ISE backup not working while using tftp

I have configured a repository on ISE admin node to use tftp for taking backups.
repository master
url tftp://<IP>
I initiate backup on demand to use the defined repository and specify Application-only backup. After sometime, I see success on ISE node and "show backup history" also shows success
ise/admin# sh backup history
Thu Sep 27 06:12:43 UTC 2012: backup backup1-120927-060253.tar.gpg to repository master: success
Thu Sep 27 07:31:56 UTC 2012: backup backup1-120927-072227.tar.gpg to repository master: success
However, when I check on tftp server, I see nothing. No files with names backup1-120927-060253.tar.gpg or backup1-120927-072227.tar.gpg...Has anybody else seen similar issue? Is there a bug with tftp server backup on ISE nodes?
Thanks,
Kashish

Kashish,
Can you try moving a small file over to the tftp server? Check the directory of the local disk and issue a a copy disk:/file tftp:/path.
See if that moves a file over. I havent personally used tftp I always use ftp.
Thanks,
Tarik Admani
*Please rate helpful posts*

Similar Messages

Microphone not working while using handset

microphone not working while using handset
But it is working when loud speaker is On
Y
Wat to do??
Kindly revert with your comments

Repair the phone with PCC and report back PC Companion (PCC) Bridge (for Mac) Alternatives on How to backup Xperias http://talk.sonymobile.com/thread/36355

My autofill does not work while using Safari. Have checked both Safari and Apple settings.

My Autofill does not work while using Safari. I have checked both my Safari settings and my Apple settings but don't know what else to do.

Hi Eustace....yes, I did reset Safari but it didn't help. I'm running Mac OS X Lion 10.7.5...which might be the problem...my Safari is Version 6.1.1.

Messages not working while using Internet sharing from my iMac ... Any troubleshooting tips/approaches ?

I am connecting to the internet using the Internet Sharing from my iMac ...
The trouble is the messages in the Messages app are not sent when I am connected through my iMac ... When I key in a message and hit send a progress bar appears fills up till 90% and just gets stuck there and after a while the red exclamation mark stating the message was not sent appears ... Now if I connect through my wi-fi router or thether through my phone it works fine ... I can send / recieve messages ...
Similar points to note - Today when I tried to make an App Purchase - The security info screen ( new additon - http://isource.com/2012/04/11/iphone-app-store-security-info-alert/ ) popped up but I got a blank screen for the securtiy questions screen ... It was not loading the screen ... Some games the game center invite does not work through my Internet sharing (tried in MetalStorm) ... but works fine thorough wi-fi or thether ...
What could be the problem with my iMac s sharing? Any suggestions would be really useful /// Thanx in advance
I am running Lion ... and I have updated to the latest Airport software ...
Only thing I tried was changing the DNS ... but that s not related right ?

Powerline adapters use your home powerlines (mains a/c) to connect your devices via ethernet to your modem, they're easy to set up and the they TOTALLY fixed my ATV problem, the problem seems to be with the wireless. I've been trawling through apple discussions, and did found a workaround to my problem https://discussions.apple.com/thread/4222883?start=0&tstart=0
but its just a workaround :/

On call sound volume is not working while using ha...

The volume control does not work on call while using hands free on my Lumia 800..is that a known issue?

Hi,
this is a JDeveloper and ADF forum, not an OA framework forum. We don't have the "OAGlobalButtonBean" class and thus wont be able to help
Frank

Step backward hotkey not working while using brush tool? - Photoshop CC 2014

Hi,
I'm using Photoshop CC 2014 in Mavericks. I've tried using the step backward hotkey (command+option+z) and it seems to work fine. Then I use the brush tool and it stops working until I switch to another tool. I'm a digital artist, so I move very quickly while painting, and switching out of the brush tool to step backward on something slows me down terribly. I'll switch and the hotkey works as intended. I've tried changing it to a different set of keys (for example command+z) with the same results. Is this a bug or a feature?

Usually it turns out for tablets that aren't mainstream that they just haven't updated their drivers to work with photoshop cc.
For example, most people don't have problems with wacom tablets in photoshop cc.
One other thing that could possibly be the cause besides the tablet driver is your graphics card driver.
If in photoshop cc you go to Edit>Preferences>Performance and turn off Use Graphics Processor and then restart photoshop cc, does that make a difference?
If it does then perhaps your graphics card driver needs to be updated from the maker of the card.
(not through windows updates)

Hello I am using Ipad 4 and its charger is not working while I was using it few days before and it was working properly now it says that the cable does not support this Ipad Please Help me out.

