ISDN PRI Configuration errors

Dears,
I trying to configure a ISDN PRI on a 1751-V router and the following error occur:
CISCO_BARR(config-controller)#pri-group time 1-6
%Controller tdm clock does not have data capability
%Insufficient HDLC resource for pri-group - it has been removed
How do I to configure ISDN PRI in that router ?
More information:
Cisco 1751-V
Router Version: c1700-ipvoice-mz.123-9d.bin

Hi,
Please make sure that you putting the T1/E1 card in the WVIC and not VIC slot as PRI can do
voice but it is still considedred as data, so if you try to confiugre this in a slot that
is VIC (instead of VWIC) only then it will not work for you. Furthermore, you needed to
have the tdm clock command set to both and not just voice, as you are creating a PRI,
which, again, is Data, but can do voice too.
here is the example of command :--
tdm clock T1 2/0 both export line
hth
CJ

Similar Messages

How to configure isdn pri on gigabit interface on AS 5850 router

hello All,
i currently have a project at hand which is a voip project using sip protocol. my client wants to send voip traffic to my router using STM interface with SIP protocol. But the challenge is how do i convert the sip protocol to ISDN PRI on another STM gigabit interface before sending it to my PSTN switch for onward termination to the customer. currently i use serial interface to communicate with my PSTN using E1 for other existing clients in other to terminate calls to customers. please see sample configuration below:
interface Serial10/1:15
no ip address
encapsulation hdlc
no snmp trap link-status
trunk-group JKN
isdn switch-type primary-net5
isdn incoming-voice modem 64
isdn map address .* plan unknown type unknown
isdn send-alerting
no cdp enable
thank you.
Adekunle

hello n-kirillov,
Yes i mean STM as Synchronous Transport Module for Optical Network. currently, the medium of transport for communication between my router and the PSTN switch is the serial interface whose configuration i have shown above. also currently E1 pri cables are connected to this serial interface and E1s are provision for this serial interfaces directly from the switch for communication with the PSTN switch.
the question now is that my switching team now wants be to communicate with their switch using fibre from STM interface on my router without using PRI cables. is this achievable? if yes what is the configuration like?

Why do we need to assign ip for the D channel ISDN-PRI

Why do we need to assign ip address to the D channel (signaling ) when we configure ISDN-PRI in the example below :
http://www.cisco.com/univercd/cc/td/doc/product/access/ap/ap_ts3/ap_ts3sw/apswisd.htm
<quote>
Step 1:Specify the D channel of the first Primary Rate Interface (PRI):
AS01(config)# interface Serial 0:23
AS01(config-if)#
Step 2: Assign an IP address and subnet mask to the interface:
AS01(config-if)# ip address 172.16.254.253
</quote>
Regards

You can assing one there, and / or on dialer interfaces. It depends on what you are doing.
These will be the address used by PPP when it runs on the B-channels.

Reserving Timeslots on a ISDN PRI

Hi,
Can it be configured on the ISDN PRI link of the Central Location Data Center, reserving 10 Timeslots for taking the calls from one particular Branch Location and another 10 from another individual branch and remaining 10 from left over Branch Sites.
Can we use the channel-group command for this type of the configuration.
Can the 15th timeslot (for e.g., Serial 2/0:15) used when reserving the timeslots under the channel-group command.
Request anyone help me finding a solution.
Regards,
Keshava Raju
[email protected]

You cannot partition the PRI and if you want to limit calls, it's particularly complicated because what you want to do, is to not answer or reject calls when the group a branch pertains to, is full.
In my knowledge, this is not possible. You can hack something with radius to do that authentication is denied when group is full, but this is not the same as not taking the calls.
Hope this helps, please rate post if it does!

