ISCSI target setup fails: command "iscsitadm" not available?

Hello,
I want to set up a iSCSI target:
however it seems I don't have
iscsitadm
available on my system, only
iscsiadm
What to do?
Is this
http://alessiodini.wordpress.com/2010/10/24/iscsi-nice-to-meet-you/
still valid in terms of set up procedure?
Thanks

Ok,
here you go using COMSTAR:
pkg install storage-server
pkg install -v SUNWiscsit
http://thegreyblog.blogspot.com/2010/02/setting-up-solaris-comstar-and.html
svcs \*stmf\*
svcadm enable svc:/system/stmf:default
zfs create -V 250G tank-esata/macbook0-tm
sbdadm create-lu /dev/zvol/rdsk/tank-esata/macbook0-tm
sbdadm list-lu
stmfadm list-lu -v
stmfadm add-view 600144f00800271b51c04b7a6dc70001
svcs \*scsi\*
itadm create-target
devfsadm -i iscsi
reboot
Solaris 11 Express iSCSI manual:
http://dlc.sun.com/pdf/821-1459/821-1459.pdf
and that for reference
http://nwsmith.blogspot.com/2009/07/opensolaris-2009-06-and-comstar-iscsi.html
Windows iSCSI initiator
http://www.microsoft.com/downloads/en/details.aspx?familyid=12cb3c1a-15d6-4585-b385-befd1319f825&displaylang=en
works after manually adding the Server's IP (no auto detect)

Similar Messages

"This command is not available because no document is open" when opening Word 2013

Whenever I launch Word 2013, the error message "This command is not available because no document is open" appears. This causes an issue that prevents a program called SNAP used for education from working properly. I've been able
to work around the error message itself by disabling the start screen for Word 2013, so it opens straight into a blank document, but SNAP still does not work.
I've not been able to make any headway researching the issue. It seems most people run into this error scripting or coding, and it's usually that they try to save a document or something before they actually make the document.
I don't know that it's relevant, but this is occuring on a 32-bit Windows 7 box.

Hi, I work with SNAP Technical Support and this is a known issue with Cengage's KPDO add-in.
Cengage Keyboarding's Add-In to Word prevents the SnapPlayer application from communicating with Word. This add-in will
need to be disabled.
You
may see the following error in the log when this occurs:<Exception>System.Runtime.InteropServices.COMException
(0x80080005): Retrieving the COM class factory for component with CLSID {000209FF-0000-0000-C000-000000000046} failed due to the following error: 80080005.at
SnapPlayer.Skills.Applications.Word.Launch() in D:ProjectsVisual StudioSnap PlayerSnapSkillsApplicationsWord.vb:line 234
Disabling the add-in will resolve the issue.

Problem in converting word to html- file get error msg 'This command is not available because no document is open'

Hi,
I write the some asp code to save the word file from client machine to server machine , and convert it into the html file.
it working fine when i debug the code into the visual studio but when i deploy code on iis it give me a error 'This command is not available because no document is open' , while i try to save file into html format.
lot of time i try this give all the security full access to iis user and other things .
can any one help me. i fully frustrated from this problem.
my need only upload the word document from client to server machine and convert it into the word document.
only IIS give me the problem, suggest me what setting i need to do in iis
please help me humble request

Hi,
In this forum we mainly discuss questions about Office client questions and feedbacks, issues related to coding are not supported here.
Based on the description, although the question is about converting Word documents, it's more likely to be a permission issue, the question is better to be posted in the IIS.NET forum:
http://forums.iis.net/
The reason why we recommend posting appropriately is you will get the most qualified pool of respondents, and other partners who read the forums regularly can either share their knowledge or learn from your interaction with us. Thank you for your understanding.
Regards,
Melon Chen
TechNet Community Support
It's recommended to download and install
Configuration Analyzer Tool (OffCAT), which is developed by Microsoft Support teams. Once the tool is installed, you can run it at any time to scan for hundreds of known issues in Office
programs. Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact
[email protected]

Could not complete Photomerge command because COMMAND was not available. What do I do now?

Text of message when I tried a Photomerge: "Could not complete Photomerge command because "command" was not available."
How do I fix this?

Lots more information needed. Operating system and version, version of PSE, what exactly did you do to create your merge, step by step.

