ISIS Redistribution

I'm having a couple problems with mutual redistribution between ISIS and EIGRP.
A little setup, I was trying to redistribute only level-1 routes into EIGRP and it would redistribute both L1 and L2 routes. I know that I have both L1 and L2 routes in the routing table on the redistribution router. The configuration I've been using is:
router eigrp 1
redistribute isis level-1 metric 100 100 200 1 1500

The following output shows an IS-IS router redistributing static, RIP, IGRP, EIGRP, and OSPF routes.
router isis
network
redistribute static
redistribute rip metric 20
redistribute igrp 1 metric 20
redistribute eigrp 1 metric 20
redistribute ospf 1 metric 20The IS-IS metric must be between 1 and 63. There is no default-metric option in IS-IS?you should define a metric for each protocol, as shown in the example above. If no metric is specified for the routes being redistributed into IS-IS, a metric value of 0 is used by default.

Similar Messages

I do 'router isis' but I get 'protocol not in this image'

C2610, IOS 12.3.
I've searched this on forums but I couldn't find the answer:
I attempt to do 'router isis' but IOS returns 'protocol not in this image'. How can I solve this ? I would like to work on ISIS redistribution labs against EIGRP, OSPF, etc.

Thanks for info. hmmm... I need to search it more, but so far it seems my image can't do ISIS...
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.3(12b), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Thu 31-Mar-05 19:08 by jfeldhou
Image text-base: 0x80008098, data-base: 0x80CCAA68
ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
ROM: C2600 Software (C2600-I-M), Version 12.3(12b), RELEASE SOFTWARE (fc2)
RouterC uptime is 8 hours, 16 minutes
System returned to ROM by power-on
System image file is "flash:c2600-i-mz.123-12b.bin"
cisco 2610 (MPC860) processor (revision 0x203) with 28672K/4096K bytes of memory
Processor board ID JAD05390K1C (3082946085)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
1 Ethernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
32K bytes of non-volatile configuration memory.
--More--

Adobe AIR Runtime Redistribution and Native Installer

Will there be new instructions for Adobe AIR 2.0 Runtime Redistribution? In particular, I'm looking for instructions on how to use the runtime redistribution installer to perform a "side-car installation" of AIR 2 alongside an application that uses the NativeProcess API (and so must be built into a native installer instead of a .air file).
Thanks!

Thirded!
On a test deployment using SCCM and the supplied Adobe AIR Runtime Installer files, we have managed to install our application with the 1.5.3 Air Framework with no major issues other than having to disable the Auto Update feature that doesnt really work in a corporate environment. Everything was absolutely fine until the release of AIR 2. Now, the test machines are prompted to install the updated Adobe Air 2 framework once a week, see an excerpt from an Adobe blog post below:
"In addition, once a week AIR apps check to see if an AIR update is available, and if so, users are presented with the option to update to the most up‐to‐date version, helping to ensure that end users get the benefits of improved security and performance."
That sounds great right? Except my users (like many other corporate users) don't have Admin permissions on their machines (hence the use of SCCM), with the result being resultant error messages when a user attemptes to install the AIR framework update without the necessary permissions.
All of the above would be fine if the Adobe AIR Runtime Installer files were updated to include the latest version of the runtime. This of course hasn't been done yet - does anyone know when this may happen? Can anyone help me with this or offer any advice?
I hope the above makes sense and I would really appreciate any help or advice!
Thanks!

HT4972 i connect my iphone to my pc and i tunes open automatically,then i press dowload and update but itunes say am not connected to the internet while my pc is connected to the internet what isi the problem?

i connect my iphone to my pc and i tunes open automatically,then i press dowload and update but itunes say am not connected to the internet while my pc is connected to the internet what isi the problem?

If you are the only user on your computer you probably don't have multiple user accounts set up and can disregard that. If you are using iTunes 11 go to View>Show Sidebar. Now see if your iPad appears under Devices on the left side when you connect it. If it does, click on the name of your iPad on the left side and your iTunes sync settings options will appear in folders with tabbed headings to the right.
If it doesn't appear on the left side, follow the troubleshooting steps shown in this article: http://support.apple.com/kb/TS1538.

