Iscsi teaming windows 2012r2 service profile

hi I have a 2012r2 server with 8 vnics configured
vnic0, vnic1 ----> management
vnic2,3 -----> iscsi1
vnic4,5 -----> iscsi2
each nic goes to different fabric.
In order to get redundancy and failover, do I team these nics up for iscsi in windows? or should i just use 1 nic per fabric and do mpio?
I am not sure how many nics to use for failover and redundancy for iscsi in 2012
any ideas?

For more information check like as well.
http://blog.augustoalvarez.com.ar/2014/03/27/step-by-step-creating-a-windows-server-2012-r2-failover-cluster-using-starwind-iscsi-san-v8/.
http://cscmblog.blogspot.ch/2012/11/windows-2012-how-to-configure-multi_13.html

Similar Messages

Ix4-300d iSCSI disconnect Windows 2012R2

Hello Everyone,
I just recently purchased (3 days ago) an ix4-300D and updated it to the latest patch. I have 4 x WD 3TB Disks and they are configured with a raid 0 configuration. I then have 2 NICs (not bonded) and using the second port for the iSCSI LAN (192.168.100.100, Jumbo Frames 9000) and the 1st port for accessing the device (192.168.1.100). I carve out 3 TB iSCSI LUN (with CHAP) and give it a name. My Windows Server sees this (under the 192.168.100.X network) and I"m able to bring it online, mount it, format it and use the LUN. I then start copying about 2.5 TB of Data off an ix2 back to this Ix4 and about 1/4 through the copy, the iSCSI disconnects and the actual unit is frozen., It won't respond to web interface on the 192.168.1.x LAN either. I have to actually unplug it and then plug it back in for the unit to respond. I know that iSCSI works on the Window Server as I replaced a custom NAS Server using OpenFiler and worked for over 2 years w/o issues/reboots or anything else. The only thing that has changed is the NAS box (the ix4-300d). Can anyone think of anything I could be doing wrong? What to check? I am thinking it is a bad unit but I want to check everything first.
I will say the only thing that *could* be out of line (but is VERY doubtful is the problem) is that 3 of the WD drives are 3TB Reds and 1 is a 3 TB Black. I'm going to remove the black drive and redo the entire unit to see if that resolves the problem but I doubt it will. I know the Reds are "certified".
I have already removed the Jumbo Frames just in case (though the windows networking card supports Jumbo Frames 9000 since the old SAN was working with these w/o issue).
Thoughts anyone???

Hello CPXGreg
Using a mixed disk array can cause instabilities, so I do recommend that you try using the unit without the WD Black disk for at least testing.
Next, there are various factors that could cause or contribute to a firmware lock like this. Usually this is caused by media server crashing, which then escalates to a full firmware lock. I recommend checking that media server has been turned off for now and any unused protocols. If the unit still locks up I recommend that you contact LenovoEMC support to have a dump report from the unit reviewed. This way we can check what may be at the root of the issue.
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/

Error in Windows 7: User Profile Service was not logged on. The user and administratorprofile

Error in Windows 7: User Profile Service was not logged on. The user profile can not be loaded. Administrator profile and the code does not work. What do I do?
HP G5384sc desktop pc

Hello
Unfortunately I did not manage to fix my computer yet. My printer is broken so I bought a new one, but since I do not have administrator rights, I can not connect the new printer, so I have to write all-installing notes down with pencil and simultaneously translate them into Danish so it is a very slow process. I'll tell you if it succeeds, otherwise there is of course the primitive way to buy a new computer, but it's the same as giving up. Not yet.
Until now, many thanks for the good suggestions.
Kind regards
Birgeres

Windows Deployment Service. Network Profile Radio Buttons greyed out with R2

Hi All
I have downloaded and setup Server 2008 R2 (not yet activated). I have added the following roles "DHCP Server", "DNS Server", "Active Directory Domain Services" and "Windows Deployment Services". I can PXE boot a test client machine and (using the boot.win from windows 7 dvd) multicast a XP Image to it. This setup is connected via a 100 Mb switch and is an isolated network.
Under windows deployment services - if I right click my server - select properties - network tab "Network Profile is greyed out". I have tried running wdsutil /Set-TransportServer /Server:big /Profile:100Mbps but get the following error message: "Windows Deployment Services Management Utility Version 6.1.7600.16385. Error code 0xC110011F This WDS transport server does not support network profiles.
I have tried this on two hardware setups:
An Intel D915GUX 3GHz 2GB RAM and Marvel Yukon 88E8050 ethernet controller.
An Intel D965 Core2Duo 1.86GHz 2GB RAM and Intel 82566DM Network controller.
Incidently I have done the same setup with Server 2008 (not R2) on the D965 and the Network Profile radio buttons are not greyed out. If I upgrade the same test machine to server 2008 R2 the Network Profile radio buttons are greyed out. Is this a design change, does Server 2008 R2 no longer support network profiles as I am now unable to select 10 100 or 1000 Mbs ?
If more information is required or if anything needs further detail please let me know.
Thanks for any help.
Liam.D