Message send failed: SSL implementation not available

Objective: to Jdev version 10.1.3 generate a client proxy for a given URL / wsdl and deploy to Oracle 10q
for use in PL \ SQL package. The problem it is necessary to establish an SSL connection.
After generating the client created AgentConnectClient class
/ / SSL
System.setProperty("ssl.SocketFactory.provider","oracle.security.ssl.OracleSSLSocketFactoryImpl");
System.setProperty("ssl.ServerSocketFactory.provider","oracle.security.ssl.OracleSSLServerSocketFactoryImpl");
System.setProperty("java.protocol.handler.pkgs","HTTPClient");
System.setProperty ("oracle.wallet.location", "/ etc / ORACLE / WALLETS / oracle");
System.setProperty ("oracle.wallet.password", "passw");
/ / Client
c = new AgentConnectClient ();
/ / end_point = "https:// ....";
c.setEndpoint (end_point);
CityListRequest requst = new CityListRequest ();
CityListResponse response = new CityListResponse ();
requst.setTimeStamp (Calendar.getInstance ());
requst.setApiVersion (apiVersion);
requst.setMaxRowsToReturn (new BigInteger (maxRowsToReturn.toString ()));
/ / request - response
response = c.cityList (requst);
Here there is a bug
; Nested exception is:
HTTP transport error: javax.xml.soap.SOAPException: java.security.PrivilegedActionException: javax.xml.soap.SOAPException: Message send failed: SSL implementation not available
Can anyone help, any ideas welcome - thank you.
Edited by: tyoma on Oct 6, 2011 6:52 PM

I also have that error for days and still no answer from java people here. I don't think they don't know really what they are talking about even people from sun don't know how to solve this problem.

Why netflow commands are not available in 4506-E?

Hi,
we have one 4506-E Chassis , Sup7L-E , LAN Base with cat4500e-universalk.SPA.03.03.00.SG.151-1.SG.bin image
why netflow commands are not available not available in this. someone said netflow will work only with IP base License , is that right?
Or how to enable it
thanks
Sujish

Hi,
For Nwtflow, you need IP Base or Enterprise Services License.
See table-1 in this link;
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/release/note/OL_26675-01.pdf
HTH

Get state of an iSCSI target using iscsicsli command

Hello !!
I want to display the state of an iSCSI target (connected, inactive, ...) using iscsicli command.
iscsicli ListTargets displays only the name of the different targets without the state. How can i do this please ?
Thanks !!

Hi,
iscsicli /? help show all available parameters. Currently I cannot help test but 2 possible parameters are:
iscsicli targetinfo
iscsicli listpersistenttargets
If neither could help then you may try powershell commands instead as Tim mentioned. However it is only supported in Windows Powershell 4.0.
If you have any feedback on our support, please send to [email protected]

Actions command make not available

I have been working with PSE since version 2 but have not posted in this forum so if I break a "rule", I apologize in advance.
Using PSE 13 ( new to this version) on a pc - Win 7 - hp laptop - plenty of hd space and memory
I have downloaded actions from a very reputable site and cannot get them to run. The error message: The command "make" is currently not available.
I've downloaded and unzipped fresh copies 3x. Deleted and reloaded to PSE 13 3x. So I thought the problem was in the actions until I ran through some of the default actions that came within PSE 13. Borders and Lose Weight seemed to work but when I came to Sepia Toning, I got the same error message. The message gives me the option to "continue" or "stop" but the action doesn't run correctly if I chose "continue".
Thanks in advance for your help.
Roberta

It might also be that the psds since from lightroom are 16 bits per channel.
After you transfer the psd from lightroom to photoshop elements, if you go to Image>Mode and click on 8 Bits/Channel, do the actions work?

GuiXT- Command 'column' not available

hi Gurus,
1] I am getting a error in GuiXt command 'column'
    The command line in BOM CS02 transcation is,
    Column "AvStock" size=8 name="AvStock" position=5
    Earlier same command line was working and i was getting a column named
    AvStock in CS02, without any changes now after some days system says
    that command 'column' is not available. This applies to all different systems
    (PC's) GUI for same server.
2] What are all settings should be done to get the effect of changes through GuiXt
    at Server level. Like putting a system name in guixt.ini file in server system.
Thanks in advance,
Abhi.

The Syntax used was wrong.

Time capsule backups failing - backup disk not available

All of a sudden I’m getting:
Time Machine could not complete the backup.
The backup disk is not available.
Time machine buddy’s log gives me:
Starting standard backup
Attempting to mount network destination using URL: afp://*.local/Data
NetAuthConnectToServerSync failed with error: 89 for url: afp://*.local/Data
Backup failed with error: 19
I’m connected to the Time Capsule right now (it’s how I connect to the web). I can see it in the shared list in Finder, although connection fails when trying to access it from Finder. What can I do?

Solution - I had the same thing happen to me with a Backup failed with error: 19 and what I did was this.
Stop any time machine backup in Time Machine preferences.
Go into Keychain Access in Utilities.
Go to search field and type "Local"
Delete any files that are of the kind "Time Machine Password". They should end in something like afpovertcp._tcp.local
Now turn on Time Machine back up in Preferences.
Click Select Disk and choose the volume.
You will be requested to enter the password and then it will take some time to establish the link and mount the backup volume. From there it will do a full back up.
Hope it works for you as well as it did for me.
Message was edited by: gfilev

Printer Setup Utility "Utility" tool not available

I have a Canon Pixma ip4200. I am trying to clean the print heads, which is done through the "Utility" option in the title bar of the Print Setup Utility. However, that option is dimmed (or greyed) and not accessible. I have re-installed the driver, and re-installed the printer, but it is still not available. Any help?