Remote dialin access using isdn pri

I configured dialin accesss using isdn pri interface. It works fine just for one user. When another user dials in (using same or different local username/password), the previous one loses the connectivity. Actually the statuses seem fine for the previous user: I can see him under "sh users" as well as host route in routing table. ppp session stays idle. There is no ip connectivity anymore.
aaa authentication ppp default local
isdn switch-type primary-net5
username test1 password 7 03105E18125E
username test2 password 7 06120A32581C
controller E1 1/0
pri-group timeslots 1-31
controller E1 1/1
pri-group timeslots 1-31
interface Serial1/0:15
no ip address
dialer pool-member 1
dialer idle-timeout 7200
isdn switch-type primary-net5
interface Serial1/1:15
no ip address
dialer pool-member 1
dialer idle-timeout 7200
isdn switch-type primary-net5
interface Dialer0
ip unnumbered FastEthernet0/0.1
encapsulation ppp
dialer pool 1
dialer caller "XYZ"
dialer-group 1
peer default ip address pool netm
fair-queue
ppp authentication chap pap
ip local pool netm 10.31.32.65 10.31.32.126

Hi Starman,
configure the following command under dialer inetrafce and check the issue.
int di0
dialer load-threshold 255 either
dialer ilde-timeout 120
if you want another to use the isdn line then create another dialer interface.
clarify me whether the users are accessing the pri from the same location or different locations using different isdn no's.
If users are present in two different locations then best solution is create seperate dialer interface for users.
Thanks,
Satish

No carrier from PVDM2-36DM via ISDN PRI link

The network topology is
Modem --> [FXS][cisco 2821][E1] --> ISDN PRI --> [E1][cisco 2811][PVDM2-36DM]
ISDN PRI link is operated correctly, debug isdn q931 shows that connection is established. Info message is
*Jul 23 06:27:45.407: %ISDN-6-CONNECT: Interface Serial1/0:1 is now connected to 555 N/A
Unfortunately, no carrier signal is going from modem to line.
Configuration of Cisco Routers is below.
1st (2821)
==========
controller E1 0/2/0
framing NO-CRC4
pri-group timeslots 1-2,16
interface Serial0/2/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-qsig
isdn incoming-voice modem
no cdp enable
dial-peer voice 1 pots
destination-pattern 555
port 0/3/0
voice-port 0/3/0
cptone RU
dial-peer voice 888 pots
destination-pattern .T
port 0/2/0:15
2nd (2811)
==========
controller E1 1/0
framing NO-CRC4
pri-group timeslots 1-2,16
interface Serial1/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-qsig
isdn timer T310 120000
isdn not-end-to-end 64
isdn protocol-emulate network
isdn incoming-voice modem
no cdp enable
line 0/322 0/357
modem InOut

