ISDN BRI - debug output

Hi,
I am having follwoingg output of debug ISDN commands. I am same output for many routers. ( unfound b cahnnel).
What could be the reason ? It is unable to bring up the interface. It doesnt seem to be IOS problem as same IOS is working at other places. Can it be a problem with Service provider some settings in ISDN switch ?
Debug output is
ISDN BR0 EVENT: process_rxstate: ces/callid 1/0x8008 calltype 1 HOST_DISCONNECT_ACK Nov 19 09:07:14 CET: ISDN BR0 **ERROR**: host_disconnect_ack: Unfound B-channel on Disconnect_Ack call id 0x8008.
Thanks in advance

Hey ,
Here are the codes for disconnect . Becoz i dont see ur complete output after ping + debug q931 -- kindly check the code in the following link.
if more help needed ..paste the above mentioned + sh isdn status.
Suspect a Telco issue. <<
http://www.cisco.com/warp/public/129/isdn_disc_code.html#
rate the post if helps ....

Similar Messages

ISDN debug output

Hi,
I am giving here output of isdn debug command q931 and q921. but I am not in a position to find out what is the problem.
Is it related with serivce provides or with router. I am giving debug output at three different locations.
Pls see the attachment
Thanx in advance.
Subodh

this seems like a physical failure from the looks. (hardware, cabling....)
it could be a configuration error but i've never seen this type of isdn debug output with the typical configuration errors. (could be telco issue at their switch but haven't see this output from a telco idsn issue either)
clearly there is a problem with the router being able to allocate a B channel.
i see you get a TEI assigned. do you ever see MultiFrame Established? (show isdn status)
what version IOS?
please post your configuration if possible so we can see if anything wrong there.

Problem connecting isdn bri voice interface to pstn

i'm trying to configure my ISDN BRI NT/TE voice interface card (VIC-2BRI-NT/TE) on router 3825 to link to my PSTN provider. This must allow my Cisco IP phones to pass call to the PSTN through my call manager 4.1.
I suscribe to two isdn line. The provider told me that the SWITCH TYPE is VN6 (COTE d'IVOIRE or Ivory Coast).
For my bri configuration, see file "interfaces configuration..."
My problem is that when i pass call from my Ip telephony network, the first call goes well. But after this first call, when i type the command isdn status, i can see that the layer 1 of my isdn interfaces are DEACTIVATED, and after a few minutes, it turn back to ACTIVE. During these minuite, i can't pass any call through my isdn interface.
for outputs of show isdn status command, and isdn debug q931 commands
see file "show isdn status and debug..."
Notice: when the status of the isdn layer is in the deactvated status, i can receive call from the pstn, but i can't passe call to pstn (the state changes to ACTIVE when incomming call from pstn arrive, but still stay DEACTIVATED when outgoing call is initiated)
Please help me

I've entered the "isdn transition-delay 1" interface command and things seem to work well.According to the IOS help on my router,this command clears the ISDN D-CHANNEL after a delay of 1 second.
But i would like to get more information on this command, and also on the isdn layer 2 and 3 timers, and even possible on all the "isdn" interface command option.
THANKS

ISDN BRI connection won't stay up

Hi all,
I'm trying to get the S/T port on 3 routers to connect thru ISDN BRI. Thus far I've only been able to get this to work on a 1601.
My attempts on an 878 and a soho96 are less succesfull.
Both are able to establish a connection, but it won't stick.
Attached is the output of the debug isdn q921. The top shows the succesfull connection on the 1601, the bottom shows the other result. The only discrepancy I can find is the lack of a IS.DN BR0: TX -> INFOc message after the tei exchange is succesfull.
I am in the dark however on whether this is a symptom or the cause of the problem. Searches on the cisco domain don't turn up much on this part of the layer 2 troubleshooting.
Any thoughts are welcome on this subject.
Regards
Wouter

