ISCSI on all interfaces

Is it possible to disable iSCSI from talking on certain interfaces? I want a management interface with no iSCSI reachable on that NIC.

Hello lantech
Unfortunately there is not an option in the Lifeline firmware to disable iSCSI traffic on a specific NIC.
I recommend setting the 'Management interface' NIC to a different subnet and/or vlan that is designated for device management. This should prevent other local initiator clients to detect the management nic as a iscsi option.
Really iSCSI traffic should be segmented from all other network uses for best I/O performance with the LUNs.
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/

Similar Messages

NetFlow on All Interfaces

Hi All,
We are using ManageEngine NetFlow Analyzer to monitor our network traffic.
We have a few VLAN interfaces on the switch where we have enabled flow-export ingress and egress. We can see traffic that is passing between the VLANs on which flow-export has been configured. However, we have on interface that is connected to remote locations. We have not enabled flow-export on this interface. The idea was that, we have enabled ingress and egress flow-export, and the remote locations connect to VLANs where flow-export is already enabled, we must get all traffic from there. But we cannot see traffic from the remote locations, but we can see traffic from inside network to remote locations.
After checking ManageEngine documentation, I see that we have to enable netflow on all interfaces to get accurate report. Can anyone let me know why this is required. We already have ingress and egress flow-export, and we must be getting all traffic. Please suggest.
Thanks in advance,
Faiz

Hello Faiz,
As you probably know, NetFlow by default is only collected ingress. The ingress flows collected on all interfaces are used to display the outbound traffic on a selected interface. I don't know about ManageEngine but, in some NetFlow solutions, interfaces without NetFlow/IPFIX enabled will not be displayed regardless of whethor or not flows are going out of it.
Regarding ingress/egress being enabled on the same interface. If you are using flexible NetFlow to configure the export, make sure the "flow direction" is exported in the template. The commands to export both look like this:
ip flow monitor andrew-mon input
ip flow monitor andrew-mon output
Here is a good article on enabling ingress and egress NetFlow. Realize that just because you export both ingress and egress on a single interface and you export the direction, this doesn't mean the NetFlow solution will report on the data with a behavior that you would expect.
Ingress and egress flows are exported at the same time with only one difference "flow direction". For this reason, this element must be included in the template to ensure that utilization isn't overstated in the flow report. Again, this of course depends on your reporting solution.
Many vendors can't deal with a mixture of ingress and egress flows being enabled in a seemingly random fashion on the same device. In other words, they expect all ingress or all egress. Only a few vendors can handle a hybrid approach.
I hope this helps.
Jake

Why can't GB let me use 'electric guitar' option when using Nio 2/4 interface - I have to use real instrument and miss out on all the effects. Is this normal for all interfaces?

Why can't GB let me use 'electric guitar' option when using Nio 2/4 interface - I have to use real instrument and miss out on all the effects. Is this normal for all interfaces? The Nio reads hte guitar but GB doesn't....

Usually effects packages are AU plugins that would have no effect on track selection. Interfaces should have no control over what kind of track you can select. I really think something else is going on her maybe something you overlooked.
Did you choose the input channel in the track info pane. Try both channel 1 mono or channel 2 mono. Make sure the track is record enabled.

Set secondary DHCP on ALL interfaces.

I wanted to post this as it's own question although it is posted already under "Ask the experts".
We've added a secondary DHCP server to our network so that if one fails or is taken down for maintenance, we don't have a gap in service. I need to add this new DHCP address to each interface for each controller in WCS. I have 4 WLC's with 9 interfaces per. That's 36 slow UI copy and pastes I'm not looking forward too. Is there a quick way to propogate this secondary DNS to all interfaces?
I've looked at Controller Templates and Controller Config Groups but can't seem to find my way through either to a solution to my situation. Can you offer any advice?
(Unrelated) Also, I can't post to this group from Firefox. IE works fine. Weird.

I wanted to post this as it's own question although it is posted already under "Ask the experts".
We've added a secondary DHCP server to our network so that if one fails or is taken down for maintenance, we don't have a gap in service. I need to add this new DHCP address to each interface for each controller in WCS. I have 4 WLC's with 9 interfaces per. That's 36 slow UI copy and pastes I'm not looking forward too. Is there a quick way to propogate this secondary DNS to all interfaces?
I've looked at Controller Templates and Controller Config Groups but can't seem to find my way through either to a solution to my situation. Can you offer any advice?
(Unrelated) Also, I can't post to this group from Firefox. IE works fine. Weird.