> The PVDM2-DM works only with NM-xT1/E1.
Yes, of course, it is well known fact. We are using NM-1CE1T1-PRI. See "show diag" output below.
Slot 0:
C2811 Motherboard with 2FE and integrated VPN Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
PCB Serial Number : FOC11070F5L
Hardware Revision : 1.0
Top Assy. Part Number : 800-26920-03
Board Revision : A0
Deviation Number : 0
Fab Version : 03
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 87
Hardware date code : 20070214
Chassis Serial Number : FHK1109U00A
Chassis MAC Address : 001b.2aa3.c1c8
MAC Address block size : 24
CLEI Code : COM7C00ARA
Product (FRU) Number : CISCO2811
Part Number : 73-10258-04
Version Identifier : V04
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF C1 8B 46 4F 43 31 31 30 37 30 46 35 4C 40
0x10: 03 E7 41 01 00 C0 46 03 20 00 69 28 03 42 41 30
0x20: 88 00 00 00 00 02 03 03 00 81 00 00 00 00 04 00
0x30: 09 87 83 01 32 3F 46 C2 8B 46 48 4B 31 31 30 39
0x40: 55 30 30 41 C3 06 00 1B 2A A3 C1 C8 43 00 18 C6
0x50: 8A 43 4F 4D 37 43 30 30 41 52 41 CB 8F 43 49 53
0x60: 43 4F 32 38 31 31 20 20 20 20 20 20 82 49 28 12
0x70: 04 89 56 30 34 20 D9 02 40 C1 FF FF FF FF FF FF
PVDM Slot 0:
36 port PVDMII digital modem PVDM daughter card
Hardware Revision : 1.0
Part Number : 73-10102-03
Board Revision : C0
Deviation Number : 0
Fab Version : 03
PCB Serial Number : FOC10354YRW
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 00
Product (FRU) Number : PVDM2-36DM
Version Identifier : V01
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 04 90 41 01 00 82 49 27 76 03 42 43 30
0x10: 88 00 00 00 00 02 03 C1 8B 46 4F 43 31 30 33 35
0x20: 34 59 52 57 03 00 81 00 00 00 00 04 00 09 00 CB
0x30: 8A 50 56 44 4D 32 2D 33 36 44 4D 89 56 30 31 20
0x40: D9 02 40 C1 FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Slot 1:
NM-1CE1T1_PRI Port adapter, 1 port
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 1.0
Top Assy. Part Number : 800-21550-02
Board Revision : A0
Deviation Number : 0-0
Fab Version : 03
PCB Serial Number : FOC104753CA
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Fab Part Number : 28-5935-03
Manufacturing Test Data : 00 00 00 00 00 00 00 00
Field Diagnostics Data : 00 00 00 00 00 00 00 00
Product (FRU) Number : NM-1CE1T1-PRI
Version Identifier : V01
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 03 9D 41 01 00 C0 46 03 20 00 54 2E 02
0x10: 42 41 30 80 00 00 00 00 02 03 C1 8B 46 4F 43 31
0x20: 30 34 37 35 33 43 41 03 00 81 00 00 00 00 04 00
0x30: 85 1C 17 2F 03 C4 08 00 00 00 00 00 00 00 00 C5
0x40: 08 00 00 00 00 00 00 00 00 CB 8D 4E 4D 2D 31 43
0x50: 45 31 54 31 2D 50 52 49 89 56 30 31 20 FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Cisco 3845, h323-isdn pri, reverese caller id

Hello!
I run mixed voip network, with several h323-isdn pri gateways.
Some of these gateways are cisco, some asterisk.
I configured one of asterisk gateways according to
http://www.voip-info.org/wiki/view/Asterisk+func+CONNECTEDLINE
so if I do call in following scheme:
PBX1--pri--asterisk1--h323--asterisk2--pri--PBX2
once PBX1 user accept call user on PBX receives user's name from PBX1.
but if I do call in
PBX1--pri--asterisk1--h323--cisco3845--pri--PBX2
There is no user name.
Asterisk sends name as informational element, I see it in traffic dump.
What I need to configure on cisco , so it will transfer this element to PBX2?
Thank you!

There doesn't seem to be a happy intersection between using MGCP to get access to caller name and SRST mode.
According to http://www.ciscotaccc.com/kaidara-advisor/voice/showcase?case=K32431525
Media Gateway Control Protocol (MGCP) PRI backhaul does not support call preservation when transitioned from MGCP to Survivable Remote Site Telephony (SRST) or from SRST to MGCP."
Which is bad, because you don't want calls dropping in and out if the WAN link is bouncing. The solution according to the case is "Use H.323", but of course the issue there is that you lose the display name if it's in the facility and not the display field.
It would be nice if it could at least be "lazy", so that the router would either wait until there was no call activity, or at least schedulable / forceable so that you can control what's happening.

Pri hdd error

I'm putting the next things together:
MSI 865PE NEO2 PFISR, 3,0 gHZ P4, MATROX P650, WD 360 SATA RAPTOR, PLEXTOR 116 DVD, KINGSTON PC3700 HYPERX 2x512Gb, Antec 3700BQE.
When booting there is an error: pri hdd error. Replaced the sata cable and tried the sata2, no result.
When I push f1(resume) windows starts setup but quits because it needs a hard drive...
What should I do?