Not working multitopology ISIS with IOS and IOS-XR

Hi everyone,
I've gon a problem setting up IPv6 routing with ISIS in the test network. There are four routers connected as shown on the image.
I've got problems setting up IPv6 routing in this topology. I tried single topology and multitopology ISIS. Neither of them works properly. Single topology simple does not come up when IPv6 is configured in ISIS. Multitopology yet comes up but uyields only working IPv4 roting. I can see that IPv6 ISIS RIB is buit by the routers, but it is not copied into the main routing table.
That's what I get in the multitopology mode:
All neignors are up.
R2#show isis neighbors
Tag null:
System Id Type Interface IP Address State Holdtime Circuit Id
R7 L1 Et0/2 2.2.27.7 UP 7 R7.04
R8 L1 Et0/1 2.2.28.8 UP 9 R8.03
R9 L1 Et0/0 2.2.29.9 UP 7 R9.01
Database in consistent on all four routers
R2#show isis database
Tag null:
IS-IS Level-1 Link State Database:
LSPID LSP Seq Num LSP Checksum LSP Holdtime ATT/P/OL
R2.00-00 * 0x0000001C 0x21DD 727 0/0/0
R7.00-00 0x00000011 0xF6EF 866 0/0/0
R7.04-00 0x00000007 0x5CD2 1117 0/0/0
R8.00-00 0x0000000B 0xD2EA 941 0/0/0
R8.01-00 0x00000006 0xF0C3 878 0/0/0
R8.03-00 0x00000006 0x7E39 805 0/0/0
R9.00-00 0x0000000B 0x4071 817 0/0/0
R9.01-00 0x00000006 0x8D2A 783 0/0/0
R9.03-00 0x00000006 0xE3CC 840 0/0/0
ISIS IPv6 RIB contains only local prefixes
R2#show isis ipv6 rib
IS-IS IPv6 process , local RIB
2002:2:2::7/128
2002:2:2:27::/64
2002:2:2:78::/64
2002:2:2:79::/64
IPv6 topology is not complete as if R8 and R9 were not in database
R2#show isis ipv6 topology
Tag null:
IS-IS TID 2 paths to level-1 routers
System Id Metric Next-Hop Interface SNPA
R2 --
R7 10 R7 Et0/2 0202.5a00.b120
R8 **
R9 **
A closer look at isis database:
R2#show isis database detail
Tag null:
IS-IS Level-1 Link State Database:
LSPID LSP Seq Num LSP Checksum LSP Holdtime ATT/P/OL
R2.00-00 * 0x0000001D 0x1FDE 1004 0/0/0
Area Address: 47.0002
Topology: IPv4 (0x0)
IPv6 (0x2)
NLPID: 0xCC 0x8E
Hostname: R2
IP Address: 2.2.0.2
Metric: 10 IP 2.2.0.2/32
Metric: 10 IP 2.2.29.0/24
Metric: 10 IP 2.2.28.0/24
Metric: 10 IP 2.2.27.0/24
IPv6 Address: 2002:2:2::2
Metric: 10 IPv6 (MT-IPv6) 2002:2:2:29::/64
Metric: 10 IPv6 (MT-IPv6) 2002:2:2:28::/64
Metric: 10 IPv6 (MT-IPv6) 2002:2:2:27::/64
Metric: 10 IPv6 (MT-IPv6) 2002:2:2::2/128
Metric: 10 IS-Extended R7.04
Metric: 10 IS-Extended R8.03
Metric: 10 IS-Extended R9.01
Metric: 10 IS (MT-IPv6) R7.04
Metric: 10 IS (MT-IPv6) R8.03
Metric: 10 IS (MT-IPv6) R9.01
R7.00-00 0x00000012 0xF4F0 1187 0/0/0
Area Address: 47.0002
Topology: IPv4 (0x0)
IPv6 (0x2)
NLPID: 0xCC 0x8E
Hostname: R7
IP Address: 2.2.0.7
Metric: 10 IP 2.2.0.7/32
Metric: 10 IP 2.2.78.0/24
Metric: 10 IP 2.2.79.0/24
Metric: 10 IP 2.2.27.0/24
IPv6 Address: 2002:2:2::7
Metric: 10 IPv6 (MT-IPv6) 2002:2:2:78::/64
Metric: 10 IPv6 (MT-IPv6) 2002:2:2:79::/64
Metric: 10 IPv6 (MT-IPv6) 2002:2:2:27::/64
Metric: 10 IPv6 (MT-IPv6) 2002:2:2::7/128
Metric: 10 IS-Extended R7.04
Metric: 10 IS-Extended R8.01
Metric: 10 IS-Extended R9.03
Metric: 10 IS (MT-IPv6) R7.04
Metric: 10 IS (MT-IPv6) R8.01
Metric: 10 IS (MT-IPv6) R9.03
R7.04-00 0x00000007 0x5CD2 640 0/0/0
Metric: 0 IS-Extended R7.00
Metric: 0 IS-Extended R2.00
R8.00-00 0x0000000B 0xD2EA 464 0/0/0
Area Address: 47.0002
NLPID: 0xCC 0x8E
Topology: IPv4 (0x0)
IPv6 (0x2)
Hostname: R8
IP Address: 2.2.0.8
IPv6 Address: 2002:2:2::8
Metric: 10 IS-Extended R8.01
Metric: 10 IS-Extended R8.03
Metric: 10 IP 2.2.0.8/32
Metric: 10 IP 2.2.28.0/24
Metric: 10 IP 2.2.78.0/24
Metric: 10 IPv6 (MT-IPv6) 2002:2:2::8/128
Metric: 10 IPv6 (MT-IPv6) 2002:2:2:28::/64
Metric: 10 IPv6 (MT-IPv6) 2002:2:2:78::/64
R8.01-00 0x00000007 0xEEC4 1155 0/0/0
Metric: 0 IS-Extended R8.00
Metric: 0 IS-Extended R7.00
R8.03-00 0x00000006 0x7E39 328 0/0/0
Metric: 0 IS-Extended R8.00
Metric: 0 IS-Extended R2.00