Hello I am using Ipad 4 and its charger is not working while I was using it few days before and it was working properly now it says that the cable does not support this Ipad Please Help me out.

Try a reset:
- Hold the home button and sleep/wake button down at the same time. When the Apple logo appears release both buttons then try and charge again.
If issue persists try:
- Another known working cable
- Check the charging port for any damage or debris
- You could also use a dry soft bristle toothbrush and gently brush it on the port to clean it of any debris that could be in there

Iphone 6 plus fingerprint is not working while charging

My iphone 6 plus fingerprint scan is not working while charging. Is this normal?
I tried my iphone 5s and it works just fine even while charging.

I think I got an answer to my own question
If you're using generic lightning cable (non-original lighting cable), the fingerprint scan doesn't work while charging.
I just find it weird as my iphone 5s works even if i'm not using the original lightning cable though.

Why is Time machine backup not working after Mavericks upgrade?

Why is Time machine backup not working after Mavericks upgrade?

I had the same problem due to the Fire Wire port. Apple tested it told me it is OK!, I tried a new cable, and have tested both ports on my back up device. I find it strange that as soon as I installed Mavericks. The drive does work using USB. It could be a coincidence, I don't absolutely know at this point, my back up drive ports could stop working, but I doubt it!

I have checked the box "display date and time on the Menu Bar" and it does not work. Using OS X Yosemite 10.10.2 Anybody have a fix?

I have checked the box "display date and time on the Menu Bar" and it does not work. Using OS X Yosemite 10.10.2 Anybody have a fix?

Please read this whole message before doing anything.
This procedure is a test, not a solution. Don’t be disappointed when you find that nothing has changed after you complete it.
Step 1
The purpose of this step is to determine whether the problem is localized to your user account.
Enable guest logins* and log in as Guest. Don't use the Safari-only “Guest User” login created by “Find My Mac.”
While logged in as Guest, you won’t have access to any of your documents or settings. Applications will behave as if you were running them for the first time. Don’t be alarmed by this behavior; it’s normal. If you need any passwords or other personal data in order to complete the test, memorize, print, or write them down before you begin.
Test while logged in as Guest. Same problem?
After testing, log out of the guest account and, in your own account, disable it if you wish. Any files you created in the guest account will be deleted automatically when you log out of it.
*Note: If you’ve activated “Find My Mac” or FileVault, then you can’t enable the Guest account. The “Guest User” login created by “Find My Mac” is not the same. Create a new account in which to test, and delete it, including its home folder, after testing.
Step 2
The purpose of this step is to determine whether the problem is caused by third-party system modifications that load automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Please take this step regardless of the results of Step 1.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of Steps 1 and 2.

Backup not working for File Server

We have System Center 2012 Sp1 installed with Agent Version : 4.1.3453.0
We are protecting File Server which is member in DFS. We have Volume of More than 2TB and which is spanned accross multiple VHDs.
I am facing problem with Backup not working and DPMRA service is getting stopped unexpectedly. When i try to create recovery point manually i don't get option to syncrhonize the changes. 1st and 3rd option is geryed out.
I am getting Error on DPM as Affected area:   E:\
Description:   The replica of Volume E:\ on<ServerName> is inconsistent with the protected data source. All protection activities for data source will fail until the replica is synchronized with consistency check. You can recover data
from existing recovery points, but new recovery points cannot be created until the replica is consistent.
For SharePoint farm, recovery points will continue getting created with the databases that are consistent. To backup inconsistent databases, run a consistency check on the farm. (ID 3106)
   DPM failed to communicate with the protection agent on <Server> because the agent is not responding. (ID 43 Details: Internal error code: 0x8099090E)
   More information
Recommended action:   1) Check recent records from the DPMRA source in the Application Event Log on FUSE.win2k.internal to find out why the agent failed to respond.
2) Make sure that the DPM server is remotely accessible from <Server>
3) If a firewall is enabled on the DPM server, make sure that it is not blocking requests from <Server>
4) Restart the DPM Protection Agent service on <Server>. If the service fails to start, re-install the protection agent.
   Synchronize with consistency check.
   Run a synchronization job with consistency check...
Resolution:   To dismiss the alert, click below
   Inactivate
I have Re-installed Agent but it is not helping.
I have Other Volume labeled as F: and sized at 600 GB. Backup of that Volume is working fine for Same server.
Please Suggest how to troubleshoot.
Thanks in Advance.
Swapnil
Thanks, Swapnil Prajapati

