ISA550

Dear support,
I've previously purchased the ISA 550 and would like to aggregate 2 HDSL links to benefit from load balancing and redundancy. Kindly advise if the ISA 550 is capable of that.
Regards

It is capable.  You may wish to see this before making purchase decision though:
http://www.cisco.com/en/US/products/ps11752/prod_eol_notices_list.html

Similar Messages

  • PAT issue on an ISA550

    I need a little assistance.  I am using an ISA550 with a Static IP block assigned using Static NAT and everything thing seems fine EXCEPT for 1 program.  This program needs port 443 mapped to port 22 on the private address however I can't determine how to do that.  The server that program is on is assigned a Static address so I need to access it through the public address.  I hope this is clear.  Does anyone know how to do this?

    Jim,
    Thanks for your reply.  I have tried all the examples on those pages to no avail.  The issue I run into is that I am using Static NAT and when I run a scan on the public or private address of any server, I show these ports to be open.  I am trying to configure a product that is designed to be port mapped from 443 to 22, however when I try Dynamic PAT, Port Forwarding, Triggering, Advanced NAT, etc., I get an error that the port is configured using Static NAT (which is as it should be) but I am stumped.  This is the error I am getting.  
    External port 443 is closed. Manually configure your broadband router to map external port 443 (TCP) to port 22 on internal host.
    Since I am using Static NAT, this should happen automatically.

  • How to asign some content filtering policies to a wan port ISA550

    Hi, I have a Cisco ISA550, and we are trying to make some url's rules for the network. I have established a policie, with some content and url's, but now I need to asign them to a configurable wan port. What I have do is:
    1. Go to firewall and open content filtering policies
    2. Generate a new filtering policie. (named: diarios)
    3. Load the policie with some URL (all are enabled with the tickets)
    4. go to Policy to Zone Mapping and change the LAN zone. Now using "diarios"
    5. Content filtering turned ON
    6. Go to Advance settings and configure it.
    everything saved and it works. But now I need to asign this rule only to wan port #3.
    Can someone help me please?
    Thanks a lot.

    Open the Trace Log panel in Scout - it shows you all the trace messages for the selected frames (in a console-like view). If you select all frames, you can see all trace messages for the entire session.
    See Figure 27, here:
    http://www.adobe.com/devnet/scout/articles/adobe-scout-getting-started.html

  • ISA550 Voice VLAN cannot connect to WAN?

    Hi,
    I just bought ISA550 and used the configuration wizatrd to set it up, mostly with defaults.
    I mapped GE2 to VOICE VLAN/Zone, and although the SPA122 I connected to this port now gets an IP adress (10.1.1.100),it fails to register with SIP provider.
    I have LB WAN set up (bandwidth), WAN1(GE1) Primary, WAN2(GE7) secondary, but not conecting WAN2 yet until I have configuration working.
    I set ALG on for SIP (and tried it 'off') but nothing seems to work.
    I also checked Firewall settings and added rule to 'permit' WAN to VOICE. There was only the other direction by default.
    I have also not yet updated firmware, as I have only just elevated my access to allow encrypted downloads, biut will try that later this evening, out of hours.
    Otherwise, any other suggestions gratefully received.
    MTIA

    I have now been able to get most of this working, but had to connect SPA122 to DEFAULT VLAN (GE3).
    Added traffic selectors for this and some high priority (Q2) devices. Added QoS rules for these but if I added these to the default WAN_POLICY only those explicitly mentioned could access the WAN.
    I then created a a new WAN POLICY without the default QoS rules, just the new ones, and this works!
    However, I need to prioritise incoming traffic but only Q1 seems to be available for incoming, so currently only SPA122 has a rule (to mark Cos). Everything else is a free for all.
    I have three devices I need to give Q2 on incoming traffic, so is there a way to do this, or is the traffic precedence 'inherited' from outgoing rules?
    The documentation, both shipped CD and ESD, is not very clear on this. In fact, there are places where it is just plain wrong.
    Otherwise, all seems to be going well. It is handling marginal circuits and LB better than my old router.
    One last point. I need to report on WAN availability. I am remote logging to a Linux system to analyse syslog, but cannot find definitive log entries to determine WAN State (DNS LInk detection). Only physical port availability is shown explicitly (Line status - which also correctly triggers email alerts). I can see nothing similar for WAN State.
    I use Splunk to analyse the logs, so could use fairly complex search pattern, if necessary.
    MTIA
    P

