ISE works with Local-switch Mode

Hi guys,
My AP is configured to work as Flexconnect mode with my WLC, that means that my wireless data will be switched locally without getting through my WLC, is that ok for my ISE to controll my wireless access?
Regards,

Yes; FlexConnect supports central authentication with both locally and centrally switched traffic models.
Lots of info about FlexConnect here;
http://www.cisco.com/en/US/docs/wireless/controller/7.4/configuration/guides/flexconnect/config_flexconnect_chapter_01.html

Similar Messages

Multiple VLANs per SSID with local switch

Is it possible to use an 'AP Group' or 'Interface group' to assign multiple VLANs to a WLAN when remote, h-reap APs are in local switch mode?
If not, is there a way to overcome 500 maximum host per VLAN when APs are local switching?
Thanks!

dont think its possible...
I donno if the following config will even work but u can have the hreap APs connected at the remote site to map to different vlans...
Example:
AP1 -- ssid 1 --- vlan 10
AP2 -- said 1 --- vlan 11 and so forth..
Sounds crazy but i ll have to ponder on this a bit more.. Need a pen and paper to draw a quick topology :)...
Sent from Cisco Technical Support iPhone App

Working with local files at c:\temp ...

Hi!
My report is working with local files (this is a must). I know that i can't use such a report in a planned job in the background. Are there nevertheless any options for me starting this report regularly in an automatic way? ...Perhaps on a pc which is always logged/switched on?
Thanks in advance!
Best regards,
Ingo

Hi,
why didn't you check the sy-batch (test if it's a background job) ?
use the DIR_TEMP of the SAP server when it's a background job.
to get the physical directory you could use this kernel function :
CALL 'C_SAPGPARAM' ID 'NAME' FIELD 'DIR_TEMP'
ID 'VALUE' FIELD searchpoints-dirname.
(dirname is a CHAR 75)
Rgd
Frédéric

Buffer table not up-to-date error while working with local SRM PO

Hi all,
We are working in SRM 7.0 with extended classic scenario.
I faced an issue while working with local SRM PO. Iam getting a dump while doing changes in SRM PO.
Dump says that "Buffer table not up-to-date". Please find the detail dump error below :
http://cscgsapndc34.nwk.amer.csc.com:8114/sap/bc/webdynpro/sapsrm/wda_l_fpm_oif/
UNCAUGHT_EXCEPTION
Buffer table not up-to-date
Function: BBP_PD_ABORT of program SAPLBBP_PDH
Form: ABORT of program SAPLBBP_PDACC
Form: ACCOUNT_INTERNAL_SAVE of program SAPLBBP_PDACC
Function: BBP_ACCOUNT_INTERNAL_SAVE of program SAPLBBP_PDACC
Form: PROCDOC_INTERNAL_SAVE of program SAPLBBP_PD
Form: STATUS_SET_AND_INTERNAL_SAVE of program SAPLBBP_PD
Form: PROCDOC_UPDATE of program SAPLBBP_PD
Function: BBP_PROCDOC_UPDATE of program SAPLBBP_PD
Method: /SAPSRM/IF_PDO_UPDATE_BUFFER~SUBMIT of program /SAPSRM/CL_PDO_UPDATE_BUFF_PO=CP
Method: /SAPSRM/IF_PDO_BASE~SUBMIT_UPDATE of program /SAPSRM/CL_PDO_BASE===========CP
http://cscgsapndc34.nwk.amer.csc.com:8114/sap/bc/webdynpro/sapsrm/wda_l_fpm_oif/
If anyone of you already came across this type of dump error can you please let me know what might be the possible reasons for the same . Request your kind help in this regard.
Thanks in advance.
Regards,
Kalyani

There could be many issues..
or some data issue.
can you recreate the same issue you can fix it.
it could only one incident so you should thoroghly check what piece of data is wrong.
what actions are you doing in the purchase order.
Note 1580496 - Purchase order Buffer table not upto date dump in change ver
Symptom
1.Create a change version on any Purchase order.
2. Edit quantity of any item
3. Dont press 'Enter key'
4. Clickk on Order button.
Application gves dump 'Buffer table not upto date'
but it is very difficult to say what is the issue. request your technical resource to look your dump.
if you recreate the issue half of the problem resolved.

