extend my airport extreme signal to another airport extreme can this be done? I have tried several time using the automated set up but it keeps failing... I have selected every possible security/password encryption level... What am I doing wrong? If it os possible where can I find step by step instructions? Please & Thank you!

The challenge with the older round AirPort Extremes are that they are "g" wireless devices.
When you configure them for WDS, the speed on the wireless network is cut in half...and probably will not have the bandwidth required to stream video reliably from either AirPort Extreme since both are affected by the WDS setup.
There is not an "automated" setup for WDS. You have to do this manually on both AirPort Extremes. Unfortunately, it is not an easy configuration and it's easy to make a mistake and hard to recover without starting all over again.
Apple's instructions for WDS are here if you want to give it a try.
http://support.apple.com/kb/HT4262
It is possible that it might work. Keep us posted on your progress
Adding a single AirPort Express will unfortunately not help. You have to have "n" wireless devices at all router points.

Antenna for Airport Extreme

I have recently moved to a larger house and find that my Airport Extreme can no longer provide reliable coverage to remote locations within the house.
I would really appreciate your suggestions for a reliable, reasonably priced antenna that would extend the Airport Extreme's range.
Thanks for the help.

Would the Dr. Bott's ExtendAIR Omni cut my bandwidth in half like a regular expander.
An antenna is a passive device. It's used to focus the wireless signal in certain directions, depending on it's design. It does not however put any additional energy into the broadcast - it just takes whatever energy is being put into it and concentrates that in a specific direction. For omni antennas, the energy that is normally sent straight down and straight up is focused into a horizontal plane, extending the reach of the wireless device horizontally.
With the AEBS, if you can imagine, the internal antenna pattern is a sphere with the AEBS being in the center of that sphere. Omni-directional antennas patterns are more like a donut, extending farther than the AEBS's sphere, but only in a single dimension.
Since bandwidth is dependent on signal strength, the farther you can extend the range of the signal, the more likely you will still have higher data rates farther away from the base station. Antennas, are typically, rated in dBi. The AEBS is pretty much an isotropic antenna, and thus has a 0 dBi...and the Dr. Bott antenna is + 3.5 dBi. The higher the dBi, the more "sensitive" the antenna (in a particular direction.)
On the other hand, boosters can actually increase the strength of the signal being transmitted. The AEBS transmission is around 32 mW. Boosters come in a variety of strengths, typically between 100 & 500 mW.

Any idea on an update on 7.5.2 for airport extreme

Does anyone know if there will be an update to 7.5.2 for airport extreme?

The latest firmware for the Extreme is 7.5.2

Is there an extender for Airport Extreme?

Similar Messages

Maybe you are looking for