Hello,
there is an earlier thread (see the link below), where the problem was related to the fact that the 878 needs the Advanced Enterprise IOS (and not the Advanced IP Services IOS) for the ISDN interface to function, you might want to check if you are running into the same issue.
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Network%20Infrastructure&topic=WAN%2C%20Routing%20and%20Switching&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1dd96928/10#selected_message
Regards,
GNT

No dialer command under ISDN BRI interface

Hi all,
I have a 2901 router voice bundle with 4 ISDN BRI ports and would like to have them bundled under Dialer1 interface. Unfortunately it doesn't give me option for Dialer command under BRI interface as expected.
router(config-if)#int bri0/0/0
router(config-if)#dia
router(config-if)#dia
^
% Invalid input detected at '^' marker.
router(config-if)#dialer
^
% Invalid input detected at '^' marker.
router(config-if)#
I assume it's down to the UC license installed on the device but not sure. Does the ISDN BRI interface behave in different way under this license?
Pasting portion of "show ver" as well.
Cisco CISCO2901/K9 (revision 1.0) with 479232K/45056K bytes of memory.
Processor board ID
2 Gigabit Ethernet interfaces
4 ISDN Basic Rate interfaces
1 terminal line
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
License Info:
License UDI:
Device# PID SN
*0 CISCO2901/K9
Technology Package License Information for Module:'c2900'
Technology Technology-package Technology-package
Current Type Next reboot
ipbase ipbasek9 Permanent ipbasek9
security None None None
uc uck9 Permanent uck9
data None None None
Configuration register is 0x2102

Hi,
Snippet of "sh ver" with IOS version is below:
router#show ver
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.2(4)M5, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Fri 13-Sep-13 14:59 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M16, RELEASE SOFTWARE (fc1)
router uptime is 2 days, 21 hours, 47 minutes
System returned to ROM by reload at 16:48:03 UTC Mon Aug 18 2014
System restarted at 16:50:01 UTC Mon Aug 18 2014
System image file is "flash0:c2900-universalk9-mz.SPA.152-4.M5.bin"
Last reload type: Normal Reload
Last reload reason: Reload Command
The output of trying to type dialer command is in the initial post, I'm also pasting all available commands under bri0/0/0.
router(config-if)#int bri0/0/0
router(config-if)#?
Interface configuration commands:
aaa Authentication, Authorization and Accounting.
access-expression Build a bridge boolean access expression
arp Set arp type (arpa, probe, snap), timeout, log
options or packet priority
authentication Auth Manager Interface Configuration Commands
autodetect Autodetect Encapsulations on Serial interface
bandwidth Set bandwidth informational parameter
bgp-policy Apply policy propagated by bgp community string
bridge-group Transparent bridging interface parameters
carrier-delay Specify delay for interface transitions
cdp CDP interface subcommands
clns CLNS interface subcommands
clock Configure serial interface clock
cwmp Configure CPE WAN Management Protocol(CWMP) on this
interface
dampening Enable event dampening
default Set a command to its defaults
delay Specify interface throughput delay
description Interface specific description
dot1q dot1q interface configuration commands
dot1x Interface Config Commands for IEEE 802.1X
down-when-looped Force looped serial interface down
encapsulation Set encapsulation type for an interface
ethernet Ethernet interface parameters
exit Exit from interface configuration mode
flow-sampler Attach flow sampler to the interface
full-duplex Configure full-duplex operational mode
h323-gateway Configure H323 Gateway
half-duplex Configure half-duplex and related commands
help Description of the interactive help system
history Interface history histograms - 60 second, 60 minute
and 72 hour
hold-queue Set hold queue depth
ip Interface Internet Protocol config commands
iphc-profile Configure IPHC profile
ipv6 IPv6 interface subcommands
isdn ISDN Interface configuration commands
isis IS-IS commands
iso-igrp ISO-IGRP interface subcommands
keepalive Enable keepalive
line-power Provide power on the line.
llc2 LLC2 Interface Subcommands
load-interval Specify interval for load calculation for an
interface
logging Configure logging for interface
loopback Configure internal loopback on an interface
mab MAC Authentication Bypass Interface Config Commands
mac-address Manually set interface MAC address
macro Command macro
metadata Metadata Application
mop DEC MOP server commands
mtu Set the interface Maximum Transmission Unit (MTU)
netbios Use a defined NETBIOS access list or enable
name-caching
network-clock-priority Configure clock source priority
no Negate a command or set its defaults
ntp Configure NTP
ospfv3 OSPFv3 interface commands
pulse-time Force DTR low during resets
rate-limit Rate Limit
redundancy RG redundancy interface config
routing Per-interface routing configuration
sdllc Configure SDLC to LLC2 translation
serial serial interface commands
service-policy Configure CPL Service Policy
shutdown Shutdown the selected interface
smds Modify SMDS parameters
snapshot Configure snapshot support on the interface
snmp Modify SNMP interface parameters
source Get config from another source
tarp TARP interface subcommands
timeout Define timeout values for this interface
topology Configure routing topology on the interface
transmit-interface Assign a transmit interface to a receive-only
interface
trunk-group Configure interface to be in a trunk group
tx-ring-limit Configure PA level transmit ring limit
vpdn Virtual Private Dialup Network
vrf VPN Routing/Forwarding parameters on the interface
waas WAN Optimization
router(config-if)#

