Is this a new variant of the 'grey screen, won't boot' problem?
Hello all. My second hand Powerbook G4 starts, the bitten apple comes up, then there is no further boot up action. The situation leading to this was as follows;
- firstly, starting but going to a blank/grey screen and staying there. The new variant alluded to, which I have not been able to find referred to, was that at this stage, one could for a while, actually type letters (coming out in white). After a while this stops.
- researching this problem here I followed the advice in the Grey Screen article - http://support.apple.com/kb/TS2570
one on resetting the PMU - http://support.apple.com/kb/HT1431#faq11
and on using Target Disk Mode - http://support.apple.com/kb/HT1661
None of this helped in the slightest with these symptons.
Because I was away on holiday at the time I did not have access to system disks, or actually using Target Disk Mode. On returning I used TDM to successfully connect to the PB, and it became evident that there is a drive problem. I had taken quite a few edited videos with me and it was possible to copy some off, but not others. Data that refused to copy always led to having to restart the machine because the 'copy' mode would refuse to cancel. I also reinstalled the OS, and using another PB used TDM to allow Diskwarrior and Disk Utility to work on the poorly machine. Both were able to do some work, but not complete all their tasks. The SMART, so called, diagnostics always came up fine.
Now if I turn it on the grey screen stage is not reached, the apple symbol comes up and stays there, with no spinning wheels.
So, is there anything else I can do?
Is the grey screen with some typing possible relevant or interesting in any way?
Thanks!
Stephen
Hello,
It's possible to have two Mac OS X's installed on one drive.
Have you tried this:
Restart whilst holding down Command-S
The screen should turn black and load some text
At the prompt type
fsck -fy and press Return
Hopefully some repairs will be performed.
At the prompt type
reboot and press Return
If that doesn't provide any help then try starting in safe mode.
http://support.apple.com/kb/HT1455
Once in safe mode, you can set the startup disk and reboot.
If that don't help, then all I can suggest is a clean install of the OS.
Using a Mac OS X install disk either retail or for a PowerBook G4, boot and upon selecting the destination drive, select option, then erase and reinstall.
A fresh install should resolve this problem as a last resort.
Best of luck, let us know how you get on.
Similar Messages
-
I recently recieved a macbook that I was told was broken. She didn't know what was wrong with it, but she told me I could keep it if I wanted to get it working again. Its http://support.apple.com/kb/sp579 this model. I got the laptop to power on, but the apple logo and the spinning wheel under it kept spinning forever. So with me and my "Amazing" knowledge of Macs, I thought it would be best to reformat the drive on my PC via sata cable to FAT32 (which I was told is a format that mac devices can read/write on) and install OSX from usb. So I have a .dmg file and used TransMac to format the usb and make the usb drive bootable with the .dmg.
I formatted the drive to FAT32 and plugged it into my macbook and I get a folder and a question mark blinking on the screen. After looking at some forums online, I found that the error occurs when you don't have the correct filesystem to boot or something along those lines. So I try rebooting the computer while holding C, to boot from an external device (such as USB). Nothing. Again the folder and question mark blink on the screen. I look at some other boot option keys and try all of them. Shift for recovery mode, D for apple hardware test, Control, option, P, and R for resetting NVRAM and PRAM. Everything! The only things that differ slightly are when I press Option for startup manager, N for NetBoot and Option+N for internet default boot image. When I press N and Option+N, I get a blinking globe for about 5-10 seconds and then the folder and ? blink again. When I hold Option for the startup manager, I get a white screen and my curser, which I can move around the screen, but there is nothing to click on, its just white.
Currently I have a USB flash drive plugged into the macbook with a .dmg OSX installer on it via TransMac and for some reason, my macbook doesn't want to try to load it. Either I have the wrong file format for the installer, or my macbook is having problems. I read that the hard drive may be the problem, except I can use it on my PC so I know that it works fine.