Which version of Windows?
Are you booting from the CD and installing Windows and where does it stop. Blue screen where it says there are no drives to install to?
Also what settings do you hav in Bios>>Integrated Peripherals>>On-Chip IDE Config.
If using XP should be:
Native Mode
SATA Only
Keep PATA active-Yes
Both Channels
Configure as Raid-No
Leave rest at default

ISDN PRI & BRI configration

Hi,
I have 2800 series route at central location with PRI line and remote location with BRI line and DLINK router. i have 10 remote site.
Now i want to connect my multiple remote site through BRI to my PRI at central location
can you guide me with the configration at the central location PRI part
I am in INDIA
Bhargav

in india we have E1 as a PRI follow the procedure.
Configuring Channelized E1 ISDN PRI
To configure ISDN PRI on a channelized E1 controller, use the following commands beginning in global configuration mode:
Command Purpose
Step 1
isdn switch-type switch-type
Selects a service provider switch type that accommodates PRI. (Refer to Table 17 for a list of supported switch type keywords.)
Step 2
controller e1 slot/port
or
controller e1 number
Defines the controller location in the Cisco 7200 or Cisco 7500 series router by slot and port number.
Defines the controller location in the Cisco 4000 series or the Cisco AS5200 universal access server by unit number.1
Step 3
framing crc4
Defines the framing characteristics as cyclic redundancy check 4 (CRC4).
Step 4
linecode hdb3
Defines the line code as high-density bipolar 3 (HDB3).
Step 5
pri-group [timeslots range]
Configures ISDN PRI.
.1 Controller numbers range 0 through 2 on the Cisco 4000 series and 1 to 2 on the Cisco AS5200 access server.
If you do not specify the time slots, the specified controller is configured for 30 B channels and 1 D channel. The B channel numbers range 1 to 31; channel 16 is the D channel for E1. Corresponding serial interfaces numbers range 0 to 30. In commands, the D channel is interface serial controller-number:15. For example, interface serial 0:15.
Table 17lists the keywords for the supported service provider switch types to be used in Step 1 above.
Dlink you have to configure simple dial-up connectivity with PRI.
Thanks,
Dharmesh Purohit

ISDN PRI dialer connections to AS5300

Swapping out an AS5200 running 11.3 with an AS5300 running 12.3. Copied the same config from the 5200 to the 5300. ISDN Pri calls from remote routers to the 5200 connect and stay connected. Calls from the same router to the 5300 disconnect after 1 sec. Q931 debug shows x8090 disconnect code being sent from the 5300. Suspect AAA auth issue because I don't see any attempts logged in tacacs server (CiscoSecure). When I debug ppp auth the only thing out of the ordinary is a "PPP Authorization Required" message but the AAA author configs are the same on both 5200 and 5300. When I run a debug on tacacs on the 5300 I see "pass" statuses coming back from the server.

Use below commands to troubleshoot.
â¢ debug isdn q931 - To check ISDN connections as outbound calls are initiated.
â¢ debug ppp negotiation - To see if a client is passing PPP negotiation. A high number of concurrent PPP negotiations can overwhelm the router CPU.
â¢ debug ppp authentication - To see if a client is passing authentication. If you are using a version prior to Cisco IOS release 11.2, use the debug ppp chap command instead.
â¢ debug ppp error - To display protocol errors and error statistics associated with PPP connection negotiation and operation.

ISDN PRI redundancy on AS5300

I am having cisco AS5300 router with a ISDN PRI line terminating over it.
I would like to have redundancy for the existing PRI line with another PRI.
Is this possible ? If yes where can I get a sample configurations.

If it's redundancy for the dialin, you have two options:
1) Make all the clients add the secondary number to dial
2) Request a single number for the two ISDN PRI's from your telco (this is without a doubt the easiest).
If it's redundancy for dialout, just add the interface in the same dialer pool as the first one...:
interface Serial0:15
dialer pool-member 1
interface Serial1:15
dialer pool-member 1
Did it help?

How do I fix a Configuration Error on MacBook Pro?