R9.00-00 0x0000000C 0x3E72 1035 0/0/0
Area Address: 47.0002
NLPID: 0xCC 0x8E
Topology: IPv4 (0x0)
IPv6 (0x2)
Hostname: R9
IP Address: 2.2.0.9
IPv6 Address: 2002:2:2::9
Metric: 10 IS-Extended R9.01
Metric: 10 IS-Extended R9.03
Metric: 10 IP 2.2.0.9/32
Metric: 10 IP 2.2.29.0/24
Metric: 10 IP 2.2.79.0/24
Metric: 10 IPv6 (MT-IPv6) 2002:2:2::9/128
Metric: 10 IPv6 (MT-IPv6) 2002:2:2:29::/64
Metric: 10 IPv6 (MT-IPv6) 2002:2:2:79::/64
R9.01-00 0x00000007 0x8B2B 1048 0/0/0
Metric: 0 IS-Extended R9.00
Metric: 0 IS-Extended R2.00
R9.03-00 0x00000007 0xE1CD 1091 0/0/0
Metric: 0 IS-Extended R9.00
Metric: 0 IS-Extended R7.00
I don't understand the following: Why R8 doesn't consider itself attached to Pseudonodes R8.01 and R8.03 in IPv6 topology? The same question about R9 and Pseudonodes R9.01 and R9.03 in IPv6 topology. R7 and R2 consider themselves as attached to Pseudonode R7.04, although R7.04 doesn't look much different from the rest of the Pseudonode LSPs in the database. This fact still doesn't allow them to calculate a correct RIB.
Am I missing something?
Configs of the devices is below:
######R2########
service timestamps debug datetime msec
service timestamps log datetime msec
hostname R2
boot-start-marker
boot-end-marker
vrf definition ABC
rd 2:2
address-family ipv4
route-target export 2:2
route-target import 2:2
route-target import 1002:2
exit-address-family
no aaa new-model
clock timezone PST 0
ip source-route
ip cef
ipv6 unicast-routing
ipv6 cef
multilink bundle-name authenticated
mpls label protocol ldp
interface Loopback0
ip address 2.2.0.2 255.255.255.255
ip router isis
ipv6 address 2002:2:2::2/128
ipv6 router isis
interface Ethernet0/0
ip address 2.2.29.2 255.255.255.0
ip router isis
ipv6 address 2002:2:2:29::2/64
ipv6 router isis
mpls ip
interface Ethernet0/1
ip address 2.2.28.2 255.255.255.0
ip router isis
ipv6 address 2002:2:2:28::2/64
ipv6 router isis
mpls ip
interface Ethernet0/2
ip address 2.2.27.2 255.255.255.0
ip router isis
ipv6 address 2002:2:2:27::2/64
ipv6 router isis
mpls ip
interface Ethernet0/3
no ip address
shutdown
interface Ethernet1/0
vrf forwarding ABC
ip address 172.2.142.2 255.255.255.0
interface Ethernet1/1
no ip address
shutdown
interface Ethernet1/2
no ip address
shutdown
interface Ethernet1/3
no ip address
shutdown
router isis
net 47.0002.0000.0000.0002.00
is-type level-1
metric-style wide
address-family ipv6
multi-topology
exit-address-family
router rip
version 2
address-family ipv4 vrf ABC
redistribute bgp 2 metric 1
network 172.2.0.0
no auto-summary
version 2
exit-address-family
router bgp 2
no bgp default ipv4-unicast
bgp log-neighbor-changes
neighbor 2.2.0.9 remote-as 2
neighbor 2.2.0.9 update-source Loopback0
address-family ipv4
no synchronization
network 2.2.0.2 mask 255.255.255.255
neighbor 2.2.0.9 activate
neighbor 2.2.0.9 send-community
no auto-summary
exit-address-family
address-family vpnv4
neighbor 2.2.0.9 activate
neighbor 2.2.0.9 send-community extended
neighbor 2.2.0.9 next-hop-self
exit-address-family
address-family ipv4 vrf ABC
no synchronization
redistribute rip
exit-address-family
no ip http server
mpls ldp router-id Loopback0
control-plane
line con 0
exec-timeout 0 0
privilege level 15
logging synchronous
line aux 0
line vty 0 4
login
end
######R7########
service timestamps debug datetime msec
service timestamps log datetime msec
hostname R7
boot-start-marker
boot-end-marker
vrf definition ABC
rd 2:2
address-family ipv4
route-target export 2:2
route-target import 2:2
route-target import 1002:2
exit-address-family
no aaa new-model
clock timezone PST 0
ip source-route
ip cef
ipv6 unicast-routing
ipv6 cef
multilink bundle-name authenticated
mpls label protocol ldp
interface Loopback0
ip address 2.2.0.7 255.255.255.255
ip router isis
ipv6 address 2002:2:2::7/128
ipv6 router isis
interface Ethernet0/0
ip address 2.2.78.7 255.255.255.0