If anyone has any information about how to fix this, or any ideas. Please let me know! I would very much like to get this macbook going again.The correct format for Mac OS X is not FAT-32.
As the computer shipped with an install-restore disc DVD set that could be used to start the computer as an emergency disc and use the Utilities on the Installer, without running the Installer itself, to format, attempt repair, and perform a few different system installs or reinstalls, this is where the correct format would come from.
Was there documentation to confirm the build year and model information, such as to refer you to the product page link you posted above?
If accurate, that MacBook shipped with this custom grey
install-restore DVD version of Snow Leopard:
Original OS
Mac OS X 10.6.1 (10A2047)
Maximum OS
Latest release of OS X
AirDrop
Supported
Hardware Test
AHT 3A181
And to be able to restore the basic OS X to that level, official replacement discs for that computer should be ordered from AppleCare; to facilitiate obtaining correct ones, you should find the product serial number. There likely would be a fee involved. The replacement disc set may have a different number than the one in the information box above, but would match the hardware series by Apple standards. And a replacement disc may not have the original extra applications that shipped with the computer when new. Those original discs are part of the retail computer, an essential part number, like the power adapter, and should be included with the computer even after an OS X upgrade, since they allow basic access without using the internet.
The remainder of the Snow Leopard 10.6(.8) would be a download Software Update Combo v 10.6.8, either direct from Apple servers or through the computer's running Software Update. Once the computer is up to date in Snow Leopard, 10.6.8, then one could visit the Mac App Store, App Store, and iTunes Store; from the Mac App Store, and you could check/get the latest upgrade to Mac OS X, 10.9.2. An Apple ID is required to access.
The computer may not support Mavericks 10.9.2, or may be able to, but could use an upgrade of RAM capacity.
If your model and build year series info is correct:
Maximum Memory
8.0 GB (Actual) 4.0 GB (Apple)
Memory Slots
2 - 204-pin PC3-8500 (1066MHz) DDR3 SO-DIMM
For more information see the database download http://mactracker.ca
and also compare specs with macbook models at everymac.com.
The newer OS X systems that can use a Recovery HD partition on the hard disk drive, can start from there to repair their hard disk drive, and reformat the section where the Mac OS X runs, and reinstall that. Since there is no likelihood of that still being on the drive once it was FAT-32 reformatted, it will not be present to assist in attempts to reformat the drive; if the computer had been upgraded past Snow Leopard 10.6, to a later system that would have used the recovery partition, or the later internet recovery system. That goes to Apple Servers to use OS X Utilities and reinstall the system, helpful for computers without optical drives or system media. Your MacBook with 10.6.8 installed, then had to access the Mac App Store, to get 10.7.5, 10.8.5, or 10.9.x
Identify your Mac lookup by model number or serial number:
https://www.powerbookmedic.com/identify-mac-serial.php
Anyway, the hardware in the computer may need some inspection, troubleshooting, and maybe repair; but the original DVD install-restore disc has an Apple Hardware Test on it, for that series build model macbook. That could help in troubleshooting some aspects of the computer. Could be the hard disk drive failed; or if someone tried to upgrade the RAM, the system may not have worked correctly. Hard to say how it was messed up, at this stage. There are several possible causes.
Hopefully you can get the correct disc set from AppleCare.
You can call Support number, or use Contact Support page.
Good luck & happy computing! -
On start up of my new iMac it locks on the grey screen with the apple logo and the progress wheel spins. Boot up in safe and this is where it stopped at "BootCacheControl: Unable to open /var/db/bootcache.playlist: 2 no such file or directory. "
Reinstalling MacOS does NOT fix the problem for me. I'm still searching a solution !
Bernard -
Old address still showing in contact after I edit with new address. However, it shows correct address when in edit mode. Is this a new glitch on the iPhone iOS 7?
1) Is it a video clip? Something you recognize? To be clear, it's displaying at a point in your exported movie but doesn't appear at all in the sequence?
