Is this respectable or not

2.8 ghz P4 retail box
875p MB
1gig Geil ultra ddr400 ram (set at 2.55v)
120gig Seagate SATA HD
ver 1.8 bios (set at turbo mode)
ATI radeon 9800 pro (AA set to 2x standard voltage and gpu settings)
Just ran 3D Mark Pro in 800x600 and scored 5514 3d marks
I dont know if this is a good score or not...anyone have any input?
I tried to use ultra turbo mode but system wont boot with it...any suggestions on how I can get it to run in Ultra?
System temp maxed at 41.7C during the test and runs at 33.1c idle...is that an ok range for that load and for idle.
Thanks
einsteins

Einsteins-First off run the benchmark as noted at 1024 x 768 (32bit high color) resolution. Go to your ATI control panel and set the sliders for both Direct 3D and Open GL to performance mode. Shut down AA and AF. Vertical sync off. Now you are properly running the test in its standard configuarion.
Next-3Dmark 2003 (unlike 3D mark 2001)is very-very video card dependant. Bios tweaks are always helpful-but you will not see a significant increase with them. Overclocking your card to its limit(no tearing,artifacting,slowdowns,crashing to desktop etc)will have a significant effect. (My Radeon 9800pro is clocked at 421/371-I also have a special fan under the card exhausting heat out the rear of the machine)As far as most effective system tweaks-overclocking the system will give the greatest yields. My system scores just over 5800 at stock and just over 6400 overclock. I'm sure there is more overclocking headroom for my card. I am using only cas3 ram currently and an older(Stable)bios without the special modes(fast-turbo-ultra). Good luck!!!!
Intel P4 3.00ghz(non overclocked-HT enabled)
1024 Crucial DDR3200(upgrade to Mushkin Level II $ permitting)
ATI Radeon 9800 pro
120 gig Western Digital Spec Ed.
Toshiba 16x48 DVD-Rom
Plextor 48x24x48 CD RW
Creative Audigy2 6.1 Platinum
Cooler Master201c
Windows XP home
875P neo

Similar Messages

Exception in Payment Proposal - Pmnt methods for this run are not specified

Dear all,
I want to ask if it is possible to run a payment proposal for AP transactions together with AR. The AR line items are used for clearing. Actually, this is the first time we execute proposal run which contains AP and AR respectively. And during the proposal, AR line item is an exception - 'Pmnt methods for this run are not specified in the master record or in item'. We already checked the master record, and there is a payment method. However, it was not captured during the payment proposal. Does it have something to do with the Document Type?
Thank you once again for all your usual support.
Regards,
April

To: Karthik, pushkaraj, JeCcas_DJ
Thank you very much for your responses.
I've checked already FBZP and Customer Master Record, payment methods were defined. Also, during the payment run, all line items have the same payment method, but only the AR transaction was not accepted.
I think the problem is the same as what pushkaraj mentioned. We have payment method 'D' defined only for outgoing payments and not for incoming payments. I guess that is the problem.
By the way, can I create another entry 'D' for payment method-incoming payments? Would there be conflict if I assigned same ID?
Regards and thank you once again...
April

Getting this error while opening a folder : This file does not have a program associated with it for performing this action. Please install a program or, if one is already installed, create an association in the Default Programs control panel

Hi,
While trying to open a folder on my Windows 7 Home Premium, an error comes "This file does not have a program associated with it for performing this
action. Please install a program or, if one is already installed, create an association in the Default Programs control panel." I tried searching on the net but did not get great support for the issue when it happens with folder opening.

