Is there any labview drivers for Spirent 5500 wireless channel emulator

Spirent 5500 currently doesn't have GPIB capability despite the connector on the rear panel. It is controlled via .net from a laptop. Labview drivers needed.

Clarification:
National Instruments would like to receive driver requests for all instruments that do not have drivers available on ni.com/idnet. Each request is being added to our instrument driver request database and considered for development. We try to develop instrument drivers according to popularity. Unfortunately, we cannot develop instrument drivers for all the requests we receive.
If a customer would like to try developing his/her own instrument driver, we have documentation, model instrument drivers, and driver templates to help him/her in development. This information can be found on our web site: http://www.ni.com/devzone/idnet/development.htm
Thanks,
Instrument Driver/IVI Group
National Instruments

Similar Messages

  • Are there any labview drivers for the chromalox 2030 controllers?

    I am looking for drivers to communicate with the 2030 chormalox environmental controllers.  I haven't been able to find any.

    I never did write anything for the Chromalox...lightning end up zapping it and we replaced the Chromalox with a Watlow. Check out the Product Instruction Sheet (PDF) at the link below. It's pretty basic, but might be enough to get you going. If not, I'd shoot an email to Chromalox and ask them if you have any communications manuals for it.
    http://www.chromalox.com/products/prodinfo/en/2030.html
    -- Jason (Matt)

  • Are there any JDBC Drivers for SQL Server 2000?

    Hello Everyone,
    Any news on the JDBC drivers for SQL Server 2000? I know it is not
    certified yet but is there a date when it will be.
    Which versions of WLS will they work with? Any help is appreciated.
    Sincerely,
    --Luis

    Hello Michael,
    Any news on the JDBC drivers for SQL Server 2000? I know it is not
    certified yet but is there a date when it will be.
    Which versions of WLS will they work with? Any help is appreciated.
    Sincerely,
    --Luis
    "Michael Girdley" <[email protected]> wrote in message
    news:3a6549bb$[email protected]..
    Not yet, but they will appear on the web site in about two weeks.
    Thanks,
    Michael
    Michael Girdley, BEA Systems Inc
    Learning WebLogic? Buy the book.
    http://www.learnweblogic.com/
    "Stefano Picozzi" <[email protected]> wrote in message
    news:[email protected]..
    Are there any JDBC Drivers for SQL Server 2000 for Weblogic Server.

  • Does anyone out there have LabVIEW drivers for either a Z-Mike 1102 (Beta Lasermike) or a Compumotor 6104 (Parker)?

    Does anyone out there have LabVIEW drivers for either a Z-Mike 1102 (Beta Lasermike) or a Compumotor 6104 (Parker)?

    CompuMotor creates a Motion Toolbox for LabVIEW, but it is not supported by National Instruments.
    You can find some support files and downloads for the 6104 from http://www.compumotor.com/support_samples.htm

  • Is there any LabVIEW driver for the Agilent 53147A counter/power meter?

    I am trying to find a LabVIEW driver for the Agilent 53147A counter/power meter, but I cannot find it. Is there any?

    NI does not have a driver and a quick check with Agilent shows that they don't have a driver either.
    You can go to http://www.ni.com/devzone/idnet/ and request a driver. You will also find links on how to create your own driver. Your other option is to use the Instrument I/O Assistant.
    p.s. In the future, you should use the Instrument control board for posting questions. this board is for NI counter/timer products.

  • Are there any current drivers for the LaCie 324 monitor

    subject line...
    LaCie's website has nothing beyond 2008

    thanks. appreciate any help thrown my way.
    When I mentioned that there was a choice of either 2 different HDMI or a DVI output from the HD Express, I have not tried to use the DVI output. I would need a HDMI to DVI adapter which i may order. Thing is, I don't always want to use the LaCie 324 as a video reference monitor. I also like using it as a standard or second monitor with OSX and other software. This means I would always have to be switching DVI connectors every time i wanted to use the 324 in a different configuration. Bummer, but doable i guess. Here's some info from the MOTU site;
    What are the system requirements for the HD Express?
    System Requirements for the HD Express
    The HD Express has the following system requirements:
    Available PCI-Express x1 slot or ExpressCard/34 slot
    Large hard disk drive (preferably at least 500 GB)
    CD-ROM disc drive for installation
    For Mac OS X:
    Multi-processor or multi-core Intel Mac
    1 GB of RAM; 2 GB or more is recommended
    Mac OS X version 10.5 or 10.6; v10.5.7 or later required
    For use with Final Cut Pro 6.0.5 or later; Final Cut Pro 7.0 or later is recommended on Mac OS X v10.6
    For Windows:
    Intel Core 2 Duo, AMD Phenom II, or equivalent 64-bit processor; multiple processors or multi-core processor required
    2 GB of RAM; 4 GB or more is recommended
    Windows 7 or Vista, 64-bit versions only; Vista SP1 or later required
    For use with Adobe Premiere Pro CS5 or CS5.5; version 5.0.3 or later required
    And here too;
    MOTU.com - HD Express Overview
    So, I am still waiting to hear back from MOTU tech link about this issue And as I said before, my guess is that the PCIe card they sent with the HD Express has a large bug or is just completely inoperable.
    Thanks again- J.

