ISDN dialer watch feature with

Hi Friends,
Iam running bgp as PE-CE routing protocol with MPLS service provider. we use ISDN for backup, I want to know is dialer watch feature supported with bgp.
regards
ravi

According to the documentation, the dialer watch feature for dial backup is only applicable for EIGRP and IGRP.
The dialerwatch list needs to have an exact match on the route watched and needs to present at the time dialer watch is initialized.
See also:
http://www.cisco.com/warp/public/471/backup_cookbook.html#ts_watch
http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/12cgcr/dial_c/dcdbakdw.htm

Similar Messages

Dialer Watch failure

All, I have numerous international sites with leased connections that are backed up via ISDN using Dialer Watch. I have noticed that after about a year, the dialer watch stops working. I have performed a "Debug ISDN Events" and cleared the IP route which should trigger the dialer watch, and nothing happens even though the route is not present in the routing table. It almost sounds like there is some kind of memory leak associated with ISDN processes. If I perform a test call or reboot the router everything starts working again. I have noticed this 3 times on 3 seperate platforms; 2600, 2811, and 3640. I am also using various IOS's on each. I scoured Cisco's website and found nothing. Has any experienced anything like this?

Verify that the DDR connection is working properly before you configure dialer watch. Verify there are two dialer map statements on the backup interface.
http://www.cisco.com/en/US/tech/tk801/tk379/technologies_configuration_example09186a0080094143.shtml#troubleshootingdialerwatch

I have the iphone4. I enter an appointment and utilize the alert feature with that appointment. the next day, approximately, the alert that I set up is gone. Is this an issue that anyone is having while backup to the cloud? or is there a switch or somet

I have the iphone 3gs. I enter a calendar appointment and utilize the alert feature with that appointment. the next day the appointment is still there but the alert is no longer there. is this an issue because I back up to the icloud or is there a switch that I need to turn on or off?
thanks, David

I have exactly the same concern. It seems it would be a simple fix for Apple to allow users to turn off the camera (and even the mic) while keeping FaceTime open -- especially now that it turns out FaceTime must remain open in order to send and receive iPhone calls on a Mac.
I like to think this new functionality of FaceTime will be baked into a future release of Yosemite, as the current setup has that not-quite-finished feel of a work in progress. In the meantime, there's nothing like a little piece of Post-It stuck over the camera to keep the NSA from watching your face as you type a post to the Apple Support Communities.

Dialer Watch List on Pri dialer????????

Dear All,
I have a 2811 router...
In which I want to configure the dialer watch list..
Plz clarify which ip shud we put on dialer watch list...????
Is it the route . plz find the example below..
boot-start-marker
boot system flash c2800nm-entbase-mz.123-8.T11.bin
boot-end-marker
controller E1 1/0
framing NO-CRC4
pri-group timeslots 1-31
interface Serial0/2/0
description
ip address 139.158.79.89 255.255.255.252
encapsulation ppp
fair-queue
interface Serial1/0:15
no ip address
ip accounting output-packets
encapsulation ppp
dialer pool-member 10 max-link 2
dialer pool-member 20 max-link 2
isdn switch-type primary-net5
ppp multilink
interface Dialer1
description
ip address 139.158.79.93 255.255.255.252
encapsulation ppp
dialer pool 20
dialer idle-timeout 2147483
dialer string 08041259117
dialer load-threshold 1 either
dialer watch-group 10
dialer-group 1
no fair-queue
ppp multilink
interface Dialer10
description
ip address 139.158.79.85 255.255.255.252
encapsulation ppp
dialer pool 10
dialer idle-timeout 2147483
dialer string 02240057435
dialer load-threshold 1 either
dialer-group 1
fair-queue 64 32 0
ppp multilink
ip route 10.179.27.0 255.255.255.0 139.158.79.90
ip route 10.179.27.0 255.255.255.0 Dialer1 100
ip http server
dialer-list 1 protocol ip permit
Plz give me the solution for the back up for the serial link...using the dialer watch list..
Thanks...