  • ISA550 I can't configure it at all

    Hi,
    I've just installed a firewall ISA550 on my network, but when I try to update the firewall's anti-virus it gets an error: "Anti-virus failed to get signature information. Please check Cisco.com and try again". What I have to check ?
    When I try to check my account settings inside the firewall (Devide management -> Cisco services&support -> Cisco.com Account), it gets another error "Check the WAN connection and try again". Maybe there's something that I didn't configured that blocks my internet ? Or maybe are the cables..
    The network consists in 1 router then the firewall and then a switch. So how have to be the cables?
    Anyone knows some option that it's very important to configure on the firewall in order to have internet? Maybe by default the firewall blocks the internet, but i have permited the traffic on the ACL.
    So please if anyone has any idea or maybe any doubt in the configuration that I have, please tell me.
    Thanks.

    I didn't even know what that was until you mentioned it
    I've had my mac for about a month. It worked! Thanks heaps

  • ISA550 import wan ip list to block access

    I'm thinking of getting an ISA550.
    I would like to know if there is a way to import a list of ip addresses to either allow access to vnc services.
    If I can import this list -the allow would be all usa based ip addresses- what format must the list be in?
    If this product will not do this what cisco product will?
    Is there a software component I will need to buy beyond the ISA550 or another appliance if the ISA550 is not the right device?
    If no software is necessary at this time, can I buy it later if my client's needs expand?

    IP A Camera Server
    IP B  Camera 1 port 80
    IP C Camera 2 port 80
    I want to block everyone from accessing IP A, IP B and IP C but a few people; They will need to access the server to see the cameras instead of the cameras directly. I need to have IP B and IP C open to them as well. 
    At this time anyone can type the IP address of a camera in the web browser and see it.
    Thanks
    Laren

  • Schedule web url filtering in isa550

    Hello,
    This is my first experience using isa550 security appliance.  i would like to schedule the web url filters: in example accept or deny some websites or url categories on certains hours, or days.
    i see that the schedules can be applied on firewall rules, but i can't see how to apply theses schedules on web url filtering. when i link the web url policy to zones i don't see anything about shedules .
    can you help please ?

    I can confirm what you are seeing. There are schedules on the Application Control, for example, but not the web filter. One possible consideration with this is though you may want to allow some websites during certain times (Facebook over lunch hours for example) there would probably be blocked websites you would want to allow ever (child porn for example) ever. Since only one policy can be applied per Zone, until multiple policies can be applied to a Zone, you probably wouldn't want to turn off ALL web filtering for a Zone ever.
    I'd recommend trying to leverage Application Control instead. You can apply multiple policies to a Zone so you could create a policy that includes everything that is blocked always and another that has content you'll allow during a schedule. The apply both policies to the same Zone and ensure your schedule policy is above your always block policy so that if there's ever a conflict the schedule policy would apply first and allow the traffic during allowed times. That's unless your internal security policies dictate otherwise.
    Sent from Cisco Technical Support iPhone App

  • ISA550 and multiple subnets?

    Just picked up a ISA550 and have been playing around with it a bit but seem to be having some trouble.  I have two LAN subnets in my small business with approx 10 hosts per subnet.  I'd like to use the ISA550 to route between them (and to the internet) but can't seem to figure out how.  Is it just as simple as creating two VLANS?  Can the ISA550 route VLAN traffic?
    With my old RV042G, I had the option to setup multiple subnets inside the setup menu but I don't see any such area with the 550.  Any help would be appreciated!

    Each port is configurable.  So you just need to create a VLAN name and IP/Subnet for each port.
    For example, if you only have two subnets then you would do this:
    Port 1 IP address/network mask - 192.168.1.0/24
    VLAN  name for Port 1 - office_network
    Port 2 IP address/network mask - 192.168.2.0/24
    VLAN name for Port 2 - server_network

  • ISA550 trial license

    Hi to all,
    Is there a possibility to find a trial security license just to demonstrate the ISA550 appliance, without activating the 1 year that is included? We need this just for demo purposes and we want to sell the appliance afterwards so the client will have the whole 1 year security subscription.
    Thanks

    Hi Kristina, thank you for using our forum, my name is Johnnatan I am part of the Small business Support community.
    I have a question for you, what kind of license you are looking for?
    I hope you find this answer useful
    “Please rate useful posts so other users can benefit from it”
    Greetings, 
    Johnnatan Rodriguez Miranda.
    Cisco Network Support Engineer.