New 150/65 only at 94 Download AND Won't Work with Gigabit Switch

I just had this installed today, converting up from the 35/35, and ran into these two problems:
1. The 150 download is only resulting in a 94.87 Mpbs. The installer originally said it must be my PC NIC card, but I do have a GB card, so there's does not appear to be legitimate reason for the shortfall there. I tried to change the link speed and duplex from "auto negotation" to "1 Gbps Full Duplex," but then my computer no longer even could connect.
2. The second issue is that I have always run my connection through a D-Link DGS-2208 Gigabit Switch because I have multiple wired ethernet computers in my office. The installer wanted to test the connection speed directly through my computer (see above) and ran into problems, so I never even tried to revert to my original setup with the switch until he left. However, when I did the Gigabit switch does not even recognize any activity when I plug the source ethernet cord into the switch. It does recognize the connection to the PC and the port is lit, but no lights from connection to the wall.
Any thoughts on what the problems could be? I've included the "additional details" from the Fios Speed test at the standard site (can't get any details from the high speed version):
Checking for Middleboxes . . . . . . . . . . . . . . . . . . Done
SendBufferSize set to [261360]
running 10s outbound test (client to server) . . . . . 42.90Mb/s
running 10s inbound test (server to client) . . . . . . 69.90Mb/s
------ Client System Details ------
OS data: Name = Windows 7, Architecture = x86, Version = 6.1
Java data: Vendor = Oracle Corporation, Version = 1.7.0_05
------ Web100 Detailed Analysis ------
Client Receive Window detected at 65340 bytes.
622 Mbps OC-12 link found.
Link set to Full Duplex mode
No network congestion discovered.
Good network cable(s) found
Normal duplex operation found.
Web100 reports the Round trip time = 6.78 msec; the Packet size = 1452 Bytes; and
No packet loss - but packets arrived out-of-order 0.02% of the time
This connection is receiver limited 37.88% of the time.
Increasing the the client's receive buffer (63.0 KB) will improve performance
This connection is sender limited 61.7% of the time.
Web100 reports TCP negotiated the optional Performance Settings to:
RFC 2018 Selective Acknowledgment: ON
RFC 896 Nagle Algorithm: ON
RFC 3168 Explicit Congestion Notification: OFF
RFC 1323 Time Stamping: OFF
RFC 1323 Window Scaling: OFF
Information: Network Middlebox is modifying MSS variable
Server IP addresses are preserved End-to-End
Information: Network Address Translation (NAT) box is modifying the Client's IP address
Server says [{edited for privacy}] but Client says [192.168.1.16]
Solved!
Go to Solution.

tdaignault wrote:
I tried to change the link speed and duplex from "auto negotation" to "1 Gbps Full Duplex," but then my computer no longer even could connect.
If your computer can't negotiate a 1Gbps connection, then that is what is limiting you to 94Mbps, which is about right for a "100Mbps" port.
There could be several reasons for this.
A bad NIC
A bad port on the switch
IMO, the most likely cause is a bad cable. 1Gbps requires all 4 pairs in the cable be connected. If only 2 of the 4 pairs are connected correctly, you will get a 100Mbps connect, but will not be able to connect at 1Gbps. Try replacing the cable with one known to work at 1Gbps.

Help needed to configure H-REAP with local switching

Hi All,
We are using following devices for campus Wi-fi.
1. WLC - 4402
2. AP (1131ag, 1042n) which support H-REAP.
I want to configure HREAP central auth and local switching. I have enabled from local to HREAP after that I go to HREAP tab and native vlan 1 (by default)(I have changed native vlan 1 to 51.) vlan support is enabled. then click on vlan mapping and my wlan (guestwlan) is there with vlan id 24.
I have assigned static IP to AP (192.168.51.40/24 gw 192.168.51.254).
DHCP is running on controller.
switch port configure is below:
interface FastEthernet0/18
description WiFi access point
switchport trunk native vlan 51
switchport mode trunk
no ip address
end
Issue : authentication done through RADIUS (Cisco ACS 4.2) but no getting IP address from DHCP.
Please help.
Thanks in Adv.
Thanks,
AS

Hi AS,
Do not use the DHCP on the WLC.
Use a DHCP on the neighbor swtich if possible for the native VLAN.
Regards,
Amjad
Rating useful replies is more useful than saying "Thank you"

How to setup new site in dreamweaver if not working with Local Site Folder?