Is there any way at all to manually set or control the network profile? In my environment, a SCCM\WDS multicast stream is bottoming out on speed and network utilization when the stream crosses a Nexus 7009 router. Speeds go from 200 Mbps to 20 mbps. I have
a theory that this "new" automatic configuration is placing the clients in a slow network profile that are on the opposite side of the router and I have been unable to find a way to speed of the transmission. I have also ruled out the "master
client" slowing down the stream buy using different clients only connecting to a stream 1 at a time. I have also ruled out the router as the source of the problem by having a VLC client listen to the multicast stream on the same side of the router as
the slow clients. The VLC client (unknown to SCCM\WDS) was able to receive the transmissions at 20 % utilization / 200 Mbps.
-Tony

Failing to install Domain Services on a Windows 2012R2 without internet connection

Hello
i have a windows 2012r2 server without internet connection.
when i try to add the Domain Services role it failed in the Feature installation phase
i even tried to provide an alternate location from a ISO source but that didn't help either
im lost here what should i do?
i attached the fail screenshot
Thanks
Guy

What error is shown in Event Viewer when the install fails?
Is it the first 2012 R2 DC in a lower level domain?
Try installing ADDS via PowerShell:
Import-Module ServerManager
Install-windowsfeature -name AD-Domain-Services –IncludeManagementTools
The other thing that it could be is an issue with the WID (Windows Internal Database)
Check in the Event Viewer for anything to do with Service: MSSQL$MICROSOFT##WID and perhaps try this:
Adjust your domain (or domain controller if appropriate) security policy to allow “NT SERVICE\MSSQL$MICROSOFT##WID” to log on as a service, a GPO setting that can be found under Computer Configuration > Policies > Windows Settings > Security Settings
> Local Policies > User Rights Assignment.
Kind Regards
Michael Coutanche
Blog:
Twitter: LinkedIn:
Note: Posts are provided “AS IS” without warranty of any kind, either expressed or implied, including but not limited to the implied warranties of merchantability and/or fitness for a particular purpose.

ConfigMgr 2012R2 / Software Update feature - Windows Update Service on clients

Hi,
ConfigMgr 2012R2 / Software Update feature.
Is it necessary that the Windows Update Service on clients is running???
Thanks

It doesn't have to be running Automatic if that's what you're asking, but it shouldn't be
Disabled either. The ConfigMgr client will trigger it to scan for updates. For a nice documentation about the whole process see:
http://blogs.technet.com/b/configmgrdogs/archive/2014/06/30/configmgr-2012-windows-update-client-process.aspx
My Blog: http://www.petervanderwoude.nl/
Follow me on twitter: pvanderwoude

Hyper V Integration Components of Windows 2012R2

Hi Team,
I am receiving the above error during installation of Hyper Integration Components of Windows 2012R2.
VM OS is windows 2008 std Sp2
Hyper is WIndows 2012 R2.
I have created a VM from Physical server to Virtual.
Please suggest me the solution

Hi Sr ,
You were using disk2vhd to P2V ？
Did you try to install integration services offline ?
Please refer to the article below :
http://blogs.technet.com/b/virtualization/archive/2013/04/19/how-to-install-integration-services-when-the-virtual-machine-is-not-running.aspx
Before doing this please try to copy the VHD to another VM and test .
Best Regards
Elton Ji
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Service Profiles Migration between Server M2 and M3

Hi Cisco Top Guns!!!
I have tried to migrate some service profiles between servers M2 (with M81KR) to M3 (with Vic 1240 and Vic 1280) and Windows 2008 R2 recognized the interfaces on M3 as new interfaces.
The ghost devices interfaces (old interfaces) still presents on Windows and to rename the new interfaces or apply the same IP configurations, I need to remove the ghosts interrfaces.
On my opinion, this change goes against the UCS philosophy.
I have a case opened with Cisco Developed Team and now Im sharing this issue with the community. Anyone have benn passed for this problem too?
Regards,
Fábio Henrique Teixeira - System ITS