  • ISA550 Service Groups

    I am configuring my ISA550 and cant seem to utilize Service groups when creating NAT policies or port forwarding.  Any Help?
    Firmware Version:1.1.14

    Good morning
    Thanks for using our forum
    Hi Jon, my name is Johnnatan and I am part of the Small business Support community. If you want to see the Service group option, you have to configure it first. The security appliance supports up to 64 service groups. A service group can include up to 64 service members. In order to configure it, please follow these steps:
    STEP 1 Click Networking > Service Management.
    STEP 2 In the Service Groups area, click Add Group to add a new service group.
    Other options: To edit an entry, click the Edit (pencil) icon. To delete an entry, click
    the Delete (x) icon. To delete multiple entries, check them and click Delete.
    The Service Group - Add/Edit window opens.
    STEP 3 Enter the name for the service group in the Group Name field.
    STEP 4 To add the services to the group, select the services from the left list and click the
    right arrow.
    STEP 5 To remove the services from the group, select the services from the right list and
    click the left arrow.
    STEP 6 Click OK to save your settings.
    STEP 7 Click Save to apply your settings
    If you already configured your device and you can´t see the option, try using another browser.
    I hope you find this answer useful,
    *Please mark the question as Answered or rate it so other users can benefit from it"
    Greetings,
    Johnnatan Rodriguez Miranda.
    Cisco network support engineer.

  • ISA550 DMZ for VOIP

    Hi !
    I have a ISA550 and I want to make a DMZ LAN with VOIP SIP Phones ! This DMZ Subnet schould not be patet and should ve accessed from the Internet only form a certian Subnet !
    The DMZ Network is statc routed to the ISA 550 WAN Interface from outside !
    Here my Config:
    ACL Rule
    From WAN to DMZ  Services any  Source Managment  Destination Address DMZ-Network   enable
    Dynamic PAT
    disable DMZ
    Advanced NAT:
    From DMZ to WAN1 Original DMZ to WAN1 Orgnal Source DMZ-Network  Orginal Destination any any Translatated Source DMZ-Network any any
    The config above not work !  What is wong ?
    Also I want to use QOS with strict priority Queuing for this Network  -> How should I do this -> Protocol RTP and SIP
    Thanks !
    kind regards
    kristoferus

    Kristoferus,
    To accomplish what you are wanting shouldn't require any special ACL Rules or NAT configuration.  The reason for this is because all communications are initiated from the SIP Phones to the VoIP provider.  Once the SIP Phone connects to the VoIP provider's network, all traffic is managed over that established connection.  So the VoIP provider's network will never actually initiate a connection into your network and thus you don't need any special NAT configuration to allow them access.
    Since the VoIP provider is in a lower security level Zone (WAN), the VoIP DMZ will have, by default, unlimited access to the WAN, and by default the WAN will explicitly allow back through any traffic initiated from a higher security level Zone (VoIP DMZ).  So this is what I would suggest doing.
    Assumptions
    You mentioned source Management in your ACL Rule.  I'm assuming Management is the Address Group that contains the VoIP provider's subnet.
    Steps to complete
    Delete the ACL Rule you created and referenced above
    Delete the Advanced NAT statement you created and mentioned above
    Under Dynamic PAT, enable for the VoIP DMZ as well
    Under Application Level Gateway, ensure SIP Support is unchecked
    Under Networking -> Ports -> Physical Interface, ensure the DMZ VoIP VLAN is applied to the appropriate interface
    If the only thing attached to this port is an external switch that only phones plug into, then ensure the mode is set to Access and that the only VLAN on this port is the VoIP DMZ.
    If a switch is connected to this port and that switch is shared by both phones and devices in other VLANs...
    Ensure the external switch supports VLANs
    Set the Mode to Trunk and add the appropriate VLANs to the port
    Configure the external switch ports to include the correct VLANs on the associated ports to ensure that phones are being placed in the VoIP DMZ VLAN and not the default.
    Once you have all of this setup, test the phones and they should be working.  If they are proceed to the next step to lock down security.  If not, do not proceed to the next step as it will only add complexity to troubleshooting.
    Limit SIP Phones to only have access to VoIP provider
    Create an ACL Rule...
    From Zone:  VoIP DMZ
    To Zone:  WAN
    Services:  ANY
    Source Address:  VoIP DMZ Network
    Destination Address: Management (Based on my assumption above)
    Log:  On
    Match Action:  Permit
    Create an ACL Rule...
    From Zone:  VoIP DMZ
    To Zone:  WAN
    Services:  ANY
    Source Address:  ANY
    Destination Address: ANY
    Log:  On
    Match Action:  Deny
    Once both ACL Rules are created, ensure the first ACL Rule is before the second ACL Rule.
    The combination of these rules in the correct order will allow traffic from the SIP Phones to the VoIP provider and then block the SIP Phones from accessing anything else.
    You should be done and working at this point.  If so, let me know and we can move on to QoS.