Dear All,
I am working with a website design (wordpress) project with a group of people, since we are working together on the same design, our developing site is not located in the local folder but on remote server, but I can't setup the website in DW if the developing site is not located locally.
Is there any way to do the development on remote server with DW, and what will be the site setup setting for it?
thanks for any reply.
bruce

Sharing a "Local" site is a recipe for disaster vis-a-vis file versioning. The best way to avoid these problems is to have three locations defined:
1. A local site (truly local to your computer, although it can be on a network, shared drive).
2. A staging site (this would be the intermediate holding site for partially finished work.
3. A production site (this would be where the final versions of files are pushed).
Enable DW's Checkin/Checkout facility. Each of you would checkout files from the staging server, and when finished editing, checkin those same files to the staging server. Thus, you are not sharing a local site - you are sharing a remote file repository, which is your gold standard source for version protected files.
Make sense?

Working with local xml file

Hi, I would like to work with a local xml file, but I don't want to point to a strict location as I would like my application to run on a few different machines.
Is there a special place within Netbeans project structure that I can place such files?
Say if I try and load a file "somefile.xml" - where is it going to look first?
I have a <default package> with my settings.xml in there. How can I reference this within my app?
Edited by: 993541 on Mar 16, 2013 9:25 AM

993541 wrote:
Is there a special place within Netbeans project structure that I can place such files?dunno Netbeans project structure at all but I'd sugest maven project structure wich is widely used: http://maven.apache.org/guides/introduction/introduction-to-the-standard-directory-layout.html
There you would place such a file in the <tt>main/resources</tt> folder
Say if I try and load a file "somefile.xml" - where is it going to look first?I'ts going to look for it where you tell your program to.
When created as <tt>new File("somefile.xml")</tt> it will bee searched in the <i>currend working directory</i>. The problem with that is that it is unreliable what this will be at runtime (once your Program left your IDE...).
You should better get it via <tt>getClass().getResource("somefile.xml")</tt> But in this case the file must be present in the classpath in the same package as the Class aquireing it. Adding a <tt>'/'</tt> in front of the file name expects it in the root directory of a classpath entry.
I have a <default package> with my settings.xml in there. How can I reference this within my app?<tt>getClass().getResource("/settings.xml")</tt>
But in case you include it into the delivery jar file it will not be writable. Also you cannot expect the installation folder of your App to be writable. On startup of your program you should copy your (default) settings to a writable place like <tt>new File(System.getProperty("user.home2),".myApp/settings.xml");</tt> and modify it there.
bye
TPD

Apple TV doesn't work with HDMI Switch

Apple TV doesn't seem to work with my HDMI Switch. Tried every combination of cables. Tried switching all devices on and off at different times. Googled to see if anyone else has tried a switcher with Apple TV. All I know is: PlayStation 3 works just fine running through the switcher. Apple TV doesn't work at all with the switcher, only when plugged directly into the TV.
I only have one HDMI port on my Samsung HDTV and two HDMI devices (PlayStation 3, Apple TV). All my component slots are full and I already have a component switcher that's full, too. So HDMI is the only option for me.
Any ideas? Switcher claims to support HDCP... and it does do HD resolutions (PS3 displaying in 720p).

I use this 5x1 switch from Monoprice and it works fine, switching 3 devices, which are then routed through my AV receiver's switch... Despite the convoluted hookup, I have not had HDCP handshake issues.
http://www.monoprice.com/products/product.asp?cid=101&cp_id=10110&cs_id=1011002&pid=2777&seq=1&format=2&style=
The nice thing about this switch is:
1. It works: no discernable loss in quality, switches relatively quickly, etc.
2. It's cheaper than many others, like Gefen, or even the Xtrememac (which is 4x1)
3. The remote has discrete buttons for each input, which is very helpful when setting up a universal remote like my Harmony 880. I can't tell from the Xtrememac picture if it's a direct input, or if you can only cycle through the inputs...
Good luck!
MacBook Mac OS X (10.4.9)

Urgent-- could cisco uc320 work with dumb switch ? how to configure

could cisco uc320 work with dumb poe switch, with its voice vlan alway in 100, I can't change it, and my phone can not find the pbx through the switch, if it can, how can I configure it.

