Is "Two independent 10/100/1000BASE-T Ethernet (RJ-45) interfaces" a switch?

Can I use the second ethernet port in the back of my Mac Pro to connect an older mac to my network?

Its better than that. You can enable a simple Router in the Sharing Mac, with Router Address 192.168.2.1. It can pass out "private" Addresses to attached devices using DHCP, and can autospeed to 10, 100 or 1000 base-T, depending on attached devices. (1000 speeds require a cable with all 8 conductors present). The Mac Pro will adapt to either a straight or cross cable.
System Preferences > Sharing > Internet Sharing

Similar Messages

Does SFP-TX support Tri-Rate(10/100/1000Base-TX) on Aruba 72xx controllers?

Q: Does SFP-TX support Tri-Rate(10/100/1000Base-TX) on Aruba 72xx controllers?
A: Aruba do not support 10/100 on copper SFP on any controller platform.
The SFP-TX support only 1000Base-TX when used on the 72xx controllers.
If the peer interface is 100Base-TX then we will have a speed mismatch and the link will be down.

yes. but it still says linked not connected
# sh interface ethernet 1/19
Ethernet1/19 is down (Link not connected)
Hardware: 1000/10000 Ethernet, address: 547f.eebb.2580 (bia 547f.eebb.2580)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is access
auto-duplex, 1000 Mb/s, media type is 10G
Beacon is turned off
Input flow-control is off, output flow-control is off
Rate mode is dedicated
Switchport monitor is off
  EtherType is 0x8100
  Last link flapped never
Last clearing of "show interface" counters 00:00:07
30 seconds input rate 0 bits/sec, 0 packets/sec
30 seconds output rate 0 bits/sec, 0 packets/sec
Load-Interval #2: 5 minute (300 seconds)
    input rate 0 bps, 0 pps; output rate 0 bps, 0 pps
RX
    0 unicast packets 172 multicast packets 22 broadcast packets
    194 input packets 23236 bytes
    0 jumbo packets 0 storm suppression bytes
    0 runts 0 giants 0 CRC 0 no buffer
    0 input error 0 short frame 0 overrun   0 underrun 0 ignored
    0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop
    0 input with dribble 0 input discard
    0 Rx pause
TX
    0 unicast packets 0 multicast packets 0 broadcast packets
    0 output packets 0 bytes
    0 jumbo packets
    0 output errors 0 collision 0 deferred 0 late collision
    0 lost carrier 0 no carrier 0 babble 0 output discard
    0 Tx pause
0 interface resets
# sh interface ethernet 1/19 status
Port          Name               Status    Vlan      Duplex Speed   Type
Eth1/25       --                 notconnec 160       full    1000    SFP-1000BAS

10/100 Base T ethernet

So I'm going to college this year and my dorm requires my computer to have a 10/100 Base T ethernet card. All I know is that it is some little green square in the computer that you plug a chord into. Does the Macbook have one of them?

This is what it includes, bothe ethernet and wirelss networking so you can use it at wifi spots. But it's not green it's black and right next to the magsafe connector.
Networking: Built-in 10/100/1000BASE-T (Gigabit) Ethernet
Wireless: Built-in AirPort Extreme Wi-Fi (based on IEEE 802.11n draft specification)2; built-in Bluetooth 2.0+EDR (Enhanced Data Rate) module

HT1660 i have two independent itunes libraries on my computer right now. how do i consolidate them into one library? how do i get rid of duplicate files?

i have two independent itunes libraries on my computer right now. how do i consolidate them into one library? how do i get rid of duplicate files?

Hello rmunsey,
Thank you for the question. It sounds like you have two separate iTunes Libraries but would like to add the music from one to the other to have one consolidated library.
If you know where the files are for each library, I recommend opening one iTunes Library in iTunes and importing the files from the other library using the following steps:
Open iTunes
From the File menu, choose one of the following choices:
MacAdd to Library
Windows
Add File to Library
Add Folder to Library
Navigate to and select the file or folder that you want to add
Adding music and other content to iTunes
http://support.apple.com/kb/ht1473
Next, you can search for duplicates:
Choose View > Show Duplicate Items to show duplicate items (matches are based on the song name and artist). If you have multiple versions of the same song (for example, live and studio versions, or versions from different albums) you can hold the Alt or Option key (for Mac OS X) or the Shift key (for Windows) and choose View > Show Exact Duplicate Items. This will show only duplicate songs having the same name, artist, and album.
How to find and remove duplicate items in your iTunes library
http://support.apple.com/kb/ht2905
This should help you identify the duplicates all at one time so that you can delete the extra versions of songs.
Thank you for using Apple Support Communities.
Best,
Sheila M.

