Is there any Airport Extreme card diagnostic software?

Is there any diagnostic software, or open firmware commands I can use to track down and diagnose problems with my Airport Extreme card?
Are there any hardware tests that can be performed on it?
At a higher level, is there anything I can do to diagnose problems with connections to an Access Point? (I don't have an Airport base station, unfortunately, I recall there being lots of tools for this).
I've looked in /var/log/system.log, but it's not too helpful - contrast this with the vast amount of diagnostics you get on (say) a Linux system... can you enable some "debug mode"?
Can I monitor received / transmitted signal strength from the card?
iBook G4 ~900MHz Mac OS X (10.3.4) Airport Extreme card, D-Link DSL-G604T AP

Don, thanks for the reply.
In this case, it's not a problem with my ISP, as I can access Internet sites from other systems connected to my wireless/LAN router that are connected on the LAN.
It's not a problem with the wireless side of the wireless router, as I can connect from other wireless systems.
I do have problems where resetting the router is the only cure, but this isn't one of them!
The symptoms I was having on the Mac side were:
a) I saw only grey bars in the signal strength status icon - i.e. useless signal.
b) I clicked it, and did 'Turn AirPort off', then 'on' again - this usually 'kicks' most problems.
c) this didn't result in a good connection - Internet Connect showed that the AirPort Extreme card was connecting to the correct network and base station ID, then disconnecting after a few seconds.
(Similar to that discussed at
http://discussions.apple.com/thread.jspa?threadID=380635 )
It looked like my AirPort Extreme had developed a fault (gone 'deaf')... I opened the iBook, reseated the card, clicked the antenna lead back in, but this had no effect.
At this stage, I was ready to take the iBook into the Regent St. Genius Bar, but out of desperation, re-entered the connection details / WPA personal password in System Preferences.... and it all started working!
So I don't currently have a problem, but would like to know if there is any hardware diagnostic for the card, so I can rule out hardware fault in future.
Regards,
Matt
iBook G4 ~900MHz Mac OS X (10.3.4)

Similar Messages

Is my Airport Extreme card dead?

Hi all.
I suspect that my Airport Extreme card is dead or dying. The purpose of this post is to find out if any of you can advise me otherwise, or tell me how to test it, or point out that I've missed something.
Here's the problem in short: it usually fails to find my network. (It finds lots of others, which are locked or not useful to me). When it does find it, it usually fails to connect. When it succeeds in connecting, it usually drops the connection after a few seconds or minutes. When it succeeds in holding the connection for a short while, it drops it when I sleep the machine.
All of these symptoms are variable: some days it'll find the network fairly quickly, some days it never will.
Why do I think the problem is the Airport Extreme card? Because:
- I can connect to the network with my iPhone, and with two other laptops (one Powerbook, one Macbook). It works just fine for them.
- I can share my Powerbook's internet connection via ethernet (the Powerbook using Airport to connect to the network) and that works just fine. That's what I'm doing right now.
- It's been getting worse for ages now, slowly deteriorating.
Having checked through this post here: http://discussions.apple.com/thread.jspa?threadID=2227197
I reckon
System Profiler gives the following information:
Wireless Card Type: AirPort Extreme (0x14E4, 0x4E)
Wireless Card Locale: Unknown
Wireless Card Firmware Version: Broadcom BCM43xx 1.0 (4.170.25.8)
So, have I missed anything? And, more usefully:
1) Is there something else I can try?
2) If I have to buy a replacement card, does it have to say 0x14E4, 0x4E on it or can I use anything that says Airport Extreme? Having read this page http://support.apple.com/kb/ht3024 I think I can get any Airport Extreme card. Is that right?
Thanks in advance!
Jason

What kind of Powerbook is it?
I doubt the card is at fault. The symptoms you describe are consistent with wireless interference, but given the fact your other devices don't appear to be similarly afflicted, it's possible the card's antenna connections have become dislodged, corroded, or dirty. Re-seating the connection may help.
The only way to test the card is to find another wireless network, ideally one that's out of range of other networks, such as you might find in a coffee shop, library, or hotel, and observe your Powerbook's performance with it. The proliferation of wireless devices is making this task increasingly difficult - the limited electromagnetic spectrum for wireless devices is a rapidly diminishing natural resource.
If you want to try a new card, you must replace it with the one on the support page you referenced.

