ISM-SRE-300-K9 & Cisco Configuration Professional Issue

hi there,
i have a cisco 2901 router running CME 8.6 the router has a ISM-SRE-300-K9 card init with Unity Express 8.0.5 installed.
i am having issues with Cisco configuration professional and configuring the module
under module configuration the status is "module is not reachable", if i click on details i get further information "unable to execute command from the module. module is either reloading or is in failed state. you must make the module up and refresh the module"
i have tried reloading, resetting and refreshing the module but the issue is still present
i have accessed the module from the CLI set it in offline mode and factory defaulted it and the same issue is still present
the only thing i can think is that this is a bug with CCP as the loopback interface which the module is using can be pinged fine from the router so the message makes no sense.
any ideas

Is you problem with CCP or the module itself ?
Because, CCP bugs and limitations aside, the module can be normally be installed, configured and managed using CLI or its web interface (after software is initially loaded).

Similar Messages

ISM-SRE-300 don´t allow send data between clients and pc in LAN

I have an ISM-SRE-300 on cisco 1941 does not allow sending of data between clients attached to an AP wired to PC Networking.
LAN CLIENT= VLAN 20 10.94.4.0 /24
SERVER CLIENTE = 10.94.4.1 D.G= 10.94.4.254
ROUTER
INT G0/0.1= IP UNNUMBERED VLAN 1 NATIVE VLAN
INT G 0/0.20 = IP UNNUMBERED VLAN 20
INT VLAN 1 = 94.4.1.1 /24
INT VLAN 20 = 10.94.4.254 /24
ISM-SRE
MANAGEMENT UNTAGGED 94.4.1.2
VLAN 20 VLAN=20 IP=10.94.4.251 /24 D.G. 10.94.4.254
IF SENDING PING FROM ROUTER TO SERVER=10.94.4.1 IS OK
IF SENDING PING FROM ISM TO SERVER DON´T ANSWER
IF JOIN A CLIENT IN AP, CLIENT WIRELESS=10.94.4.150 /24 D.G. 10.94.4.254
I SEND PING TO ISM 10.94.4.251 IS OK
I SENG PING TO ROUTER 10.94.4.254 DON´T ANSWER
I SEND PING FROM SERVER (10.94.4.1) TO ROUTER 10.94.4.254 IS OK
I SEND PING TO ISM 10.94.4.251 DON´T WORK
I SENG PING TO CLIENT WIRELESS 10.94.4.150 DON´T WORK
CAN ANYONE HELP ME ?
THANKS
JUAN-RAMON

Just to be clear, this posting is NOT asking for help. This is a posting to help those with the HARDWARE side of the configuration. This is what I just finished doing in my lab for testing. Worked great. DHCP, WLAN Advertising, etc. I now have to go on to the next harder steps of really combing through the WLC configuration, applying our standard template configurations for our Routers/Switches, applying dual and tertiary redundancy with regards to routing, DHCP via MICROSOFT and not using a switch, and so on.
This was just meant to help those who don't have a lot of experience configuring the router switch environment. Sorry if I confused any one.

Cisco 2901-CME-SRST and ISM-SRE-300-K9 No Package already installed?