ISDN BRI layer 1 & layer 2 do not sustain "active" statuses

Hi Expert,
I have some routers which can not sustain the ISDN layer 1 & layer 2 statuses correctly. Whenever, the ISDN line is manually activated or the ISDN BRI ports are manually reset, the layer 1 & layer 2 statuses become active but they become deactivated after a while. I have changed the ISDN module and the same symptom is observed. Would you advise what is the cause and resolution. Your advice in this matter is greatly appreciated.
Thanks and Regards,
Jason Peh

Hi Rick,
Below is the show interface for BRI1/0,
router_2#sh isdn status
Global ISDN Switchtype = basic-net3
ISDN BRI1/0 interface
dsl 8, interface ISDN Switchtype = basic-net3
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
TEI = 66, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
Layer 3 Status:
0 Active Layer 3 Call(s)
Activated dsl 8 CCBs = 0
The Free Channel Mask: 0x80000003
router_2#sh int BRI1/0
BRI1/0 is up (spoofing), line protocol is up (spoofing)
Hardware is BRI
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
Last input 00:04:39, output 00:04:39, output hang never
Last clearing of "show interface" counters 24w4d
Input queue: 0/75/0 (size/max/drops); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/16 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
27807 packets input, 207167 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
27921 packets output, 209138 bytes, 0 underruns
0 output errors, 0 collisions, 551 interface resets
0 output buffer failures, 0 output buffers swapped out
1680 carrier transitions
router_2#sh int BRI1/0:1
BRI1/0:1 is down, line protocol is down
Hardware is BRI
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
Keepalive set (10 sec)
LCP Closed, multilink Closed
Last input 04:59:17, output 04:59:17, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/40, 108 drops; input queue 0/75, 1 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
7434 packets input, 1689890 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
2 input errors, 0 CRC, 1 frame, 1 overrun, 0 ignored, 1 abort
10743 packets output, 782350 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
4682 carrier transitions
router_2#sh int BRI1/0:2
BRI1/0:2 is down, line protocol is down
Hardware is BRI
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
Keepalive set (10 sec)
LCP Closed, multilink Closed
Last input 04:59:22, output 04:59:22, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/40, 3 drops; input queue 0/75, 3 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
6902 packets input, 1530090 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
3 input errors, 0 CRC, 3 frame, 0 overrun, 0 ignored, 3 abort
7527 packets output, 594592 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
25 carrier transitions
I have another router with the same configuration and the statuses are able to sustain correctly. Thus, I doubt that the backup interface command has any effect on the layer 1 & layer 2 statuses.
Best Regards,
Jason Peh