Airport Extreme card does not see any networks...help!

I have a home network that is working fine - 2 linksys routers with WDS set up... it all works great - an Ibook g4 running 10.3 and has an Airport Extreme card connects flawlessly everyday. As does an old G4 powerbook with an old airport card.
however, I have this dual g4 with 10.4.3 running, and a recently-installed airport extreme card.
When I turn airport "on" it never sees our network. And it doesn't see my neighbors' networks, either, which are also always visible.
I can, howevr, connect via ethernet to the router that is somewhat nearby. that networking is fine...I can get on wired, but not wirelessly.
I've installed the 2005-1 update, and have run Software Update as well to see if there are any other patches/updates necesary. so as far as I can tell, I am up to date.
system profiler says:
Wireless Card Type: AirPort Extreme
Wireless Card Locale: USA
Wireless Card Firmware Version: 404.2 (3.90.34.0.p16)
Current Wireless Network: wireless network not available
and in the extensions section for the airport, it says:
Version: 4.0.4
Last Modified: 11/20/05 9:55 AM
Get Info String: 4.0.4, Copyright © 2002 - 2005 Apple Computer, Inc., All Rights Reserved
Location: /System/Library/Extensions/AppleAirPort2.kext
kext Version: 404.2
Load Address: 0x39738000
Valid: Yes
Authentic: Yes
Dependencies: Satisfied
Integrity: Correct
I am at a loss. Is there anything else I can do before writing off the card as a bad card - or perhaps the logic board is faulty?
I hope there is a simple solution to this. I appreciate your expert help.

Go back and recheck the Airport Extreme card installation. Make sure you plugged the connector for the internal Airport antenna into its socket on the Airport Extreme card itself - and make sure the plug is fully seated into its socket (none of the metal sleave should be showing).

Is there a way to update firmware on airport extreme card to work with "n"?

I have a airport extreme card in my G4 Powerbook and want to know if I can somehow update that card to make it compatible with the new "n" wireless standard?
Even if I can't, should I update the firmware and if so, how do I go about doing it?
Thanks!
Dan

No there is no software update that will give that card 802.11n capability.
Your PowerBook can join an 802.11n network as long as that network is configured to operate in an 802.11b/g compatible mode. You will not get the speed benefits of 802.11n since your PowerBook will be operating at 802.11g.
You may want to take a look at QuickTek's products.

HT3024 after installing airport extreme card into g4 ibook 1.07ghz 512 ram it will only boot to open firmware, any ideas why? please help!

after installing airport extreme card into g4 ibook 1.07ghz 512 ram it will only boot to open firmware, any ideas why? please help!

Hi David,
Have you done a PRAM reset, CMD+Option+p+r...
http://support.apple.com/kb/HT1379
In fact, do 3 in a row, takes a bit of time.
Tried resetting the PMU for PB/iB?
http://docs.info.apple.com/article.html?artnum=14449

I bought a airport-extreme but the software to program only works on Windows 7 to get it to work. Any work around?

I bought an Airport-Extreme but the software to program it only works on Windows 7 and above and I have an XP? Any work around?

Have you tried AirPort Utility 5.5.3 for Windows
You need to have XP SP3 installed on your PC to run this version of AirPort Utility.