configuring dialer-watch
~~~~~~~~~~~~~~~~~~~~~
1) check the ip routing table for the particular route for which you have to create a dialer watch and note it down as it is.
2) create a watch list using the command # Dialer watch-list ip < exact mask>
3) go to the dialer interface and bind it using the command # dialer watch-group
4) Bind it to the interface
For more information regarding the configuration of dialer watch follow the url given below ,
http://www.cisco.com/en/US/products/sw/iosswrel/ps1828/products_configuration_guide_chapter09186a00800872ed.html#18075
4)

I have dsl internet service with a download speed of .66 mbps. I would like to watch netflix with a wireless conection to apple tv. What is the required internet speed?

I have a dsl internet conection with a download speed of .66 mbps. I would like to watch netflix with a wireless conection to apple tv. What is the required internet speed?

Welcome to the Apple Community.
Netflix recommend a minimum connection speed of 0.5 Mbps, however at that speed many of the other features of the Apple TV will be painfully slow.

Regarding: Enabling 11gR2 File watcher feature in 10gR2.

Hi,
We need to have 11gr2 File_watcher feature in 10.2.0.1 in Windows XP.
We ran the dbms_scheduler script in 10gR2 database available in ORACLE_HOME/rdbms/admin/dbmssch.sql of 11gR2.
Since this feature is available in 11gR2.
we tried to execute the script in 10gR2, we are getting the following error.
ERROR at line 1:
ORA-04063: package body "SYS.DBMS_SCHEDULER" has errors
ORA-06508: PL/SQL: could not find program unit being called:
"SYS.DBMS_SCHEDULER"
ORA-06512: at line 2
Is there any package/scripts/Procedures to enable the file_watcher feature in 10.2.0.1 database.
Please help me in this regards,
Thanks
Kumaresh.

The new File Watcher feature is really nothing more than a job that wakes up every ten minutes to check for the existence of file(s).
There is nothing to stop you writing your own PL/SQL that checks for a file using either UTL_FILE or DBMS_LOB and scheduling that every 10 minutes with either DBMS_JOB or DBMS_SCHEDULER. You could, if you wanted, write your PL/SQL so that it puts a message in a queue when it finds a file, or even start a scheduler job. Or anything you like.
Nothing to stop you at all.

Dialer watch over Ethernet

I want to use DSL for backup of my MPLS network. I plan to use an external ethernet connected device for DSL access. I plan to use a GRE tunnel over the DSL connection. Can I use dialer watch to bring up the tunnel interface?

I do not know the answer for sure, but I believe that Dialer Watch will not work for the Ethernet/DSL connection. And I wonder why the original post believes that they want it. The motivation for dialer watch is for traditional dial environments where you pay connect time charges and do not want to pay for connectivity when the primary link is available. But with DSL you are not paying connect time charges. You pay the same whether the DSL is actively carrying traffic or not. So why would you want to try to keep the Ethernet or the GRE down while the MPLS was up?
It seems to me that what is needed here is a reliable fail-over mechanism so that traffic is sent over the MPLS when it is available and is sent over the Ethernet/DSL/GRE when MPLS is not available. Without knowing a little more about the environment it is hard to suggest an optimum solution. But I have implemented something that seems a bit similar where DSL/GRE was a backup connection. We ran a dynamic routing protocol over the primary link and over the backup DSL/GRE and configured it so that the protocol preferred the main link and would use the DSL/GRE only when it lost the neighbor relationship on the primary link. It seems like the same approach should work here.
HTH
Rick

Is there a problem if I use dialer watch without dialer-group?

I use isdn as back up intface,and use dialer watch to monitor.
my configuration is :
interface BRI0/0
description ***To 11.228.244.1***
ip address 11.228.244.2 255.255.255.128
encapsulation ppp
no ip route-cache
no ip mroute-cache
dialer map ip 11.228.244.1 name C-3640-01 broadcast 02080000759
dialer map ip 11.228.8.62 name C-3640-01 broadcast 02080000759
dialer watch-disable 10
dialer watch-group 1
isdn switch-type basic-net3
no peer neighbor-route
no cdp enable
ppp authentication chap
dialer load-threshold 128 either
ppp multilink
dialer watch-list 1 ip 11.228.8.62 255.255.255.255
dialer watch-list 1 ip 11.228.8.61 255.255.255.255
dialer watch-list 1 delay disconnect 10
As you can see,no "dialer-group" command in my configuration.
When I shut down the primary interface,my isdn dialer up correctly,and learn the route from bri0/0.When my primary interface up again,my isdn interface disconnect as expected.