I have a MacBook Pro 2.4 GHz Intel Core i5 with 8 gigs of memory. I was running CS6 and my video board went out. I got it fixed but lost all my data on my hard drive. So I tried installing cs6 from a disk image that I had saved and after entering the serial code I received that my license was revoked. That could be true since I was at another company when I purchased it. Now I'm trying out the TRIAL Adobe cloud solution and after installing and getting updates, when i clicked on the app I get a configuration error when trying to open the . Do I need to delete some library items that are conflicting when I tried to install CS6?
Here is the error:
A problem has occured with the licensing of this product. Restart your computer and re-launch the product.
If this problem still occurs after restarting, contact Customer Support for further assistance, and mention the error code shown at the bottom of this screen.
Error: 213:5

Imjoewalkerid the file permissions on your SLStore folder have become compromised. Please see Configuration error 16 | CC, CS for information on how to resolve Error 213:5.

Configuration Error 213:19 Adobe PhotoShop CC when sequenced using Microsoft App-V 5.0

Does anyone out there have a Microsoft App-V 5.0 recipe for Adobe PhotoShop CC ?
When I run the App-V package, I get the License Configuration Error 213:19
Thank You. very much for your time. Karl

You will probably get better help in Photoshop General Discussion
The Cloud forum is not about using individual programs
The Cloud forum is about the Cloud as a delivery & install process
If you will start at the Forums Index https://forums.adobe.com/welcome
You will be able to select a forum for the specific Adobe product(s) you use
Click the "down arrow" symbol on the right (where it says All communities) to open the drop down list and scroll

Configuration error when open admin tool in BIEE 11g client

Hi All,
I have installed BIEE 11g client in my laptop,the version is 11.1.6.2 ,it has show one error in the installation log :
<action name="Custom Action" target="oracle.bi.CustomIAActionGetInstanceNumber" status="error">
- <AdditionalNotes>
<error>class oracle.bi.CustomIAActionGetInstanceNumber.install() runtime exception:</error>
</AdditionalNotes>
After installation,when I try to open the admin tool in start menu,it show configuration error , but I can open the admin tool through installation directory.
And when I try to import metadata,it also shows connection has failed.
Can any body give some helps on this,thanks a lot.
Ryan.
Edited by: 997662 on Apr 5, 2013 1:39 AM

Hi,
Let me know which version you are using (OBIEE) ?
you are trying to install Client (Admin Tool) and OBIEE server in same machine ?
Thx,

The report server has encountered a configuration error. Logon failed for the unattended execution account. (rsServerConfigurationError) Log on failed. Ensure the user name and password are correct. (rsLogonFailed) Logon failure: unknown user name or bad

The report server has encountered a configuration error. Logon failed for the unattended execution account. (rsServerConfigurationError)
Log on failed. Ensure the user name and password are correct. (rsLogonFailed)
Logon failure: unknown user name or bad password
am using Windows integrated security,version of my sql server 2008R2
I have go throgh the different articuls, they have given different answers,
So any one give me the exact soluction for this problem,
Using service account then i will get the soluction or what?
pls help me out it is urgent based.
Regards
Thanks!

Hi Ychinnari,
I have tested on my local environment and can reproduce the issue, as
Vaishu00547 mentioned that the issue can be caused by the Execution Account you have configured in the Reporting Services Configuration Manager is not correct, Please update the Username and Password and restart the reporting services.
Please also find more details information about when to use the execution account, if possible,please also not specify this account:
This account is used under special circumstances when other sources of credentials are not available:
When the report server connects to a data source that does not require credentials. Examples of data sources that might not require credentials include XML documents and some client-side database applications.
When the report server connects to another server to retrieve external image files or other resources that are referenced in a report.
Execution Account (SSRS Native Mode)
If you still have any problem, please feel free to ask.
Regards
Vicky Liu
Vicky Liu
TechNet Community Support

ISDN PRI Configuration errors

Similar Messages

Maybe you are looking for