  • LabVIEW Drivers for Instruments on DIN-Messbus

    I'm trying to interface to a group of instruments supplied by Rabe Messtechnik in Germany. They are networked through the DIN-Messbus protocol. Are there any labVIEW drivers for the following instuments or the protocol itself?:
    PPM-60, PIT-1500, PDM-02, PWS-02, CIO-26, PNC-02, PSW-02.

    Unfortunately I was unable to find a driver for this instrument. Instrument drivers can be found on our website
    www.ni.com/idnet
    by searching for a specific instrument name.
    If you cannot find the driver by doing this, then you have couple of options. First, I would like you to submit a request for this driver at:
    http://www.ni.com/devzone/idnet/other.htm
    We develop drivers based on demand and popularity so the more requests we have for it, the greater the possibility that we will develop one.
    If you would like to try developing your own instrument driver (or modify the existing one), we have documentation, model instrument drivers, and driver templates to help at :
    http://www.ni.com/devzone/idnet/development.htm
    We also have a syndicat
    e of third party vendors that specialize in National Instruments' products and services. Some of the vendors specialize in driver development. I would suggest contacting one of the Alliance members at:
    http://www.ni.com/alliance
    I hope this helps.
    Kim L.
    Applications Engineering
    National Instruments

  • Are there LabVIEW drivers for the MCC USB-501 temperatur​e logger

    I am looking to purchase the MCC USB-501  and use it to acquire the ambient temperature on an event driven basis. The data logging portion is something I am interested in, I just want to have my application acquire the tempture when a certain event occurs. Does anyone have any LabVIEW drivers for this device?

    I don't know what you mean by using a logger that collects data on an "event driven basis".
    It is nifty little device, but it basically does one thing.  It logs data.  You load the software, configure it for when to start an how often to log data, unplug it, and put it where you want to log the temperature.  When you're done, you get it plug it back in and download the data that was logged.
    There is no way to configure it to react to events.  It's possible that a LabVIEW driver exists for this, but all it would do is provide an alternate way of downloading the data instead of using the software that comes with it.  It is not an immediate or interactive piece of hardware like a normal data acquisition card would be.

  • LabVIEW Drivers for Norma 5155 power analyzer

    I have several questions concerning a GPIB LabVIEW driver for the power analyzer NORMA 5155 (NORMA is now part of LEM company):
    1- Has anybody programmed a driver specially for this device so far ?
    2- Is it possible to use other similar drivers (LEM/NORMA 4000..6000) for it?
    3- How would you approach building a suitable driver? (Instrument I-O Assistent ...,)?
    Any answer could be helpful.
    Andreas, Germany

    1) There are no drivers for the 5155 at http://zone.ni.com/idnet97.nsf/browse/
    (but perhaps someone beside NI has programmed a driver)
    2) The same type of instrument from the same company will likely have a similar command set. The drivers for the 4000 and 6000 are Plug and play driver and not IVI drivers, so modifying them would be easy.
    3) I would first call LEM tech support and ask what the difference between the commands sets of the the 5155 and 4000/6000 are. If LEM tech support is unable to give a good answer, then I'd try to get the manuals for the 5155, 4000, and 6000 to just compare the command sets myself. If they are very similar I'd just modify the old driver. If they are very different, I'd just make I/O assistant VI for each function in th
    e manual, and I would have a low-level driver. Once you have this low level driver you can just combine functions to make higher level VIs.
    Hope this helps!

  • Any labview example for resonator parameter measurement?

    Hellow!
    I am doing the measurement of the resonator parameter(like C0,L,C1,R) using network analyzer, are there anybody has some experience about it, are there any example code? thanks a lot!
    Mike 

    Mike,
    Which network analyzer are you using.  You may be able to find some LabVIEW drivers for it at the following link:
    National Instruments Instrument Driver Network
    You may also check the other thread you started and the responses from JL Chew.
    Network Analyzer
    Hope this helps!
    Andy F.
    National Instruments

  • Labview Drivers for an Integral Tech Framegrabber

    My company is interested in purchasing a video inspection system that
    uses the following frame grabber:
    http://www.integraltech.com/art/downloaded%20from%20current%20site/fbmv/documents/fbmvlitespecsheet.pdf
    Integral Tech does not make Labview drivers for this card.
    Would there be a way to get these written, or would that be cost
    prohibitive ?
    Thanks for any suggestions.
    Rick B.
    Email: Use Yahoo instead.

