Ise & vlan load balancing (user balancing)

As far as I know anb based on some esperience in a test environment it seems that cisco ISE among two load balancing radius kind of attributes supports only vlan gropu assignment, this means that on the switches vlan group assignment is required.
A second method of passing multiple vlans or vlan IDs by radius attributes is not allowed.
Am I wrong?
The issue I'm trying to overcome is the following
Subnet1 /24
Subnet2 /22
Many, many switches
(and the situation can't be changed)
Assuming the vlan assignment is local to the switch and with a round robin method, once the IPs are exhausted on Subnet1 only half of the clients that authenticate will obtain an IP (on Subnet2) while the rest will get stuck on Subnet1 without an IP
The same situation comes up when considering an odd number of authenticated clients on every switch and with two /24 subnets: it is likely possible that Subnet1 will be "full" before the second subnet does falling in the previous situation.
is there any solution?
thank you in advance

Don,
You are right. I should have said - Forte uses its own partitioning scheme
not the default scheme you see when you open partition workshop.
Nirmal
From: Don Nelson <[email protected]>
To: Nirmal P Uppalapati <[email protected]>
Cc: [email protected]
Subject: Re: Load Balancing, User Visible Service objects, Running man
Date: Wednesday, October 22, 1997 10:45 PM
Nirmal,
One note on the "running man"...
At 08:12 PM 10/22/97 -0500, Nirmal P Uppalapati wrote:
3. Running Man
When you run an application by clicking on the running man Forte uses
its
default partitioning scheme and runs the application. The partitionscheme
that you made will be used only when you run the application distributedor
from the partition workshop. This is the time you might encounter errorsif
your partitioning is not right.
Actually, clicking on the "running man" from the repository or project
workshop will cause the application to be run VERY differently thanrunning
it distributed.
It's not technically correct to say that the default partitioning schemeis
used with the running man.
Forte consulting offers a deployment workshop that covers the finerpoints
of this and other distributed issues.
Don
============================================
Don Nelson
Regional Consulting Manager - Rocky Mountain Region
Forte Software, Inc.
Denver, CO
Corporate voice mail: 510-986-3810
aka: [email protected]
============================================
"If you ask me, though, any game without push-ups, hits, burns or noogies
is a sissy game." - Calvin

Similar Messages

Load Balancing, User Visible Service objects, Runningman

1. Load Balancing
Load Balancing a partition has nothing to do with single or multi-threaded
behaviour of that partition. If you load balance a partition it means that
you can start 1 or more copies of that partition. How many to start can be
specified. If the partition is load balanced there will be router partition
that routes calls to any of the services in that partition.
Now let us look at a special kind of partition (load balanced partition
that has an Env visible SO and a user visible DbSession). This is one of
the design patterns to acccess the database efficiently. Each of these
partitions are single threaded because DbSession is inherently single
threaded. This partition is single threaded because Dbsession is single
threaded and not because the partition is replicated.
Another case is when you make a partition load balanced and it has only
SO(s) made out of tool classes and does not have Dbsessions then each of
these partitions can run multi-threaded beacuse there are no
single-threaded objects to make the partition single threaded
2. User Visibility
Case A - If you have only User visible SO(s) in a partition then each
behaves like a global named object. Whoever accesses it will get a copy of
their own.
Case B - If you have a user visible SO and an Env Visible SO in the same
partition then the user visible SO will be private to the partition and
cannot be accessed from outside that partition.
3. Running Man
When you run an application by clicking on the running man Forte uses its
default partitioning scheme and runs the application. The partition scheme
that you made will be used only when you run the application distributed or
from the partition workshop. This is the time you might encounter errors if
your partitioning is not right.
Hope this helps.
Nirmal