How can two independent DirectAccess servers be set up safely in the same domain?

I've got a single-tier certificate authority running on a 2008 r2 domain controller with an expiring root certificate. I have a new 2012 r2 domain controller with a new single-tier certificate authority. I also have a DirectAccess server running on 2012
server (two NICs, NAT, IP-HTTPS only). I'd like to get a new DirectAccess server set up running server 2012 r2 using the new CA for the various DirectAccess server and client computer certs. I can get the new environment working and flip machines from
the existing implementation to the new implementation.
I was previously told by a tech working one of my Microsoft support tickets that two independent DirectAccess servers can't run in the same domain. However, I posted a related question
https://social.technet.microsoft.com/Forums/projectserver/en-US/ab53a314-91ea-4d40-afd5-6b8f62698547/2012-directaccess-and-expiring-certificate-authority?forum=winserverNIS and got a response indicating that two independent DirectAccess servers can run
in the same domain. If I can carefully get a second server operational within the same domain, I can build a reg file to deploy to all machines prior to the cutover that will simulate the gpupdate for broken machines in the field, getting them connected so
the policy can be properly pulled from a DC. Would anyone else be willing to confirm or elaborate on operating two independent DirectAccess servers in the same domain? What are the gotchas?

Hi,
Yes you can have 2 Da deployments in one domain.
I have done this a number of times for customer when upgrading from UAG DA to 2012.
Make sure you use different Group policies for the DA servers and Clients. make sure you target the client with only one GPO at a time. Also use different AD groups.
You then change the GPO assignment to the clients and they will flip when the client does a gp update. I have done this for a site that had over 5000 clients and we didn't have one call about it.
You can use DirectAccess Offline Domain Join for any broken machines.
https://technet.microsoft.com/en-gb/library/jj574150.aspx
Regards, Rmknight

Driver for my Integrated 10/100 BASE-T Ethernet LAN

need drivers for integrated 10/100base-t ethernet lan driver win8 x 64bit i have the
HP 15-d103tx Notebook PC
here http://h10025.www1.hp.com/ewfrf/wc/document?docname=c04206739&tmp_task=prodinfoCategory&cc=us&dlc=en...
please help

The Integrated 10/100 BASE-T Ethernet LAN is not the wireless network adapter.
That is the wireless network adapter and has nothing to do with the wireless.
If you need a driver for the wireless network adapter, then please do this...
Go to the device manager and click on the Network Controller needing drivers.
Then click on the Details tab at the top of the network controller window.
Now you see a Property drop down list and it is defaulted to Device Description.
Drop down on that and select the second item on the list (Hardware ID's).
Post the top string of characters that begin with PCI\VEN.

How do I create an xy chart using two independent while loops?

Hi everyone,
I am trying to develop a data acquisition program. In this program, I have two independent while loops that each output a number of type double each iteration of the loop. I am able to successfully create two independent waveform charts (data vs. time) for each of the loops when it is placed inside. However, I now want to create an xy chart of the live data (the output of one loop is x and the output of the other is y).
I am having trouble doing this because of the separate nature of the loops...when I try to pull data outside of the loops it (naturally) doesn't refresh with each loop iteration causing the xy chart to not work in the way I intend. Is there an easy way to fix this? If more clarification is needed, please let me know!
David
Solved!
Go to Solution.

Yes, more clarification is needed. Please attach your code to clarify.
I'll take a wag at it, though. It sounds like you are trying to pair X and Y data which happen during a single time chunk, then repeat, is this right? (If not, don't bother to read on.) If so, why not just use a single loop. If your VI is getting too big/complicated for comfort, just put the data-generating stuff into subVIs which run to generate a single data point, then stop, put them into a while loop and send the putputs to a graph or chart inside the loop. That way you won't extend your data trace until you get one and only one point from each subVI and things will stay synchronized.
Cameron
To err is human, but to really foul it up requires a computer.
The optimist believes we are in the best of all possible worlds - the pessimist fears this is true.
Profanity is the one language all programmers know best.
An expert is someone who has made all the possible mistakes.
To learn something about LabVIEW at no extra cost, work the online LabVIEW tutorial(s):
LabVIEW Unit 1 - Getting Started
Learn to Use LabVIEW with MyDAQ