ISDN BRI backup - Disconnect after 1 sec

There is a ISDN BRI backup to Serial IF on a router.BRI seems to be able to cennect with opossite site, but after 1 sec comes Disconnect(see attachment).I tried Floating static routes and Dialer watch as well, with the same result. Can anybode help me? Thanks

There is no aaa new-model statment on both side.I`ve rewrite user/psw and added ppp chap hostname ... command.
output of isdn status follows:
cpp-poprad#
Sep 20 14:52:00.647: %DIALER-6-BIND: Interface BR0/1/0:1 bound to profile Di0
Sep 20 14:52:00.651: %LINK-3-UPDOWN: Interface BRI0/1/0:1, changed state to up
Sep 20 14:52:00.651: %ISDN-6-CONNECT: Interface BRI0/1/0:1 is now connected to 0524684841 N/A
Sep 20 14:52:01.655: %ISDN-6-CONNECT: Interface BRI0/1/0:1 is now connected to 0524684841 cpp-poprad
Sep 20 14:52:01.655: %ISDN-6-DISCONNECT: Interface BRI0/1/0:1 disconnected from 0524684841 cpp-poprad, call lasted 1 seconds
Sep 20 14:52:01.659: %LINK-3-UPDOWN: Interface BRI0/1/0:1, changed state to down
Sep 20 14:52:01.659: %DIALER-6-UNBIND: Interface BR0/1/0:1 unbound from profile Di0sh isdn statu
Global ISDN Switchtype = basic-net3
ISDN BRI0/1/0 interface
dsl 2, interface ISDN Switchtype = basic-net3
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 71, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 2 CCBs = 0
The Free Channel Mask: 0x80000003
Total Allocated ISDN CCBs = 0
cpp-poprad#sh isdn act
ISDN ACTIVE CALLS
Call Calling Called Remote Seconds Seconds Seconds Charges
Type Number Number Name Used Left Idle Units/Currency
cpp-poprad#
Sep 20 14:52:18.295: %LINK-3-UPDOWN: Interface BRI0/1/0:1, changed state to up
Sep 20 14:52:18.295: %DIALER-6-BIND: Interface BR0/1/0:1 bound to profile Di0
Sep 20 14:52:18.299: %ISDN-6-CONNECT: Interface BRI0/1/0:1 is now connected to 05246848411 N/A
Sep 20 14:52:18.351: %ISDN-6-CONNECT: Interface BRI0/1/0:1 is now connected to 05246848411 cpp-poprad
Sep 20 14:52:18.531: %LINK-3-UPDOWN: Interface BRI0/1/0:1, changed state to down
Sep 20 14:52:18.531: %DIALER-6-UNBIND: Interface BR0/1/0:1 unbound from profile Di0sh isdn act

Connecting to an ISDN BRI on a router from a PSTN line from remote site..!!

Friends,
I have a 1812 at HO with WIC1 BS/T Card, connected it to an ISDN BRI line.One of my critical remote location uses Leased circuit to reach my HO Router.But in case if LL goes down,some of the important PC's at the remote site should be able to dial to HO Router BRI Number using PSTN line, get connected and continue, ip address assigned from HO Router and access the application... Is any way available...

Hi Arnab.
You need to configure dial backup through AUX port. You need to connect a normal PSTN line to a modem which in turn is connected to your AUX port. You will have to configure a chat script which you can find in the attachmnet. The attachment is a working example in one of my routers.
You also have to create an ASYNC interface. Check that in the attached file also
--Pls rate if useful---