Good Morning Everybody,
I'm installing a new CME router with CUE.
But, the ISM-SRE-300-K9 is empty, I don't if it's normal.
I try to install two different packages :
Version 8.5.1
cue-installer.sme.8.5.1
cue-vm-full-k9.sme.8.5.1.prt1
cue-vm-installer-k9.sme.8.5.1.prt1
cue-vm-k9.sme.8.5.1.key
cue-vm-k9.sme.8.5.1.pkg
cue-vm-k9.sme.8.5.1.pkg.install.sre
cue-vm-k9.sme.8.5.1.pkg.install.sre.header
cue-vm-langpack.sme.8.5.1.pkg
Version 8.6.1
cue-installer.SPA.sme.8.6.1
cue-vm-full-k9.SPA.sme.8.6.1.prt1
cue-vm-installer-k9.SPA.sme.8.6.1.prt1
cue-vm-k9.SPA.sme.8.6.1.key
cue-vm-k9.SPA.sme.8.6.1.pkg
cue-vm-k9.SPA.sme.8.6.1.pkg.install.sre
cue-vm-k9.SPA.sme.8.6.1.pkg.install.sre.header
cue-vm-langpack.sme.8.6.1.pkg
Without success...
I try with two differents FTP server (Linux and Windows), connection and session seems ok with Wireshark, but, module go to loop, without installation success.
Different try :
Version 8.5.1
==========
Router#$0 status
Service Module is Cisco ISM0/0
Service Module supports session via TTY line 67
Service Module is trying to recover from error
Service Module heartbeat-reset is enabled
Service Module is in fail open
Service Module status is not available
Module resource information:
CPU Frequency: 1068 MHz
Memory Size: 493 MB
Disk 0 Size: 4110 MB
Install of ftp://*****:*****@10.10.80.68/Downloads/cue-vm-k9.sme.8.5.1.pkg in progress
Install status : Waiting for file request
Local Partition Info - (0 apps)
=====================
Retrieving partition information
Router#
Feb 16 06:04:22.583: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:29:03.839: %SYS-5-CONFIG_I: Configured from console by vty0 (10.10.80.68)
Feb 16 06:29:19.915: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:30:01.283: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:30:21.711: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:30:42.143: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:31:02.571: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:31:22.995: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP Registration Request
Feb 16 06:31:22.999: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:31:43.419: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:32:03.843: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:32:45.275: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:33:05.699: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:33:26.119: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:33:46.543: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:34:06.979: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP Registration Request
Feb 16 06:34:06.983: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:34:27.399: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:34:47.831: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:35:29.263: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:35:49.687: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:36:10.119: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:36:30.563: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:36:50.983: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP Registration Request
Feb 16 06:36:50.987: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:37:11.467: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:37:31.887: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:38:13.399: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:38:33.815: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:38:54.243: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File RequestConnection closed by foreign host.
Version 8.6.1
==========
Router#[email protected]/Downloads/cue-vm-k9.SPA.sme.8.6.1.pkg
Proceed with installation? [no]: yes
Feb 16 07:16:21.235: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP Registration Request
Loading Downloads/cue-vm-k9.SPA.sme.8.6.1.pkg.install.sre !
[OK - 38648/4096 bytes]
No local store partition
Following languages are available for installation.
#       SKU    Language Code           Language Name
1       ARA         ar_SA          CUE Voicemail Arabic
2       DAN         da_DK          CUE Voicemail Danish
3       DEU         de_DE          CUE Voicemail German
4       ENG         en_GB          CUE Voicemail UK English
5       ENU         en_US          CUE Voicemail US English
6       ESO         es_CO          CUE Voicemail Latin American Spanish
7       ESP         es_ES          CUE Voicemail European Spanish
8       ESM         es_MX          CUE Voicemail Mexican Spanish
9       FRC         fr_CA          CUE Voicemail Canadian French
10       FRA         fr_FR          CUE Voicemail European French
11       HUN         hu_HU          CUE Voicemail Hungarian
12       ITA         it_IT          CUE Voicemail Italian
13       HBR         iw_IL          CUE Voicemail Hebrew
14       JPN         ja_JP          CUE Voicemail Japanese
15       KOR         ko_KR          CUE Voicemail Korean
16       NLD         nl_NL          CUE Voicemail Dutch
17       NOR         no_NO          CUE Voicemail Norwegian
18       PTB         pt_BR          CUE Voicemail Brazilian Portuguese
19       PTG         pt_PT          CUE Voicemail Portuguese
20       RUS         ru_RU          CUE Voicemail Russian
21       SVE         sv_SE          CUE Voicemail Swedish
22       TUR         tr_TR          CUE Voicemail Turkish
23       CHS         zh_CN          CUE Voicemail Simplified Chinese (PRC)
24       ZHH         zh_HK          CUE Voicemail Hong Kong Chinese
25       CHT         zh_TW          CUE Voicemail Traditional Chinese (Taiwan)
You can install upto 5 language(s) on this platform.
Please select the language(s) you want to install by entering the language number(s)
Languages can be entered as comma separated or space separated list
Example: 1,3 would select 'CUE Voicemail Arabic' and 'CUE Voicemail German'
Enter languages:4
Following languages will be installed on the system:
CUE Voicemail UK English
Do you want to continue with the selected options?(y/n):y
Router#
Feb 16 07:16:50.579: %SM_INSTALL-6-INST_RESET: ISM0/0 is reset for software installation.
Feb 16 07:17:11.235: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP Registration Request
Feb 16 07:17:11.239: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
===========================
on the service-module ism0/0 session
===========================
Initializing memory. Please wait...
Memory initialization OK. Continue...
Feb 16 07:25:08.683: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
DDR Memory 0512 MB detected
Genuine Intel(R) processor              1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Primary Boot Loader Authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
SRE step 2 - SM requests key file info...
!!! Opcode Error - Get a wrong RBIP frame !!!
Feb 16 07:25:29.259: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP Registration Request
Feb 16 07:25:29.263: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Time-out from RBIP response wait loop
SRE step 3 - SM stores registration info...
Updating flash with bootloader configuration.
Please wait .............. done.
SRE step 4 - SM downloads key-file...
!!! Opcode Error - Get a wrong RBIP frame !!!
Writing keyfile to flash Size 891
writing complete.
SRE step 5 - SM requests installer info...
Feb 16 07:25:49.791: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
SRE step 6 - SM stores installer info...
Updating flash with bootloader configuration.
Please wait .............. done.
SRE step 7 - SM now downloads installer
|
!!! Opcode Error - Get a wrong RBIP frame !!!
Feb 16 07:26:10.343: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Requestdone.
SRE step 8 - SM requests tcl header file info...
!!! Opcode Error - Get a wrong RBIP frame !!!
Feb 16 07:26:52.919: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Time-out from RBIP response wait loop
SRE step 9 - SM now downloads the tcl header file
|
!!! Opcode Error - Get a wrong RBIP frame !!!
TCL header file downloaded completely size: 691
SRE step 10 - SM requests tcl file info...
Feb 16 07:27:13.467: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Time-out from RBIP response wait loop
SRE step 11 - SM now downloads the tcl file
!!! Opcode Error - Get a wrong RBIP frame !!!
Feb 16 07:27:34.011: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File RequestTCL file downloaded completely size: 691
SRE step 12 - SM now boots Installer
Verifying ...
Corrupted netboot image detected
done.
Starting Kernel.
loop ....
I have no idea to solve my problem...
If anybody have suggestion, should be great.
Have a nice day !
Thanks
Fab