ip router isis
ipv6 address 2002:2:2:78::7/64
ipv6 router isis
mpls ip
interface Ethernet0/1
ip address 2.2.79.7 255.255.255.0
ip router isis
ipv6 address 2002:2:2:79::7/64
ipv6 router isis
mpls ip
interface Ethernet0/2
ip address 2.2.27.7 255.255.255.0
ip router isis
ipv6 address 2002:2:2:27::7/64
ipv6 router isis
mpls ip
interface Ethernet0/3
no ip address
shutdown
interface Ethernet1/0
vrf forwarding ABC
ip address 172.2.17.7 255.255.255.0
interface Ethernet1/1
no ip address
shutdown
interface Ethernet1/2
no ip address
shutdown
interface Ethernet1/3
no ip address
shutdown
interface Serial2/0
no ip address
no fair-queue
serial restart-delay 0
interface Serial2/1
no ip address
shutdown
serial restart-delay 0
interface Serial2/2
no ip address
shutdown
serial restart-delay 0
interface Serial2/3
no ip address
shutdown
serial restart-delay 0
router ospf 100 vrf ABC
log-adjacency-changes
redistribute bgp 2 subnets
network 172.2.0.0 0.0.255.255 area 0
router isis
net 47.0002.0000.0000.0007.00
is-type level-1
metric-style wide
address-family ipv6
multi-topology
exit-address-family
router bgp 2
no bgp default ipv4-unicast
bgp log-neighbor-changes
neighbor 2.2.0.9 remote-as 2
neighbor 2.2.0.9 update-source Loopback0
neighbor 2002:2:2::9 remote-as 2
neighbor 2002:2:2::9 update-source Loopback0
address-family ipv4
no synchronization
network 2.2.0.7 mask 255.255.255.255
neighbor 2.2.0.9 activate
neighbor 2.2.0.9 send-community
no auto-summary
exit-address-family
address-family vpnv4
neighbor 2.2.0.9 activate
neighbor 2.2.0.9 send-community extended
exit-address-family
address-family ipv6
no synchronization
network 2002:2:2::7/128
neighbor 2002:2:2::9 activate
exit-address-family
address-family ipv4 vrf ABC
no synchronization
redistribute ospf 100 vrf ABC
exit-address-family
no ip http server
mpls ldp router-id Loopback0
control-plane
line con 0
exec-timeout 0 0
privilege level 15
logging synchronous
line aux 0
line vty 0 4
login
end
######R9########
hostname R9
telnet vrf default ipv4 server max-servers 100
username student
group root-lr
secret 5 $1$FJX6$23S1vUlkI7nuRNSFMWR8N0
aaa authentication login default local
cdp
vrf ABC
address-family ipv4 unicast
import route-target
2:2
1002:2
export route-target
2:2
control-plane
management-plane
out-of-band
interface MgmtEth0/0/CPU0/0
allow Telnet
interface Loopback0
ipv4 address 2.2.0.9 255.255.255.255
ipv6 address 2002:2:2::9/128
interface MgmtEth0/0/CPU0/0
ipv4 address 10.0.8.129 255.255.255.0
interface GigabitEthernet0/2/1/0
description uplink SW4
interface GigabitEthernet0/2/1/1
description uplink R2, R5
interface GigabitEthernet0/2/1/1.29
description - VLAN 29 (R2)
ipv4 address 2.2.29.9 255.255.255.0
ipv6 address 2002:2:2:29::9/64
dot1q vlan 29
interface GigabitEthernet0/2/1/1.59
description - VLAN 59 (R5)
vrf ABC
ipv4 address 172.2.59.9 255.255.255.0
dot1q vlan 59
interface GigabitEthernet0/2/1/2
description uplink R6, R7
interface GigabitEthernet0/2/1/2.69
description - VLAN 69 (R6)
ipv4 address 2.2.69.9 255.255.255.0
ipv6 address 2002:2:2:69::9/64
dot1q vlan 69
interface GigabitEthernet0/2/1/2.79
description - VLAN 79 (R7)
ipv4 address 2.2.79.9 255.255.255.0
ipv6 address 2002:2:2:79::9/64
dot1q vlan 79
interface GigabitEthernet0/2/1/3
shutdown
interface GigabitEthernet0/2/1/4
shutdown
interface POS0/2/0/0
shutdown
interface POS0/2/0/1
shutdown
interface POS0/2/0/2
shutdown
interface POS0/2/0/3
shutdown
route-policy default_policy_pass_all
pass
end-policy
router static
address-family ipv4 unicast
2.2.69.6/32 GigabitEthernet0/2/1/2.69
router isis abc
is-type level-1
net 47.0002.0000.0000.0009.00
address-family ipv4 unicast
metric-style wide
interface Loopback0
address-family ipv4 unicast
address-family ipv6 unicast
interface GigabitEthernet0/2/1/1.29
address-family ipv4 unicast
address-family ipv6 unicast
interface GigabitEthernet0/2/1/2.79