Don,
You are right. I should have said - Forte uses its own partitioning scheme
not the default scheme you see when you open partition workshop.
Nirmal
From: Don Nelson <[email protected]>
To: Nirmal P Uppalapati <[email protected]>
Cc: [email protected]
Subject: Re: Load Balancing, User Visible Service objects, Running man
Date: Wednesday, October 22, 1997 10:45 PM
Nirmal,
One note on the "running man"...
At 08:12 PM 10/22/97 -0500, Nirmal P Uppalapati wrote:
3. Running Man
When you run an application by clicking on the running man Forte uses
its
default partitioning scheme and runs the application. The partitionscheme
that you made will be used only when you run the application distributedor
from the partition workshop. This is the time you might encounter errorsif
your partitioning is not right.
Actually, clicking on the "running man" from the repository or project
workshop will cause the application to be run VERY differently thanrunning
it distributed.
It's not technically correct to say that the default partitioning schemeis
used with the running man.
Forte consulting offers a deployment workshop that covers the finerpoints
of this and other distributed issues.
Don
============================================
Don Nelson
Regional Consulting Manager - Rocky Mountain Region
Forte Software, Inc.
Denver, CO
Corporate voice mail: 510-986-3810
aka: [email protected]
============================================
"If you ask me, though, any game without push-ups, hits, burns or noogies
is a sissy game." - Calvin

Debit,credit ,opening balance,closing balance..doubt.

Dear friends,
               I am working in FI report (vendor balance for date ranges) .Its a ALV report. I want to fetch the datas for debit ,
credit,opening balance,closing balance,for the paticular vendor or all vendors for date ranges.the table for this iam using is BSIK AND LFC1.
all the datas stored in the table is for month wise,but my programe (my user needs even for day wise) how to calculate this,
or is there any function modules avaliable or can u konw any other table storing day wise balances...this report is urgent ..
any one pls suggest me .advance thanks..
regards
veera

if user wants day wise then make use of BSAK+BSIK, here u will get all line items daywise , i mean to say Posting daywise.
BUDAT        31.03.2003---->posting date
BLDAT        31.03.2003
CPUDT        31.03.2003
WAERS        INR
XBLNR        T&E-29-30.3-PNPT
BLART        PA
MONAT        3
BSCHL        31
ZUMSK
SHKZG        H------------>D/C
GSBER--------------------->Business Area
MWSKZ-------------------->tax Code.
DMBTR        1,507.00
WRBTR        1,507.00
regards
Prabhu

Difference of balance in balance sheet report & Business area wise report

Dear Group Members!!
In my company user wants to generate Business are wise Report
Difference of balance in balance sheet report & Business area wise report from same t code
Balances are different if enter business area, & if I execute the report with out entering any business area. Transaction code S_ALR_87012284 - Balance Sheet / Profit and Loss Statement.
The difference amount to be considered as data entry made with out using business area?
How do I rectify this?
Your comment will be helpful for me
Shamulheq

Hi Shamulheq
While working with business area you must first recognize that they are not company code dependent and can be used cross-company. Also depending on the SAP release you are working with postings to Business Area may not 100% guarantee, since there are cases where rules or standard SAP is not available and line items posted will be carried out without BA. For SAP releases not using the NEW GL, the setting up of adjustments accounts and monthly execution of adjustment programs would provide the vehicle to relate and adjust any missing BA at B/S and P/L level. If you are using NEW GL the document splitting would help to set the rules where every single line item would get a business area.
I assume that you are using the classic GL. The execution of T code S_ALR_87012284 - Balance Sheet / Profit and Loss Statement without business area retrieves all posting entered for any given company code regardless the account was posted with or without business area, this can be clearly displayed when you select the radio button for Classic Navigation. If you filter by Business Area, then the report will isolate the output data accordingly (The balances should be smaller). When using the classic GL you have to make sure that the financial statement version you use to execute the report, includes that the technical (Adjustment accout) account(s) that is used for the adjustment programs, so the correction to buisness areas is also included.
In conlcusion I think you have to make all this considerations, in order to better understand where the differences come from.
Hope this helps.
GG

(@ISMBR beginning balance, ending balance circular ref?