Hi,
I try that. From this guide :
http://www.cisco.com/en/US/docs/voice_ip_comm/unity_exp/rel3_0/installation/guide/upg3boot.pdf
with windows xp tftpd32
computer config : 192.168.1.4/24
ftp server 192.168.1.3 /24
Router int g0/0 192.168.1.1 255.255.255.0 + ip route 192.168.1.2 255.255.255.255 ism 0/0
ISM :
ServicesEngine boot-loader> show config
IP addr:                    192.168.1.2
Netmask:                    255.255.255.0
TFTP server :                    192.168.1.4
GW IP addr:                    192.168.1.1
Default Boot:                    disk
Bootloader Version:          2.1.18
Bootloader Name:          bootloader
Default Helper-file:          cue-installer.sme.8.5.1
Default bootloader:          primary
From Computer :
C:\Documents and Settings\f>ping 192.168.1.2 -t
Pinging 192.168.1.2 with 32 bytes of data:
Reply from 192.168.1.2: bytes=32 time<1ms TTL=126
Icmp from ism to computer: no response.
from ism to router int g0/0 : no response too.
router to ism (boot-loader): ok
pc to ism (boot-loader) : ok
So when I try "boot helper" , the request tftp didn't come to my computer.
ServicesEngine boot-loader> boot helper
Loading tftp://192.168.1.4/cue-installer.sme.8.5.1 ...
ServicesEngine boot-loader>
Thank you for your help.