  • ISA550, ISP VLAN tagging?

    Hi,
    Just purchased an ISA550 to replace the ISP's router. I've been told that they use VLAN 101 for internet traffic. My public IP address is allocated from ISP's DHCP server.
    So I need to configure WAN1 for VLAN 101, but since I don't have the IP address/subnet how do I configure the IP setting for WAN/VLAN 101?

    Hi Wei,
    That requires username/password, which isn't needed. It's a regular Ethernet WAN connection with VLAN tagging. The ISP provides triple-play this way. Their Sagem routers supports it out-of-the-box

  • ISA550 - Multiple Router Question

    I have a routing issue with a 2nd router that I hope someone can suggest a solution. Since I have the ISA550 - wired version only - I am adding a wireless router to the network.  I have a /29 block available from my ISP and the router needs a static IP address so I thought that I could static route? to the WAN of the ISA550.  The router has it's own NAT, DHCP, etc., but I need it to route to the internet without disrupting the VLANS already setup in the ISA550.  I have been using Static NAT for other devices that need a public IP, but I'm not sure how to deal with the wireless router. 
    Any suggestions?

    Based on the information you've provided and considering the possibility of Static NAT'ing an IP to itself, it might be possible to do this without double NAT'ing.  I'll give you 2 scenarios.  One which might work without double NAT'ing, but will cost you 2 IPs.  The second is with Double NAT'ing and will not cost you any IPs.  Both of my scenarios assume the ISP uses 74.10.10.1 and you have 74.10.10.2 - 74.10.10.6 available for your use.  If that is not accurate, you can adjust IP Addressing accordingly.
    Scenario 1
    ISP Modem -> ISA WAN (74.10.10.2 / 255.255.255.252)
    ISA LAN (74.10.10.5 / 255.255.255.252) -> Airport (74.10.10.6 / 255.255.255.252) -> Wireless Clients (10.0.2.x)
    Configure a Static NAT entry in the ISA to translate 74.10.10.6 to 74.10.10.6
    Projected end result is that the internet would see the Airport as 74.10.10.6
    In Scenario 1, you would lose the use of the IPs 74.10.10.3 and 74.10.10.4 as they would be consumed by subnetting your 1 subnet into 2 so you could assign them to different interfaces on the ISA.  Any other hosted services would have to use the 74.10.10.2 IP.
    Scenario 2
    ISP Modem -> ISA WAN (74.10.10.2 / 255.255.255.248)
    ISA LAN (192.168.100.1 / 255.255.255.0) -> Airport 192.168.100.2 / 255.255.255.0) -> Wireless Clients (10.0.2.x)
    Configure Static NAT entry in the ISA to translate 192.168.100.2 to 74.10.10.6
    Projected end result is that the internet would see the Airport as 74.10.10.6
    In Scenario 2, you would retain all your IPs however 10.0.2.x clients would be NAT'd to 192.168.100.2 which would then be NAT'd to 74.10.10.6 resulting in double NAT'ing.
    If you'd like to discuss this further before beginning and feel it would be better discussed over the phone, send me a PM and I'll give you a number you can reach me on.
    Shawn Eftink
    CCNA/CCDA
    Please rate all helpful posts and mark correct answers to assist others searching for solutions in the community.

  • Installing Intermediate SSL Certificates on ISA550?