2) What are your sequence settings? Right-click your sequence and choose "Item Properties" to verify. -
Im using intel macbook pro 13" and since I'm using the new OSX Lion, the keyboard backlit won't turn off and it's eating up my precious battery. Im always mobile so this is very important. Apple doing something to fix this bug immediately?
multiplryan wrote:
To be totally honest, about 3 weeks prior I spilled some milk from cereal on the desk and a little bit got onto the battery.
I don't think you have a case.
You can replace the logic board yourself if you are a DIY'er and save some money. -
As the title says.
I was installing the new EFI software update on my macbook pro and I became stuck on the grey screen with the window that said "installing 2 items", its been on the same screen for 2 1/2 hours. does anyone know what I can do?
I don't want to restart it because im scared that something might go wrong.
operating lionLimitLess- wrote:
Hi,
I had the power supply connected when I attempted it previously but even so my problem occurred. My rom is different and so I still need to update it.
Thanks
I wanted to mark your answer helpful too but I didn't know that I could only put it for 2 answers. Sorry
That was good advice by G-N and s/he is correct about it. Unfortunately, ASC allows only 2 "helpful" and 1 "correct" marks per thread. -
Two Macbook pros circa 2009 in our temporary household in Turkey suddenly failed to boot and got stuck on the grey screen. They were able to boot at the Apple store, but not when we brought them back to our apartment. Could this be a coincidence? A
THank you Ogelthorpe. When my wife's computer I went on line to the site that you sent and tried everything But nothing worked. When my son came to visit and his MacBook Pro did exactly the same thing we became suspicious - too much of a coincidence. We took both computers somewhere else, out of our apartment, and they both booted. We ran disk utility on both, but the report in both cases was that there are no issues with the hard drive. Back in our apartment neither will boot up. My MacBook Pro is a later model with a solid state drive and it seems to work fine here.. I tried an external drive and it works fine. We think that this has something to do with some kind of magnetic interference in our apartment to which the 2009 drives are susceptible. It is indeed a mystery!
alf -
TS2570 Does this also include the scenario where the grey screen has a picture of 2 disk drives?
Does this also include the scenario where the grey screen has a picture of 2 disk drives?
One is labelled Macintosh HD and the other is Recovery HD.
The computer doesn't always start up like this but it has a few times now.This screen shows up if your holding the option/alt key down or perhaps if it's stuck or damaged.
It's called Startup Manager and shows your bootable options.
Another possible cause is your PRAM is not remmebering the System Preferences > Startup Disk selection.
Do a #2 Reset PRAM and head to System Preferences > Startup Disk and set it and hopefully that should resolve the issue.
..Step by Step to fix your Mac -
When I turn on my iMac, the grey screen comes on, the apple is there, the wheel turns and then it shust off. How can I fix this?
sabaideedog wrote:
Do you have an answer?
We are all volunteer end users like yourself, so please be patient. Please Google OS X Gray Screen on Startup and read the Apple Advice letter on it. Follow all the steps in the advice letter to the letter. -
My Mac mini turns on but doesn't move past the grey screen..... HELP??
Hi,
I have had my mac mini for 3 months and i went to turn it on today and it wont move past the grey screen with the apple logo and the swirling icon underneath. It had started to drop internet signal and also reacting slow and now this has happened. I have only had it three months from new and i dont know what to do. I have done a safe reboot etc and nothing has worked !! HELP!!Intermittent problems are by far the most difficult to identify and correct. You can run a test one time and it passes with flying colors and the next time it fails. Apple Hardware Test and Disk Utility are definitely the not the most rigerous tests available and are not nearly as thorough as the tests available to the Genius Desk personel.
-
Macbook not going past the grey screen
Im really bad with computers, but my problem is pretty much that every time i try to power up my macbook running leopard it stays on the grey screen with the apple logo and the wheel jsut keeps spinning, I've tried reseting the SMC and just using the reset bottons, but nothing is working, can anyone help?