Hi Nikunj Shah,
First, I suggest you download
Microsoft Safety Scanner or
Malicious Software Removal Tool to run a full scan.
The error messages here seems to be caused by the corrupted registries, which related with the folder association.
You may take a try to merge the following registry settings to reset the folder association, before that, remember to backup your registry settings first:
How to back up and restore the registry in Windows
Copy and paste the following commands into Notepad, and save it to a .reg file:
=================
Windows Registry Editor Version 5.00
[HKEY_CLASSES_ROOT\Folder]
"ContentViewModeLayoutPatternForBrowse"="delta"
"ContentViewModeForBrowse"="prop:~System.ItemNameDisplay;~System.LayoutPattern.PlaceHolder;~System.LayoutPattern.PlaceHolder;~System.LayoutPattern.PlaceHolder;System.DateModified"
"ContentViewModeLayoutPatternForSearch"="alpha"
"ContentViewModeForSearch"="prop:~System.ItemNameDisplay;System.DateModified;~System.ItemFolderPathDisplay"
@="Folder"
"EditFlags"=hex:d2,03,00,00
"FullDetails"="prop:System.PropGroup.Description;System.ItemNameDisplay;System.ItemTypeText;System.Size"
"NoRecentDocs"=""
"ThumbnailCutoff"=dword:00000000
"TileInfo"="prop:System.Title;System.ItemTypeText"
[HKEY_CLASSES_ROOT\Folder\DefaultIcon]
@=hex(2):25,00,53,00,79,00,73,00,74,00,65,00,6d,00,52,00,6f,00,6f,00,74,00,25,\
00,5c,00,53,00,79,00,73,00,74,00,65,00,6d,00,33,00,32,00,5c,00,73,00,68,00,\
65,00,6c,00,6c,00,33,00,32,00,2e,00,64,00,6c,00,6c,00,2c,00,33,00,00,00
[HKEY_CLASSES_ROOT\Folder\shell\explore]
"MultiSelectModel"="Document"
"ProgrammaticAccessOnly"=""
"LaunchExplorerFlags"=dword:00000018
[HKEY_CLASSES_ROOT\Folder\shell\explore\command]
"DelegateExecute"="{11dbb47c-a525-400b-9e80-a54615a090c0}"
[HKEY_CLASSES_ROOT\Folder\shell\open]
"MultiSelectModel"="Document"
[HKEY_CLASSES_ROOT\Folder\shell\open\command]
"DelegateExecute"="{11dbb47c-a525-400b-9e80-a54615a090c0}"
@=hex(2):25,00,53,00,79,00,73,00,74,00,65,00,6d,00,52,00,6f,00,6f,00,74,00,25,\
00,5c,00,45,00,78,00,70,00,6c,00,6f,00,72,00,65,00,72,00,2e,00,65,00,78,00,\
65,00,00,00
[HKEY_CLASSES_ROOT\Folder\shell\opennewprocess]
"MUIVerb"="@shell32.dll,-8518"
"MultiSelectModel"="Document"
"Extended"=""
"LaunchExplorerFlags"=dword:00000003
"ExplorerHost"="{ceff45ee-c862-41de-aee2-a022c81eda92}"
[HKEY_CLASSES_ROOT\Folder\shell\opennewprocess\command]
"DelegateExecute"="{11dbb47c-a525-400b-9e80-a54615a090c0}"
[HKEY_CLASSES_ROOT\Folder\shell\opennewwindow]
"MUIVerb"="@shell32.dll,-8517"
"MultiSelectModel"="Document"
"OnlyInBrowserWindow"=""
"LaunchExplorerFlags"=dword:00000001
[HKEY_CLASSES_ROOT\Folder\shell\opennewwindow\command]
"DelegateExecute"="{11dbb47c-a525-400b-9e80-a54615a090c0}"
[HKEY_CLASSES_ROOT\Folder\ShellEx\ContextMenuHandlers\BriefcaseMenu]
@="{85BBD920-42A0-1069-A2E4-08002B30309D}"
[HKEY_CLASSES_ROOT\Folder\ShellEx\ContextMenuHandlers\Library Location]
@="{3dad6c5d-2167-4cae-9914-f99e41c12cfa}"
[HKEY_CLASSES_ROOT\Folder\ShellEx\ContextMenuHandlers\Offline Files]
@="{474C98EE-CF3D-41f5-80E3-4AAB0AB04301}"
[HKEY_CLASSES_ROOT\Folder\ShellEx\DragDropHandlers\{BD472F60-27FA-11cf-B8B4-444553540000}]
@=""
[HKEY_CLASSES_ROOT\Folder\ShellEx\PropertySheetHandlers\BriefcasePage]
@="{85BBD920-42A0-1069-A2E4-08002B30309D}"
[HKEY_CLASSES_ROOT\Folder\ShellEx\PropertySheetHandlers\Offline Files]
@="{7EFA68C6-086B-43e1-A2D2-55A113531240}"
[-HKEY_CLASSES_ROOT\Folder\ShellNew]
[HKEY_CLASSES_ROOT\Folder\ShellNew]
"Directory"=""
"IconPath"=hex(2):25,00,53,00,79,00,73,00,74,00,65,00,6d,00,52,00,6f,00,6f,00,\
74,00,25,00,5c,00,73,00,79,00,73,00,74,00,65,00,6d,00,33,00,32,00,5c,00,73,\
00,68,00,65,00,6c,00,6c,00,33,00,32,00,2e,00,64,00,6c,00,6c,00,2c,00,33,00,\
00,00
"ItemName"="@shell32.dll,-30396"
"MenuText"="@shell32.dll,-30317"
"NonLFNFileSpec"="@shell32.dll,-30319"
[HKEY_CLASSES_ROOT\Folder\ShellNew\Config]
"AllDrives"=""
"IsFolder"=""
"NoExtension"=""
==================
Once done, right-click the REG file and choose Merge. Alternately, you can open the Registry Editor and then using the
Import option from the File menu, to merge the REG file contents.
Let me know if you need any further help.
Best regards
Michael Shao
TechNet Community Support