Oracle db listening on all interfaces

Hi,
I have oracle xe installed on a server linux.
Customer did some changes on the nw and now the database does not listen on all interfaces but just on 127.0.0.1:1521.
I need Oracle listening on this port but on all available ips in this server, in other words 0.0.0.0:1521.
I can I achieve this? I am not a db expert.
I need to do this because I have many installed product, especially OID, and I do not know what IP is actually used to connect to the database.
Thanks much.

As1mov wrote:
This is ok, the problem is that OID does not create the LDAP listner even though it seams to connect correctly to the database. Missing something here from the problem description. A LDAP listener/server is not the same an Oracle listener. Uses different tcp ports and different application protocols. Also, you mentioned Oracle XE - last time I looked this was vanilla Oracle RDBMS. No OID included.
If you are talking about not being able to connect to an OID server - that requires oidmon and oidctl (console commands) to be used to start up the OID server (with its listener).
Should I take care of something if I add a new ip address to the linux box?Assuming that the Oracle Listener is not configured with +(IP=FIRST)+, then no - I would expect that bouncing the listener is all that is needed for the listener to start listening on port 1521 using the +0.0.0.0+. And this can be checked by using netstat or lsof commands (the latter can be used to list the tcp ports opened by the listener process).
If you have an error - please provide as much technical details as possible. Such as the listener.ora file, the alias entry used from tnsnames.ora, the output of a sqlplus session that attempted to use this alias to connect and failed, etc.
I'm not clear at all as to what the problem is that you're facing with the listener and multiple interfaces/IP addresses on the same server.

Query all interfaces

Hi,
Would really appreciate some assistance in what I 'thought' is a simple task
This is what I want to do via TCL / EEM :
1.) Enumerate all interfaces on the switch or just query the running config
2.) Query each interface config
3.) If the interface config doesn't contain the sting 'authentication port-control auto' - send an email with the resulting interface name etc
I'm starting to lose my mind trying to do this
Thanks and regards,
Bill

Try this:
event manager applet intf-auth
event none
action 001 cli command "enable"
action 002 cli command "show ip int brie"
action 003 set output "$_cli_result"
action 004 set intfs ""
action 005 foreach line "$output" "\n"
action 006   string trim $line
action 007   set line $_string_result
action 008   string length $line
action 009   if $_string_result eq 0
action 010    continue
action 011   end
action 012   regexp "^Interface" "$line"
action 013   if $_regexp_result eq "1"
action 014    continue
action 015   end
action 016   regexp "#" "$line"
action 017   if $_regexp_result eq "1"
action 018    continue
action 019   end
action 020   regexp "^([^[:space:]]+)" "$line" match intf
action 021   cli command "show run interface $intf"
action 022   regexp "authentication port-control auto" "$_cli_result"
action 023   if $_regexp_result eq "0"
action 024    append intfs " $intf"
action 025   end
action 026 end
action 027 string length "$intfs"
action 028 if $_string_result gt "0"
action 029   mail from "[email protected]" to "[email protected]" server "10.1.1.1" subject "Interfaces missing auth port-control" body "The following interfaces are missing 'auth port-control auto': $intfs"
action 030 end

Windows Server 2012 - Hyper-V - iSCSI SAN - All Hyper-V Guests stops responding and extensive disk read/write