I have an imac g4 purchased Dec 2003 runnung OS 10.5.8. It runs fine with airport off, but when I turn airport on it freezes with the black page, "restart by holding power key . . ." I swapped the airport extreme card with the one in my ibook G4 (purch

i have an imac g4 purchased Dec 2003 runnung OS 10.5.8. It runs fine with airport off, but when I turn airport on it freezes with the black page, "restart by holding power key . . ." I swapped the airport extreme card with the one in my ibook G4 (purchased same date and running same OS). No change in operation.
I am running wifi from verizon. Recently changed from mifi2200 to jetpak 4620 in a 3G location. Ibook running fine, desktop freezes. If I can boot desktop in safe mode and get airport turned off in time. then I can reboot regularly and imac runs flawlessly with no wireless.Have run disk utilities and TechTool Pro rebuild etc, but nothing has worked. How do I fine the culprit?

the power logix thing was really sad. apple changed so much after 10.4.8 that there wasn't a viable way to patch the software.
That statement is precisely why I don't believe in blindly updating the OS, especially in a non-standard machine.
We can't expect third parties to support us forever, and it is shameful to break something that works fine, except that we updated the OS....
I think that any upgrade or modification to a machine or the OS greatly increases the risk of trouble or incompatibility with current configuration and "new" system files.
After all, the component or software could only be tested as far as the current OS version when the component or software was released.
Beyond that, we are all "beta testing".
Following a beta tester protocol, and applying updates to a cloned system drive first, is a prudent way to approach updates, and not only for older, heavily modified machines.
After 10.4.8 and moreso with Leopard, the focus is primarily on Intel architecture, not PPC architecture.
Like it or not, we are all updating to the abyss of the extinction of our machines, unless we can be satisfied with the last stable version of OS that works well with our hardware and software.
I wish they would include the latest pkgs at least with software update.
Yes, having individual packages, rather than lump "OS X 10.x.x" updates would be nice.
This way, one could update as one sees fit. That is to say, for example, fix the Quicktime, but leave my Network alone, etc., etc.
In all fairness, Apple does provide for some breakdown of updates, but I believe there is much room for improvement, especially, as you point out, with regard to the core services portion of the OS.
Until then, I'll leave Software Update disabled.......

Dead Airport Extreme card?

For the last three days I have had issues with my G5 dual 2GHz and OS X 10.4.2, the latest updates to Airport software and firmware.
The signal strength meter in the menu bar or in Internet Connect is greyed out and the connection cannot be made -- eventually it gets to the point where the G5 cannot even remember any of my precvious connections. The Macwireless.com widget shows the connection and signal strength as bouncing from 0 to about 70% for all connections that are still recognized, with each location bouncing from the top of the list to the bottom and then sometimes disappearing altogether. After a short while the locations don't reappear... Once they're gone, they're pretty much gone without a trace (Airport Admin either cannot connect to the Airport, telling me an error occurred while trying to access it, or it doesn't see anything to get an error message from).
My G4 sits right next to the G5 and has shown no problems. Strangely, after a full day trying to troubleshoot this, the G5 started up today at full signal strength -- I'm using it now to write this message! Nothing has changed on this machine in the past week, except for me trying to get the Airport Extreme Card to function as it had for the month or two I've had it. Yesterday I lost connection altogether -- neither restarting the Mac nor a full shut down, wait a minute or two, restart would restore my connection. At one point, I shut down the machine for about an hour while I reseated the AE Card and let the computer become room temp (roughly 70 F). Still no go...
After eliminating all the variables I could think of, I've come to the conclusion that the Airport card is probably bad -- possibly malfunctioning with heat build-up (?). Problem is, how do I show this problem to a tech? Especially since it's a half-hour drive to the closest Apple store and longer to a third-party Apple repair shop. And knowing that once it's been off for a while and is on a workbench, it will behave like all intermittently faulty equipment and work perfectly. :-/
If anyone has trouble shooting suggestions, or can help me determine for sure that the card is the problem, please help!