    Been trying to figure this out for days with no luck.  Godaddy issued me two certificates.  One is the FQDN.crt for my domain and the other is the intermediate certificate that is responsible for completing the chain of trust.  However, I haven't been successful with installing the intermediate .crt onto my ISA550.   I was able to install the FQDN.crt using the guide here: http://www.cisco.com/en/US/docs/security/small_business_security/isa500/technical_reference/certificates/isa500_installing_certs_appnote.pdf but that doesn't talk about installing chained certificates at all.
    I have seen some guides talking about how to do this with ASA devices but it seems those don't apply to the ISA.  This is mostly because there is no CLI with the ISA (as there is with the ASA) and also I don't see way to import/export private SSL keys from/to the ISA.
    Ideas?

    Hi Rodman, thank you for using our forum, my name is Johnnatan I am part of the Small business Support community.  I apologize for this inconvenience, but in this case can you please reach out to our Small Business Support Center and open a Service Request to address this issue? One of our Engineers may be able to work with you and diagnose the root cause. You can find the appropriate contact information for SBSC in the below link.
    http://www.cisco.com/en/US/support/tsd_cisco_small_business_support_center_contacts.html
    I hope you find this answer useful,
    “Please rate useful posts so other users can benefit from it”
    Greetings, 
    Johnnatan Rodriguez Miranda.
    Cisco Network Support Engineer.

  • ISA550 SNMP Problem

    My client wants to use MRTG to track traffic out to the Internet.  The tools within the ISA550 are good but they need something more detailed.  I have setup MRTG before with a Cisco router and it worked great.  However, this time it is not working so good with the ISA550.  The cfgmaker program used to create a configuration file for MRTG reads the ISA550 loopback okay and reports the interface speed, but the other interfaces come up with a speed of 0 (zero).
    Is there anything special I need to do with the ISA550 to get SNMP to read interface speed?  MRTG uses SNMP v1 or v2 and that is what the configuration of SNMP on the ISA550 is set to.                  