ISM-SRE-300-K9= bare bones loading Cisco Unity Express

Hello,
I am wondering if anyone knows whether or not I can load Cisco Unity Express on to a Bare Bones ISM-SRE-300-K9=. Does one need to buy it pre-configured from Factory, or does the Non Rehostable 2-Port License automatically install with the download from cisco.com
These are the conditions of the scenario:
1) ISM-SRE-300-K9= is bare bones from distribution
2) The unit has a Service Contract (SAU) purchased and attached
3) I will be installing the 5-Pack Mailbox License
4) I will be installing CUE 8.6 on to the unit from cisco.com download
Thanks,
Jordan

Hi Swati,
Even if there are other posts, you may check this link:
http://www.cisco.com/en/US/docs/routers/access/interfaces/software/feature/guide/ism-sm-sre.html
Also CUE is not supprted on the Embedded Service Module, so you have to install de CUE module on ISM 0/0 or 0/1
-HTH-
Jorge...
Sent from Cisco Technical Support Android App

ISM-SRE-300 - Lab Configuration

I'm using the ISM-SRE-300 for the Wireless LAN Controller solution. All our sites have a 2911 Router, and a 3750-x (3750x) Catalyst Switch with Routing enabled.
NOTE: This only covers the basic configuration of the networking side. If you set this up in a lab, you can follow other articles to install the Cisco Wireless LAN Controller software via FTP quite easily. Getting the basic infrastructure to work is the hard part.
Sometimes, a little help is all you need.
LAB ROUTER
Note: Some old-schoolers don't like VLAN(1) on the raw interface. They like to change it to a VLAN sub-interface.
interface GigabitEthernet0/1
description *** CONNECTS TO L3 SWITCH
no ip address
duplex auto
speed auto
interface GigabitEthernet0/1.1
encapsulation dot1Q 1 native
ip address 10.1.1.2 255.255.255.0
interface ISM0/0
ip unnumbered GigabitEthernet0/1.1
service-module ip address 10.1.1.10 255.255.255.0            (note: don't try to ping this IP. Won't respond. But it works!)
service-module ip default-gateway 10.1.1.2
interface ISM0/1
description *** MGF Interface (Handles switching for Router; Releives RTR CPU - This is cool. You should read up on this.)
switchport mode trunk
vlan 30
name WIFI_EMPLOYEES
vlan 40
name WIFI_GUESTS
interface Vlan1
ip address 55.1.0.1 255.255.255.0
interface Vlan30
ip address 55.30.0.1 255.255.0.0
ip helper-address 10.1.1.1
interface Vlan40
ip address 55.40.0.1 255.255.0.0
ip helper-address 10.1.1.1
router eigrp 1
network 10.1.1.0 0.0.0.255
network 55.1.0.0 0.0.0.255
network 55.30.0.0 0.0.0.255
network 55.40.0.0 0.0.0.255
ip route 10.1.1.10 255.255.255.255 ISM0/0               (very, very important!!!)
LAB SWITCH
ip routing
ip dhcp excluded-address 10.1.1.1 10.1.1.10
ip dhcp excluded-address 20.1.1.1 20.1.1.10
ip dhcp excluded-address 55.30.0.1 55.30.0.10
ip dhcp excluded-address 55.40.0.1 55.40.0.10
ip dhcp pool management
network 10.1.1.0 255.255.255.0
default-router 10.1.1.2
ip dhcp pool ap-pool
network 20.1.1.0 255.255.255.0
default-router 20.1.1.1
ip dhcp pool WiFi_Employees
network 55.30.0.0 255.255.255.0
default-router 55.30.0.1
ip dhcp pool WiFi_Guests
network 55.40.0.0 255.255.255.0
default-router 55.40.0.1
vlan 20
name AP_VLAN
interface GigabitEthernet1/0/10
description *** CONNECTS TO GIG0/1 on the ROUTER
switchport trunk encapsulation dot1q
switchport mode trunk
interface GigabitEthernet1/0/11
description *** CONNECTS TO YOUR AP (do not connect it yet until the end when your controller is up and ready to register the AP)
switchport access vlan 20
switchport mode access
interface Vlan1
ip address 10.1.1.1 255.255.255.0
interface Vlan20
description *** VLAN FOR APs        (assuming you want all the AP's on their own VLAN)
ip address 20.1.1.1 255.255.255.0
router eigrp 1
network 10.1.1.0 0.0.0.255
network 20.1.1.0 0.0.0.255
ip route 0.0.0.0 0.0.0.0 10.1.1.2
LAPTOP CONFIGURATION
FTP SERVER - Install the FTP software Cisco recommends. I used FILEZILLA. Worked fine on an XP laptop.
WLCM2 IMAGE - Download the WLCM2 ZIP file only. Do not download the AES by itself. Unzip the ZIP file and its contents to the FTP folder. The AES within THE ZIP file is what you refer to, not the AES that you can download separately!!!
FTP
MY PC was connected via CABLE to the 3750-X CATALYST switch that I'm using in the lab. It obtained a DHCP IP of 10.1.1.11.
FTP Command on Router:     service-module ism 0/0 install url ftp://[email protected]/AIR-SRE-K9-7.0.112.0.aes
(NOTE: Replace the name with whatever version you downloaded)
WIRELESS LAN CONTROLLER SETUP WIZARD RESPONSES
Term Auto-Install:     NO
Admin Name:     cisco
Admin PW:     cisco
Mgmt Interface:     55.1.0.2
Interface Sub:     255.255.255.0
Gateway:     55.1.0.1
VLAN:     0-Untagged
Interface:     1
DHCP Server:     10.1.1.1
Virtual IP:     1.1.1.1
Multicast:     239.255.1.60
Mobility RF:     LAB
SSID:     EMPLOYEES     (your VLAN 30)
DHCP Bridge:     NO
Allow Static:     YES
Radius:     NO
Country:     US
Enable 802.11b:     YES
Enable 802.11a:     YES
Enable 802.11g:     YES
Auto-RF:     YES
NTP:     NO
Config Correct?     YES
What's missing? (Assumption: You've set up controllers before and this stuff comes simple -- let me know otherwise)
- Option 43 in the DHCP Pool configurations. I just entered the CAPWAP command on the AP itself to point it to the Controller.
- Interfaces for EACH VLAN must be configured first before WLAN's
- When you configure the WLAN's, point it to the appropriate VLAN Interface you created.
Tony Ortiz
Network Administrator II
Golden Valley Health Centers (22 sites)

