ISA550 Voice VLAN cannot connect to WAN?

Hi,
I just bought ISA550 and used the configuration wizatrd to set it up, mostly with defaults.
I mapped GE2 to VOICE VLAN/Zone, and although the SPA122 I connected to this port now gets an IP adress (10.1.1.100),it fails to register with SIP provider.
I have LB WAN set up (bandwidth), WAN1(GE1) Primary, WAN2(GE7) secondary, but not conecting WAN2 yet until I have configuration working.
I set ALG on for SIP (and tried it 'off') but nothing seems to work.
I also checked Firewall settings and added rule to 'permit' WAN to VOICE. There was only the other direction by default.
I have also not yet updated firmware, as I have only just elevated my access to allow encrypted downloads, biut will try that later this evening, out of hours.
Otherwise, any other suggestions gratefully received.
MTIA

I have now been able to get most of this working, but had to connect SPA122 to DEFAULT VLAN (GE3).
Added traffic selectors for this and some high priority (Q2) devices. Added QoS rules for these but if I added these to the default WAN_POLICY only those explicitly mentioned could access the WAN.
I then created a a new WAN POLICY without the default QoS rules, just the new ones, and this works!
However, I need to prioritise incoming traffic but only Q1 seems to be available for incoming, so currently only SPA122 has a rule (to mark Cos). Everything else is a free for all.
I have three devices I need to give Q2 on incoming traffic, so is there a way to do this, or is the traffic precedence 'inherited' from outgoing rules?
The documentation, both shipped CD and ESD, is not very clear on this. In fact, there are places where it is just plain wrong.
Otherwise, all seems to be going well. It is handling marginal circuits and LB better than my old router.
One last point. I need to report on WAN availability. I am remote logging to a Linux system to analyse syslog, but cannot find definitive log entries to determine WAN State (DNS LInk detection). Only physical port availability is shown explicitly (Line status - which also correctly triggers email alerts). I can see nothing similar for WAN State.
I use Splunk to analyse the logs, so could use fairly complex search pattern, if necessary.
MTIA
P

Similar Messages

Facetime between iPad2 and MacBook Air worked fine here in the USA. The iPad2 is now in Rome, Italy and we can't connect internationally. We both can hear the caller ringing in, but after accepting the call we cannot connect. No voice, no video.

Facetime between iPad2 and MacBook Air worked fine here in the USA. The iPad2 is now in Rome, Italy and we can't connect internationally. We both can hear the caller ringing in and can see who is trying to call, but after accepting the call we cannot connect. No voice, no video. iPad is successfully sending and receiving eMails, but no Factime connection What's up?

I am curious if possibly the hotel has some sort of VOIP block on. Have you tried Skype? Did you talk to the hotel staff? My husband is traveling to Milan in a couple of days and I wonder if he will run into the same issue. He has had no problems from Istanbul but he is staying in a corporate apartment there. If you find an answer please post back. Thanks

E1 to E1 DTI voice 30 channel transparent connection through WAN

Hello ,
I want to connect an E1 to E1 DTI voice 30 channel transparent connection through WAN
PSTN---E1 (router) Wan --- Wan (router) E1---PBX
Anyone can help with the above configuration?
I want the E1 connection to be transparent from the PSTN to the PBX for full voice usage.

That's about it, but you will also need to add the additional trunk to the existing trunk.dat file on the PGW.
http://www.cisco.com/en/US/partner/docs/voice_ip_comm/pgw/9/provisioning/notes/NASPKpgw.html#wp1035285

HP 7 Voice Tab - "Camera Error - Cannot Connect to Camera"

Hi, I am facing a Error on my HP 7 Voice Tab. when i try to open camera it showing Camera Error- Cannot Connect to Camera. I bout this in December 2014. I did few trouble shott like go to Setting -Apps- Camera- Force Stop, Claer Data, Clear Chache and then reboot the tab, But Still i have same error. Even i try installed new Camera apps from google Play Store, but Still the erroe remain same. I was thinking to to do Factory Data Reset. (The last option i Have) Please let me know if there is any other solution. Thanks,Raghu

Hey @JaishalCalicut ,
Welcome to the HP Forums!
I understand you're unable to connect to your Slate 7 Voice Tab to transfer data from your PCs.
Does the VoiceTab show up in Device Manager when it is connected?
Have you recently updated to KitKat?
How long is the cable you are connecting the devices with?
Is the device in MTU mode?
Clear all cache on the tablet: Settings > Storage > Cached Data. You should have the option to erase all the cached data here.
Hard reset: While the tablet is on, press and hold the power button for 8+ seconds to force shut down. Turn the tablet back on and see if that helps.
Factory reset: Make sure you backup any important files or information first. Settings > Backup & reset > Factory data reset.
Thanks!
Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
The Great Deku Tree
I work on behalf of HP.