We have a problem with one of our deployments of Windows Server 2012 Hyper-V with a 2 node cluster connected to a iSCSI SAN.
Our setup:
Hosts - Both run Windows Server 2012 Standard and are clustered.
HP ProLiant G7, 24 GB RAM, 2 teamed NIC dedicated to Virtual Machines and Management, 2 teamed NIC dedicated to iSCSI storage. - This is the primary host and normaly all VMs run on this host.
HP ProLiant G5, 20 GB RAM, 1 NIC dedicated to Virtual Machines and Management, 2 teamed NIC dedicated to iSCSI storage. - This is the secondary host that and is intended to be used in case of failure of the primary host.
We have no antivirus on the hosts and the scheduled ShadowCopy (previous version of files) is switched of.
iSCSI SAN:
QNAP NAS TS-869 Pro, 8 INTEL SSDSA2CW160G3 160 GB i a RAID 5 with a Host Spare. 2 Teamed NIC.
Switch:
DLINK DGS-1210-16 - Both the network cards of the Hosts that are dedicated to the Storage and the Storage itself are connected to the same switch and nothing else is connected to this switch.
Virtual Machines:
3 Windows Server 2012 Standard - 1 DC, 1 FileServer, 1 Application Server.
1 Windows Server 2008 Standard Exchange Server.
All VMs are using dynamic disks (as recommended by Microsoft).
Updates
We have applied the most resent updates to the Hosts, WMs and iSCSI SAN about 3 weeks ago with no change in our problem and we continually update the setup.
Normal operation
Normally this setup works just fine and we see no real difference in speed in startup, file copy and processing speed in LoB applications of this setup compared to a single host with 2 10000 RPM Disks. Normal network speed is 10-200 Mbit, but occasionally
we see speeds up to 400 Mbit/s of combined read/write for instance during file repair
Our Problem
Our problem is that for some reason all of the VMs stops responding or responds very slowly and you can for instance not send CTRL-ALT-DEL to a VM in the Hyper-V console, or for instance start task manager when already logged in.
Symptoms (i.e. this happens, or does not happen, at the same time)
I we look at resource monitor on the host then we see that there is often an extensive read from a VHDX of one of the VMs (40-60 Mbyte/s) and a combined write speed to many files in \HarddiskVolume5\System Volume Information\{<someguid and no file extension>}.
See iamge below.
The combined network speed to the iSCSI SAN is about 500-600 Mbit/s.
When this happens it is usually during and after a VSS ShadowCopy backup, but has also happens during hours where no backup should be running (i.e. during daytime when the backup has finished hours ago according to the log files). There is however
not that extensive writes to the backup file that is created on an external hard drive and this does not seem to happen during all backups (we have manually checked a few times, but it is hard to say since this error does not seem leave any traces in event
viewer).
We cannot find any indication that the VMs themself detect any problem and we see no increase of errors (for example storage related errors) in the eventlog inside the VMs.
The QNAP uses about 50% processing Power on all cores.
We see no dropped packets on the switch.
(I have split the image to save horizontal space).
Unable to recreate the problem / find definitive trigger
We have not succeeded in recreating the problem manually by, for instance, running chkdsk or defrag in VM and Hosts, copy and remove large files to VMs, running CPU and Disk intensive operations inside a VM (for instance scan and repair a database file).
Questions
Why does all VMs stop responding and why is there such intensive Read/Writes to the iSCSI SAN?
Could it be anything in our setup that cannot handle all the read/write requests? For instance the iSCSI SAN, the hosts, etc?
What can we do about this? Should we use MultiPath IO instead of NIC teaming to the SAN, limit bandwith to the SAN, etc?