Two independent installation and performance issue

Hi,
We have installed two independent DBs (11gr2 enterprise 64 bit)on a large box with 80 cores 256GB RAM.
The data files for both DBs are on ram. The objective is to find if we can double perf number with two instances.
What we see is that when both instances are run the "log file sync" event takes 5 times more time (there are other wait events also go up).
db2: (when db2 running alone)
log file sync 202,445 21 0 .9 Commit
db2: (when db1 & db2 running together)
log file sync 267,512 97 0 4.5 Commit
The CPU load average -1 comes down from
14.1 to 1.68 though CPU utilization jumps from 41% to 82%.
There are two independent installations. We are trying to find out how one instance of DB can affect other (make other wait more), unless there is an underlying issue in the common resource used by both.
The SGAs should be allocated and accessed by DBs separately, right?
ipcs -m shows:
------ Shared Memory Segments --------
key shmid owner perms bytes nattch status
0xe93e5adc 262144 oracle 660 4096 0
0x13074fa0 491521 oracle 660 1612709888 0
0xcd05b8c4 622594 oracle 660 4096 0
if we turn off one db then
------ Shared Memory Segments --------
key shmid owner perms bytes nattch status
0x13074fa0 491521 oracle 660 1612709888 0
0xcd05b8c4 622594 oracle 660 4096 0
I am not very familiar oracle and do not know how to find memory layout of oracle DB. Any help/pointer is appreciated.
What is the best way to find out that two DBs do not share the same SGA/resources?
The two DBS have everything different except ora inventory.
Kallol Biswas
[email protected]
NucleoDyne Systems, Inc.

Without a lot more information there really isn't much one can say other than that, properly installed, the two should be completely independent of each other.
That said it seems that is not the case which takes us back to what none of us out here can know ... what isn't as you assume it should be.
What is most confusing to me is this statement:
The data files for both DBs are on ram. The objective is to find if we can double perf number with two instances.I have no idea what either sentence is intended to mean. The first because datafiles are not "on RAM" and the second because two instances will never double anything other than resource utilization and overhead.

How to create two independent index in the same RH project?

Hello everyone
I used Rh html 9.
I created a new index in my project to have two independent and different index, but the two index are connected. When I deleted one word in the new index, the same word is deleted in the first index.
When I've created the second index, I didn't choose the option "from an existing index", because I wanted a new and empty index but RH created a copy of the existing index and linked with the existing index.
It is possible toc reate a lot of different table of content and glossary but not different index ?
If someone can explain me why it doesn't work for index.
Thank you.
Florence

Hi there
If you click File > Project Settings > General tab, is the index set to have keywords in Topics or the Index file (HHK)?
If it's set for Index file (HHK) that would likely explain it because the keywords are stored directly inside the topics themselves.
If the setting is already for Index file (HHK) I'm a bit stumped and can only fathom that maybe you have stumbled across a bit of a RoboHelp bug. I've not tried using multiple indexes before. Perhaps I should try and see.
Cheers... Rick
Helpful and Handy Links
RoboHelp Wish Form/Bug Reporting Form
Begin learning RoboHelp HTML 7, 8 or 9 within the day!
Adobe Certified RoboHelp HTML Training
SorcerStone Blog
RoboHelp eBooks

I am using an NI PCI 6024 E board device for an analog output application. Can I generate two independent waveforms, one on each analog output channel?

I am using an NI PCI 6024 E board device for an analog output application. Can I generate two independent waveforms, one on each analog output channel? In attach I send a example of my vi to control one chanel, but i need to control both but with diferent waveforms.
Is the vi correctly programed to this propose?

Yes you should be able to do that. look at the signal generation examples shipped with LabView
You can create a 2 D array, with each row representing a wave form per channel. The number of points of the wave form (per row of the 2 D array) represent the number of points in the output buffer
The wave forms can have different amplitudes/shapes, and therefore they are independent in this sense.
However, you need to set the update rate,which is the same for both channels. The update rate together with number of points per buffer determines the frequency of the wave forms. This means the two wave forms will have the same frequency.
To have different frequencies, you need to have say, on wave form with one cycle per buffer, and the other waveform have 2 cycles
per buffer. in a case like that the frequency of the second channels is twice that of the first channel, and so on
The two wave forms are then not truly independent, they may have different amplitudtes/shapes, but related in frequency.

Gigabit EtherSwitch 10/100/1000BASE-TX autosensing EHWIC Traffic Marking and Shaping

Hi all,
i need to know an information about this module.
Gigabit EtherSwitch 10/100/1000BASE-TX autosensing EHWIC
I found on docs that it supports the SWDRR mechanism for queueing, but does it support also
traffic shaping and marking ?
i cannot find this info and i'd be thankful if someone knows it or can point me where this info is.
Thanks a lot
smaikol

ok, at least Jack is doing better now. Don't know why, I just play around with limits.conf, /etc/pam.d/su and deleted the content of /dev/shm directory.
Now the settings are the same as before, but I'm getting far less xruns and luckily without these disturbing plopps.
Last edited by redbit (2009-01-07 15:52:36)

How to create report with two independent queries and templates?