802.1Q VLAN Tagging on DSL WAN Connection

Hi
Does anybody know if SRP527W supports 802.1Q VLAN tagging on DSL WAN connection for RFC1483 bridged connections?
Thanks
Justin

Hi Justin,
Sorry for the delay in responding. Yes, this feature is now supported by the SRP527W using the MR3 release. (Please see https://supportforums.cisco.com/docs/DOC-13853).
Andy

9951 phone - voice vlan connectivity lost

Hello,
I've 9951 phones that sometimes get the error LastOutOfServiceInformation=26 (close TCP due to a reconfiguration on a new voice Vlan).
I've checked the switch port status and modifications but nothing has been done that could lead to this issue. The user says it has no impact on the PC behaviour linked behind the phone. Phone is located on the LAN, close to the Cluster.
CUCM is 8.6.2
Phone firmware is sip9951.9-2-4-19
According to the logs, waht could be the reason ? DHCP renewal ? SIP fw bug ? Catalyst bug ?
Here are a few line console logs from the phone
6318 NOT 09:57:54.726464 CDP-cdpCacheClear(): vlan lost: proto: 1
6319 NOT 09:57:55.731141 CDP-configSelectVLAN(): 3 OP_USE_ADMIN_DFLT:5 oper:4096 cdp:4096 lldp:4096 admin:4096 mac:d4:a0:2a:83:b1:26
6320 NOT 09:57:55.750901 DHCP-dhcpRelease(): activeInterface: WIRED
6321 NOT 09:57:55.751044 DHCP-dhcpSendRel(): sending RELEASE...
6322 NOT 09:57:55.751173 DHCP-createSocket(): cesw0
6323 NOT 09:57:55.753565 CDP-Cfg_Idle_EvlldpDone_XIdle(): VVLAN [LLDP-IDLE] change: DHCP released
6324 NOT 09:57:55.757093 CDP-setVVLanConfig(): tmpVvlanId: 4096 dbgOldVvlan: 11 dscryProcInfo.vvlan: 4096
6325 NOT 09:57:55.760366 CDP-setVLanConfig(): tmpVlanId: 4096 dbgOldVlan: 41 dscryProcInfo.vlan: 4096
6326 NOT 09:57:55.762038 NETSD-netsdSignal(): EV_DHCP
6327 NOT 09:57:55.762169 NETSD-netsdSignal(): EV_VLAN
6328 NOT 09:57:55.762259 NETSD-netsdSignal(): forceDhcp= 1
6329 NOT 09:57:55.762342 PAE: -paeNetsdRcvMsg(1540): VLAN change: status: 0x0 : No such file or directory 6318 NOT 09:57:54.726464 CDP-cdpCacheClear(): vlan lost: proto: 1
6319 NOT 09:57:55.731141 CDP-configSelectVLAN(): 3 OP_USE_ADMIN_DFLT:5 oper:4096 cdp:4096 lldp:4096 admin:4096 mac:d4:a0:2a:83:b1:26
6320 NOT 09:57:55.750901 DHCP-dhcpRelease(): activeInterface: WIRED
6321 NOT 09:57:55.751044 DHCP-dhcpSendRel(): sending RELEASE...
6322 NOT 09:57:55.751173 DHCP-createSocket(): cesw0
6323 NOT 09:57:55.753565 CDP-Cfg_Idle_EvlldpDone_XIdle(): VVLAN [LLDP-IDLE] change: DHCP released
6324 NOT 09:57:55.757093 CDP-setVVLanConfig(): tmpVvlanId: 4096 dbgOldVvlan: 11 dscryProcInfo.vvlan: 4096
6325 NOT 09:57:55.760366 CDP-setVLanConfig(): tmpVlanId: 4096 dbgOldVlan: 41 dscryProcInfo.vlan: 4096
6326 NOT 09:57:55.762038 NETSD-netsdSignal(): EV_DHCP
6327 NOT 09:57:55.762169 NETSD-netsdSignal(): EV_VLAN
6328 NOT 09:57:55.762259 NETSD-netsdSignal(): forceDhcp= 1
6329 NOT 09:57:55.762342 PAE: -paeNetsdRcvMsg(1540): VLAN change: status: 0x0 : No such file or directory
Thanks,
JC