All seems good,so is the "dialer-group" needed in the configuration of dialer watch ?

Hello,
that is actually the default behaviour of dialer watch, it does not depend solely on interesting traffic to trigger the backup. As soon as the primary link goes down, dialer watch brings up the secondary link.
Check the explanation on CCO regarding dialer watch:
Dialer Watch Overview
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fdial_c/fnsprt6/dcdbakdw.htm#wp1000889
HTH,
GP

Multiple entries in dialer watch-list

Hi,
If I have multiple entries in my dialer watch-list:
dialer watch-list 1 ip 192.168.10.3 255.255.255.255
dialer watch-list 1 ip 192.168.20.3 255.255.255.255
And just one of the routes gets removed (for example 192.168.10.3) - will this trigger my router to dial the backup link? OR Do both the routes have to be removed before the router will dial?
(Just a little background - the host routes I'm watching are loopback interfaces of head-end MPLS routers and I'd only like the remote router with the dialer watch-list to dial if BOTH loopbacks are removed from the routing table)
Thanks!
Brad

Brad
In my limited experience with dialer watch, I believe that you are going to get the results that you want. Dialer Watch will initiate the backup when all of the specified routes are removed from the routing table.
HTH
Rick

WCCP and ISDN / Dialer

We have two routers running the same IOS version in our core - c7200-is-mz.123-10a.bin. One terminates a number of tunnels and the other has a number of dialer interfaces associated with an ISDN PRI. Each of our site routers has a tunnel going to the core (via an ADSL connection) and a backup ISDN interface with a dialer configured. When we are running on the primary links everything works fine. When we are running on the backup links (the ISDN) WCCP redirection seems to prevent clients from accessing services on TCP in the core (I can telnet to the core ISDN router from a PC on site, but can't access anything else). Ping always works fine - hence my suspicions about WCCP. If I disable WCCP on the core router with the ISDN links backup connections work fine.
Our remote routers use c2800nm-advsecurityk9-mz.124-11.T4.bin.
My question is - is there any issue with WCCP redirection and dialer interfaces?
Below is the relevant config for the routers that don't work (addresses, names and numbers have been sanitized.
corerouter#
ip wccp 61
ip wccp 62
interface Dialer183
description Backup DoD for remote site
bandwidth 64
ip address 192.168.1.1 255.255.255.252
ip wccp 61 redirect out
ip wccp 62 redirect in
encapsulation ppp
dialer pool 2
dialer remote-name siterouter
dialer idle-timeout 300
dialer enable-timeout 60
dialer wait-for-carrier-time 10
dialer caller 222222
dialer-group 1
snmp ifindex persist
ppp authentication chap
End
siterouter#sh run
ip wccp 61
ip wccp 62
interface Dialer1
description Backup DoD to the core via ISDN
bandwidth 64
ip address 192.168.1.2 255.255.255.252
ip wccp 62 redirect in
encapsulation ppp
dialer pool 2
dialer remote-name corerouter
dialer idle-timeout 300
dialer enable-timeout 60
dialer wait-for-carrier-time 10
dialer string 111111
dialer caller 222222
dialer-group 2
ppp authentication chap
end

Zach,
I've tried that as you suggested and it made no difference. I had seen a bug on the bugtracker about process switched packets possibly not being WCCP redirected correctly, so I have also tried ensuring that CEF was enabled, and removing compression in case that made the packets process switch.
I have also tried removing the multilink and ensuring that only one ISDN B channel is pulled up for that dialer interface. That made no difference.
I have verified that it is the router in the core that is causing the issue because I can have the remote site connect to the core via ISDN and have WAAS optimise traffic from that remote site to another remote site via the core (if I disable WCCP in the core).
Thanks,
Peter

HT201667 I rented a movie through itunes on my ipad and wanted to watch it with friends on a digital projector, but it wouldn't allow me to do it. Is there any way around this?

I rented a movie through itunes on my ipad and wanted to watch it with friends on a digital projector, but it wouldn't allow me to do it. Is there any way around this?

The issue was that a dialogue box came up which said that I couldn't play this movie on another device. I tried playing the same movie on an Tv with an HDMI connection attached to an adapter to the IPad and that worked. I wonder if the problem is that the digital projector has a VGA connection.

I have a late 2011 model MacBook Pro running Mountain Lion. I love the AirPlay mirroring feature with Apple TV...BUT, how do I mirror with TVs that don't have Apple TV? I used to run a cable from my mini display port to the HDMI input of a TV.