Error 8062 when I try to copy or move files on my macbook: "This operation could not be completed because an unexpected error occurred (error code -8062)". Can even not install new software now!!

Since a few days when I try to copy or move files on my macbook, I often get an error message saying "This operation could not be completed because an unexpected error occured (error code -8062)". And then it just quits the copy or move.
I searched a lot on the internet, but only found solutions for cases you cannot empty the trash due to this issue.
I tried those solutions for my trash and that helped after some trying.
However, I still have the problem with copying and moving files.
I even cannot install new software now, as it has to copy itself to the programs-directory, and gives the same error-message.
Who can help me??
Cannot seem to find any info on it on the support-forums or elsewhere.
My user-account is administrator, I use a 13" Macbook Aluminium (Late 2008). Mac OS X 10.6.8 CPU 2Ghz Intel Core Duo, RAM: 4GB 1067 MHz DDR3.
Any help would be greatly appreciated...
Otto

Tips I received so far (thanks to A-Mac via Twitter http://www.a-mac.nl and Remco Kalf http://www.remcokalf.nl/)
- make sure you have at least 10% of your harddisk in free space (I had only 5%).
- do a PRAM-reset (http://support.apple.com/kb/ht1379)
- perform a hardware test (http://support.apple.com/kb/HT1509)
- make a complete backup (with for example Carbone Clone Copier, see http://www.bombich.com/)
- after complete backup: use diskwarrior (boot from Diskwarrior DVD, first perform diagnostics, then perform "Rebuild" which rebuilds your file directory).
So far I only cleared up some space on my HD, and already the problem occurs less.
Still, I will go through the other tips too.
(will post progress)

I have recently upgraded to 7.0.2 and can no longer charge my iphone 4 as i recieve the message this accessory may not be supported, any advice would be appreciated

i have recently upgraded to 7.0.2 and can no longer charge my iphone 4 as i recieve the message this accessory may not be supported, any advice would be appreciated
i have also tried 4 different chargers both official apple and non official

i have tried this but still not working i found a way of fixing it by restoring the phone but this has now put my phone in recovery mode and when i try to fix it i get an error 14 which i have no clue what it means

JCOerror: This system does not let you log on using a password

Hi,
"JCOerror: This system does not let you log on using a password"
This is the error message I get from MII tries to connect to the Production ECC using my credentials to perform a BAPI call.
These credentials work fine interactively (using the SAP GUI) and for BAPI calls from MII on SAP Development instances.
I can interpret this message in two ways:
- My login can not log on using password (though I can interactively)
- The server does not allow logging on using password only. (It might require to pre-authorize the connecting server as well).
I guess my question can be if this error requires adding additional rights to my login for the production environment, or if this is a global SAP setup for this system? Or something else?
In either way, what is required to have this work?
Thanks.