Hi Jean,
Could be hitting the bug
CSCuf93609 Bug Details
9951 loses audio on active call when link with pc port is disconnected
Symptom:
When the cable between 9951 and the pc connected to the pc port gets disconnected during an active call there is no audio anymore, the call stays active.
Conditions:
Running firmware version 9.3(2)ES10 or ES12, does not happen with 9.3(2)
regds,
aman

Connect router/firewall to a voice vlan

Hi
I need to connect a router to a voice vlan port to allow all voice traffic to exit the VLAN without having to transverse onto the data vlan and use its gateway.
However any device I assign to a voice vlan port is ignored by the switch if it isn’t a phone. This must be a common question and I have one worded differently in the voice forum but as it seems a basic networking question I thought I would add it here too.
Switches – sg500x
Router/Firewall – ASA5512
Desperate for some direction on this. Not cli but general guidance on how this should work.
Thanks

Hi,
Not familiar with sg500x, but if you have 2 vlans on the sg500x switch, you need to make the connection to ASA-5512 a trunk port, so both voice and data vlan can reach it. The other option is to use a separate physical link (one for voce traffic and one for data traffic) from the switch to the firewall and add each vlan to a proper port/link.
HTH

TS1717 I have older version of itunes on Windows Vista, when i check for updates it states it cannot connect to itunes update server even though i am connected to the internet, i have an iphone that has songs in the cloud and i wan to add them to my libra

I have older version of itunes on Windows Vista, when i check for updates it states it cannot connect to itunes update server even though i am connected to the internet, i have an iphone that has songs in the cloud and i want to add them to my library?

Try updating your iTunes using an iTunesSetup.exe (or iTunes64Setup.exe) installer file downloaded from the Apple website:
http://www.apple.com/itunes/download/

Cannot connect a voice or video call succesfully t...

Asus 10.1 - transformer padTF300T - stock Android 4.2.1 - bt WiFi (home/office network), Skype v5.0.0.52727.
From laptop to tablet & vice versa,Voice & Video calls connect for a few seconds and then everything freezes. Text is ok. 3G iphone to same laptop everything works. Can you advise anything please?

Same to me

802.1x and Voice VLAN

I had read articles on cco, and I believed for the same switch port we can have 802.1x configure and the voice vlan configure. It mean the IP phone is connect to the switch port with 802.1x configured, but the phone will not autheticate, only the workstation connect to phone data port will get authenticate.
I had configured 802.1x and test with notebook logon and able to access the network. Now I would like to test the notebook attached to IP phone data port, and the phone connect to switch port configure with 802.1x. But I failed to add voice vlan commmand. Why ?
interface GigabitEthernet9/48
description temporary port
switchport
switchport access vlan 12
switchport mode access
no ip address
dot1x port-control auto
spanning-tree portfast
CIG01-ENT-SW1(config-if)#switchport voice vlan 14
Command rejected: Gi9/48 is Dot1x enabled port.