Hi Julia,
Well, the card may have problems too, but I now think there's a software problem as others have suggested. It's odd because everything seemed fine for some time after applying the updates, so it appeared as if the card was bad or going bad. For me, I spent three days trying everything I could, including removing and re-seating the card, antenna wire and antenna, trying various configurations, resetting the Airport itself and so on. All to no avail.
On the last day, I had the strangest situation, where Mail could not see the Airport and could connect to nothing, but Safari was able to access the Internet! I used Safari to access sites I hadn't visited in months just to be sure I wasn't seeing cached versions of the pages... Eventually though, Safari lost contact, and that was it for the day.
After all that, the next day I turned on the Mac to see a solid connection that's been stable ever since except for the incident in my previous post where the Airport widgets knocked the connection out. Turning off those Widgets and closing Dashboard brought the connection back up immediately -- I haven't tried them again, and probably won't!.
Once I had the solid connection, I used Onyx to repair permissions, optimise the System and to empty the Network cache. I also deleted the various Locations I'd set up in the Network Preferences to get it back to just the one connection to choose from. If you're comfortable with Onyx (or Cocktail or one of the other utilities) you could try at least clearing the cache(s) and repairing permissions.
Have you tried a complete shut down and leaving the computer off overnight? Do you have anything set to open on startup that may try to connect with the Internet (like Mail or Safari)? Try removng them from your Startup Items (you can do this from the Dock -- click and hold on the icon and a mini menu should pop up with that option).
Have you looked at the info in System Profiler, and does it show the Airport card? (you can access System Profiler from the About This Mac item in the Apple Menu and clicking the button: More Info...) The card should show up under Network>Airpport Card.
Since you have a Powerbook, you have the option to take your computer to an Apple tech (Apple Genius at an Apple store, or to a dealer with a repair crew) and have them troubleshoot it. My guess is they'll end up reinstalling your OS and/or replacing the card... My G5 is far too heavy for me to throw it in the car -- and I found out the hard way yesterday that my computer is just 2 weeks out of warranty, so I'm ineligible for AppleCare. grrr... (my fault, but grrr...)
Let us know if anything good happens -- best of luck!

Is my Airport Extreme Card faulty?

Hi all,
I have an iMac G4, 1Ghz machine. I got it second hand and I have no problems using it, except trying to fathom out if there is something wrong with the mac, or the airport card I have fitted.
I'll try and describe the issue best I can, please bear with me.
The Airport Extreme card is fitted correctly, it is slotted right in and unless I take a hammer to it, it will not go any further. The aerial is also fully fitted, again, it won't go any further.
However, the iMac does not detect the card correctly. If I look in System Profiler, nothing appears under Network/Airport Card. There is no wireless network indicator along the top next to the volume icon etc, and nothing within Network to indicate it is detected either.
But.....
If I look under System Profiler / Hardware / PCI Cards then I discover it. It is listed as Type: Other Network Controller, and crucially, Driver Installed: No. I can supply various ID's as and when required if necessary.
What I am trying to establish is, does this mean there is a fault with the iMac, or with the Airport Extreme card itself? I am looking for some pointers and will gladly check the obvious if required so any hints or tips would be gratefully received. The system is fully updated, and everything else works perfectly.
Thanks for any and all help in advance,
Chris