    Hi Rick,
    I'm not really sure whether this is what you're thinking of but...
    Since INTEGRALTECH provides a VFW driver for their frame grabber you could,
    e.g., use this tool from aNI server:
    http://exchange.ni.com/servlet/com.quiq.servlet.GetObject/lv_vfw.zip?KEY=101
    ..97.12134.14&SIG=101.97.12134.14&EXT=mime:application/x-zip-compressed
    It works very well but, like any VfW based application, has the disadvantage
    of being able to read out only one camera at time. If you plan to use
    multiple frame grabbers simultaneously you have to find a different
    solution.
    It should also be possible to call the DLLs INTEGRALTECH provides from
    LabView.
    Best regards
    Arno
    "Rick B." schrieb im Newsbeitrag
    news:[email protected]..
    >
    My company is interested in purchasing a video inspection system that
    > uses the following frame grabber:
    >
    >
    http://www.integraltech.com/art/downloaded%20from%20current%20site/fbmv/docu
    ments/fbmvlitespecsheet.pdf
    >
    > Integral Tech does not make Labview drivers for this card.
    >
    > Would there be a way to get these written, or would that be cost
    > prohibitive ?
    >
    > Thanks for any suggestions.
    >
    >
    > ---
    > Rick B.
    > Email: Use Yahoo instead.

  • LabView drivers for Agilent 54830B scope or E4402B Spectrum Analyzer?

    Where can I find LabView drivers for the Agilent 54830B scope and the E4402B spectrum analyzer, or at least a driver for another instrument in the same families that I could modify? There are none on the NI site or the Agilent site.

    One thing that I have done several times is get a LabWindows CVI
    driver from Agilent. You will be provided with a .fp file. LabVIEW
    has a link under the Tools>>Instrumentation menu that allows you to
    "Import CVI Instrument Driver." This will take the function calls
    from CVI and build a set of VI's with the same name. The vi's will be
    wrappers for a dll that is used by CVI and other text based languages.

  • LabVIEW drivers for Agilent Noise Source 346B and Signal Generator E8257C-520

    Could anyone please tell me where to find LabVIEW drivers for Agilent Noise Source 346B and Agilent Signal Generator E8257C-520. I did not find them on NI's web site. Thank you!

    To my knowledge, the Agilent 346B Noise Source is not a programmatically controllable instrument and therefore we can't create an instrument driver. I suppose it is possible to be controlled through an instrument (like the PSG) but I don't see any documentation on this.
    As for the E8257C, we are insterested in providing a LabVIEW driver for this instrument series. Let me know if you are interested in assisting our development effort by loaning us the instrument.
    Jason Hobbs
    Instrument Drivers

  • Labview drivers for Prisma QMS

    Hi,
    I'm looking for labview drivers for the Prisma Quadrupole Mass Spectrometer
    from Pfeiffer Vacuum. If possible also a simple rest gas analysis (RGA) VI.
    Can anyone help?
    Hans Rosink

    There is no driver available as the qmg220 uses OPC communication you can use labviews build in OPC functions.
    But the problem is that the "normal" labview OPC functions using datasoket are a little bit limited and when you need to adress many OPC items it may crash.
    Therefore NI is producing the LABVIEW DSC module which is avialable for extra money and with the main problem that you are not able to build stand alone applications without any extra licencing costs. Which makes problems if you want to sell your software or add it to the instrument you sell.
    On the other side the DSC module is a little bit to powerfule for the communication with the QMG220.
    Because of these arguments we decideed to use a OPC developement toolkit from Softing . 
    We started with the .NET developement but there4 was a reasonable memeory leak in Labview when using .NET event callbacks.
    This has been solved with Labview 2009f2 and up versions.
    Up to now we have made our communication with the Softing ActiveX control within labview.
    Now we are on the  point to switch bak to .NET. 
    When try the OPC connectivity from any third party opc API vendor and you are using a remote OPC from labview please tonst forget to add the line.
    ole.AuthnLevel = 1 to your labview.ini file. 
    Hope this gives you a first overview.
    We are not planning to build a easy to use driver for the QMG220 but we build a lot of vi's to control some functions and collect the data.
    Best regards
    Gernot 

  • Labview drivers for keithley DAS 1600

    hai all,
    I am searching quite for a long time for the Labview drivers for my Keithly Metrabyte DAS 1600 data aquisition card. Could any body provide me some weblink or some source from where I can download the drivers.
    thanks in advance.
    email:[email protected]
    nanda

    Dear Nanda
    Thank you for choosing National Instruments!
    National Instruments provides drivers for NI products only. If you need drivers for other third party hardware, you will need to contact the hardware manufacturer for the drivers and VIs to interface with LabVIEW. You can go to the download center for Keithley from this link and typing in DAS 1600 in the search page. This will bring up a section with downloads - wherein you can find driver updates. If you do not find information here, then you may need to call in tech support for Keithley to get the drivers.
    Hope this helps.
    Thanks and Regards
    ShekharS
    National Instruments

Maybe you are looking for