address-family ipv4 unicast
address-family ipv6 unicast
router bgp 2
address-family ipv4 unicast
network 2.2.0.9/32
address-family vpnv4 unicast
address-family ipv6 unicast
network 2002:2:2::9/128
address-family vpnv6 unicast
neighbor 2.2.0.2
remote-as 2
update-source Loopback0
address-family ipv4 unicast
next-hop-self
address-family vpnv4 unicast
route-reflector-client
neighbor 2.2.0.7
remote-as 2
update-source Loopback0
address-family ipv4 unicast
next-hop-self
address-family vpnv4 unicast
route-reflector-client
next-hop-self
address-family ipv6 unicast
next-hop-self
address-family vpnv6 unicast
next-hop-self
neighbor 2.2.0.8
remote-as 2
update-source Loopback0
address-family ipv4 unicast
next-hop-self
address-family vpnv4 unicast
route-reflector-client
next-hop-self
neighbor 2.2.69.6
remote-as 1002
address-family ipv4 unicast
route-policy default_policy_pass_all in
route-policy default_policy_pass_all out
address-family vpnv4 unicast
route-policy default_policy_pass_all in
route-policy default_policy_pass_all out
neighbor 2002:2:2::7
remote-as 2
update-source Loopback0
address-family ipv6 unicast
next-hop-self
neighbor 2002:2:2:69::6
remote-as 1002
address-family ipv6 unicast
route-policy default_policy_pass_all in
route-policy default_policy_pass_all out
vrf ABC
rd 2:2
address-family ipv4 unicast
redistribute eigrp 100
mpls ldp
router-id 2.2.0.9
interface GigabitEthernet0/2/1/1.29
interface GigabitEthernet0/2/1/2.79
router eigrp 100
vrf ABC
address-family ipv4
default-metric 100000 10 250 1 1500
autonomous-system 100
redistribute bgp 2
interface GigabitEthernet0/2/0/1.59
interface GigabitEthernet0/2/1/1.59
end
######R8########
hostname R8
telnet vrf default ipv4 server max-servers 100
username student
group root-lr
secret 5 $1$Y39m$k.fAmjkI6OEFDmiIfSkGt1
aaa authentication login default local
cdp
vrf ABC
address-family ipv4 unicast
import route-target
2:2
1002:2
export route-target
2:2
control-plane
management-plane
out-of-band
interface MgmtEth0/0/CPU0/0
allow Telnet
interface Loopback0
ipv4 address 2.2.0.8 255.255.255.255
ipv6 address 2002:2:2::8/128
interface MgmtEth0/0/CPU0/0
ipv4 address 10.0.8.128 255.255.255.0
interface GigabitEthernet0/2/1/0
description uplink SW3
interface GigabitEthernet0/2/1/1
description uplink R3, R7
interface GigabitEthernet0/2/1/1.38
description - VLAN 38 (R3)
vrf ABC
ipv4 address 172.2.38.8 255.255.255.0
dot1q vlan 38
interface GigabitEthernet0/2/1/1.78
description - VLAN 78 (R7)
ipv4 address 2.2.78.8 255.255.255.0
ipv6 address 2002:2:2:78::8/64
dot1q vlan 78
interface GigabitEthernet0/2/1/2
description uplink R2, R15
interface GigabitEthernet0/2/1/2.28
description - VLAN 28 (R2)
ipv4 address 2.2.28.8 255.255.255.0
ipv6 address 2002:2:2:28::8/64
dot1q vlan 28
interface GigabitEthernet0/2/1/2.158
description - VLAN 158 (R15)
dot1q vlan 158
route-policy default_policy_pass_all
pass
end-policy
router isis abc
is-type level-1
net 47.0002.0000.0000.0008.00
address-family ipv4 unicast
metric-style wide
interface Loopback0
address-family ipv4 unicast
address-family ipv6 unicast
interface GigabitEthernet0/2/1/1.78
address-family ipv4 unicast
address-family ipv6 unicast
interface GigabitEthernet0/2/1/2.28
address-family ipv4 unicast
address-family ipv6 unicast
router bgp 2
address-family ipv4 unicast
network 2.2.0.8/32
address-family vpnv4 unicast
neighbor 2.2.0.9
remote-as 2
update-source Loopback0
address-family ipv4 unicast
next-hop-self
address-family vpnv4 unicast
vrf ABC
rd 2:2
address-family ipv4 unicast
network 172.2.38.0/24
allocate-label all
neighbor 172.2.38.3
remote-as 123
address-family ipv4 unicast
route-policy default_policy_pass_all in
route-policy default_policy_pass_all out
as-override
send-extended-community-ebgp
mpls ldp
router-id 2.2.0.8
interface GigabitEthernet0/2/1/1.78
interface GigabitEthernet0/2/1/2.28
end
RP/0/0/CPU0:R8#