essbase circular reference
in excel it's time consuming to update but doable in essbase its turned into a circular reference even when I try breaking up the process
Beginning Bal member takes original data for 2011 Jan
for formula member Beginning Balance to pick up
Measures
Reconciliations
Beginning Bal (data is loaded for Jan 2011)
Beginning Balance formula member
Total payments
Payments(+)
Payment Adjustments(+)
Total Accruals
Accruals (+)
Accrual Adjustments(+)
Total Payments & Accruals formula member (Total payments + Total Accruals)
Ending Balance formula member("Beginning Balance"+ "Total Payments & Accruals")
Beginning balance formula
IF (@ISMBR("FY 2011") and @ISMBR("JAN"))
"Beginning Bal";
ELSEIF (@ISMBR("FEB"))
"Ending Balance" ->"JAN";
ELSEIF (@ISMBR("MAR"))
"Ending Balance"->"FEB";
ELSEIF (@ISMBR("APR"))
"Ending Balance"->"MAR";
ELSEIF (@ISMBR("MAY"))
"Ending Balance"->"APR";
ELSEIF (@ISMBR("JUN"))
"Ending Balance"->"MAY";
ELSEIF (@ISMBR("JUL"))
"Ending Balance"->"JUN";
ELSEIF (@ISMBR("AUG"))
"Ending Balance"->"JUL";
ELSEIF (@ISMBR("SEP"))
"Ending Balance"->"AUG";
ELSEIF (@ISMBR("OCT"))
"Ending Balance"->"SEP";
ELSEIF (@ISMBR("NOV"))
"Ending Balance"->"OCT";
ELSEIF (@ISMBR("DEC"))
"Ending Balance"->"NOV";
ELSEIF (@ISMBR("FY 2012") and @ISMBR("JAN"))
"Ending Balance"->"DEC";
ENDIF
/* for the Qtrs formula member */
IF (@ISMBR("QTR1"))
"Ending Balance"->"MAR";
ELSEIF (@ISMBR("QTR2"))
"Ending Balance"->"JUN";
ELSEIF (@ISMBR("QTR3"))
"Ending Balance"->"SEP";
ELSEIF (@ISMBR("QTR4"))
"Ending Balance"->"DEC";
ENDIF
begining balance and ending balance break if a change is made within Total payments and accruals; it may do the next month but it doesn't do all the months across the year and then the next year and it also breaks at the qtrs?????
anyone have any ideas.. hace tried intermediary formulas, terms...

Then begiining balance doesn't have any data becuase
data is in Jan beginning bal member.
Jan beginning bal = Jan beginning balance
'Beginning Balance is a formula member consisting of formula member ending balance.
Ending balance is a formula= beginning balance + total accruals+ total payments
beginning balance = @ prior months ending balance issue can't seem to get order for essbase to figure out cotrrectly...because its back and forth between ending balance and begining balance..

ISE vlan mapping.

have one query for ISE 1.2
Is the following scenario is supported with ISE?
Can we configure ISE VLAN mapping with SSID authentication web auth only.

Limitations
No support for guest clients – posture for guest user is not supported.
Hreap local switching is not supported -
No support for wlans without 802.1x support
Client will go through posture during slow roam – when client is associated used 802.1x (not wpa2 or cckm) then when client roams from one wlc to other – wlc will send new session ID hence client will again go through posture validation process.
No support for guest tunneling mobility
Mac auth bypass is not supported
Vlan pooling is not supported.
No support for WGB AP
No support for AP group.
Kindly find the link information regarding integration is mention.
https://supportforums.cisco.com/docs/DOC-18121

Error loading C:\Users\User Name\AppData\Local\HpWebNotifier\SyncNetOffice.dll

Everytime I start up my computer I get a pop-up that states: 'Error loading C:\Users\User Name\AppData\Local\HpWebNotifier\SyncNetOffice.dll'
My computer and printer work fine but this message is annoying. I can't figure out what the problem is. I am wondering if it is an issue from an old printer that I used to be connected to that I've already uninstalled. Does anyone have any ideas how I can resolve this issue?
Thanks!
This question was solved.
View Solution.