Hi Rex,
If the switch is unmanaged the 802.1q (tagged) ethernet frames typically pass right through the switch as if the phone was directly connected to the UC320W. In this case both voice VLAN works and data VLAN. I would guess that if a switch has PoE that it is a managed switch though. If it is a managed switch you will need to configure ports, vlans, and possibly CDP passthrough.
Chris

Remote Desktop doesn't work with local printer

I am having trouble using a locally networked printer when I use Remote Desktop to connect to a Vista machine. Under the local resources tab for RD, I have checked printers. The only thing I can figure is that my printer is networked locally, not connected directly to my machine. Every time I try to print during my remote desktop session, I can't access my locally networked printer.
I installed the printer drivers on the remote computer and when I try to locate the printer, I get the following error: "Windows cannot connect to the printer. Server print spooler service is not running..." but the spooler service IS runing.
I also found a post elsewhere that discussed setting 'share permissions' and 'network permissons' to resovle the spooler error. Still no go.
I tried to plug in my printer to a local USB port this morning. Still would not work. I keep getting the same spooling error. The drivers are not corrupt, as others have indicated may be the cause. They work fine on my system locally with 7.
Any advice would be greatly appreciated. I've spent a few hours on this one and am at a loss at this point.
Please help. I really need to print locally.

My problem was that the Vista remote system never saw local port that my printer was using for some reason and it never accepted the path noted above (\\servername\printer)...always came back with an error that it was an invalid path. This was with it both networked and plugged in via USB port.
I finally figued it out after four days and many hours on the phone with Microsoft. Microsoft support claimed that it was related to my router settings, but I didn't believe it since the remote computer saw my iPhone just fine when it was connected locally. After simply playing around, here's what I found...it was actually quite basic!
On the remote system, when you try to add a 'local' printer, there's a drop down menu with a list of local ports that your remote system sees. Some of those will be on the remote system, but others will be on your local system. Make a note of the ones that are seen on your local system. In my case, LPT1 was not visible, but COM3 was.
Next, on your local system, in the settings for your functioning printer (Printer Properties, Ports Tab), there's a tick box that says "Enable Printer Pooling." Once you check that box, you can select multiple ports on your local machine. Here, you need to tick the box that your remote system is seeing (in my case, it's COM3), but make sure that your exisitng port remains checked as well (in my case, an IP port for my wireless router). Basically what you're doing is on your local system, you are pooling your exising printer setup with a port that can be seen by your remote system.
Then, on the remote system, install the printer drivers but don't select a port. Then go into Printers and add a printer. Select 'local' setup for that and when asked for the port, use the port you checked in the previous step on your local system (in my case, I selected COM3 on my local system). Select your printer from the list. It will ask if you want to use the exisiting drivers...say yes. Then print a test page to be sure that it works. Worked fine for me.
I simply can't believe how obvsious that solution was! If the remote system can't see the port you currently use, pool your printer setup with a port that it can see!

Firmware 3.01 no longer works with HDMI switch

I've been using an Octava 4x2 Matrix switch with 2 Apple TV devices for 6 months without issue. Unfortunately, the firmware upgrade to 3.01 has rendered the switch useless, as the Apple TV devices refuse to show picture and have to have a hard power resets in order to work properly - each and every time they are switched over. This is very, very annoying. Also, I use two DVDO EDGE switches and upscalers which have similar problems with the Apple TV devices since the firmware upgrade. Sometimes they are able to sync sound with the Apple TVs but not picture and at other times, vice versa. This is causing me tremendous grief. What in the world did Apple do in 3.01 to render all my equipment useless? I spend more time in my AV cabinet than I do watching Apple TV! Not a workable scenario. Please allow us to roll back to 3.0. Life was much simpler then.

"What is interesting is that you didn't have these issues in v 3.0 whereas most seem to have had similar issues with both v 3 and v 3.0.1."
Mine is switched through a HK receiver and it worked fine in 3.o as well. It quit switching every time when upgraded to 3.0.1. I am shocked by Apple's lack of response with this matter. I am quickly losing faith in their products because of this. It would be so easy to allow users to downgrade to 3.0 but they won't even comment on the situation.