Hello,
Can you check on XR that you have option of enabling metric-style wide under ipv6 address-family.I'm not sure but i suppose you will also need to configure metric-style wide under ipv6 address-family as you are using multi-topology .IOS default run single topology and XR run default multi-topology.only need to be sure that you are running same topology and metric-style same on all router,in transition process like from multi to single or changing metric-style you can use "metric-style transition" option..
Regards,
Ashish

Isis driver on acrobat 10 pro

How do I get acrobat 10 Pro to recognize a canon DR 3080C-II Isis driver, the twain driver is listed but not the isis driver.

Michael is correct re: ISIS drivers.
Having made use of them I can attest that there are "Departmental" grade (and better) scanners using TWAIN drivers available that output at high page-per-minute rates (yes, even 80). As a new enterprise grade scanner is likely to not be available you may have to '2-step' - output TIFF then pull in the TIFF file(s) with Acrobat to output PDF.
Certainly an aggravation but I suspect what drivers are supported won't be changed any time soon.
What is specifically supported (from Acrobat Help):
On Windows, Acrobat supports TWAIN scanner drivers and Windows Image Acquisition (WIA) drivers. On Mac OS, Acrobat supports TWAIN and Image Capture (ICA).
Be well...

How do you Redistribution EIGRP into OSPF and maintain a distance of 250 for a static route?

Ok, I have scoured the forums long enough and have to post. The design is below. I moved a firewall to our new data center, which required adding some static routes for VPN connections and broadband backups. To minimize the amount of static routes I redistribute static into EIGRP with a route-map and prefix-list.
My problem is the next part of my network. When the data leaves my 56128's it hits an edge device connecting to our dark fiber. On this edge device I am running OSPF onto the dark fiber, then redistribute some EIGRP subnets into OSPF and again all is well.
Everything works up until the point the redistributed routes hit my RIB at my main data center where I am running IBGP. IBPG is run between our MPLS router and core for all our remote sites. When my backup route from the 56128's hits the cores, it supersedes the BGP route because the AD route O E2 [110/20] is lower than the BGP AD B [200/0]. Given the configuration below what can be done to remedy this? Oh when I redistribute I can only change the AD for the backup routes, all other routes should stay the same.
56128's where my static routes are:
ip route 192.168.101.0/24 192.168.30.77 name firewall 250
router eigrp 65100
redistribute static route-map Static-To-Eigrp
route-map Static-To-Eigrp permit 10
match ip address prefix-list Static2Eigrp
ip prefix-list Static2Eigrp seq 2 permit 192.168.101.0/24
Edge device:
router eigrp 65100
network 172.18.0.5 0.0.0.0
network 172.18.0.32 0.0.0.3
network 172.18.0.36 0.0.0.3
redistribute ospf 65100 metric 2000000 0 255 1 1500
redistribute static metric 200000 0 255 1 1500 route-map STATICS_INTO_EIGRP
passive-interface default
no passive-interface Port-channel11
no passive-interface Port-channel12
eigrp router-id 172.18.0.5
router ospf 65100
router-id 172.18.0.5
log-adjacency-changes
redistribute eigrp 65100 subnets route-map EIGRP_INTO_OSPF
passive-interface default
no passive-interface GigabitEthernet1/0/1
no passive-interface GigabitEthernet1/0/2
no passive-interface GigabitEthernet2/0/1
no passive-interface GigabitEthernet2/0/2
network 172.18.0.0 0.0.255.255 area 0
ip prefix-list EIGRP_INTO_OSPF seq 5 permit 172.18.0.0/16 le 32
ip prefix-list EIGRP_INTO_OSPF seq 10 permit 192.168.94.0/29 le 32
ip prefix-list EIGRP_INTO_OSPF seq 15 permit 192.168.26.32/29 le 32
ip prefix-list EIGRP_INTO_OSPF seq 20 permit 192.168.30.72/29 le 32
ip prefix-list EIGRP_INTO_OSPF seq 25 permit 192.168.20.128/25 le 32
ip prefix-list EIGRP_INTO_OSPF seq 26 permit 192.168.101.0/24 le 32 <- Backup Route for MPLS Remote Office
route-map EIGRP_INTO_OSPF permit 10
match ip address prefix-list EIGRP_INTO_OSPF