This is a hardware change to the operating system. While UCSM can abstract the MAC/WWPN/WWNN information, the operating system recognizes a hardware adapter difference and will instatiate new devices. This is an OS issue. Some OS's (Linux) will allow you to set a flag to ignore the hardware change. I'm not aware of whether and what versions of Windows that will allow the same behavor. We cannot modfy the hardware identification change, as we use it within UCSM to manage allowable firmware bundles and adapter polices (vnics/vhbas/fabric failover)

Remote App and Desktop RDP client never succeed to logon the RDS gateway server running Windows 2012R2

Remote App and Desktop RDP client never succeed to logon the RDS gateway server running Windows 2012R2
1. Client Os : Windows 7 Pro
2. Server OS : Windows Server 2012R2 with RDS broker and RDS Gateway server with 3.part Certificate with friendly name sky.mti-itservice.no activated.
The main problem is following: The RDP logon session never ends
Any ideas ?
Regards
Kenneth Knudsen
Email : [email protected]
mvh Kenneth Knudsen MCSE 2003 HP ASE

Hi Kenneth,
Here for your case suggest you to configure RDP session time limit so that your user can disconnect\log off once the specific time limit reached.
You can setup the session time limit in different method.
1. Open the Server Manager, select Remote Desktop Services.
2. In Remote desktop Services, in right side you can drop down to collections.
3. Select the collection which you want to edit the settings.
4. Under collections Properties, select Task and then Edit Properties.
5. In Properties dialog box, select Session.
6. You can find all thetimeout settings under session collection properties; edit according to your requirements and then OK.
And apart also by group policy setting as below.
Computer Configuration\Policies\Administrative Templates\Windows Components\Remote Desktop Services\Remote Desktop Session Host\Session Time Limits
User Configuration\Policies\Administrative Templates\Windows Components\Remote Desktop Services\Remote Desktop Session Host\Session Time Limits
- Set time limit for disconnected sessions
- Set time limit for active but idle Remote Desktop Services sessions
- Set time limit for active Remote Desktop Services sessions
- End session when time limits are reached
Please check which setting suitable for your environment and you can apply for your case.
[Forum FAQ] Restrict number of Active Sessions in RDS 2012 and 2012 R2
https://social.technet.microsoft.com/Forums/en-US/00c2252b-8ec0-489f-8da2-07a434a9b5a2/forum-faq-restrict-number-of-active-sessions-in-rds-2012-and-2012-r2?forum=winserverTS
Hope it helps!
Thanks.
Dharmesh Solanki
TechNet Community Support
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Sharepoint 2010 on Windows 2012R2 and claims based authentication

Hello,
We have installed a sharepoint 2010 SP2 CU dec 2014 on a Windows 2012R2 server.
The installation went without problems.
However, we want to use claims based authentication on a certain web app pool.
Therefore some configuration on IIS is required.
The first issue we ran into, is the web application pool uses ASP.NET 2.0, which is the default settings.
However, using this ASP.NET Version 2.0 the feature "Providers" and ".net users" are invisible.
When changing the .net version to 4.0, the features comes back again.
I can fill in the connection strings without problem.
The providers feature however, gives me the following errors:
There is a duplicate .... sections defined.
When googling on this error, it seems that on .net 4.0 these sections are already globbally defined in the machine.config, So i removed these entries in the machine.config
These are the lines that are "double"
<section name="scriptResourceHandler" type="System.Web.Configuration.ScriptingScriptResourceHandlerSection, System.Web.Extensions, Version=4.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" requirePermission="false"
allowDefinition="MachineToApplication"/>
<section name="jsonSerialization" type="System.Web.Configuration.ScriptingJsonSerializationSection, System.Web.Extensions, Version=4.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" requirePermission="false" allowDefinition="Everywhere"
/>
<section name="profileService" type="System.Web.Configuration.ScriptingProfileServiceSection, System.Web.Extensions, Version=4.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" requirePermission="false" allowDefinition="MachineToApplication"
/>
<section name="authenticationService" type="System.Web.Configuration.ScriptingAuthenticationServiceSection, System.Web.Extensions, Version=4.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" requirePermission="false"
allowDefinition="MachineToApplication" />
So after removing these lines, i can get into Providers feature in IIS.
but, when i click on "Add..." i get the following error:
Add Provider
There was an error while performing this operation.
Details:
This method cannot be called during the application's pre-start initialization phase.
OK
I spent to much time already to solve this issue and i hope that someone can give me some advice to address this issue.