Hi,
> All VMs are using dynamic disks (as recommended by Microsoft).
If this is a testing environment, it’s okay, but if this a production environment, it’s not recommended. Fixed VHDs are recommended for production instead of dynamically expanding or differencing VHDs.
Hyper-V: Dynamic virtual hard disks are not recommended for virtual machines that run server workloads in a production environment
http://technet.microsoft.com/en-us/library/ee941151(v=WS.10).aspx
> This is the primary host and normaly all VMs run on this host.
According to your posting, we know that you have Cluster Shared Volumes in the Hyper-V cluster, but why not distribute your VMs into two Hyper-V hosts.
Use Cluster Shared Volumes in a Windows Server 2012 Failover Cluster
http://technet.microsoft.com/en-us/library/jj612868.aspx
> 2 teamed NIC dedicated to iSCSI storage.
Use Microsoft MultiPath IO (MPIO) to manage multiple paths to iSCSI storage. Microsoft does not support teaming on network adapters that are used to connect to iSCSI-based storage devices. (At least it’s not supported until Windows Server 2008 R2. Although
Windows Server 2012 has built-in network teaming feature, I don’t article which declare that Windows Server 2012 network teaming support iSCSI connection)
Understanding Requirements for Failover Clusters
http://technet.microsoft.com/en-us/library/cc771404.aspx
> I have seen using MPIO suggests using different subnets, is this a requirement for using MPIO
> or is this just a way to make sure that you do not run out of IP adressess?
What I found is: if it is possible, isolate the iSCSI and data networks that reside on the same switch infrastructure through the use of VLANs and separate subnets. Redundant network paths from the server to the storage system via MPIO will maximize availability
and performance. Of course you can set these two NICs in separate subnets, but I don’t think it is necessary.
> Why should it be better to not have dedicated wireing for iSCSI and Management?
It is recommended that the iSCSI SAN network be separated (logically or physically) from the data network workloads. This ‘best practice’ network configuration optimizes performance and reliability.
Check that and modify cluster configuration, monitor it and give us feedback for further troubleshooting.
For more information please refer to following MS articles:
Volume Shadow Copy Service
http://technet.microsoft.com/en-us/library/ee923636(WS.10).aspx
Support for Multipath I/O (MPIO)
http://technet.microsoft.com/en-us/library/cc770294.aspx
Deployments and Tests in an iSCSI SAN
http://technet.microsoft.com/en-US/library/bb649502(v=SQL.90).aspx
Hope this helps!
TechNet Subscriber Support
If you are
TechNet Subscription user and have any feedback on our support quality, please send your feedback
here.
Lawrence
TechNet Community Support

List of all interfaces in the XI landscape

Hi Experts,
Currently my company is going through a merge project with a second company, and we want to integrate the SAP systems. This will inevitably mean more interfaces to be built. What we would like to have is a way to generate a list of all the current interfaces in the XI landscape, so we can get a good overview of what can be reused or copied.
I know we can get a list by opening the ID and looking at the configured scenario's, but we would like to automate this. Are there any tables where the interface scenario names are stored, and where we can see which type of interface it is (IDOC / File / JDBC / ...)?
If someone knows of a solution for this, it would be greatly appreciated. Otherwise this will remain a manual action, and as such, prone to mistakes or oversights...
Our current XI landscape is XI 3.0, SP18.
Thanks in advance,
Yordy

Hi,
Solution is very simple: Use ABAP table SMPPREL3, this table contains all relationships (end-2-end) interface. You can use this table to know all about interface.
Only caution is that this table also have some wild-card entries so total number of interface count can vary by 1-2%, but this happen on runtime only, this table will perfectly match your manual counting.
Regards,
Gourav
<i>Reward points if it helps you</i>

Migrating a work repository loses the LKM selection on all interfaces

Hi,
I have a number of projects that I have just moved from one development environment to another. I've actually carried it out twice now and had the same error each time.
I export the work repository from my working development environment, then after setting up all the connections/schemas in the new environment, I import the work repository through designer.
Everything seems to import fine, all my models are there, all my projects are there, but
1. The models no longer have the Journalising Knowledge module selected and I have to reselect it before starting any journals.
2. All the interfaces have lost the selection of the LKM in the flow tab. I have to open each interface and select the LKM I want and then rebuild all my scenarios.
Has anyone seen this problem? Any light you can shed?
I had a search and haven't seen anything similar.
Regards
Damian

Has anyone else had this problem? Any reason why the LKM selection gets dropped during the import?
It is quite a hassle to fix up every interface & then regenerate scenario's after importing a repository.
Cheers,
Matt

Hi all,Interface vs Abstract class

Hi, All When We are going to use interface or an Abstract class,Can tell exactly
Thanks in advance

Interface class is used to contain methods that is to be defined by children classes. And abstract class, even though you can have all methods being abstract, but normally I would use this class for situation such as implement methods that are general enough to be used by the children classes and left others being abstract to be implemented by children classes later. I always think this relationship in a simple way:
Abstract Class: Animal
Interface : Leg, Tail, Hair, Feather, Head...
Children classes: Tiger, Bird, etc.
Thus, for class Animal class you can have methods such as:
Abstract: canRoar, canSing, canFly, ...
Non-abstract: isSleeping, isAlive...
More example:
Tiger extends Animal implements Leg, Tail, Head, Hair
Bird extends Animal implements Leg, Feather, Head
I could be wrong, correct me if so. Cheers.