Hi,
Kindly try the following options.
Try executing the BAPI seperately in se37, using your login credentials.
Check whether RFC is enabled for the BAPI.
Check whether the SAP server is details are furnished correctly in "SAP Server"(available under "Data Services") editor.
We can ensure this by checking the connection status link in xMII.(Link is available under "Data Services").
If connection status is "Running" then SAP server setting configuration is fine. Else it is not configured properly.
Try executing the BAPI in BLS(Business Logic Services) using JCO connector.
I believe if any one of these scenarios fail then "Proxy Error" might thrown.
Thanks
Rajesh Sivaprakasam

This system does not let you log on using a password

hi all, i am very new to sap basis. i have changed the below profile parameters in RZ10.
login/min_password_length=3
login/min_password_lowercase=1
login/min_password_uppercase=1
login/min_password_digits=2
login/min_password_specials=1
after changing values i restarted the Instance. But the problem is when i am trying to login to the system it is showing an error message : "This system does not let you log on using a password". I know why this error occurs...
but how to resolve this error? plz Help.
Thanks in advance

login/min_password_length=3
login/min_password_lowercase=1
login/min_password_uppercase=1
login/min_password_digits=2
login/min_password_specials=1
The correct parameter for Min password Lenght is login/min_password_lng.
You can change this at OS level restart and see how it goes...
Regards
Juan

HT4108 Digital AV adapter does not support iPad 2. Error message "This accessory does not supported by iPad"

Just bought latest digital AV adapter MD098ZM/A. Does not work with my iPad 2. Error messade" this accessory is not supported by iPad" while the package saying it supports iPad 2 and later.

It's works with the new iPad. It said "accessory not supported". I clicked OK and now it works.

I am trying to download pictures from my canon rebel eos to my Ipad but i get the message "this device is not supported" what can I do ?

I just bought an Apple Lighting to USB Camera Adapter. When I got home to and connected it to my Canon Rebel EOS Digital Camera. I received the error message "This device is not supported" I was wondering if there is any software or drivers I need to download?
Thanks
Don

I use Canon Cameras and have no problems downloading photos from the camera to the Lightning to USB Camera Adapter. My questions and suggestions might be basic but just to make sure:
1. This is an iPad forum area. Are you using the lightning to USB camera adapter with an iPad? Your info in your original post says iPod. I'm not sure that the adapter works with an iPod.
2. After you connect the adapter to your iPad and then use a USB cable to connect the adapter to the camera did you turn on the camera?
3. If you did turn on the camera and still did not get the import of photos to start try a reset your iPad. Press and hold the Home and Sleep buttons simultaneously until the Apple logo appears. Let go of the buttons and let the device restart. This will not cause any data loss.

I want update firmware 2.9 but apear this message "This software is not supported on your system."

hi
I want update firmware .details my system is
Hardware Overview:
Model Name:          MacBook Pro
Model Identifier:          MacBookPro9,2
Processor Name:          Intel Core i5
Processor Speed:          2.5 GHz
Number of Processors:          1
Total Number of Cores:          2
L2 Cache (per Core):          256 KB
L3 Cache:          3 MB
Memory:          4 GB
Boot ROM Version:          MBP91.00D3.B08
SMC Version (system):          2.2f38
Serial Number (system):          C1MHQC17DTY3
Hardware UUID:          EF0C6F81-20AD-50FA-9DD5-C8E084DF8E8C
Sudden Motion Sensor:
State:          Enabled
but when install the last update MacBookProEFIUpdate2.9 i got error like this
"This software is not supported on your system."
please help me thanks

OK, so the firmware is the same as mine, and yet Apple Support offered this EFI and SMC update packages, which should give a message that our computers are updated.
However, the update packages fail to run.
Did Apple neglect to give the correct update for the mid-2012 issue of MacBook Pro 13-inch? I have the i7 Intel processor, instead of the i5, and I was sold this unit as having two processors, but the System info only lists a single processor.
Is one of the problems with Intel-based MacBook Pro units that the integration wasn't without bugs that cause processor hang when running the OS Lion, even with updates to 10.7.5?
Shouldn't the EFI and SMC updaters run on these machines as stated in the Apple Support article?
What will Apple do for these customers?

I have just purchased a lightning to 30 pin adaptor to use on an iPad mini and a gen5 iPod touch both devices are running iOS 8.1.3 and come up with The error message "this accessory is not supported by this device "

I have just purchased a lightning to 30 pin adaptor to use on an iPad mini and a gen5 iPod touch both devices are running iOS 8.1.3 and come up with The error message "this accessory is not supported by this device "
THis is means they are not charging on a 30 pin cable and the touch won't work in my Apple iPod dock - no audio out or charge. Have re powered both devices to no avail am wondering if the iOS version is the problem
Help!