Just to be clear, this posting is NOT asking for help. This is a posting to help those with the HARDWARE side of the configuration. This is what I just finished doing in my lab for testing. Worked great. DHCP, WLAN Advertising, etc. I now have to go on to the next harder steps of really combing through the WLC configuration, applying our standard template configurations for our Routers/Switches, applying dual and tertiary redundancy with regards to routing, DHCP via MICROSOFT and not using a switch, and so on.
This was just meant to help those who don't have a lot of experience configuring the router switch environment. Sorry if I confused any one.

Installing CUE 8.6.7 on ISM-SRE-300-K9

Hello,
I been trying to install CUE on ISM0/0 but so far i havent been available...
My configuration goes as follow:
interface ISM0/0
ip unnumbered GigabitEthernet0/0.11
ip virtual-reassembly in
service-module fail-open
service-module ip address 130.11.1.3 255.255.0.0
service-module ip default-gateway 130.11.1.1
end
ip route 130.11.1.3 255.255.255.255 ISM0/0
till this point everything goes ok, i have connectivity between each of em...
then on ISM my config is
ServicesEngine boot-loader> show config
IP addr:                130.11.1.3
Netmask:                255.255.0.0
TFTP server :           130.11.1.1
GW IP addr:             130.11.1.1
Default Boot:           disk
Bootloader Version:     2.1.18
Bootloader Name:        bootloader
Default Helper-file:    /cue-installer.SPA.sme.8.6.7
Default bootloader:     secondary
however when i issue the boot helper command it goes on a cycle showing the next output
Loading tftp://130.11.1.1/cue-installer.SPA.sme.8.6.7 ... done.
Verifying ...
Corrupted netboot image detected
done.
Starting Kernel.
After this server reboot and it goes on cycling.
I have checked this guide so far, and i think im not missing a step.
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/unity_exp/rel8_6/install/CUE_86_install/boothelp.html
TYVM