The STS web.config:<?xml version="1.0" encoding="utf-8"?>
<configuration>
<system.serviceModel>

<behaviors>
<serviceBehaviors>
<behavior name="SecurityTokenServiceBehavior">

<serviceMetadata httpGetEnabled="true" />

<serviceThrottling maxConcurrentCalls="65536" maxConcurrentSessions="65536" maxConcurrentInstances="65536" />
</behavior>
</serviceBehaviors>
</behaviors>

<services>
<service name="Microsoft.IdentityModel.Protocols.WSTrust.WSTrustServiceContract" behaviorConfiguration="SecurityTokenServiceBehavior">

<endpoint address="" binding="customBinding" bindingConfiguration="spStsBinding" contract="Microsoft.IdentityModel.Protocols.WSTrust.IWSTrust13SyncContract" />

<endpoint name="ActAs" address="actas" binding="customBinding" bindingConfiguration="spStsActAsBinding" contract="Microsoft.IdentityModel.Protocols.WSTrust.IWSTrust13SyncContract" />

<endpoint address="mex" binding="mexHttpBinding" contract="IMetadataExchange" />
</service>
<service name="Microsoft.SharePoint.Administration.Claims.SPWindowsTokenCacheService">
<endpoint address="" binding="customBinding" bindingConfiguration="SPWindowsTokenCacheServiceHttpsBinding" contract="Microsoft.SharePoint.Administration.Claims.ISPWindowsTokenCacheServiceContract" />
</service>
</services>

<bindings>
<customBinding>
<binding name="spStsBinding">
<binaryMessageEncoding>
<readerQuotas maxStringContentLength="1048576" maxArrayLength="2097152" />
</binaryMessageEncoding>
<httpTransport maxReceivedMessageSize="2162688" authenticationScheme="Negotiate" useDefaultWebProxy="false" />
</binding>
<binding name="spStsActAsBinding">
<security authenticationMode="SspiNegotiatedOverTransport" allowInsecureTransport="true" defaultAlgorithmSuite="Basic256Sha256" messageSecurityVersion="WSSecurity11WSTrust13WSSecureConversation13WSSecurityPolicy12" />
<binaryMessageEncoding>
<readerQuotas maxStringContentLength="1048576" maxArrayLength="2097152" />
</binaryMessageEncoding>
<httpTransport maxReceivedMessageSize="2162688" authenticationScheme="Negotiate" useDefaultWebProxy="false" />
</binding>
<binding name="SPWindowsTokenCacheServiceHttpsBinding">
<security authenticationMode="IssuedTokenOverTransport" />
<textMessageEncoding>
<readerQuotas maxStringContentLength="1048576" maxArrayLength="2097152" />
</textMessageEncoding>
<httpsTransport maxReceivedMessageSize="2162688" authenticationScheme="Anonymous" useDefaultWebProxy="false" />
</binding>
</customBinding>
</bindings>
</system.serviceModel>
<system.webServer>
<security>
<authentication>
<anonymousAuthentication enabled="true" />
<windowsAuthentication enabled="true">
<providers>
<clear />
<add value="Negotiate" />
<add value="NTLM" />
</providers>
</windowsAuthentication>
</authentication>
</security>
<modules>
<add name="WindowsAuthenticationModule" />
</modules>
</system.webServer>
<system.net>
<connectionManagement>
<add address="*" maxconnection="10000" />
</connectionManagement>
</system.net>
<connectionStrings>
<add connectionString="Server=sqldb_qa_sharepoint2010;Database=SG_SHP_Claims_Authentication;Integrated Security=true" name="SHP_Claims_Authentication" />
</connectionStrings>
</configuration>
I have backupped the machine.config and restored it (the file i edited was in the following dir: C:\Windows\Microsoft.NET\Framework\v4.0.30319\Machine.config)

TF400893: Team Foundation Server services are not available.