Debugging output not appearing

I recently absorbed the task of supporting our CF MX 6.1
server. We have an app that we need to debug - the developer asked
us to add her IP address to the "Debugging IP Addresses" list. I
turned on debugging and added her IP address to the list, but
debugging output is not displaying; this is true even when you run
the CF app on the server running CF. The steps I took are as
follows:
- In CF Administrator, checked Enable Robust Exception
Information and Enable Debugging. Submitted changes and got msg
Server has been updated successfully.
- Added developer's IP address to the list of debugging IP
addresses. She couldn't see the debug output. Neither could I.
- Restarted CF server. No change.
- Rebooted server box. No change.
- Tried removing all IP addresses from list. Debugging input
then shows for everyone.
One thing of note regarding the setup of the server is that
IE has "Internet Explorer Enhanced Security Configuration" enabled
- don't know if this would have any impact. I'd also tried adding
the local IP address of my machine (I'm on the same LAN as the
server), and I got no debug info on my machine. Our whole LAN,
including the CF Server's box, is behind an ISA server, but of
course that wouldn't have any impact on the local server, and I
don't *think* it would affect machines on the LAN, but I'm not
certain of this.
Showing the debug info to everyone is not an option, so we
need to get the IP address filtering working. I've looked at the
Windows event logs, the CF logs, and these forums, and can't find
any helpful info.
Server config:
Windows Server 2003 (Standard Ed.) SP1
ColdFusion MX 6.1 (6,1,0,63958) Standard
Any suggestions would be very much appreciated.

I figured out the problem - it turns out that even our LAN
traffic goes through our ISA server, and the ISA server passes its
IP address to IIS, so CFMX is seeing all traffic as coming from the
same IP address - the LAN address of the ISA server. Adding that
turned it on for everyone, so it seems that the solution lies in
changing the config of the ISA server to pass through IP addresses.
See post by "Smiley Dave" titled "Debug IP Addresses" for a little
more info, though there's no info in that thread that he ever
actually got it working.

Stupidly easy - trace source to debug output inunit test...

I'm convinced that this is stupidly easy, but I cant figure it out...
I have a class with "TraceSource "classname" and in debugging it work fine, I see the output in the "output" window, however when running unittests I only see "debug.Write" output...
What am I missing... do I need to add a listener route or something?!
- sure I'm noJedi but that's no reason to stop trying to make stuff levitate! -
to clarify...this UnitTest:
[TestMethod()]
public void TestLogging()
System.Diagnostics.Debug.WriteLine("this is a debug writeline");
System.Diagnostics.Trace.WriteLine("this is a Trace writeline");
var ts = new System.Diagnostics.TraceSource("classname");
ts.TraceInformation("this is a ts.TraceInformation");
throw new AssertInconclusiveException();
outputs this:
Test Name: TestLogging
Test Outcome: Skipped
Result Message: Exception of type 'Microsoft.VisualStudio.TestTools.UnitTesting.AssertInconclusiveException' was thrown.
Result StandardOutput:
Debug Trace:
this is a debug writeline
this is a Trace writeline
Now... for SOME reason, THIS is NOT outputing to the DebugOutput either... when I step through the TEST...
however stepping through code NOT in unit test does put stuff in the debug output window...
What am I missing... why is the TraceSource not outputting... I can see in step through that the DefaultTraceListener is there (its the only listener) and I was under the impression that it directed output to the DebugOut output stream... is this not what
I think it is...?!

Hi Jack,
I think you are correct in that my expectations were wrong.
1) stepping through "SwitchLevel" is "Off", in the unit test, which is problematic.
turning it on (to All) starts logging, but ONLY when I manually add a CONSOLETraceListener (and set the route to debug error stream to true)
2) the doco you've pointed me at was what I was reading, but I think I read/misread it differently than you...
I think its this that threw me:
•A DefaultTraceListener emits Write and WriteLine messages to the OutputDebugString and to the Debugger.Log method. In Visual Studio, this causes the debugging messages to appear in the Output window. Fail and failed Assert messages also emit to the OutputDebugString Windows API and the Debugger.Log method, and also cause a message box to be displayed. This behavior is the default behavior for Debug and Trace messages, because DefaultTraceListener is automatically included in every Listeners collection and is the only listener automatically included.
to my thinking this means that by default a "Default -> aka Debug (when DEBUGGGING)" is created for you always, and therefore in the ABSENCE of config stuff, this would be perfect for UNITTESTING - therefore TraceSource with nothing but a name
should effectively produce the same output as "Debug.WriteLine"...
that was my thinking, but it looks like even with 'SourceLevel.All" you still need to fiddle with it...
Thanks for your input, for now, I've resolved this by adding the above stuff so that my existing TraceSources are at least outputting stuff in my tests so I can see more of what is going on without having to change my "TraceSource" calls to "Debug"
calls everywhere.
- sure I'm noJedi but that's no reason to stop trying to make stuff levitate! -