So in the case of a /24. If it were say broken up into /25's? From our remote sites we are using aggregate-address summary-only. Not sure how I would advertise a more specific route via BGP, sorry.
I didnt have this problem until I moved my firewalls. They plugged into the cores where IBGP was running and the static never kicked in unless the bgp route disappeared. I guess I could use my static redistribution for my VPN sites and use statics across the cores for the handful of backup links I have.

ERROR IN PROCESS VS REDISTRIBUTION WORKLOAD

Hello All
I create a shoping cart and cart went to ERROR IN PROCESS. and if i looked to to REDISTRIBUTION OF WORKLOAD search a requirement s(shopping cart) , why this ERROR IN PROCESS cart shows as COMPLETED (TICK GREEN MARK) . no one touched (i.e no Buyer completed a cart) . Why this cart shows as COMPLETED state.
Note 1164862 - Wrong Shopping Cart Status in 'Redistribute Workload'
Shopping Carts with status 'HELD' shown in transaction 'Redistribute Workload' with status 'COMPLETED'.
I am looking for the sap note for below problem
Shopping Carts with status 'ERROR IN PROCESS' shown in transaction 'Redistribute Workload' with status 'COMPLETED'.
Y Sourcing is completed.=SOURCE_REL_I ="Y" . but EROR IN PROCESS sc set as SOURCE_REL_I = ' '.
Y Sourcing is completed - It can be shown as GREEN TICK MARK in redistribution workload.
Why the ERROR IN PROCESS cart shows as COMPLETED .though my indicator is just SPACE
BR
Muthu

Hi Alen
I am pretty sure there is NO status caled COMPLETED in monitoring SC.
you we can not extract list what are the carts are completed by BUYER in the cockpit.
Muthu

Status 'in process' and 'complete' in workload Redistribution

hi expert.
In the workload redistribution, we found there are two status : "in porcess" and 'complete''. i do not know what's mean about them. and affect what ?
thanks in advance.
regards
claud

Hi Deepthi,
You can look for the "job log" status for the jobs in your process chain. For job logs use sm37 transaction an find the relative db table.
Hope this helps.
Bye
Dinesh

Isis problem with getting $40 credit

I'm hoping Verizon can help me. I was able to install the Isis mobile wallet on my new phone today. as i was going through the process, i started clicking on the links to terms and conditions. I had not yet finished signing up for Amex Serve, which has a $40 credit offer until 3/31. The problem is i was hitting the back arrow and somehow got out of Isis. Now if I go into my account, i don't have the $40 credit. I tried uninstalling and re-installing but it appears that I am now not considered a new Serve customer. Can anyone help? Plus i can't tell if i actually signed up for Amex Serve when I look into my account. There is no $40 credit for sure!

I think you may need to contact customer service regarding that matter. inlude the exact error message or notification in your message when you get in touch with them.
https://support.skype.com/en/faq/FA1170/how-can-i-contact-skype-customer-service
IF YOU FOUND OUR POST USEFUL THEN PLEASE GIVE "KUDOS". IF IT HELPED TO FIX YOUR ISSUE PLEASE MARK IT AS A "SOLUTION" TO HELP OTHERS. THANKS!
ALTERNATIVE SKYPE DOWNLOAD LINKS | HOW TO RECORD SKYPE VIDEO CALLS | HOW TO HANDLE SUSPICIOS CALLS AND MESSAGES

Any programs like ISIS Draw or Autonom for Mac OS X

Hi, I am a student and its frustrating that I cant seem to get any of these programs. These programs draw molecular formulas out for my Pharmacy Course.
Ppl with pcs laptops etc are able to and it puts me in a great disadvantage. And there are other things too... Mac aint good at compatibility...
ISIS Draw and Autonom works for older versions of mac i.e Mac OS but doesnt work on X.
Can anyone post a freeware drawing program you experienced that is good and easy installation... thanks.

Hello,
Here try this page
http://www.apple.com/downloads/macosx/imaging_3d/
Its a great site for looking for stuff like that.