Using IEEE 802.1x Authentication with Voice VLAN Ports
A voice VLAN port is a special access port associated with two VLAN identifiers:
?VVID to carry voice traffic to and from the IP phone. The VVID is used to configure the IP phone connected to the port.
?PVID to carry the data traffic to and from the workstation connected to the switch through the IP phone. The PVID is the native VLAN of the port.
In single-host mode, only the IP phone is allowed on the voice VLAN. In multiple-hosts mode, additional clients can send traffic on the voice VLAN after a supplicant is authenticated on the PVID. When multiple-hosts mode is enabled, the supplicant authentication affects both the PVID and the VVID.
A voice VLAN port becomes active when there is a link, and the device MAC address appears after the first CDP message from the IP phone. Cisco IP phones do not relay CDP messages from other devices. As a result, if several Cisco IP phones are connected in series, the switch recognizes only the one directly connected to it. When IEEE 802.1x authentication is enabled on a voice VLAN port, the switch drops packets from unrecognized Cisco IP phones more than one hop away.
When IEEE 802.1x authentication is enabled on a port, you cannot configure a port VLAN that is equal to a voice VLAN.
Waht kind of switch do you have? In 3550 I can configure the port for both vvid and pvid:
interface FastEthernet0/1
switchport access vlan 3
switchport mode access
switchport voice vlan 2
no ip address
dot1x port-control auto
spanning-tree portfast
end
Nevertheless, as the statement above indicates, the port will need to be configured for multi-host in order the PC behind the phone get autehntication:
under the interface configure "dot1x host-mode multi-host"
Nevermind, I just realized that you might have a 5600 running native, checking the configuration guide and realese notes it does not looks like dot1x and vvlan can play together in that platform.

Setting up a Test Voice VLAN for Lync 2013

I want to set up a second voice vlan to be a test vlan.
In the current situation the customer has voice and data running on vlan1. The customer insist on taking incremental steps to improve QoS. I have advocated separated vlans for voice and data. They just want to move everything (phase 1) to a different
vlan. They want to see how getting all traffic of vlan 1 will improve there performance. Again, I recommended the best practice, they want to try this approach first.
I am conducting a pilot test with just one cx600 IP phone. and a single switchport. I created a new vlan99 using VTP. I configured the switchports on the Cisco 2960-x switch as follows.
#switchport mode access
#switchport access vlan 99
The phone gets its correct vlan id, and pulls its IP from the correct dhcp scope. However the phone displays "connecting with the lync server" for a long time, then "connecting to download its certificates". This takes a long time then fails.
If I change the switchport back to vlan1 it works fine. What can be the problem? Does the vlan99 need to be defined on the lync server? How many vlans can be supported by Lync 2013?
Thank you,
gigiu

Did you set the VLAN Configuration for Lync Phone Edition?
You can check the following links:
http://blog.schertz.name/2011/01/manual-vlan-configuration-for-lync-phone-edition/
http://www.bricomp.com/blogs/post.cfm/dedicated-voice-vlan-for-lync-devices
Note: Microsoft is providing this information as a convenience to you. The sites are not controlled by Microsoft. Microsoft cannot make any representations regarding the quality, safety, or suitability of any software or information found there. Please
make sure that you completely understand the risk before retrieving any suggestions from the above link.
Lisa Zheng
TechNet Community Support

PC Voice VLAN Access

Hi all,
I've just been testing using Cisco IP Phones with the Linksys SRW224P switch (which do not support CDP and automatic voice VLAN assignment). It's all pretty straightforward, however, I found I needed to enable the "PC Voice VLAN Access" setting for the IP phone to get the PC (attached to the phone) communicating on the network. With this setting disabled, the PC cannot communicate on the network, even if the correct data VLAN ID is configured in the "PC VLAN" setting on the phone. This same issue is also replicated if I disable CDP on a Cisco switch and manually configure the voice VLAN ID on the phone.
Any ideas as to why this is the case? My understanding of the PC Voice VLAN Access setting is that it enables an attached PC to access the voice VLAN (i.e. tag frames with the voice VLAN ID and send on the voice VLAN, and receive frames on the voice VLAN). The traditional port mirroring issues associated with this setting aren't an issue nowadays, as you now have the additional "Span to PC Port" setting to control this.

Hi Eric,
Please make sure you are sniffing the correct interface. For example, if you have more than one interface (such as Wireless Ip address or VPN
connection) select the one you want to sniff. Please check the following link, it shows you how to set up a sniffer capture using wireshark:
http://wiki.wireshark.org/CaptureSetup
Regards,
Teresa.
If you find this post helpful, please rate! :)

SG300 voice vlan problem with UC520

Hi Forumers'
My problem statement:
- refere to attached topology.png, this is how my network structure look like
- the IP phone after boot cannot get connected, so it can't download the XML config file from UC520. suspicious switching problem.
- my configuration shown at topology.png and my vlan voice config show as voice vlan setting.png
- My requirement is SG300 switch single switchport to carry vlan data and vlan voice.
- what is the trunking mode for voice VLAN siwth a IP phone+data should i configure? is it switchport voice vlan vvid, switchport voice vlan dot1p, switchport voice vlan untagged or switchport voice vlan none to suite above requirement?
thanks
Noel