    I have additional information about this issue.  I did an "snmpwalk" on the Cisco ISA550 and the results (edited for relevancy) are below.  I also did a "snmpwalk" on a Cisco SG200 switch.  The Cisco router does not report any ifspeed except on the loopback interface.  By comparison, the SG200 shows ifspeed on every interface.
    Does anyone here have any idea why I can't get an interface speed?  This is required for the MRTG traffic tracking program.  I don't think Cisco supports this product with phone support, but if they do, please, let me know.
    Cisco ISA550
    C:\usr\bin>snmpwalk -v2c -c Rpublic 192.168.1.1
    SNMPv2-MIB::sysDescr.0 = STRING: Linux, Cisco Small Business ISA550(ISA550-K9), Version 1.2.18 T
    hu Oct 31 12:56:40 CST 2013
    SNMPv2-MIB::sysObjectID.0 = OID: SNMPv2-SMI::enterprises.9.6.1.24.5.16.0.0
    DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (25477000) 2 days, 22:46:10.00
    SNMPv2-MIB::sysContact.0 = STRING: Tom Mountain
    SNMPv2-MIB::sysName.0 = STRING: RTISA550rtr
    SNMPv2-MIB::sysLocation.0 = STRING: Tampa, FL
    SNMPv2-MIB::sysORLastChange.0 = Timeticks: (0) 0:00:00.00
    SNMPv2-MIB::sysORID.1 = OID: SNMP-FRAMEWORK-MIB::snmpFrameworkMIBCompliance
    SNMPv2-MIB::sysORID.2 = OID: SNMP-MPD-MIB::snmpMPDCompliance
    SNMPv2-MIB::sysORID.3 = OID: SNMP-USER-BASED-SM-MIB::usmMIBCompliance
    SNMPv2-MIB::sysORID.4 = OID: SNMPv2-MIB::snmpMIB
    SNMPv2-MIB::sysORID.5 = OID: TCP-MIB::tcpMIB
    SNMPv2-MIB::sysORID.6 = OID: IP-MIB::ip
    SNMPv2-MIB::sysORID.7 = OID: UDP-MIB::udpMIB
    SNMPv2-MIB::sysORID.8 = OID: SNMP-VIEW-BASED-ACM-MIB::vacmBasicGroup
    SNMPv2-MIB::sysORDescr.1 = STRING: The SNMP Management Architecture MIB.
    SNMPv2-MIB::sysORDescr.2 = STRING: The MIB for Message Processing and Dispatching.
    SNMPv2-MIB::sysORDescr.3 = STRING: The management information definitions for the SNMP User-base
    d Security Model.
    SNMPv2-MIB::sysORDescr.4 = STRING: The MIB module for SNMPv2 entities
    SNMPv2-MIB::sysORDescr.5 = STRING: The MIB module for managing TCP implementations
    SNMPv2-MIB::sysORDescr.6 = STRING: The MIB module for managing IP and ICMP implementations
    SNMPv2-MIB::sysORDescr.7 = STRING: The MIB module for managing UDP implementations
    SNMPv2-MIB::sysORDescr.8 = STRING: View-based Access Control Model for SNMP.
    IF-MIB::ifSpeed.1 = Gauge32: 1000000000
    IF-MIB::ifSpeed.2 = Gauge32: 0
    IF-MIB::ifSpeed.3 = Gauge32: 0
    IF-MIB::ifSpeed.4 = Gauge32: 0
    IF-MIB::ifSpeed.5 = Gauge32: 0
    IF-MIB::ifSpeed.6 = Gauge32: 0
    IF-MIB::ifSpeed.7 = Gauge32: 0
    IF-MIB::ifSpeed.8 = Gauge32: 0
    IF-MIB::ifSpeed.9 = Gauge32: 0
    IF-MIB::ifSpeed.10 = Gauge32: 0
    IF-MIB::ifSpeed.11 = Gauge32: 0
    IF-MIB::ifSpeed.12 = Gauge32: 0
    IF-MIB::ifSpeed.13 = Gauge32: 0
    IF-MIB::ifSpeed.14 = Gauge32: 0
    IF-MIB::ifSpeed.15 = Gauge32: 0
    IF-MIB::ifSpeed.16 = Gauge32: 0
    IF-MIB::ifSpeed.17 = Gauge32: 0
    IF-MIB::ifSpeed.18 = Gauge32: 0
    IF-MIB::ifSpeed.19 = Gauge32: 0
    IF-MIB::ifSpeed.20 = Gauge32: 0
    IF-MIB::ifSpeed.21 = Gauge32: 0
    IF-MIB::ifSpeed.22 = Gauge32: 0
    IF-MIB::ifSpeed.23 = Gauge32: 0
    IF-MIB::ifSpeed.24 = Gauge32: 0
    IF-MIB::ifSpeed.25 = Gauge32: 0
    IF-MIB::ifSpeed.26 = Gauge32: 0
    IF-MIB::ifSpeed.27 = Gauge32: 0
    IF-MIB::ifSpeed.28 = Gauge32: 0
    IF-MIB::ifSpeed.29 = Gauge32: 0
    IF-MIB::ifSpeed.30 = Gauge32: 0
    IF-MIB::ifSpeed.31 = Gauge32: 0
    IF-MIB::ifSpeed.32 = Gauge32: 0
    IF-MIB::ifSpeed.33 = Gauge32: 0
    IF-MIB::ifSpeed.34 = Gauge32: 0
    IF-MIB::ifSpeed.35 = Gauge32: 0
    Cisco SG200 Switch
    C:\usr\bin>snmpwalk -v2c -c Rpublic 192.168.1.40
    SNMPv2-MIB::sysDescr.0 = STRING: 26-Port Gigabit Smart Switch
    SNMPv2-MIB::sysObjectID.0 = OID: SNMPv2-SMI::enterprises.9.6.1.88.26.1
    DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (114312300) 13 days, 5:32:03.00
    SNMPv2-MIB::sysContact.0 = STRING: Tom Mountain
    SNMPv2-MIB::sysName.0 = STRING: RTsg200SW
    SNMPv2-MIB::sysLocation.0 = STRING: Tampa, FL
    SNMPv2-MIB::sysServices.0 = INTEGER: 2
    SNMPv2-MIB::sysORLastChange.0 = Timeticks: (0) 0:00:00.00
    SNMPv2-MIB::sysORID.1 = OID: SNMPv2-SMI::enterprises.89.73
    SNMPv2-MIB::sysORDescr.1 = STRING: RS capabilities
    SNMPv2-MIB::sysORUpTime.1 = Timeticks: (0) 0:00:00.00
    IF-MIB::ifSpeed.49 = Gauge32: 100000000
    IF-MIB::ifSpeed.50 = Gauge32: 1000000000
    IF-MIB::ifSpeed.51 = Gauge32: 1000000000
    IF-MIB::ifSpeed.52 = Gauge32: 1000000000
    IF-MIB::ifSpeed.53 = Gauge32: 1000000000
    IF-MIB::ifSpeed.54 = Gauge32: 1000000000
    IF-MIB::ifSpeed.55 = Gauge32: 1000000000
    IF-MIB::ifSpeed.56 = Gauge32: 1000000000
    IF-MIB::ifSpeed.57 = Gauge32: 1000000000
    IF-MIB::ifSpeed.58 = Gauge32: 1000000000
    IF-MIB::ifSpeed.59 = Gauge32: 1000000000
    IF-MIB::ifSpeed.60 = Gauge32: 1000000000
    IF-MIB::ifSpeed.61 = Gauge32: 1000000000
    IF-MIB::ifSpeed.62 = Gauge32: 1000000000
    IF-MIB::ifSpeed.63 = Gauge32: 1000000000
    IF-MIB::ifSpeed.64 = Gauge32: 1000000000
    IF-MIB::ifSpeed.65 = Gauge32: 1000000000
    IF-MIB::ifSpeed.66 = Gauge32: 1000000000
    IF-MIB::ifSpeed.67 = Gauge32: 1000000000
    IF-MIB::ifSpeed.68 = Gauge32: 1000000000
    IF-MIB::ifSpeed.69 = Gauge32: 1000000000
    IF-MIB::ifSpeed.70 = Gauge32: 1000000000
    IF-MIB::ifSpeed.71 = Gauge32: 1000000000
    IF-MIB::ifSpeed.72 = Gauge32: 1000000000
    IF-MIB::ifSpeed.73 = Gauge32: 1000000000
    IF-MIB::ifSpeed.74 = Gauge32: 1000000000
    IF-MIB::ifSpeed.1000 = Gauge32: 0
    IF-MIB::ifSpeed.1001 = Gauge32: 0
    IF-MIB::ifSpeed.1002 = Gauge32: 0
    IF-MIB::ifSpeed.1003 = Gauge32: 0
    IF-MIB::ifSpeed.3000 = Gauge32: 0
    IF-MIB::ifSpeed.100000 = Gauge32: 0