I need to increase the sizes of all interfaces due to disability, how do I do it?

I've spent ages looking but haven't found an option to increase all the user interface text sizes, icons etc.

Apart from mooblie's suggestion, another approach is to go to System Preferences, click on Accessibility, and then enable and configure the zoom options.
In some cases you cannot simply reduce the resolution as per mooblie's suggestion as some applications will onlu run with a minimum size resolution for example Apple's Workgroup Manager tool for use with their server will not run at lower resolutions. The zoom option does not suffer this problem.

Re: All interfaces should now be configured in /etc/conf.d/netcfg

With all due respect, I feel that this announcement should be accompanied by some addition documentation or at least a link to a relevant the wiki article. I don't even have core/netcfg installed on my systems.
Last edited by graysky (2012-08-12 03:41:16)

stryder wrote:I read the title and text and still could not be sure, because I was not sure whether netcfg is the basic program used by arch to handle interfaces. The text should say "Those using netcfg should configure interfaces in /etc/conf.d/netcfg rather than /etc/rc.conf." .....
That would be quite easy to understand and impossible to misunderstand. Those writing announcements should write them like that.
"Those using netcfg should..."
Yes the announcment bothered me very much. My overly educated mind trained in scholarly English said to me "What the HELL is netcfg and WHY do I now have to use it!"

Ipfilter on not all interfaces

Hi,
i want to run ipfilter (from solaris 10) on only a few of my interfaces.
I tried a line like
bge 1 0 pfil
in /etc/ipf/pfil.ap. (On my box minor 1 seems to be bge0).
pfil is running, but ipfilter does not start due to:
pfil not plumbed on any network interfaces.
in /var/svc/log/network-ipfilter:default.log
The manual page for autopush suggests my config is ok.
Has anybody ever tried this? Does it work? How?
thanks, tom.

I found a workaround, but a poor one:
unplumb the device (ifconfig <device_name> unplumb)
autopush /etc/ipf/pfil.ap (assuming it's configured correctly, with the device name uncommented from the list)
re-plumb the device (ifconfig <device_name> plumb xxx.xxx.xx.xxx netmask 255.255.255.0 up)
enable the services:
svcadm enable pfil
svcadm enable ipfilter