If it is a lightning to 30 pin adaptor, and you have a 7th Generation Nano it has to fit the Nano.
This is lightning to 30 pin adapter: http://www.bestbuy.com/site/Apple%26%23174%3B---Lightning-to-30-Pin-Adapter/6651 936.p?id=1218803450821&skuId=6651936#tab=overview
Is this what you bought?
You need to contact Sony and see if they model you have is compatible with the docking adapter. It may not be.

I am trying to install Elements, I get this constant error message. This installation is not supported by this processor type. Contact your product vendor.

I am trying to install Elements, I get this constant error message. This installation is not supported by this processor type. Contact your product vendor.
I am using Windows 8.

Hi,
Which version of Photoshop Elements are you trying to install?
Are you installing from DVD or a download?
If DVD, make sure you are using the Windows one, not the MAC one.
What device are you trying to install on?
Does your system meet the required spec?
Are you on Windows 8 or Windows 8.1?
Brian

HT1237 My MacBookPro9,2 gets error message: "This software is not supported on your system." Audio jack is ignored. What else can I do?

MACBOOK Pro 13-inch Mid 2012
2.9GHz Intel Core i7
8GB 1600 MHz DDR3
Intel HD Graphics 40000 512 MB
Mac OS X Lion 10..5 (11G63)
Model Identifier:                    MacBookPro9,2
Boot ROM Version:          MBP91.00D3.B08
SMC Version (system):          2.2f44
Passed Last Power on Self-Test
The MacBook EFI Updater File that I downloaded from the Apple website for Support:
http://support.apple.com/kb/HT1237
--> shows my Model McBookPro 9,2 as needing
EFI Boot ROM version MBP91.00D3.B08 (EFI 2.9) (http://support.apple.com/kb/DL1593)
SMC version 2.2f44 (SMC 1.8) (http://support.apple.com/kb/DL1633)
I downloaded and tried to run both the files
MacBookProEFIUpdate2.9.dmg 9/19/12
AND
MacBookProSMCUpdate.pkg
as offered on this matrix, which instructs:
"This article lists firmware updates that were released for Intel-based Macs. They update the firmware that originally shipped from the factory. If your computer does not appear on this list, an update from the factory firmware is not necessary.
If you are unsure whether your computer needs a particular update, simply download and open the update installer. The installer will alert you if the firmware update is already installed or not needed."
and instead of a message telling me of the proper update
"This software is not supported on your system."
So, why would the manual updater not tell me I already have the proper SMC and EFI updates?
What is the reason I get the message that the software I downloaded from Apple Support is not supported on my system?
Is this indicative of a larger problem with my MACBOOK PRO?

[email protected],
why were you trying to reïnstall the Boot ROM and SMC versions that were already installed on your MacBook Pro?
I agree that a “not supported” message is certainly less clear than an “already installed” message would have been.

Error message: this computer is not supported by the system recovery media.

I replaced a bad samasung hard drive in my Pavilion dv6z 3200 with a Seagate Momentus XT 750 GB 7200RPM SATA 6Gb/s 32 MB Cache 2.5 Inch Solid State Hybrid Drive ST750LX003 and when trying to restore Windows 7 64 bit OS get the error message "this computer is not supported by the system recovery media"

Is the new hdd at least as large a capacity as the original? Can be larger capacity, but sometimes smaller will cause error.
Enter BIOS by tapping F10 key. Is all system info intact/complete?
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others**

My iPhone 4 no longer connects to my car or alarm clock after a recent sync to my computer. The message at I get when trying to. Connect is "this accessory is not optimized for the device" or something like that. Anyone know how to fix this?

My iPhone 4 no longer connects to my car or alarm clock after a recent sync to my computer. The message at I get when trying to. Connect is "this accessory is not optimized for the device" or something like that. Anyone know how to fix this?

Hello there philp_69,
If I understand correctly it sounds like your phone hasnt been recognized in iTunes on your PC since the last couple of updates. I would use the troubleshooting in the following article which will walk you through the steps one by one.
iPhone, iPad, or iPod touch not recognized in iTunes for Windows
Thank you for using Apple Support Communities.
All the very best,
Sterling

Is this respectable or not

Similar Messages

Maybe you are looking for