Hi Gang
Am getting
TF400893: Team Foundation Server services are not available. This is most likely caused by a network error. Please check your connection and try again.
consistently when trying to access TFS2012 Web Access. I'm on the same domain as the server and able to login however as soon as I try and access a query it asks me to log in again and then presents me with the above message.
Any thoughts am trying to get as many ports open as possible however security's pretty tight here.
Regards

Hi,
Thanks for your feedback!
I recommend you install TFS Power Tools and run a Team Foundation Server Complete Health Check and see if it helps.
TFS 2012 Power Tools download address:http://visualstudiogallery.msdn.microsoft.com/b1ef7eb2-e084-4cb8-9bc7-06c3bad9148f
Hope it helps!
Best Regards,
Cathy Kong
MSDN Community Support | Feedback to us
Develop and promote your apps in Windows Store
Please remember to mark the replies as answers if they help and unmark them if they provide no help.

Windows Firewall Service Crashes on Windows Server 2012

Hello Team,
I am facing issues with Windows Firewall Service in new Windows 2012 R2 deployments. when i try to start the Firewall service it wont start and it throws an error message to check the system event logs for information
The Windows Firewall service terminated with the following service-specific error:
The data is invalid.
I deployed this OS on a VM running with latest VM tools and HW version which is running on ESXi 5.1 U1
2 GB RAM, 1 vCPU
OS deployed through ISO downloaded from MS portal and License activated through KMS system, performed a couple of reboots as well.
any advise on this issue? i am sure some of you might have also faced the same issue

1. VMware support forum and knowledge base may give you more specific advice.
2. Windows services may be dependent on another service(s). Analyze these dependences. Do it after you understand implications of VMware firewall function.
3. More detailed info from Event log is needed for analysis (Event ID, etc)
4. Hope you have connectivity configured correctly.
5. For firewall in VMware read the following article(s):
http://pubs.vmware.com/vsphere-51/index.jsp?topic=%2Fcom.vmware.vsphere.security.doc%2FGUID-52188148-C579-4F6A-8335-CFBCE0DD2167.html&__utma=207178772.2027713003.1393320147.1393320147.1393320147.1&__utmb=207178772.0.10.1393320147&__utmc=207178772&__utmx=-&__utmz=207178772.1393320147.1.1.utmcsr=google|utmccn=(organic)|utmcmd=organic|utmctr=(not%20provided)&__utmv=-&__utmk=174193441
Regards
Milos

Windows Search Service Best Pratices on RDP Server with office 2013

high everybody,
i´m looking for guide how to configure the Windows Search Service on our Server 2012 RDS Servers. The Servers have Office 2013 installed so turning off the Search Service is not an Option. We are using User Profile disks and logoff was getting slower
as time goes by. Reading in another thread if have deleted the Subkeys under
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows Search\CrawlScopeManager\Windows\SystemIndex\DefaultRules
and restarted the Search Service.
This Resulted in a lighning fast logoff ( less then 5 Seconds) before that logoff took up to 2 Minutes. Looking at the Reg Key´s i found that underneth the mentioned Key there was a subkey for each user that has EVER loged on to this Server. Normal load
should be about 30 Users and i found about 700 subkey´s. To it seems that this causes the Search Service searchindexer.exe to read thru all this key´s witch i think is not the Problem ( Internet Explorer does far more reads and writes) but what happens
with the Information.
Maybe it has to to with the fact, that we are using User Profile Disks ?
In the Search Service Policy i have excluded "C:","users homedrive" and the Share where the Users share theyr data, for the Search Service to exclude.
So does anybode have experience with Seach Service on RDS Servers with Office maybe with User Profile Disks ?
Thanks Reiner

Hi Reiner,
You can check the following article might helpful to resolve your case.
Incomplete search results may occur in Outlook when a PDF iFilter is installed
http://support.microsoft.com/kb/2925203/en-us
Also try uninstalling office 2013 application and then reinstall by running change user /install command in elevated command prompt on RDS server prior to install software's. Post software installation you need to run
change user /execute command on server
http://technet.microsoft.com/en-us/library/cc742815.aspx
Hope it helps!
Thanks.
Dharmesh Solanki
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Can't add a new vNIC for service profile

Hello,
I'm trying to add an additional vNIC for Service Profile.
B200-M3, VIC1240+expander, IOM 2208XP, 4 links between IOM and FI 6248, firmware 2.2(1f).
At the moment 7 vNICs are configured for this service profile. Service profile is associated with blade server.
When I try to add a new vNIC (it will be 8th vNIC), I see the error (see the attachment).
For some reasons separate vNICs are more useful for Hyper-V servers :)
All vNICs created via vNIC templates. All vNICs configured as VMQ, only iSCSI configured as Dynamic,
As I read the spec, VIC1240 can support up to 250 vNICs. What is wrong ? How to fix that ?