Sure can, here are my outputs
-------Show Ver--------
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.3(2)T, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Thu 28-Mar-13 11:05 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M16, RELEASE SOFTWARE (fc1)
RTR_V_CPACK uptime is 15 hours, 30 minutes
System returned to ROM by reload at 19:31:49 CUU Mon Apr 14 2014
System image file is "flash0:c2900-universalk9-mz.SPA.153-2.T.bin"
Last reload type: Normal Reload
Last reload reason: Reload Command
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco CISCO2921/K9 (revision 1.0) with 1523712K/49152K bytes of memory.
Processor board ID FTX1749AJ5G
4 Gigabit Ethernet interfaces
2 terminal lines
1 Channelized E1/PRI port
6 Voice FXO interfaces
1 Internal Services Module (ISM) with Services Ready Engine (SRE)
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
License Info:
License UDI:
Device#   PID                   SN
*0        CISCO2921/K9          FTX1749AJ5G
Technology Package License Information for Module:'c2900'
Technology    Technology-package           Technology-package
              Current       Type           Next reboot
ipbase        ipbasek9      Permanent      ipbasek9
security      None          None           None
uc            uck9          Permanent      uck9
data          None          None           None
Configuration register is 0x2102
------------Show diag--------------------
Slot 0:
        C2921 Mother board 3GE, integrated VPN and 4W Port adapter, 10 ports
        Port adapter is analyzed
        Port adapter insertion time 15:30:43 ago
        EEPROM contents at hardware discovery:
        PCB Serial Number        : FOC17420KBG
        Hardware Revision        : 1.0
        Part Number              : 73-11835-11
        Top Assy. Part Number    : 800-30794-07
        Board Revision           : A0
        Deviation Number         : 130603
        Fab Version              : 03
        Product (FRU) Number     : CISCO2921/K9
        Version Identifier       : V08
        CLEI Code                : CMMHS10ARB
        Processor type           : C2
        Chassis Serial Number    : FTX1749AJ5G
        Chassis MAC Address      : 78da.6e82.b600
        MAC Address block size   : 80
        Manufacturing Test Data : 00 00 00 00 00 00 00 00
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF C1 8B 46 4F 43 31 37 34 32 30 4B 42 47 40
          0x10: 06 16 41 01 00 82 49 2E 3B 0B C0 46 03 20 00 78
          0x20: 4A 07 42 41 30 88 00 01 FE 2B 02 03 CB 8C 43 49
          0x30: 53 43 4F 32 39 32 31 2F 4B 39 89 56 30 38 20 D9
          0x40: 04 40 C1 CB C2 C6 8A 43 4D 4D 48 53 31 30 41 52
          0x50: 42 09 C2 C2 8B 46 54 58 31 37 34 39 41 4A 35 47
          0x60: C3 06 78 DA 6E 82 B6 00 43 00 50 C4 08 00 00 00
          0x70: 00 00 00 00 00 F3 00 03 40 01 63 FF FF FF FF FF
          0x80: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x90: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0xA0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0xB0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0xC0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0xD0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0xE0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0xF0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
        Internal Power Supply information
        Top Assy. Part Number    : 341-0226-03
        Deviation Number         : 0
        PCB Serial Number        : DCA1738K05Q
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        Version Identifier       : V03
        Product (FRU) Number     : PWR-2921-51-AC
        CLEI Code                : 0000000000
        Board Revision           : A0
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF 40 05 E2 DF 45 01 55 00 E2 03 88 00 00 00
          0x10: 00 C1 8B 44 43 41 31 37 33 38 4B 30 35 51 03 00
          0x20: 81 00 00 00 00 04 00 89 56 30 33 20 CB 8E 50 57
          0x30: 52 2D 32 39 32 31 2D 35 31 2D 41 43 C6 8A 30 30
          0x40: 30 30 30 30 30 30 30 30 F3 00 59 41 01 22 42 00
          0x50: 05 F8 00 50 01 F3 18 3B 02 F0 19 D9 03 E8 1B 76
          0x60: 04 E2 1C 49 05 D9 1D 1B 06 D8 1D ED 07 CF 1E BF
          0x70: 08 CE 1F 40 09 C2 1F B8 0A B8 20 34 0B B7 20 B0
          0x80: 0D AF 21 0C 0F 9F 21 67 11 91 21 94 13 87 21 C0
          0x90: 17 6E 21 DB 1B 57 21 EA 1F 3F 21 E2 23 28 21 D4
          0xA0: 27 0A 21 CD 42 41 30 FF FF FF FF FF FF FF FF FF
          0xB0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0xC0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0xD0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0xE0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0xF0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