Lagging experience at all interface animations in OS X Mavericks

Hi,
I am having the same problem described in the topic https://discussions.apple.com/thread/5479303?tstart=0
So I have completed the steps suggested to reset the SMC and later made a ETRE check. I have pasted the check report in here. Please suggest ways to get rid of this problem.
Hardware Information:
          MacBook Pro (13-inch, Mid 2012)
          MacBook Pro - model: MacBookPro9,2
          1 2.9 GHz Intel Core i7 CPU: 2 cores
          8 GB RAM
Video Information:
          Intel HD Graphics 4000 - VRAM: 1024 MB
System Software:
          OS X 10.9.1 (13B42) - Uptime: 0 days 0:3:25
Disk Information:
          TOSHIBA MK7559GSXF disk0 : (750.16 GB)
                    EFI (disk0s1) <not mounted>: 209.7 MB
                    disk0s2 (disk0s2) <not mounted>: 668.3 GB
                    Recovery HD (disk0s3) <not mounted>: 650 MB
                    BOOTCAMP (disk0s4) /Volumes/BOOTCAMP: 81 GB (36.29 GB free)
          MATSHITADVD-R   UJ-8A8
USB Information:
          Apple Inc. FaceTime HD Camera (Built-in)
          Apple Inc. BRCM20702 Hub
                    Apple Inc. Bluetooth USB Host Controller
          Apple Inc. Apple Internal Keyboard / Trackpad
          Apple Computer, Inc. IR Receiver
FireWire Information:
Thunderbolt Information:
          Apple Inc. thunderbolt_bus
Kernel Extensions:
          com.Cycling74.driver.Soundflower          (1.6.6 - SDK 10.6)
          com.tuxera.filesystems.tufsfs.fusefs_txantfs          (2011.4.23)
Problem System Launch Daemons:
Problem System Launch Agents:
Launch Daemons:
          [System] com.adobe.fpsaud.plist 3rd-Party support link
          [System] com.adobe.SwitchBoard.plist 3rd-Party support link
          [System] com.cleverfiles.cfbackd.plist 3rd-Party support link
          [System] com.google.keystone.daemon.plist 3rd-Party support link
          [System] com.macpaw.CleanMyMac2.Agent.plist 3rd-Party support link
          [System] com.microsoft.office.licensing.helper.plist 3rd-Party support link
          [System] com.oracle.java.Helper-Tool.plist 3rd-Party support link
          [System] com.robohippo.HippoConnectDaemon.plist 3rd-Party support link
          [System] com.teamviewer.teamviewer_service.plist 3rd-Party support link
          [System] com.tunnelbear.mac.tbeard.plist 3rd-Party support link
          [System] com.wdc.SmartwareDriveService.plist 3rd-Party support link
          [System] com.wdc.WDSmartWareService.plist 3rd-Party support link
Launch Agents:
          [System] com.adobe.AAM.Updater-1.0.plist 3rd-Party support link
          [System] com.adobe.CS5ServiceManager.plist 3rd-Party support link
          [System] com.google.keystone.agent.plist 3rd-Party support link
          [System] com.oracle.java.Java-Updater.plist 3rd-Party support link
          [System] com.robohippo.HippoConnectAgent.plist 3rd-Party support link
          [System] com.teamviewer.teamviewer.plist 3rd-Party support link
          [System] com.teamviewer.teamviewer_desktop.plist 3rd-Party support link
User Launch Agents:
          [not loaded] com.macpaw.CleanMyMac2Helper.scheduledScan.plist 3rd-Party support link
          [not loaded] com.macpaw.CleanMyMac2Helper.trashWatcher.plist 3rd-Party support link
          [not loaded] com.spotify.webhelper.plist 3rd-Party support link
User Login Items:
          iTunesHelper
          SmartDaemon
          Dropbox
          Caffeine
          Alfred 2
          Google Chrome
          Box Sync
          WDDriveUtilityHelper
          WDQuickView
Internet Plug-ins:
          o1dbrowserplugin: Version: 4.9.1.16010 3rd-Party support link
          Default Browser: Version: 537 - SDK 10.9
          AdobePDFViewerNPAPI: Version: 10.1.4 3rd-Party support link
          FlashPlayer-10.6: Version: 12.0.0.38 - SDK 10.6 3rd-Party support link
          Silverlight: Version: 5.1.20913.0 - SDK 10.6 3rd-Party support link
          Flash Player: Version: 12.0.0.38 - SDK 10.6 3rd-Party support link
          QuickTime Plugin: Version: 7.7.3
          googletalkbrowserplugin: Version: 4.9.1.16010 3rd-Party support link
          npgtpo3dautoplugin: Version: 0.1.44.29 - SDK 10.5 3rd-Party support link
          AdobePDFViewer: Version: 10.1.4 3rd-Party support link
          SharePointBrowserPlugin: Version: 14.0.0 3rd-Party support link
          JavaAppletPlugin: Version: Java 7 Update 51 3rd-Party support link
Audio Plug-ins:
          BluetoothAudioPlugIn: Version: 1.0 - SDK 10.9
          AirPlay: Version: 1.9 - SDK 10.9
          AppleAVBAudio: Version: 2.0.0 - SDK 10.9
          iSightAudio: Version: 7.7.3 - SDK 10.9
User Internet Plug-ins:
          FolxNetscapePlugIn: Version: 2.0 - SDK 10.4 3rd-Party support link
3rd Party Preference Panes:
          Flash Player 3rd-Party support link
          Java 3rd-Party support link
          Tuxera NTFS 3rd-Party support link
          WDQuickView 3rd-Party support link
Bad Fonts:
          None
Old Applications:
          SmartDaemon:          Version: 1.0 - SDK 10.5 3rd-Party support link
                    /Library/Application Support/CleverFiles/SmartDaemon.app
          CORE Keygen:          Version: 1.0 - SDK 10.5
                    /Users/[redacted]/Downloads/MacHider with CORE keygen v. 1.6.5/CORE Keygen.app
          Spin Doctor:          Version: 1.0 - SDK 10.5 3rd-Party support link
                    /Applications/Toast 11 Titanium/Spin Doctor.app
          SLLauncher:          Version: 1.0 - SDK 10.5 3rd-Party support link
                    /Library/Application Support/Microsoft/Silverlight/OutOfBrowser/SLLauncher.app
          Disk Drill:          Version: 1.7 - SDK 10.5 3rd-Party support link
          Folx:          Version: 2.0 - SDK 10.4 3rd-Party support link
          oDesk Team:          Version: 3.4.51 - SDK 10.5 3rd-Party support link
          SmartwareServiceApp:          Version: 1.16 - SDK 10.5 3rd-Party support link
                    /Library/Application Support/WD SmartWare Services/SmartwareServiceApp.app
Time Machine:
          Mobile backups: ON
          Auto backup: YES
          Volumes being backed up:
          Destinations:
                    Time Capsule [Local] (Last used)
                    Total size: 3
                    Total number of backups: 1
                    Oldest backup: 2014-02-02 18:07:41 +0000
                    Last backup: 2014-02-02 18:07:41 +0000
                    Size of backup disk: Excellent
                              Backup size 3 > (Disk size 0 B X 3)
          Time Machine details may not be accurate.
          All volumes being backed up may not be listed.
Top Processes by CPU:
               2%          WindowServer
               1%          EtreCheck
               1%          mds_stores
               1%          Box Sync
               1%          Google Chrome
Top Processes by Memory:
          172 MB          Skype
          164 MB          Google Chrome
          156 MB          com.apple.IconServicesAgent
          106 MB          Messages
          98 MB          Dropbox
Virtual Memory Information:
          3.29 GB          Free RAM
          3.38 GB          Active RAM
          501 MB          Inactive RAM
          867 MB          Wired RAM
          370 MB          Page-ins
          0 B          Page-outs