I have a late 2011 model MacBook Pro running Mountain Lion. I love the AirPlay mirroring feature with Apple TV...BUT, how do I mirror with TVs that don't have Apple TV? I used to run a cable from my mini display port to the HDMI input of a TV. This feature seems to be lost in the Mountain Lion upgrade. Did Apple feel that once Mountain Lion came out that EVERYONE would have Apple TV? There are no settings in System Preferences/Display like there used to be...only for AirPlay Mirroring.

Running a cable to the HDMI port is still supported. (and still works on mine).
If the Arrangement tab in System Preferences > Displays isn't present then it doesn't recognize the physical connection. Double check all cables. If that doesn't work try a PRAM reset:
http://support.apple.com/kb/ht1379

Im not satasfied with 6.0 i miss youtube and some apps are slower, facebook wants premission to access my contacts, and how do i use apple tv feature with out mirroring?

Im not satasfied with 6.0, i miss youtube, some apps are slower, facebook wants premission to access my contacts, and how do i use apple tv feature with out mirroring?

That is awesome, works perfectly.
I'll get it worked into my main script. Is this Action Manager code, and not just regular Javascript from the Scripting Dictionary? I can't tell the difference. I'll see whether or not it's actually faster than Applescript.
Thanks. I know Scripting Listener records a bunch of stuff, but it's pretty amazing to me that playing back this line does the same thing that playing back the 1,011 lines Scripting Listener puts out.
Thanks.

Error occurred in deployment step 'Add Solution': A feature with ID '' has already been installed in this farm. Use the force attribute to explicitly re-install the feature.

Hi I am getting the error
Error occurred in deployment step 'Add Solution': A feature with ID 10495515-2482-41fd-98eb-3c87f739f54b has already been installed in this farm. Use the force attribute to explicitly re-install the feature.
when trying to deploy web parts
question 1 - how do i use the force attribute when deploying from visual studio
question 2 - am i deplying it to the right place, if i deply it to the
url:port that points to my central admin tool it deploys but i cant seem to see it in any of my webs in my site collection, if i deploy it to the
url:port that points to my site collection I get this error.
im new to all this by the way :)
thanks in advance

If you are deploying from Visual Studio then please follow this post:
http://sharepointfordeveloper.blogspot.com/2014/03/solved-visual-studio-issue-error.html
Open the visual Studio and navigate to the feature XML file and add the bellow attribute.
AlwaysForceInstall="TRUE"
The <FeatureName>.Template.Xml output would be some think link this.
<?xml
version="1.0"
encoding="utf-8"
?><Feature
xmlns="http://schemas.microsoft.com/sharepoint/"
AlwaysForceInstall="TRUE"></Feature>

Can I use watch folders with my network drive in Photoshop elements 10

Can I use watch folders with my network drive in Photoshop elements 10

photodrawken a écrit:
See the tips in this FAQ:
http://www.johnrellis.com/psedbtool/photoshop-elements-faq.htm#_Watchi ng_Network_Folders
Ken
Beware the FAQ you are referring to is no longer relevant. It does not apply to PSE10
Hereunder the warning issued by the author himself.
Photoshop Elements 6/7/8 (Windows) Frequently Asked Questions (FAQ)
John R. Ellis
Last updated January 21, 2011
Copyright 2008-10 by John R. Ellis
As of June 2010 I no longer maintain this FAQ. I’ve migrated to Lightroom 3, which I use for all my organizing and most of my editing (I still use the Photoshop Elements Editor for more involved editing). Adobe has clearly decided not to invest sufficient resources for properly maintaining the Photoshop Elements Organizer– see my Amazon review of PSE 8. Lightroom is marketed to professionals and prosumers with tens of thousands of photos who demand adequate organizational capabilities, whereas Photoshop Elements is marketed to consumers, most of whom do not want or use the Organizer.
This page captures my answers to frequent questions about Photoshop Elements 6, 7, and 8 (Windows). It’s mostly about the Organizer, since I know the Organizer much better than the Editor.
The versions to which each FAQ applies are indicated with the notation [PSE 6, 7, 8]. If I’m not sure whether something applies to a version, it will be indicated with a question mark, e.g. [PSE 7, 8?].
If you have corrections or suggestions, please email them to john at johnrellis.com.

ISDN dialer watch feature with

Similar Messages

Maybe you are looking for