Hello, and welcome to Apple Support Discussion forum!
You may have to see about getting another AirPort Extreme card
and check that against the results of the first one; and hope the
faulty matter is with the first card and not the iMac G4 itself.
Sometimes, when an AirPort card is not physically present in a
Mac, and was not there during the OS installation, some of the
drivers may not have been installed or installed correctly. Not
sure in this case, if the whole OS including AirPort support is an
automatic function - even when or if there is NO AirPort card in
the computer during the OS X install. +This may not be the case.+
There may be another answer, in this; if the card driver was only
installed IF there was a Card present. Or, IF the driver is installed
even when no Card was in the computer at the time the OS was
installed into the computer. (Some users did note an issue, in a
few instances, years ago.)
It is possible the AirPort Extreme 802.11/g card could be defective.
The other basic possibility could be debris in the card's slot, in such
a way as to not allow all the connections between the card & the Mac.
Be sure to not handle these wireless cards, or for that matter, RAM
memory cards, etc by the electrical contact side of the chips; since
a static charge by handling them, can short out their components.
You could try your luck with a USB wireless 802.11/g module to see
if that may give you wireless access via a USB port, if the AirPort
Extreme card and slot don't act correctly even with a second card.
On rare occasion, there could be an instance where the card may
be OK and not show correctly. Not sure if resetting the Power
Management Unit (PMU) could be of help in this specific matter.
• Resetting the iMac (Flat Panel G4) Power Management Unit (PMU)
http://support.apple.com/kb/HT1712
{The older AirPort Original 802.11/b wireless card would not fit into
an iMac G4 computer with the 1.0GHz or later (1.25GHz) processor
so that should not be among the considered possible issues, here.}
Hopefully, the issue is only dust in the Card's slot; which would be
comparatively easy to clear out. Or the AirPort Extreme card itself
could be bad. So, these are the simplest and least costly items to
take into consideration and check, compared to a logic board.
And it is possible to use a USB wireless adapter or module for use
with the iMac G4 and 802.11/g/n so long as the specs are correct
for the computer hardware and be sure the USB plug fits well. As
these generally go, they can be as easy as automatic recognition
by the computer. If you go this route, try the item without any new
software installed to support the USB wireless first. It may just go.
If the AirPort card were tested in another computer, to be good,
then perhaps to put the card back into your iMac G4 1.0GHz
machine and reset the PMU, check the computer's Profiler; and
maybe see if by reinstalling the Leopard (10.5) last Combo file
(10.5.8) over the top of your current 10.5.8 system, could help
it recognize the AirPort extreme card that was not there during
the installation of OS X 10.5.8 Leopard. This is a stretch.
Good luck & happy computing!
+{edited to add conjecture and other stuff}+

Airport Extreme Card - USA version not compatible with Europe?

I'm having some problems with the Airport Extreme Card in my Mac Mini i.e. my connection to the internet is mind numbingly slow when using it. I have no issues when I hook it up directly with a LAN cable and I've used a friends Macbook to connect to the wireless router and their connection works perfectly.
My specs...
AirPort Card Information:
Wireless Card Type: AirPort Extreme (0x168C, 0x86)
Wireless Card Locale: USA
Wireless Card Firmware Version: 1.4.3.1
Current Wireless Network: SpeedTouch3C84E7
Wireless Channel: 11
Now here's where I think the problem lies, I bought this machine in the US but am now living in Belgium...you'll note that the card locale is set to USA. My friends machine has a card locale of worldwide and I think this difference is causing the issue. I found another thread that mentions using a USA card in europe limits the number of available channels but I'm still in the dark as to what to do about it.
Is the locale changeable via a software setting or is the hardware different...maybe there's a firmware change I could make?
If it's hardware is this something my Apple store can switch for me?
If I'm really stuck can I switch my router to the US settings to fix the issue?
Any other ideas?
Thanks for the help!
Chris

hi. I think that the only difference between USA and worldwide cards is that ww cards have additional channels (12 and 13). You should be able to use your mini in Europe.