The last step during the installation process is to erase the installer...unfortunately. As soon as OS X has finished downloading it wants to install itself. Veterans usually quit the installer and copy it to another hard drive, a flash drive or copy it to the downloads folder before installing so they'll have a copy for emergencies.
I don't know that CleanMyMac does any damage - I tested it for my user group (on a cloned drive) and found nothing horrible about it. Just didn't see anything particularly good about it either.
Given that your computer is using a relatively slow hard drive and has only 4GB what you are seeing is pretty typical. Mavericks is happiest with a very fast hard drive and/or more RAM. My 2011 MBA is very happy with Mavericks with only 4GB but it has an SSD. When I clone to an external drive and test that drive the MBA is an entirely different (and slower) creature.
You are using two huge (and bloated) programs: MS Office and Adobe. Either one will cause your computer to use virtual memory. Add Safari or Google Chrome to the mix and you have a recipe for a case of the s-l-o-w-s. A memory upgrade is in your future.

Create NIC team using all interfaces

I'm trying to put together a function that will take all the physical NICs on a server and team them together. I'm not even sure where I found the example, but here is the code I have below. This seems like it should be much simpler and that I'm missing
something.
# Create a network team using switch independent teaming and Hyper-V port mode
Function TeamSetup ($teamName)
$adapters = Get-NetAdapter
$nicList = @()
Foreach ($nic in $adapters)
$nicList += $nic.Name
New-NetLbfoTeam $teamName –TeamMembers ($nicList) –TeamNicName $teamName -TeamingMode SwitchIndependent -LoadBalancingAlgorithm HyperVPort

This actually seems to be some sort of problem with running these commands as part of a script. If I enter my original code directly into PowerShell line-by-line, it works as expected. As does the same command using the * wildcard instead of the $nicList
variable. No matter how I change the code in the script, it fails with this error:
New-NetLbfoTeam : There are no teamable NetAdapters on the system matching TeamMembers parameter
At C:\Script.ps1:190 char:2
+ New-NetLbfoTeam $teamName â€“TeamMembers ($nicList) â€“TeamNicName $teamName -T ...
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ CategoryInfo : InvalidArgument: (MSFT_NetLbfoTeam:root/StandardCimv2/MSFT_NetLbfoTeam) [New-NetLbfoTeam
], CimException
+ FullyQualifiedErrorId : MiClientApiError_InvalidParameter,New-NetLbfoTeam

ISCSI on all interfaces

Similar Messages

Maybe you are looking for