HI Chris,
Sharing files using Bluetooth
To share files using Bluetooth, you first need to make sure Bluetooth is turned on, and then use Bluetooth File Exchange to send a file.
To turn on Bluetooth:
Choose Apple menu > System Preferences and click Bluetooth.
Select the On checkbox. To allow other Bluetooth enabled devices to “discover” your computer and send files, also select the Discoverable checkbox.
Select “Show Bluetooth status in the menu bar” so you can quickly send files and perform other actions using the Bluetooth status menu in the menu bar.
To send files using Bluetooth:
Choose Send File from the Bluetooth status menu in the menu bar.
If the Bluetooth menu isn’t visible, choose Apple menu > System Preferences, click Bluetooth, and select “Show Bluetooth status in the menu bar.”
In the window that appears, select the file you want to send and click Send.
Select the device you want to send the file to and click Send.
If you don’t see the device you want to send the file to, make sure the device has Bluetooth turned on and is discoverable.
You do not need File Sharing turned on for Bluetooth technology.
Another way to share files between two Macs is How to use Firewire Target Disk Mode
Carolyn

HT1665 i have an apple IPhone4. I am experiencing certain problem with my iphone4. The problems are as follows a. my ear piece and proximity sensor is not working while making a call. 2. It cannot reproduce sound without earphone but rings if gets any cal

Hi folks,
i have an apple IPhone4. I am experiencing certain problem with my iphone4. The problems are as follows a. my ear piece and proximity sensor is not working while making a call. 2. It cannot reproduce sound without earphone but rings normally if gets any call.
Can any one help me in this regard??

Try to reset the phone by holding the sleep and home button for about 10sec, until the Apple logo comes back again. You will not lose data by resetting, but it can cure some glitches after installing new software or apps.

Some email images do not show while using the icloud web app. I can see the images on my IOS devices and in gmail but I only see a small gray box in the icloud web mail app. Load HTML images is checked in preferences.

Some email images do not show while using the icloud web app. I can see the images on my IOS devices and in gmail but I only see a small gray box in the icloud web mail app. Load HTML images is checked in preferences. Is there a solution to this issue?

I've seen the opposite issue. My wife recieved an email with jpg attachments. She couldn't see or print them on her iPhone 4S but they showed up fine in iCloud or in the mail app. I had her forward the email to herself and then they showed up. I assume there is an issue with how Apple is processing the attachments and resending causes them to get reformatted in a way that makes them easier to handle.
So yeah. Seems like some bugs. Hope Apple fixes them soon.

HT201320 I have IOS 7 5S and using mail. Receiving works great. Sending mail will not work. Using Centurylink. On my IOS 6 Iphone 4 it works great. Compared settings and they are identical. Now what?

I have IOS 7 5S and using mail. Receiving works great. Sending mail will not work. Using Centurylink. On my IOS 6 Iphone 4 it works great. Compared settings and they are identical. Now what?

Well, this is a recurring issue for many users...a small percentage of users but still a bug. Report the issue here to Apple: www.apple.com/feedback
iOS7.0.3 will be released next week, which as of now, I know is primarily for an iMessage but hopefully it will clear up some of these email issues some are also having.

ERD not determined while using plain http adapter as Sender

Hi All,
ERD is not determined while using Plain Http Adpter as Sender.Is there any way to determine ERD table by using Http adapteras Sender?
Regards,
Rajesh

Are you doing synchronous scenario???
if yes should have leaving the value for the Software Component Version empty for Receiver determination .
/people/venkataramanan.parameswaran/blog/2006/03/17/illustration-of-enhanced-receiver-determination--sp16
/people/jin.shin/blog/2007/12/11/sap-netweaver-process-integration-enhanced-receiver-determination-for-synchronous-scenarios

ISE backup not working while using tftp

Similar Messages

Maybe you are looking for