Using Premiere Pro CS6 on an ethernet based SAN like Avid ISIS 5000

Hey all,
My post production facility currently runs both Avid Media Composer 6.5 and Adobe Premiere Pro CS6. We just recenetly started working on the Avid ISIS 5000 for our Avid editing projects. I know that Adobe Premiere Pro CS6 (according to Avid's website) is approved to work together.
I'm wondering on the Adobe Premiere side...are their general settings and practices we need to adhere to, when working with shared storage systems that are ethernet based? I'm running into some performance issues. Like long indexing and conforming when opening up a project on another station? And sometimes not being able to playback media or see media. When working locally, this doesn't seem to happen. I do not run into this when working in Avid Media Composer, so I dont' think it's any issues on my connectivity.
Has anyone had any experience running Premiere on an ISIS 5000 or other ethernet based SAN solution? Where can I find info on how to setup my scratch disks, projects, settings etc, for optimized use in a shared storage environment?

Premiere through version CS6 (or Cloud?) doesn't work properly, if at all, over a network
-see messages #1 and #3 in http://forums.adobe.com/thread/771151
-you MUST give all users administrator accounts to use Premiere
-and especially Encore dual layer http://forums.adobe.com/thread/969395
-#5 Server 2008 is UNsupported http://forums.adobe.com/thread/851602
-a work around, of sorts http://forums.adobe.com/thread/957523
-and not on a "domain" http://forums.adobe.com/thread/858977
A solution for networks
Adobe Anywhere http://www.adobe.com/products/adobeanywhere.html

Partition redistribution on node join

When a new node joins a distributed cache, I imagine that the partition assignment strategy will alter for the cluster in that some partitions must get assigned to the new node.
 This must mean that the primary location for some of the keys in the cache alters. What is the process for the data redistribution in this case for a distributed cache, i.e. when a new node joins?
 I have run a simple test, and it would appear that no redistribution occurs until some data is written / read. Is this always the case, or is there some background process that will migrate keys according to the new partition assignment?
 Is there someway to listen for re-assignment events, other than listening for individual get/remove actions on the keys in the backing maps as they get redistributed?
 Finally, how does the backup count for a distributed cache affect this? If it is set to 0 (no backups) is the process different?
 Any help gratefully received :)
 Regards
 Matt Searle

Matt,
 You are absolutely correct: when a new storage enabled node joins a partitioned cache service, the partition re-distribution protocol gets initiated and the new node will get a part of the overall load. The distribution algorithm is dynamic and adoptive, so as a matter of preference, the transfer affects cache parts that are not currently in active use.
 You can easily watch the process of cache data distribution by listening to the backing maps of the partitioned cache. Attached please find an example of cache configuration descriptor and a custom backing map listener class that would log all corresponding backing map events.
 Regards,
 Gene Attachment: dist-listen.xml (*To use this attachment you will need to rename 344.bin to dist-listen.xml after the download is complete.) Attachment: BackingMapListener.java (*To use this attachment you will need to rename 345.bin to BackingMapListener.java after the download is complete.)

SRM 7.0 SP05 - Workload Redistribution functionality

Hello,
Up on using the Workload redistribution functionality in our system the system dumps (strategic purchaser). The workload redistribution transaction does open initially but upon triggering the: search help / execute search via button or undo entries button the system dumps. It triggers the following error: 'User session (HTTP/SMTP/..) closed after timeout'.
- Does the 'Workload redistribution transaction' work in your system, could you test this?
- Is BW set-up required to run this transaction, does this functionality utilize BW?
- The customizing transaction 'Define Logical Systems and Template Names for BW Reports' is not available. How come? Is this transaction available in your system?
- Any possible solutions are very much welcome
Kind regards,
Tim

It seems that after using and waking up the functionality and letting the system rest it started to work. I don't know what that is but I guess we should be happy it's working after all.
Thread closed, question answered.
Kind regards,
Tim

REDISTRIBUTION WORKLOAD REPORT

Hi All
have you ever extracted this REPORTING WORKLOAD in the redistribution menu.
What exactly this report gives to the business usuage? assume that i have connected with BW ?
Why BW report shows in SRM box?
How to activate this report:- Workload report is not active? I do have BW system . how can achieve this?
i am in Define logical systems and template names for BW reports.
WORKLOAD_REPORT1 Workload Reporting 0TPL_BBP_PO_Q005_V02
which logical system i should give ? SRM or BW ?
aNY GUIDANCE IS APPRECIATED.
Muthu

Hello Muthu,
BW reports will be shown in SRM Box if the corresponding BW roles for SRM are integrated with SRM roles.
You might to activate the corresponding datasource of this in SRM.
And since you have to connect the source system to BW, I think you have to define SRM system as logical system in BW.
Regards,
Pavan

ISIS Redistribution

Similar Messages

Maybe you are looking for