You will have to reinstall OS X. See the following:
How to Perform an Archive and Install
An Archive and Install will NOT erase your hard drive, but you must have sufficient free space for a second OS X installation which could be from 3-9 GBs depending upon the version of OS X and selected installation options. The free space requirement is over and above normal free space requirements which should be at least 6-10 GBs. Read all the linked references carefully before proceeding.
1. Be sure to use Disk Utility first to repair the disk before performing the Archive and Install.
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger, Leopard or Snow Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Do not proceed with an Archive and Install if DU reports errors it cannot fix. In that case use Disk Warrior and/or TechTool Pro to repair the hard drive. If neither can repair the drive, then you will have to erase the drive and reinstall from scratch.
3. Continue with installation. When you reach the screen to select a destination drive click once on the destination drive then click on the Option button. Select the Archive and Install option. You have an option to preserve users and network preferences. Only select this option if you are sure you have no corrupted files in your user accounts. Otherwise leave this option unchecked. Click on the OK button and continue with the OS X Installation.
4. Upon completion of the Archive and Install you will have a Previous System Folder in the root directory. You should retain the PSF until you are sure you do not need to manually transfer any items from the PSF to your newly installed system.
5. After moving any items you want to keep from the PSF you should delete it. You can back it up if you prefer, but you must delete it from the hard drive.
6. You can now download a Combo Updater directly from Apple's download site to update your new system to the desired version as well as install any security or other updates. You can also do this using Software Update. -
My MBA now just goes to the apple logo on the grey screen but no further
My MBA now just goes to the apple logo on the grey screen but no further... I did some updates on Office but it did not freeze on install and recently I installed Joost.
I thought about booting it from a disc but now I have a disk stuck in my MAB superdrive that I can't get out since at this stage it will not eject... it is a mess...
I am new to Mac, so I am lost...
Anybody can help me with tips ?Installed Acrobat Reader for Mac. Rebooted and get apple logo, grey screen and perpetual blue screen, no further. I have dual systems installed and can boot Windows XP Pro with no problem so it appears to be a Mac OS problem, not hardware. Awaiting help.
_*WARNING to others who may have same problem installing Adobe Acrobat Reader and Office updates (see germmac post).*_ -
27' imac (2011) won't go past the grey screen
my 27" iMac (mid 2011) won't start up. When i turn it on, I get the grey screen with green vertical stripes. It will then go to the apple logo with task bar. It moves to about one third of the bar and then goes to a solid grey screen. It stays like this for under a minute and then shuts it self off and then restarts. It seems to be stuck in this loop. I have had it to the shop twice now- the first time they fixed something (can't remember) a hey have put in a new display/backlight this last time and it worked for about 30 minutes and then the problem started again.
Gave it a go, didnt work will just take it to the store !
-
Help!! - I am faced with the grey screen and spinning gear!!
Hi guys
I have an intel-based imac and when i performed routine updates on it, it took long to switch off so i manually turned it off with the button. Normally this gives no problem, but this time it refuses to go past the grey screen with the apple logo and spinning gear. I have tried many of the fixes but to no avail...does anyone have any step by step instructions/suggestions...I cant get to any of my uni work. I tried disk utility and it said my hard drive is fine, yet when i restart im back to the grey screen!
Please help, I cant access any of my files and cant risk having it wiped!!!
Thanks in advance - sorry if this might be in the wrong section!I had the same issue, and I had recently backed-up my files (mostly because the mac was acting wonky before this even happened), so I did an erase and install. Then I ran through all the software upgrades and installed all of them. When I did a required restart (for the Mac OS X 10.4.11 update) it went BACK to grey screen with spinning ball. Talk about frustrating!
I think there is something weird going on with the iTunes update and the Mac OS X 10.4.11 update. But one can't be used without the other. So I'm not sure how to update everything safely and get an up to date system, without having all the problems I had before. So now I'm using Mac OS X 10.4.7 so I can have a stable system to do my work, but I can't run iTunes 7.0. I'm too scared to update OS b/c I can't waste another day re-installing everything (for like the third time).