Hello lisabar90,
What operating system is the computer?
What model computer are you using?
Try this click on start and then run and type msconfig and hit enter.
(if your computer doesn't have a run type msconfig in the search box and click on the application)
Go to the startup tab and see if you can see a reference to that location. Uncheck it and reboot your computer.
Post back your results.
If I have helped you in any way click the Kudos button to say Thanks.
The community works together, click Accept as Solution on the post that solves your issue for other members of the community to benefit from the solution.
- Friendship is magical.

Unable to load the user interface-please reinstall the application-Audigy 2 zs Platinum

unable to load the user interface-please reinstall the application---this is the message I get when my pc starts------Someone messing around with my computer tried to delete creative media source player 3 when they saw I had both 3 and 5 in folder and i get this error message every time I start my pc. In addition to this I have lost my EAX and THX consoles and my speaker settings are gone so I cannot adjust my 5. system at all. After I delete that error message when I click on the creative icon is sys tray instead of opening up the creative media player I get the error message--unable to load needed componants. Please reinstall the application. this is media player 3[version 3.32.]. I dont know why during the auto?updates through the last couple of years I have media player 3 in sys tray and if I need version 5 it is in file with 3--start-all programs-creative--any way my pc is a Cyberpower AMD FX-53 using win xp pro-32 bit-- and of course its a OEM product so they tell me the only way to get it to work is use the restoration cd they gave me when I bought the pc and it will revert back to its original state as when purchased. I would lose all my games, music, pictures?ect and would have to start from scratch.[ OR of course back everything up on a portable hard dri've]?It seems like there should be an easier way --hell I might as well buy a new soundcard and it would make it easier. If anyone?has an answer for someone who is not a tech head so I can understand please help !!--thank you in advance for any assistance as it is greatly appreciated. Sorry this message is so long winded, just irritating to have spen so much for a pc and not have the original installation disc.-tried moving to another slot and the fixes I saw posted here with no luck---thank you folks again--Tom

All the issues you guys are talking about have been reported in beta stage of these new drivers. I would say none of them has been fixed yet. The only solution for now is to use previous drivers which work fine or use some modified drivers which fixes some issues, but not all. Your choice.
[url="http://connect.creativelabs.com/windows/Lists/Audigy%20Issues/AllItems.aspx">Bug List[/url]
Message Edited by ronon0 on 08-07-2008 :47 AM

Windows cannot load the user's profile but has logged you on with the default profile for the system.

My Windows 7 crashed a couple days ago after a windows update, I got this message.
Windows cannot find the local profile and is logging you on with a temporary profile. Changes you make to this profile will be lost when you log off.
I restarted the machine and got this message
Windows was unable to load the registry. This problem is often caused by insufficient memory or insufficient security rights.
DETAIL - The process cannot access the file because it is being used by another process. for C:\Users\TEMP\ntuser.dat
I checked the event Log I found these .
Windows cannot load the user's profile but has logged you on with the default profile for the system.
DETAIL - Only part of a ReadProcessMemory or WriteProcessMemory request was completed.
Windows has backed up this user profile. Windows will automatically try to use the backup profile the next time this user logs on.
Windows cannot load the locally stored profile. Possible causes of this error include insufficient security rights or a corrupt local profile.
DETAIL - The process cannot access the file because it is being used by another process.
This is the first error in the event viewer after a successful logon
The description for Event ID 34 from source ccSvcHst cannot be found. Either the component that raises this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on the local computer.
If the event originated on another computer, the display information had to be saved with the event.
ccSetMgr
Windows cannot load the user's profile but has logged you on with the default profile for the system.
DETAIL - Access is denied.
Looking at the Logs all I can tell is that after the Desktop Window Manager started if caused this error.
The winlogon notification subscriber <SessionEnv> was unavailable to handle a notification event.
then this one
The Desktop Window Manager has exited with code (0x40010004)
Then this before it shutdown.
The User Profile Service has stopped.
I started up the PC and the first message I got was
How can I get access to my user profile? do I need to createa new Administrator account? Please help
The EventSystem sub system is suppressing duplicate event log entries for a duration of 86400 seconds. The suppression timeout can be controlled by a REG_DWORD value named SuppressDuplicateDuration under the following registry key: HKLM\Software\Microsoft\EventSystem\EventLog.