Hello Noel,
Sorry for the late reply, things have been quite hectic around here lately
1. Why use trunk? the UC520 only have vlan voice (vlan 20)
Do you mean that the data VLAN is handled by another device ? Still I would leave it as a trunk in order to be able manage the UC through the data VLAN. (Unless for security or other reasons you would choose otherwise of course)
2. The UC520 got CUE (voice messaging), how should i design the service module uplink to the core switch?
Nothing in particular has to be done for this, CUE is handled and routed inside the UC520, the CUE vlan (default ID =90) is only used if you have another CUE in the network
1. i guess i did this: swithcport tagged vlan 20, untagged vlan 10. is it ok for this setting?
If the Voice Vlan on the switch and on the UC520 has been defined as VLAN 20 (default = VLAN 100) this is perfect. Verify if both on the UC and on the switch, the voice VLAN ID is set to 20.
1. so if i just point the phone to vlan 20 (vlan voice), should i create the LLDP network policy?
If you are ready to configure the VLAN manually on the phone, you don't need the LLDP policy, that is correct.
The LLDP policy is being used for having the phones automatically choose the VLAN you defined, so you don't need to set it manually.
Hope this answers your questions ?
Best regards,
Nico Muselle
Sr. Network Engineer - CCNA

Cannot connect to ASDM on ASA 5505 over https

Problem: Cannot connect to ASDM on ASA 5505 when vlan1 network is changed from the factory default.
Hi all. I am just getting started on a new ASA 5505, working it in a test lab environment. I ran thru the initial setup wizard. During that time I specified a name for Vlan1 (changed from 'inside' to 'INTR-NET'), modified the Vlan1 IP address to use DHCP, and then populated the Device Config Access table with entries corresponding to the entire Class B network here on the local intranet. I don't recall if the factory-default network was already populated, but if it wasn't I added it as 192.168.1.0/255.255.255.0
I then saved the config, and verified that the ASA got a dhcp address using the RS-232 console. I then reconfigured the laptop I have plugged into port 0/1 with it's normal address on the intranet and discovered that I couldn't reconnect to ASDM. The ASDM client times out, and a web browser opened to https://(ASA5505's dhcp addr) fails as well.
I then used the console to add another http IP address matching the specific IP address (xxx.240.113.129/255.255.255.255) which the laptop is set for, to the list of permissible admin connections, but saw no difference.
This issue is much the same as was reported in this prior forum posting:
http://forums.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Security&topic=General&topicID=.ee6e1f8&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.2cc16cb8/4
EXCEPT that I was already aware the admin IP address(es) needed to be registered to enable access via SSH/Telnet/HTTPS.
And, I did that step, but it is not working. I have tried adding various combinations of network ranges in the device config access list, including the specific subnet that the lab's dhcp server assigned to the ASA 5505 (xxx.240.112.0/255.255.254.0), but there is no difference. I can traceroute to the laptop and ping the Vlan1 interface from the laptop, but the https ASDM (and ssh connections too) are not successful. This is very frustrating.
The device is brand new, I see that upon boot it loads asa724-k8.bin, and the software banner says Cisco Adaptive Security Appliance Software Version 7.2(4)
Note also that, from the RS-232 console, if I reset the IP address to the static, factory default (192.168.1.1) and manually config my laptop on the same subnet, then ASDM makes the connection. Just like out of the box. But when I put it back onto our intranet and verify the DHCP lease, then ASDM is a no go.
Can you think of what I've missed?