How to turn of debug output from the jdriver for Oracle

We are running our builds with Ant and doing unit-tests with junit/cactus.
The Weblogic jDriver produces what appears to be debug info on standard out which
in turn is captured by junit in xml files reporting errors etc. The problem is that
the WebLogic driver ( WL6.1 SP2) sometimes produces binary 0's ( see below) ending
up in the result xml files, and that Ant's result xml parser cannot handle - (nor
should it ).
This is probably a bug in the c-code for the jdriver , the oci dll ?
Would much appreciate how to turn off the debug(?) logging that the jDriver does:
looks like this (look for the string "[6 binary 0's]"):
Parsing: select length(SYSDATE) from dual
Executing: select length(SYSDATE) from dual
Parsing: select VALUE from V$NLS_PARAMETERS where PARAMETER='NLS_NUMERIC_CHARACTERS'
Executing: select VALUE from V$NLS_PARAMETERS where PARAMETER='NLS_NUMERIC_CHARACTERS'
Done logging in at: 60
Connection: using OCI API: OCI8[6 binary 0's]
Connection successfully established via plain JDBC
DriverManager.getDriver("jdbc:weblogic:oracle:LSS_DBSVC_DEV_autobuild")
trying driver[className=weblogic.jdbc.oci.Driver,weblogic.jdbc.oci.Driver@3383e9]
getDriver returning driver[className=weblogic.jdbc.oci.Driver,weblogic.jdbc.oci.Driver@3383e9]

Hi Gunnar,
I'd check your code for appearances of "DriverManager.setLogWriter" that set
log writer to System.out. This is the way to get driver's debug output
to standard out.
Regards,
Slava Imeshev
"Gunnar Skogen" <[email protected]> wrote in message
news:3d2972bb$[email protected]..
>
We are running our builds with Ant and doing unit-tests with junit/cactus.
The Weblogic jDriver produces what appears to be debug info on standardout which
in turn is captured by junit in xml files reporting errors etc. Theproblem is that
the WebLogic driver ( WL6.1 SP2) sometimes produces binary 0's ( seebelow) ending
up in the result xml files, and that Ant's result xml parser cannothandle - (nor
should it ).
This is probably a bug in the c-code for the jdriver , the oci dll ?
Would much appreciate how to turn off the debug(?) logging that thejDriver does:
looks like this (look for the string "[6 binary 0's]"):
Parsing: select length(SYSDATE) from dual
Executing: select length(SYSDATE) from dual
Parsing: select VALUE from V$NLS_PARAMETERS wherePARAMETER='NLS_NUMERIC_CHARACTERS'
Executing: select VALUE from V$NLS_PARAMETERS wherePARAMETER='NLS_NUMERIC_CHARACTERS'
Done logging in at: 60
Connection: using OCI API: OCI8[6 binary 0's]
Connection successfully established via plain JDBC
DriverManager.getDriver("jdbc:weblogic:oracle:LSS_DBSVC_DEV_autobuild")
tryingdriver[className=weblogic.jdbc.oci.Driver,weblogic.jdbc.oci.Driver@3383e9]
getDriver returningdriver[className=weblogic.jdbc.oci.Driver,weblogic.jdbc.oci.Driver@3383e9]
>
>