Hi,
I have a requirement where I have to use two queries in Data Template. Now, these queries are unrelated and I need to display data from these two queries in my report. Can anyone let me know how to do this?

Hi Thanks alot...It works.
Is it possible to create two independent SQL queries too and display the o/p from both queris in report?
Thanks alot in advance.

Fast array building from two independent acquisitions

Hi all,
I'm trying to figure out a way to build an array very quickly (up to 5 kHz) from two independent acquisitions. For the two acquisitions I have a counter input from an encoder and a normal analog input, the purpose is to correlate with high resolution a position to an output voltage. I can run each independently fast enough, but the problem I'm having is figuring out how to line up the two signals into a single array simultaneously and at a consistent rate (5 kHz) to write out to a file. My first hack was to read the two outputs into a while loop clocked by a wait timer, but the best I think I can do there is a 1 millisec wait which gives me no better than 1 kHz. Any ideas? Hopefully something simple I'm overlooking. Running LabVIEW 7.1 on a PCI-6036E card. Thanks in advance.

You're going to have to use hardware timing on the DAQ card and acquire multiple samples on each scan.
If you're using DAQmx (and you really should be), change the Read VI to
acquire multiple smaples from multiple channels. This single VI can
scan both channels and output a 2D array with each channels data in one
row of the array.
You'll also need to change your configuration setup to specify both channels and the smapling rate.
If you look in the Example Finder (Help menu>Find Examples...)
double click through "Hardware Input and Output">"DAQmx">"Analog
Measurments">"Voltage" you'll see several examples that do this sort
of measurment. Most of them only show how to acquire a single channel,
but can be easily modified to include a second channel.
Let us know if you need more help.
Ed
Ed Dickens - Certified LabVIEW Architect - DISTek Integration, Inc. - NI Certified Alliance Partner
Using the Abort button to stop your VI is like using a tree to stop your car. It works, but there may be consequences.

Which Mac's (current) can support two independant monitors?

I am trying to figure out which Mac's (current) can support two independent monitors? I am assuming that a MacBook Pro can only have one with its screen being open. This would make it handle two, but not independent. In clamshell mode would it be able to have two? I want to know if I have two identical monitors which Mac can display on both to have the screens show desktop 1 and desktop 2. Thanks

Depending on what Macbook Pro you have, you can have at least 1 external monitor, and with the newer ones you can have up to 2 external montiors.
The most recent models need a miniDisplay port adaptor for your generic monitor. You can get miniDisplay port to VGA, DVI, HDMI adaptors from Apple, or some 3rd parties, such a MonoPrice.com and other vendors.
Have you ever seen this dongle? Is it someting apple sells? Thanks
<http://store.apple.com/us/browse/home/shop_accessories/all_accessories/cables_do cks#!>
I own a mini-DisplayPort to DVI/HDMI adaptor from MonoPrice.com. I also own a mini-DisplayPort to DVI adaptor.
Apple sells them as well
To be clear, the Mac Thunderbolt ports accept a mini-DisplayPort adaptor.
You can use 2 Apple Thunderbolt 27" monitors on a recent Macbook Pro using a Thunderbolt cable to the first one, and then using another cable from the 1st Thunderbolt monitor to the 2nd Thunderbolt monitor.
I am unsure about whether you can do the 2 monitor trick with non-Apple monitors, or if you can mix and match a Thunderbolt display with a non-Apple monitor.
Old Macbook Pros may have had a DVI connector, or a mini graphic connector, depending on how old your Macbook Pro is.

SPARTAN-3E kit - '10/100 Ethernet Physical Layer Interface'

Hello,
I'm looking for using the '10/100 Ethernet Physical Layer Interface' on Spartan-3E kit with LABVIEW-FPGA. It seems the Spartan-3E kit with LABVIEW-FPGA driver doesn't support programming the Ethernet interface. Any idea to use (program) the Ethernet interface in LABVIEW-FPGA? For example, is it possible to use HDL node with Ethernet IP? Thanks in advance… Wedo,

No can do. This is not functionality incorporated with the current driver for the Spartan-3E. If you had some Xilinx IP that could interface with this, you could theoretically access it via a CLIP node, but i have a feeling it would be way more complicated than it's worth. If you need LabVIEW, an FPGA and ethernet functionality you should probably consider upgrading to a cRIO.
David_L | Certified LabVIEW Architect
LabVIEW Tools Network | LabVIEW Tools Network Developer Center

Is "Two independent 10/100/1000BASE-T Ethernet (RJ-45) interfaces" a switch?

Similar Messages

Maybe you are looking for