Read 2nd paragraph:
http://docs.info.apple.com/article.html?artnum=107418

Save command currently not available

Hi
I have created a Photoshop plugin and it was working fine..Now suddenly I am facing an issue..On execution, I am getting an error "Save Command is currently not available". I have not changed anything in code. I am not able to trace the reason.
Earlier I thought that it is space issue and I vacated memory in my system. But no luck.
Please guide.
Thanks

Something has changed in my functions for doing batch actions in Bridge. In CS5 Bridge I try to do a simple batch action of saving a DNG file as a jpg and closing the file. When I attempt this I get a message saying 'The command "Save" is currently not available.
Batch using tools menu from Bridge to reach Photoshop should work as expected in both CS4 and CS5. If not then there is something wrong on either your system or install.
Go to Bridge CS5 preference and look for the section Start Up Scripts and see if there is still a Start Up Script for Photoshop CS5 present and with a checkmark in front for activation. If not try first to restart bridge holding down option key and choose refresh preferences. This should retrieve the original Start Up scripts again.
If your command save as is not available check the action and see what the save path for that acton is. If it is a copied action from an other system changes are that it still contains the save path for the old drive and if the script can't find it it provides a warning message.
Also check if the drive you save to has both read and write permission.

Darwin.cli : Most of the cli commands are not available

Most of the command lines in 6.1 does not work in vcloud application director 6.1 for example
list-cloud-tunnels' was found but is not currently available (type 'help' then ENTER to learn about this command)
spring> create-cloud-tunnel
Command 'create-cloud-tunnel' was found but is not currently available (type 'help' then ENTER to learn about this command)
spring> cliversion
vCloud Automation Center Application Services CLI BUILD 6.1.0-2064245
Copyright (c) 2011-2014 VMwareInc. All rights reserved. This product is protected by U.S.
and international copyright and intellectual property laws.
VMware products are covered by one or more patents listed at http://www.vmware.com/go/patents
spring> display-user
Command 'display-user' was found but is not currently available (type 'help' then ENTER to learn about this command)
spring> list-cloud-tunnels
Command 'list-cloud-tunnels' was found but is not currently available (type 'help' then ENTER to learn about this command)
spring>

Thanks for your reply, i used the below command but not enough luck
login --serverUrl https://************:8443/darwin --username admin --password ********** --tenantId gis
According to the documentation here vCloud Application Director 6.0 Documentation Center admin has ROLE_SYSTEM_ADMIN,ROLE_CLOUD_ADMIN,ROLE_CATALOG_ADMIN,ROLE_APP_ARCHITECT,ROLE_DEPLOYER,ROLE_SYSTEM_INTEGRATOR permissions hence i was logging in as admin.
Thanks
Nataraj

Office 2013 : Ribbon some commands are not available

hi,
Sometimes, in excel or others applications, we have some issues regarding ribbon : commands are not functional !
We must close office applications to get back to a normal state.
We did a migration from Office 2007 to Office 2013.
best regards

Hi,
First, please make sure your Office program is fully patched.
If you installed any third-part program that is integrated to Microsoft Office, please temporarily disable the integration to check the result. Also try to disable all add-ins in Office programs to check the result.
In addition, please try to run a repair of your Office installation and then test the issue again:
http://office.microsoft.com/en-in/project-help/repair-office-programs-HA010357402.aspx
Hope this helps.
Best Regards,
Steve Fan
TechNet Community Support

Yomsemite reinstall failed, internal hdd not available to install to

Was attempting a reinstall of Yosemite due to recurring errors with Finder, TimeMachine and launch assistant after my main board was replaced. Rebooted with Cmd-C and chose to reinstall. Everything looked normal until it was around half-way finished. Then the screen went to dark grey and stayed like that for around an hour before it shut down. On reboot I get the grey screen with the "no" symbol (slashed circle). I tried rebooting from my clone drive (made with CCC every week - has worked many times before). It fails to boot past the half-way point. Finally, tried using a USB Yosemite installer, but it doesn't show the internal drive as being available to install to.
Any help would be appreciated.

Although I was unable to boot with Cmd-C it turns out I was able to boot to the recovery console with Cmd-R where I ran Disk Utility. The main partition was not repairable and required re-formatting ("Erase" in the recovery console parlance). After reformatting I rebooted into the recovery console again and was able to restart the installation. Assuming it goes well I will have a fresh install and will restore from Time Machine.
Whatever the issue was with the failed installation last time, it is likely that the issue existed before I tried the install, as I was unable to boot from the CCC clone at all.
This will be the first clean install of OS X for me since 10.2 (all others have been upgrades) so hopefully that wlll fix my issues. Once I have restored from TM I will wipe my clone and re-run CCC to be up to date - and will verify after that I can boot from the clone. Good times ....

ISCSI target setup fails: command "iscsitadm" not available?

Similar Messages

Maybe you are looking for