20-in Intel iMac (early 2006) Tiger -- configuring Airport Extreme Card

Hi -- I come from a mostly "not mac" background and am having difficulty diagnosing a slow internet connection -- and can't tell if I'm trying to use the right tool for the job. (I am using MAC OS X 10.4.11)
My home network uses a Linksys WRT54G wireless router and I've got 3 computers that connect using the router (including the iMac) -- the other two are Windows-based machines. We've got a 2-story house and I've been moving the router and computers around the house a bit trying to come up with the best configuration for a good wireless connection (I'm going to be ordering a supplemental antenna, but don't have it yet).
The two Windows machines (one using a relatively old PCI wireless card) get strong signals. I'm not even sure how strong a signal the iMac gets as I am not sure which utility allows me to see this. I do know that it has a painfully slow connection speed (at least web pages load at a crawl...).
I've got an Airport Extreme Card (0x14E4, 0x89). Firmware: Broadcom BCM43xx 1.0 (4.170.46.9).
I went to Apple's support downloads, and attempted to install firmware updates, but I am getting a message that indicates that these updates are not applicable to my card. I updated the Airport Utility software, but as far as I can tell that utility is looking for an Airport Extreme base that I don't have. Other than that I haven't seen any applicable information using that utility.
I was hoping to reach a configuration area that would allow me to specify 802.11b or g, and allow me to specify the channel -- but other than in the internet sharing section I don't see a place that allows me to do this. (I've currently got our home network on a 802.11g network on channel 8.) We're using WPA personal encryption -- which does appear to be recognized by the Airport Extreme card.
Am I missing something? I've got 3 "Airport" utilities but none of them seem to allow me to specifically configure the internal card. I've gone to "network" under System Preferences, and although I can see a "configure" button when I click on "Airport," it's pretty basic and doesn't allow me to set the channel or anything other than encryption & a password.
I would appreciate any help you can give me. Is this card so outdated that I should invest in a newer one? Am I limited by my outdated OS? (I hesistate to upgrade OS's when things are working -- in the Windows environment at least newer isn't always better...) Thanks. mcaren

Thank you Duane for your response.
I have only noticed a huge difference in the connection speeds of my iMac and our other computers in the last 6 mos. to a year. I did notice an improvement in speed when using a Rosewill USB wireless adapter -- I had a good wireless signal but would intermittently lose connectivity (and their user support was basically nil...).
I can't tell if I'm actually seeing an improvement in our other machines' connection (perhaps from the tweaking I'm able to do) or if in fact the iMac is slowing significantly. I think it's the latter. I've actually swapped out machines in the same position to see if location is at fault -- and I get no improvement in connection speed. I've had the iMac connected with ethernet to our router when possible because it has had such a slow wireless connection, but I needed to move the router recently and would like the iMac to stay in another room.
I've also read a lot about connection speed issues with Airport, but these reports are usually blamed on Leopard updates (there might be similar Tiger issues, but I don't read about them...).
Oh well. I'm hoping someone out there has some tricks up their sleeve as to how I can improve my wireless connection speed. Thanks for the help! mcaren

Airport extreme card firmware update?

I have a Powermacg5 with an airport extreme card in it. I have been trying to see if there was a firmware update for it (currently 404.2 (3.90.34.0.p16). I can find the firmware update for the extreme base station but nothing for the card. I tried to see if the update for the base station would work for the card, it does not even recognize the card.....
Any suggestion?
Thanks
Frederic

apple lists available airport software/firmware here...
http://docs.info.apple.com/article.html?artnum=75422
your airport card is running the same firmware as mine, i believe this is the latest available release
base stations do not run the same firmware as cards, a base station updater won't recognize cards
if/when there is an update available, it will show up when the osx software update check runs

Airport Extreme Card is weak

I have 2 questions. First, is there a firmware upgrade for my Airport Extreme card version 405.1? Now to my main question. Is there a reason why after 2 years of working perfectly that my wireless connection has gotten weak? When it was working correctly, I had a good connection from the other end or my house. Now I don't even hold a good connection across the room, about 10'. This is with an Extreme base station. I also tried a linksys connection while visiting family in North Carolina and I had to sit right by it to get any connection. Do these cards occasionally go bad? Thanks for any help.

jerryg233, Welcome to the discussion area!
First, is there a firmware upgrade for my Airport Extreme card version 405.1?
No that is the latest. All firmware updates are downloaded automatically when AirPort/system software updates are installed. There is no user notification nor notification.