I'm a pretty new Mac user (year and half) so this may sound really dumb, but any suggestions would be very welcomed. I may start a new thread instead of hijacking this one... -
My late 2009 27" iMac gets stuck on the grey Apple logo when booting up. It boots correctly when in safe mode. I have tried erasing the HD and re-installing from a USB installer. It says the install is complete, but after restarting it gets stuck on the Apple logo again. This could possibly be an HD failure, but then why does Safe Mode still work and the USB install not work? Any ideas?
1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
Don't be put off merely by the seeming complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. All it does is to collect information about the state of the computer. That information goes nowhere unless you choose to share it. However, you should be cautious about running any kind of program (not just a shell script) at the behest of a stranger. If you have doubts, search this site for other discussions in which this procedure has been followed without any report of ill effects. If you can't satisfy yourself that the instructions are safe, don't follow them. Ask for other options.
Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
4. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
5. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
6. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Fonts 51 4 1000 25 5120 KiB/s 1024 85 \\b%% 20480 1 MB/s 25000 ports 'com.autodesk.AutoCad com.evenflow.dropbox com.google.GoogleDrive' DYLD_INSERT_LIBRARIES\ DYLD_LIBRARY_PATH -86 ` route -n get default|awk '/e:/{print $2}' ` 25 N\\/A down up 102400 25600 recvfrom sendto CFBundleIdentifier 25 25 25 1000 MB );N5=${#p[@]};p[N5]=` networksetup -listnetworkserviceorder|awk ' NR>1 { sub(/^\([0-9]+\) /,"");n=$0;getline;} $NF=="'${p[26]}')" { sub(/.$/,"",$NF);print n;exit;} ' `;f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' %s\ %s '%s\n\t(%s)\n' );S0() { echo ' { q=$NF+0;$NF="";u=$(NF-1);$(NF-1)="";gsub(/^ +| +$/,"");if(q>='${p[$1]}') printf("%s (UID %s) is using %s '${p[$2]}'",$0,u,q);} ';};s=(' /^ *$|CSConfigDot/d;s/^ */ /;s/[-0-9A-Fa-f]{22,}/UUID/g;s/(ochat)\.[^.]+(\..+)/\1\2/;/Shared/!s/\/Users\/[^/]+/~/g ' ' s/^ +//;5p;6p;8p;12p;' ' {sub(/^ +/,"")};NR==6;NR==13&&$2<'${p[10]} ' 1s/://;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: [^EO]|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[11]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' $0&&!/ / { n++;print;} END { if(n<200) print "com.apple.";} ' ' $3~/[0-9]:[0-9]{2}$/ { gsub(/:[0-9:a-f]{14}/,"");} { print|"tail -n'${p[12]}'";} ' ' NR==2&&$4<='${p[13]}' { print $4;} ' ' END { $2/=256;if($2>='${p[15]}') print int($2) } ' ' NR!=13{next};{sub(/[+-]$/,"",$NF)};'"`S0 21 22`" 'NR!=2{next}'"`S0 37 17`" ' NR!=5||$8!~/[RW]/{next};{ $(NF-1)=$1;$NF=int($NF/10000000);for(i=1;i<=3;i++){$i="";$(NF-1-i)="";};};'"`S0 19 20`" 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' 's/^.{52}(.+) <.+/\1/p' ' /Launch[AD].+\.plist$/ { n++;print;} END { if(n<200) print "/System/";} ' '/\.xpc\/(Contents\/)?Info\.plist$/p' ' NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$/ { print $3;} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:[^:]+//p ' '/root/p' ' !