Good question. Let me add that info plus related Vlan config details:
ASA5505A# show ip
System IP Addresses:
Interface Name IP address Subnet mask Method
Vlan1 INTR-NET XXX.240.112.92 255.255.254.0 DHCP
Vlan2 VoIP 172.26.99.1 255.255.255.0 manual
Vlan3 dmz-unused 192.168.99.1 255.255.255.0 manual
Current IP Addresses:
Interface Name IP address Subnet mask Method
Vlan1 INTR-NET XXX.240.112.92 255.255.254.0 DHCP
Vlan2 VoIP 172.26.99.1 255.255.255.0 manual
Vlan3 dmz-unused 192.168.99.1 255.255.255.0 manual
ASA5505A# show switch vlan
VLAN Name Status Ports
1 INTR-NET up Et0/1, Et0/2, Et0/3, Et0/4
2 VoIP down Et0/5, Et0/6, Et0/7
3 dmz-unused down Et0/0
ASA5505A#
ASA5505A# config t
ASA5505A(config)# show running-config http
http server enable
http XXX.240.0.0 255.255.0.0 INTR-NET
http 192.168.1.0 255.255.255.0 INTR-NET
http XXX.240.113.129 255.255.255.255 INTR-NET
ASA5505A(config)#
ASA5505A(config)# show running-config ssh
ssh 192.168.1.0 255.255.255.0 INTR-NET
ssh XXX.240.0.0 255.255.0.0 INTR-NET
ssh timeout 5
SECURITY LEVEL IS 100 ON Vlan1 and Vlan2, 50 on Vlan3, and traffic is restricted from Vlan3 to Vlan1 because this is the basic license.

Win 7 PC cannot connect to Time Capsule - despite flawless I'net connection

Hi, strange thing and I'd appreciate if someone knew a trick to solve it:
Although my Windows notebook can connect to the internet via our Time Capsule (WPA2 key, AES encryption) without any problems for a long time now, I cannot connect to it via AirPort even with the correct WPA key.
When running the AirPort utility I can see our TC with its name and IP address (10.0.1.1 as usual, I think) in the main view. After clicking "Manual Setup" or "Continue" in the main view, AirPort asks for the password.
After entering the password (same as the one that is in my settings for the WLAN connection via TC, of course), *TC REFUSES TO CONNECT* and the *"Enter password" window will appear over and over again*. No specific error message given.
The WLAN connection has been set up using the MacBook (I once read this could be a problem). Working proberly
all the time, though.
Tried deactivating both firewall and virus protection of my Norton security package on my Lenovo - no effect.
Background:
We intend to use an external USB hard drive which is connected to our Time Capsule. After TC has moaned that the drive had to be "repaired", we created partitions for Mac (OS X) and Windows (FAT) partition from the MacBook.
The MacBook can access the drive and partitions. Fine.
The Windows 7 notebook won't show the hard drive nor the Time Capsule. Thus, I have installed AirPort utility (V 5.5.1) to get access to the USB hard drive. And there I am - kinda stuck halfway...
Hardware setup:
Lenovo ThinkPad X61, Windows 7 Pro
MacBook, OS X 10.5.8
Time Capsule
1.0TB Buffalo Drive Station USB 3.0 plugged into Time Capsule
Help would be very much appreciated!
Thanks a lot,
Mark

I found something that worked for me. I got Error Number 53 when trying to connect to my time capsule using Airport Base Station Agent with windows vista. I think the issue is allowing your time capsule to be accessed over Bonjour; I think this feature is disabled by default. Well, here is what I did (also, this may answer the question for those of you who are confused to why it asks for a username/password when you attempted to map the time capsule's hdd) -
In Airport Utility: Airport >> Time Capsule
- Click "Edit..." and check the "Use dynamic global hostname" box.
- Enter in the info (for hostname, I used the same name as the local Hostname (at the top of that window, for user/password -- The info you enter here is the same info you must enter when you are prompted to, that is if you try to map the time capsule's hdd)
- Click "OK"
In Airport Utility: Disks >> Files Sharing
- Make sure "Share disks over WAN" is checked AND make sure "Share disks over the Internet using Bonjour" is checked as well.
- Click OK.
In Airport Utility: Click "Update", let it reset, and try accessing the Time Capsule via Airport Base Station Agent as you usually would/or mapping the harddrive"
In summary, since vista uses Bonjour, you must make sure your time capsule is 'Bonjour-accessible'
I Hope this solution alleviates a lot of people's problems!!!
Oh yea, this solution worked with firmware 7.4.1
AND...prior to trying this method, I did enable NETBIOS. It was enabled while I did this solution (and still is). I haven't tried it with it disabled (well maybe not disabled - it's on automatic by default).

ISA550 Voice VLAN cannot connect to WAN?

Similar Messages

Maybe you are looking for