hi do the following
1. In Search programs and files (Windows 7) area, type in regedit, and press Enter.
2. If prompted click yes,
3. expand the following HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\ProfileList
4. click the sid that related to your admin profile (if you not sure, click each sid and in turn look to the right hand side of registry editor it will show who that sid is related to one of the registry files should hae in description localhost\admin or
something similair)
5. right click the sid and press delete.
6. restart your machine and log back on with the admin account, this will then rebuild the admin profile... dont worry when it loads and none of your personal settings are saved or files or folders... go to c:\users
in here you will see two folders for the admin account, one will be just admin and the other most likely admin.localhost
i cant remember which one is which but just check both, one will still have all your files and folders in it.
i suggest making a backup of your data before doing this incase something does go wrong, but ive had this happen many times in a domain enviorment and has worked for me everytime.

Error: One or more categories of approval could not be loaded when user wants to approve

Two of my PM's are getting the error shown in the title of this post (Error: One or more categories of approval could not be loaded when user wants to approve).    The "Related Topic" issues a work around of using the rules to "automatically approve the
offending items".   This did not work for us.   Has anyone else experienced this issue?
Thanks,
~RK

Hi Marc - Per ytour request:
The PM does the following:
1. Access PWA Home page and review messages
2. Clicks on “You have 1 timesheet from resources pending your approval” message
3. Approval Center Page loaded with “Error: One or more categories of approval could not be loaded” and “There are no new approvals to review at this time. If you have published your plan and
still do not see approvals, have your resources submit updates from “Tasks” of “Timesheet”” messages.
We've made certain the Schedule is published and the timesheet was submitted correctly.
Expected behavior: Timesheet records should be available for review and approval.   Instead, the PM gets the screen below with the error message

Table Field of Opening Balance & Closing Balance

Hi,
I want the table field of Opening Balance & Closing Balance for G/L Account Balance (ref. t. code FS10N).....
From where i can get these field...
Thanks

Hi,
Activate SQL trace (ST05), and run the transaction to create a new entry or change the value of an existing, then deactivate the trace.
we can see the tables that updating the transaction.
Hope this will help you....
Regards,
Pavan

Opening Balance & Closing Balance

Hi Guru's
How could we evaluate opening balance, Closing balance and movements per GL accounts on FIGL extactor?
Regards,
Ramana.

Hi,
below links will be helpful for you.
Opening Balance
Getting Opening & Closing Balance in Customer Ledger Report
Thanks...

SAP P & L Report does not balance to Balance sheet profit

Dear support,
I have a client that we have just taken over and they have a strange problem with their financial reports. The profit on the P & L Report does not balance to the profit on the balance sheet? The trial balance still balances so I am not sure whee the difference is coming from??
It has not balanced since the first take on balance were brought int othe system. Is it possible that some account with balances were moved from a P & L draw to a Balance sheet draw in the chart of accounts? If so how do I find the problem account?
Regards
Clayton

I resolved this issue myself.

Error loading C;\users\Toshiba\appData\Local\SMBDP.dll

Can anyone help me?
After i start up i keep getting a message that says error loading C;\users\Toshiba\appData\Local\SMBDP.dll and then the module could not be found.
I have tried everything but cannot get rid of it,
i have asked for help online but it tells me to purchase a Tune-up utilities, but i already have Tune-up untilities and have run it through completely but it still does'nt work,
please help.

I don't believe this error message has anything to do with Toshiba applications you got preinstalled with your laptop so it is not easy to identify which application want to have access to this data.
Is anything else written in this error message?

Report painter un balanced in balance sheet

Dear Experts,
can you please help me
When i run report painter In T C : GRR3, i saw balance sheet balance is unbalanced that is liablities is not matched to assets . it shows out of balance .
How i can verify this unbalanced amount
Regards
Bhaskar

Hi ,
Can uyou please explain me , how to check asset line item and GL line item in which T C and how to reconcil
Regards
Bhaskar

Ise & vlan load balancing (user balancing)

Similar Messages

Maybe you are looking for