/\/Contents\/.+\/Contents|Applic|Autom|Frameworks/&&/Lib.+\/Info.plist$/ { n++;print;} END { if(n<1000) print "/System/";} ' '/^\/usr\/lib\/.+dylib$/p' ' /Temp|emac/d;/(etc|Preferences)\//s/^\.\/[^/]+//p;' ' /\/(Contents\/.+\/Contents|Frameworks)\/|\.wdgt\/.+\.([bw]|plu)/d;p;' 's/\/(Contents\/)?Info.plist$//;p' ' { gsub("^| ","||kMDItem'${p[35]}'=");sub("^.."," ") };1 ' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[9]}'{$2=$2-1;print}' ' BEGIN { i="'${p[26]}'";M1='${p[16]}';M2='${p[18]}';M3='${p[31]}';M4='${p[32]}';} !/^A/ { next;} /%/ { getline;if($5<M1) a="user "$2"%, system "$4"%";} /disk0/&&$4>M2 { b=$3" ops/s, "$4" blocks/s";} $2==i { if(c) { d=$3+$4+$5+$6;next;};if($4>M3||$6>M4) c=int($4/1024)" in, "int($6/1024)" out";} END { if(a) print "CPU: "a;if(b) print "I/O: "b;if(c) print "Net: "c" (KiB/s)";if(d) print "Net errors: "d" packets/s";} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/ )||(/v6:/&&$2!~/A/ ) ' ' $1~"lR"&&$2<='${p[25]}';$1~"li"&&$3!~"wpa2";' ' BEGIN { FS=":";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]" "$1;b=b$1;} END { if(b) print("\n\t* Code injection");} ' ' NR!=4{next} {$NF/=10240} '"`S0 27 14`" ' END { if($3~/[0-9]/)print$3;} ' ' BEGIN { L='${p[36]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n [N/A]";"file -b "F|getline T;if(T!~/^(AS.+ (En.+ )?text$|POSIX sh.+ text ex)/) F=F" ("T")";printf("\nContents of %s\n%s\n",F,f);if(l>L) printf("\n ...and %s more line(s)\n",l-L);} ' ' /^ +[NP].+ =/h;/^( +D.+[{]|[}])/{ g;s/.+= //p;};' ' /^ +B/{ s/.+= |(-[0-9]+)?\.s.+//g;p;} ' ' END{print NR} ' ' /id: N|te: Y/{i++} END{print i} ' ' / /{$0="'"${p[28]}"'"};1;' '/ en/!s/\.//p' ' NR!=13{next};{sub(/[+-M]$/,"",$NF)};'"`S0 39 40`" ' $10~/\(L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9;} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?Info\.plist$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' 's/0/Off/p' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps sudo\ crontab sudo\ iotop top pkgutil PlistBuddy whoami cksum kextstat launchctl sudo\ launchctl crontab 'sudo defaults read' stat lsbom mdfind ' for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done;' defaults\ read scutil sudo\ dtrace sudo\ profiles sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil sudo\ lsof test );c2=(com.apple.loginwindow\ LoginHook '-c Print /L*/P*/loginw*' '-c Print L*/P*/*loginit*' '-c Print L*/Saf*/*/E*.plist' '~ $TMPDIR.. \( -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 \)' '.??* -path .Trash -prune -o -type d -name *.app -print -prune' '-c Print\ :'${p[35]}' 2>&1' '-c Print\ :Label 2>&1|head -1' '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$Message' -k Sender kernel -k Message Req 'Beac|caug|dead[^bl]|FAIL|fail|GPU |hfs: Ru|inval|jnl:|last value [1-9]|n Cause: -|NVDA\(|pagin|proc: t|Roamed|rror|ssert|Thrott|tim(ed? ?|ing )o|WARN' -k Message Rne 'Goog|ksadm|SMC:' -o -k Sender fseventsd -k Message Req 'SL' " '-du -n DEV -n EDEV 1 10' 'acrx -o comm,ruid,%cpu' '-t1 10 1' '-f -pfc /var/db/r*/com.apple.*.