I have seen the VMQ limit being reached when applying the VMQ policy to the vNIC template. Can you try not selecting the VMQ policy for these new vNICs. If this works, you might be reaching the VMQ limits as described below:
Number of VMQ's:
128 is the Maximum number per vNIC
256 is the max number per Blade

Getting Server Error Code: -2147024891 when using Biztalk Windows SharePoint Services Adapter to upload a document

We are currently running
1. BizTalk Server 2013 R2
2. SharePoint 2013
both in a Windows 2012 Server environment, in Azure.   The BizTalk and SharePoint are running on separate machines.
I am using the Windows SharePoint Adapter to upload a Tif file to a SharePoint document library. However, when the host instance is running under my team member's userid, I get the following error in the eventlog:
The adapter failed to transmit message going to send port "SendOwnershipToSharePoint" with URL "wss://bp1amsapt218:34392/sites/BiztalkSc/Lists/Ownership". It will be retransmitted after the retry interval specified for this Send Port.
Details:"[Microsoft.SharePoint.Client.ServerUnauthorizedAccessException] Access denied. You do not have permission to perform this action or access this resource. Server Error Code: -2147024891Trace:    at Microsoft.SharePoint.Client.ClientRequest.ProcessResponseStream(Stream
responseStream)
   at Microsoft.SharePoint.Client.ClientRequest.ProcessResponse()
   at Microsoft.SharePoint.Client.ClientRequest.ExecuteQueryToServer(ChunkStringBuilder sb)
   at Microsoft.SharePoint.Client.ClientRequest.ExecuteQuery()
   at Microsoft.SharePoint.Client.ClientRuntimeContext.ExecuteQuery()
   at Microsoft.SharePoint.Client.ClientContext.ExecuteQuery()
   at Microsoft.SharePoint.Client.Web.WebUrlFromPageUrlDirect(ClientContext context, Uri pageFullUrl)
   at Microsoft.BizTalk.KwTpm.WssAdapter.ClientOmAccessor.RequestInfo..ctor(String siteUrl, String sharePointOnlineUsername, String sharePointOnlinePassword)
   at Microsoft.BizTalk.KwTpm.WssAdapter.ClientOmAccessor.ListsAccessor..ctor(String siteUrl, String sharePointOnlineUsername, String sharePointOnlinePassword)
   at Microsoft.BizTalk.KwTpm.WssAdapter.ClientOmAccessor.ListsAccessor.TryOpenWebSite(String siteUrl, String sharePointOnlineUsername, String sharePointOnlinePassword, Exception& lastError)
This error was triggered by the Windows SharePoint Services receive location or send port with URI wss://bp1amsapt218:34392/sites/BiztalkSc/Lists/Ownership.
Windows SharePoint Services adapter event ID: 12310".
This userid has already been added to the following groups on the BizTalk Server:
Local Administrators Group
BizTalk Server Administrators
SSO Administrators
BizTalk Isolated Host Users
BizTalk Application Users
I have also made sure the userid has full control access to the SharePoint site and the document library within the site.   I have confirmed that the user with this userid is able to access the SharePoint site and can upload documents to the
document library, manually.   However, when the host instance is running under this userid, I am not able to upload documents to the SharePoint document library.
The Windows SharePoint Services Adapter is configured with the following values:
Adapter Web Service Port:   34392
Timeout:   100000
Use Client OM: Yes
Destination Folder URL: Lists/Ownership
FileName: test.tif
Overwrite: Yes
SharePoint Site URL:
http://bp1amsapt218:34392/sites/BiztalkSc/
Microsoft Office Integration: No
Do you know what the cause for this error is?   We urgently need a resolution for this?

If you create an XML document and upload it to the Windows SharePoint Services Web site. The Windows SharePoint Services adapter will take that message, archive it in the Archive document library, and then send it to the Destination document library. This
procedure demonstrates how a document flows from a Sharepoint web site, through BizTalk Server, and to a Sharepoint Services Web site using the Windows Sharepoint Services adapter.
This MSDN library article shows the procedure, please check whether it will be helpful to troubleshoot.
Create a working directory
Create an XML file
Upload the XML file
See: https://msdn.microsoft.com/en-us/library/aa560513.aspx

Iscsi teaming windows 2012r2 service profile

Similar Messages

Maybe you are looking for