  • ISA550 Wan Speeds VS direct to modem

    Today I noticed that if I connect my computer directly to the modem I am getting speeds of 67MBPS down and 3.5 Up. When I go through the ISA550 I am getting 47 down and 3.5 up. Is this fixable?

    Hello,
    Your speeds are most likely slower because of the security services running on your ISA.
    I took a quick look at the datasheet for the ISA550 and the throughput when the various threat management features are enabled is listed at 45Mbps, right around what you are getting.
    As a test go through and disable the security services one at a time to narrow down which one is slowing you down, my guess would be the A/V or IPS. 
    So it is fixable in a way, using just the firewall the device can handle up to 200Mpbs, but that does mean you would need to disable some security features.
    Hope that helps and thank you for choosing Cisco,
    Christopher Ebert - Advanced Network Support Engineer
    Cisco Small Business Support Center
    *please rate helpful posts*

Maybe you are looking for

  • To call db2 stored procedure having parameters in java application

    Hi, I've created db2 stored procedure which is running perfectly on db2 server after giving a CALL to it. But when I tried to call this same stored procedure in java application, its reflecting with following error...... com.ibm.db2.jcc.b.SqlExceptio

  • Gainer Focus and Lost Focus

    How implements the methods to gainer focus and lost focus? Thanks

  • RTGS AND NEFT Payment method  Through Automatic Programe

    Hi Experts, We are on the process of implementing automatic payments . Client requirement is , they wants to payment through RTGS/NEFT through automatic payment programme. Means when they run payemnt programe for the particular period through RTGS pa

  • IPhoto '09 Doesn't Name Folders after Events?

    I noticed that with iPhoto '09 the folders in Originals and Modified no longer correspond to the names of the events. This was a huge organizational feature of '07 and '08 and I wonder if this was intentionally removed (if so, why?) or if there's jus

  • X23 Bios and Embedded Controller Program Updating

    I am trying to update my bios on my x23.  I have relatively old versions of both the bios and the ECP, and both say that they won't work without more current version of the other.  Which one am I supposed to update first? thanks, David