{BS,Bas,Es,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cgh] ! -name *ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true \) -execdir stat -f:%Sc:%N -t%F {} \;|sort -t: -k2 |tail -n'${p[38]} '-L {/{S*/,},}L*/Lau* -type f' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' '-L /S*/L*/{C*/Sec*A,E}* {/,}L*/{A*d,Ca*/*/Ex,Compon,Ex,In,iTu,Keyb,Mail/B,P*P,Qu*T,Scripti,Sec,Servi,Spo,Widg}* -type f -name Info.plist' '/usr/lib -type f -name *.dylib' `awk "${s[31]}"<<<${p[23]}` "/e*/{auto,{cron,fs}tab,hosts,{[lp],sy}*.conf,pam.d,ssh{,d}_config,*.local} {,/usr/local}/etc/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t .launchd.conf" list getenv /Library/Preferences/com.apple.alf\ globalstate --proxy '-n get default' -I --dns -getdnsservers\ "${p[N5]}" -getinfo\ "${p[N5]}" -P -m\ / '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --only-files --files com.apple.pkg.*|sort|uniq' -kl -l -s\ / '-R -l1 -n1 -o mem -stats command,uid,mem' -i4TCP:0-1023 com.apple.dashboard\ layer-gadgets '-d /L*/Mana*/$USER&&echo On' '-app Safari WebKitDNSPrefetchingEnabled' );N1=${#c2[@]};for j in {0..8};do c2[N1+j]=SP${p[j]}DataType;done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n ' syscall::'${p[33+j]}':return { @out[execname,uid]=sum(arg0) } tick-10sec { trunc(@out,1);exit(0);} '";done;l=(Restricted\ files Hidden\ apps 'Elapsed time (s)' POST Battery Safari\ extensions Bad\ plists 'High file counts' User Heat System\ load boot\ args FileVault Diagnostic\ reports Log 'Free space (MiB)' 'Swap (MiB)' Activity 'CPU per process' Login\ hook 'I/O per process' Mach\ ports kexts Daemons Agents launchd Startup\ items Admin\ access Root\ access Bundles dylibs Apps Font\ issues Inserted\ dylibs Firewall Proxies DNS TCP/IP Wi-Fi Profiles Root\ crontab User\ crontab 'Global login items' 'User login items' Spotlight Memory Listeners Widgets Parental\ Controls Prefetching );N3=${#l[@]};for i in 0 1 2;do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Current ${p[29+j]}stream data";done;A0() { id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear >&-;date '+Start time: %T %D%n';};for i in 0 1;do eval ' A'$((1+i))'() { v=` eval "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};A'$((3+i))'() { v=` while read i;do [[ "$i" ]]&&eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}" `;[[ "$v" ]];};A'$((5+i))'() { v=` while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}" `;[[ "$v" ]];};';done;A7(){ v=$((`date +%s`-v[3]));};B2(){ v[$1]="$v";};for i in 0 1;do eval ' B'$i'() { v=;((v['$((i+1))']==0))||{ v=No;false;};};B'$((3+i))'() { v[$2]=`'${c1[30+i]}' "${s[$3]}"<<<"${v[$1]}"`;} ';done;B5(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`grep -Fv "${v[$1]}"<<<"$v"`;};C0(){ [[ "$v" ]]&&echo "$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { v=`sed -E "$s"<<<"$v"`&&C1 1 $1;};for i in 1 2;do for j in 2 3;do eval D$i$j'(){ A'$i' $1 $2 $3; C'$j' $4;};';done;done;{ A0;A2 0 $((N1+1)) 2;C0;A1 0 $N1 1;C0;B0;C2 27;B0&&! B1&&C2 28;D12 15 37 25 8;A1 0 $((N1+2)) 3;C0;D13 0 $((N1+3)) 4 3;D23 0 $((N1+4)) 5 4;for i in 0 1 2;do D13 0 $((N1+5+i)) 6 $((N3+i));done;D13 1 10 7 9;D13 1 11 8 10;D22 2 12 9 11;D12 3 13 10 12;D23 4 19 44 13;D23 5 14 12 14;D22 6 36 13 15;D22 7 37 14 16;D23 8 15 38 17;D22 9 16 16 18;B1&&{ D22 11 17 17 20;for i in 0 