Filtering debug output from CUBE

Hi all
I'm trying to filter the output of the debug command "debug ccsip messages"
This is my reference
http://docwiki.cisco.com/wiki/Cisco_IOS_Voice_Troubleshooting_and_Monitoring_--_SIP_Debug_Output_Filtering_Support
This is what I've done:
---snip--
TR-47-0005.NEV#sh call filter match-list 1
outgoing called-number XXXXXXXX
debug condition match-list is set to EXACT_MATCH
TR-47-0005.NEV#term mon
TR-47-0005.NEV#sh debugging
CCSIP SPI: SIP Call Message tracing is enabled (filter is ON)
TR-47-0005.NEV#
--snip--
It still gives me full debug output. Weather I go for "incoming called-number", "incoming calling-number", "outgoing called-number", "outgoing calling-number" or if I set the debug condition to "partial_match".
Why is that?
CUBE: 3945G
IOS: c3900-universalk9-mz.SPA.152-4.M1.bin
/Tony

I have same problem, but only explanation I can find for this behavior is this:
"Some debug output generated during a call may not have GUID information. These debugs, represented by /xxxxxxxxxxxx/ characters in the debug header, are not filtered and always appear."
From my output there are lot of calls that have no GUID, even some calls that have GUID but NOT match condition appears in debug... Some people reported that they managed to work with diferent IOS, but for me it never worked on 3-4 versions of firmware.
For me, best alternative for filtering is to use http://translatorx.cisco.com/
Veselin

Keyboard Manager (under Windows XP) spamming System Debug Output

When running Windows XP, the Boot Camp keyboard manager (kbdmgr.exe) spams the system debug output every 500 ms with a message like "0.620690".
This is inconvenient for a developer. Often I need to check out debug output in order to accomplish some task. But as soon as I start a Debug viewer application it gets flooded with that kbdmgr messages. That is more an annoyance than a problem.
Is there a way to tell Keyboard Manager to start and remain silent?

Yes, running the 2.1 drivers. KbdMgr.exe says it is 2.0.2.44 (exe version/build number) and Boot Camp systray app says it is 2.1 Build 210A12. Took another screenshot showing these version numbers:
http://picasaweb.google.com/rholdorf/BootCamp/photo#5219317221537472034
Yes, you are right. I am filtering out those messages. The sad side is that I have to do that once each boot. And I did that so many times that I got really annoyed.

Coldfusion MX 8 Debug Output

I installed the CFMX 8 Dev Edition, enabled the debug output,
but the output is not displayed. I can access the web pages, but
can not see the debuh output.
Any ideas on how to fix this?

Jonathon,
Try removing all of the Debugging IP Addresses
Ken Ford
Adobe Community Expert - Dreamweaver
Fordwebs, LLC
http://www.fordwebs.com
"JonathanFLKeys" <[email protected]> wrote
in message
news:fmocnl$83d$[email protected]..
> I'm having the same problem - the debug text just
doesn't show up. i've
> tried
> putting 127.0.0.1 in obviously, as well as no IP, and
the static IP of
> this PC.
> I've been using CF since 4.0, so it's not like i haven't
done this a
> billion
> times. i'm not excited about reinstalling CF8 to fix it.
It's working
> correctly
> on another public webserver of ours. we haven't
installed a SP to CF8 (is
> one
> available yet?)
>
> any ideas on a work-around?
>
>
> thanks
> Jonathan
>

No debug output displayed on 3745 while SSH or Telnet

IOS 12.3(4)T4 on 3745.
While Telnet, SSH or console into router we see no debug output even after turning Terminal monitor, we can only see the show outputs, etc. While consoled into the 3745 we see nothing there is No prompt or any messages at all.
We tried replacing the console cable and placed it on different PCs or laptop still no go. I was thinking of reloading the router tomorrow night, but want to check if anyone has come across this problem. It was all working in the past without any changes.
Is there like a command i need to add, etc. But i am 100% sure its all good on the 3745.
Cheers!
-Yavuz

Try 'logging console'
'sh logg' will show what is currently being logged, look for this line to see what is being logged to the console:
Console logging: level debugging, 49 messages logged, xml disabled, filtering disabled
Hope this helps

ISDN BRI - debug output

Similar Messages

Maybe you are looking for