BrowserLab won't work with local files in DW CS5

Any issue report you make about BrowserLab on these forums should minimally contain the following information. If it doesn't, the first response you get from us will likely just ask for the missing info anyway
Subject
A descriptive summary of the issue.
The body should contain:
Problem Description
A brief description of the bug or issue
Steps to Recreate
The steps we should follow to reproduce your issue. Minimally include all the following:
Does the issue happen every time, is it sporadic, or did it only happen once.
Are you testing on Mac or Windows?
Are you using the main BrowserLab interface, testing via Dreamweaver integration (and if so, what version of DW), or using the BrowserLab for Firebug add-on?
What is the URL you're testing against. If it's not public, let us know and let us know if you can send us the page source.
Expected Results
Based on the steps you described, what you thought should happen
Actual Results
What actually did happen
Thanks everyone,
Mark
Using BrowserLab in DW 11.0 Build 4964, BrowserLab can't seem to work. Some not very intuitive places I have checked include making sure the signon credentials are in the CSLive window in DW.
In preview local/browser, the following messages are disappointing me:
Timed Out, Failed to Authenticate with Browserlab
Session Expired, See Browser
It is on a Mac, 10.6.7, using DW integrated testing. I can log into browserlab and put a public URL, but I don't think that's going to be much better for me than having VMWare and installing free browsers on Mac and Windows, and given the failures here that would be better for local file checks too. I write this because I wonder if I will be disappointed trying to get this to work and then find out I have to pay a yearly subscription to CSLive to be able to keep using it.
This is on a private URL and I can send the page source, but I don't think its the page that is causing the issue.
Expected results:
Able to preview page in any browser of my choosing
Actual results:
Spent the last two hours navigating help, googling possible solutions, getting many errors trying to navigate the Adobe help and forums, continually signing in on each adobe page I open. Expecting to have to reauthenticate to post this message. (Updated extension manager as well).

Hi,
First, there is no charge currently for using CSLive and there won't be any charge for another year.
Second, based on what you're saying about the behavior you're seeing with BrowserLab and the issues you had with continually having to sign onto the Adobe pages, it's a strong indication that you've got cookies disabled in your browser or that something on your machine is deleting/expiring the cookies we are trying to set. What browser/version are you using and what kinds of permissions have you got set for cookies in that browser? Can you check that and change your cookie permissions for Adobe.com at least?
Let me know if that helps or not,
Mark

Working with Local Files

I have to develop a Web-Based application to run on each client's pc. Or, it could be to run on our intranet. This is for internal use only. The requirements are very simple:
1. Web-Based
2. Able to access local client's files
3. Able to upload files via FTP
4. Able to access a MySQL database to query some data
I recently developed a Desktop Application using Visual Basic 2008 Express .Net 3.5. It works ok. Application will look for .pdf files on a specific folder on C: drive, rename the files according to some user's input and database query result, then upload the renamed files to an FTP server. No problem. However, the company don't want a desktop application. So, my goal is to re-create the application using a new Rich Internet Application technology. I then, created a Windows User Control in VB.net 3.5 and embedded the .dll in an html page. This works great on my local development pc, however, it will have some security issues when I try to run it on our intranet. It seems like the control (Activex), will not allow access to the local files. I just need access to be able to rename files on C:, that's it. Then I came across Silverligt and Flex development software. But, after playing with flex for a little, noticed that Flex will not be my best choice to access and rename local files. Any suggestions about the technology that we should use?
Will I be able to accomplish this type of application using a Java Applet?
Thanks!

Hi,
why didn't you check the sy-batch (test if it's a background job) ?
use the DIR_TEMP of the SAP server when it's a background job.
to get the physical directory you could use this kernel function :
CALL 'C_SAPGPARAM' ID 'NAME' FIELD 'DIR_TEMP'
ID 'VALUE' FIELD searchpoints-dirname.
(dirname is a CHAR 75)
Rgd
Frédéric

PPTP VPN works with local but not RADIUS authentication

iPhone OS v3.1
My VPN server is a Draytek 3300v. The iPhone connects OK when an account is set up locally on the server, but as soon as I switch it to use a RADIUS server (no other settings changed), authentication fails. I have tried 2 different RADIUS servers, with the same result. Immediately after successful authentication comes back from RADIUS, the VPN server log shows:
pppd: peer 'john.smith' authenticate succeed, protocol:49699
MSCHAP-v2 peer authentication succeeded for john.smith
rcvd [LCP TermReq id=0x2]
LCP terminated by peer
pptpd: EOF or bad error reading ctrl packet length
pptpd: cannot read packet header, exit
pptpd: read pptp packet failed
Clients using various versions of Windows all connect OK, but the iPhone fails authentication both over the carrier network and wireless.
Any ideas anyone?

Have you checked the Enterprise Deployment Guide for 3.1? It's at http://www.apple.com/support/iphone/enterprise

ISE works with Local-switch Mode

Similar Messages

Maybe you are looking for