Disable my airport extreme card

hello all. i have recently bought a WN825 pcmcia card for my powerbook g4. It has a broadcom chipset so when plugged in it tricks the airport software into thinking its an airport extreme card. The problem is having two wireless cards connected at the same time causes a conflict and i often get problems when booting up.
naturally, i have tried to disable airport via the main tool bar but it also disables the pcmcia card. i basically need to disable the airport extreme card but keep the airport software running so that it recognises my broadcom third party card. (recognised as cardbus). i have also tried to disable port config in prefs, but again this disables airport completely.
i have searched discussions and found only 1 archived post on this which didn't help. there must be a way of doing this?
any help much appreciated.

Here you go:
If you have an original Airport card installed and don't want to remove it, go to:
/System/Library/Extensions
Rename the following files by adding the suffix ".disabled" to each:
AppleAirPort.kext
AppleAirPortFW.kext
Remove the following kext cache files:
/System/Library/Extensions.mkext
/System/Library/Extensions.kextcache
Reboot.
The above is a summary. You must do this in a Terminal window and you must use sudo thusly:
sudo tcsh
Password: <<yourAdministratorpassword>>
cd /System/Library/Extensions
mv AppleAirPort.kext AppleAirPort.kext.disabled
mv AppleAirPortFW.kext AppleAirPortFW.kext.disabled
rm Extensions.mkext
rm Extensions.kextcache
<Control-D>
Close the Terminal window
Reboot.
Caveats: You could screw up a lot of things easily if you do anything else while root in a Terminal window. BE CAREFUL.
Remember, it's YOUR PowerBook G4, not mine and hence your risk.

Airport Extreme Card missing after Leopard and Login & Keychain Update

After these updates the network prefs showed no Airport card installed, even though it had been there seconds earlier. This was buried at the bottom of a posting for a similar problem. Just wanted to make it easier for others to find.
"I'm having the same issue with an iBook G4 1.2Mz model. Having successfully installed Leopard (5 user license version) on my Macbook, I installed it on the G4. At first this worked until software update installed Login & keychain update 1.0 and Remote desktop client 3.2.1. When the iBook reset the airport extreme card wasn't there. The icon in the menu bar states No Airport card installed."
"Some users have determined that an artifact left over from Mac OS X 10.4.x interferes with wireless connections after Mac OS X 10.5 is installed. The issue can be dealt with by finding and removing the AppleAirPort2.kext file from your Extensions folder, located here:
Macintosh HD:System:Library:Extensions"
That fixed it for me.

Ezz wrote:
Ok, I just installed the Login & Keychain update 1.0 from the software update and after rebooting my Airpot card does not get recognized anymore. This really ***** Apple!
Anyone else encountered this problem? Any known solution yet?!
Message was edited by: Ezz
Judging by the amount of posts it must be isolated. Mine works fine. Did you repair permissions ?
" Keychain-Administration or Privilege Issues after Upgrading to Leopard:
If after installing Leopard as an upgrade or archive and install you experience any issues with not getting mail, can't run Disk Utility, can't login as administrator, can't print or anything that entering existing User name and/or passwords requires, you are not alone and Apple is working on it now.
The fastest method of determining if you have been bitten by this, open System Preferences, click on Accounts and verify that you are the Administrator as opposed to Standard, and that the checkbox asking if you want this user to be an Administrator is checked. If you are Standard, and the box is unchecked and/or greyed out, you have a situation most likely, whether you know it or not, yet.
Further verification can be done in the Accounts window by clicking the lock to make changes, entering your name and password and being denied access.
Apple says the best thing to do right now is not to try too much voodoo and wait until later today for a solution, hopefully. I was told to close the lid and walk away until Apple calls me back.
The good news as I write this on my old reliable Pismo, is that I have a bootable Carbon Copy Cloned 10.4.10 complete back up on an OWC external FW disc. Thanks Mr. Bombich! I just hope I don't have to use it.
Post from xlr8yourmac.com
William

Is there any Airport Extreme card diagnostic software?

Similar Messages

Maybe you are looking for