1;do D22 28 $((N2+i)) 45 $((N4+i));done;};D22 12 44 54 45;D22 12 39 15 21;A1 13 40 18;B2 4;B3 4 0 19;A3 14 6 32 0;B4 0 5 11;A1 17 41 20;B7 5;C3 22;B4 4 6 21;A3 14 7 32 6;B4 0 7 11;B3 4 0 22;A3 14 6 32 0;B4 0 8 11;B5 7 8;B1&&{ A2 19 26 23;B7 7;C3 23;};A2 18 26 23;B7 7;C3 24;A2 4 20 21;B7 6;B2 9;A4 14 7 52 9;B2 10;B6 9 10 4;C3 25;D13 4 21 24 26;B4 4 12 26;B3 4 13 27;A1 4 22 29;B7 12;B2 14;A4 14 6 52 14;B2 15;B6 14 15 4;B3 0 0 30;C3 29;A1 4 23 27;B7 13;C3 30;D13 24 24 32 31;D13 25 37 32 33;A1 23 18 28;B2 16;A2 16 25 33;B7 16;B3 0 0 34;B2 21;A6 47 21&&C0;B1&&{ D13 21 0 32 19;D13 10 42 32 40;D22 29 35 46 39;};D23 14 1 48 42;D12 34 43 53 44;D22 0 $((N1+8)) 51 32;D13 4 8 41 6;D12 26 28 35 34;D13 27 29 36 35;A2 27 32 39&&{ B2 19;A2 33 33 40;B2 20;B6 19 20 3;};C2 36;D23 33 34 42 37;B1&&D23 35 45 55 46;D23 32 31 43 38;D12 36 47 32 48;D13 20 42 32 41;D13 14 2 48 43;D13 4 5 32 1;D22 4 4 50 0;D13 14 3 49 5;D12 26 48 59 49;B3 4 22 57;A1 26 46 56;B7 22;B3 0 0 58;C3 47;D23 22 9 37 7;A7;C2 2;} 2>/dev/null|pbcopy;exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
7. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
8. If you see an error message in the Terminal window such as "syntax error," enter
exec bash
and press return. Then paste the script again.
9. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
10. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
[Process completed]
to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report the results. No harm will be done.
11. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with "Model Identifier." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
12. When you post the results, you might see the message, "You have included content in your post that is not permitted." It means that the forum software has misidentified something in the post as a violation of the rules. If that happens, please post the test results on Pastebin, then post a link here to the page you created.
Note: This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.
Maybe you are looking for
-
Fault found with opening balances output on Trial Balance report
When running the Trial Balance report and adding "Opening Balances" and taking the "OB from Start of Fiscal Year" option, the relevant opening balances are not shown from the closing balance of the prior period. All balance sheet accounts should alwa
-
My phone number is unavailable in imessage
After returning from holiday, my imessage no longer works unless it is through email, which I dont like. I have tried loads of options and nothing has worked.
-
OC4J_BI_Forms Fails To Start After Windows Reboot
Hi, After upgrading the metadata repository database to 9.2.0.6 and updating the compatible parameter and creating a new pfile, my OC4J_BI_Forms server fails to start automatically after a reboot. I can start the OC4J_BI_Forms server manually and it
-
How can i use ni 5122 in matlab ?
Hi all, i want to use my 5122 card in matlab. is that possible ? Maik
-
Patters for avoiding the '/' (in java.util.regex)
Hi all , i wanted to knw the pattern format (in java.util.regex) for avoiding the '/' at the begenning of a line ....... hope to get the best answers .... thnx 'n cheers max