        PVDM Slot 0:
        64-channel (G.711) Voice/Fax PVDM3 DSP DIMM PVDM daughter card
        Hardware Revision        : 1.0
        Part Number              : 73-11809-03
        Board Revision           : D0
        Deviation Number         : 0
        Fab Version              : 03
        PCB Serial Number        : FOC17453K9V
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        Processor type           : 00
        Product (FRU) Number     : PVDM3-64
        Version Identifier       : V01
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF 40 05 DB 41 01 00 82 49 2E 21 03 42 44 30
          0x10: 88 00 00 00 00 02 03 C1 8B 46 4F 43 31 37 34 35
          0x20: 33 4B 39 56 03 00 81 00 00 00 00 04 00 09 00 CB
          0x30: 8F 50 56 44 4D 33 2D 36 34 20 20 20 20 20 20 20
          0x40: 89 56 30 31 20 D9 02 40 C1 FF FF FF FF FF FF FF
          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
        WIC Slot 0:
        VWIC3-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1
        Hardware Revision        : 1.0
        Top Assy. Part Number    : 800-34657-01
        Part Number              : 73-13419-01
        Board Revision           : B0
        Deviation Number         : 0
        Fab Version              : 05
        PCB Serial Number        : FOC1745429E
        Version Identifier       : V01
        Product (FRU) Number     : VWIC3-1MFT-T1/E1
        CLEI Code                : COUIA7PCAA
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF 40 06 ED 41 01 00 C0 46 03 20 00 87 61 01
          0x10: 82 49 34 6B 01 42 42 30 88 00 00 00 00 02 05 C1
          0x20: 8B 46 4F 43 31 37 34 35 34 32 39 45 89 56 30 31
          0x30: 20 CB 90 56 57 49 43 33 2D 31 4D 46 54 2D 54 31
          0x40: 2F 45 31 C6 8A 43 4F 55 49 41 37 50 43 41 41 03
          0x50: 00 81 00 00 00 00 04 00 D9 03 40 C1 CB FF FF FF
          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
        WIC Slot 1:
        2nd generation - FXO Voice daughter card (4 port)
        Hardware Revision        : 5.0
        Top Assy. Part Number    : 800-33585-01
        Board Revision           : E0
        Deviation Number         : 0-0
        Fab Version              : 04
        PCB Serial Number        : FOC174279XY
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        Product (FRU) Number     : VIC2-4FXO
        Version Identifier       : V04
        CLEI Code                : CNUIAXJAAC
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF 40 00 4C 41 05 00 C0 46 03 20 00 83 31 01
          0x10: 42 45 30 80 00 00 00 00 02 04 C1 8B 46 4F 43 31
          0x20: 37 34 32 37 39 58 59 03 00 81 00 00 00 00 04 00
          0x30: CB 89 56 49 43 32 2D 34 46 58 4F 89 56 30 34 20
          0x40: C6 8A 43 4E 55 49 41 58 4A 41 41 43 FF FF FF FF
          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
        WIC Slot 2:
        2nd generation - FXO Voice daughter card (2 port)
        Hardware Revision        : 5.0
        Top Assy. Part Number    : 800-33584-01
        Board Revision           : E0
        Deviation Number         : 0-0
        Fab Version              : 04
        PCB Serial Number        : FOC1745AP4H
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        Product (FRU) Number     : VIC2-2FXO
        Version Identifier       : V03
        CLEI Code                : CNUIARTAAC
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF 40 00 4D 41 05 00 C0 46 03 20 00 83 30 01
          0x10: 42 45 30 80 00 00 00 00 02 04 C1 8B 46 4F 43 31
          0x20: 37 34 35 41 50 34 48 03 00 81 00 00 00 00 04 00
          0x30: CB 89 56 49 43 32 2D 32 46 58 4F 89 56 30 33 20
          0x40: C6 8A 43 4E 55 49 41 52 54 41 41 43 FF FF FF FF
          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Internal Services Module (ISM) Slot 0
        Internal Services Module with Services Ready Engine
        Internal Services Module is analyzed
        Internal Services Module insertion time 15:30:43 ago
        EEPROM contents at hardware discovery:
        PCB Serial Number        : FOC174782WY
        Hardware Revision        : 1.0
        Part Number              : 73-13417-01
        Top Assy. Part Number    : 800-34577-01
        Deviation Number         : 0
        Fab Version              : 04
        Board Revision           : A0
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        CLEI Code                : IPUCAXHBAB
        Product (FRU) Number     : ISM-SRE-300-K9
        Version Identifier       : V02
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF C1 8B 46 4F 43 31 37 34 37 38 32 57 59 40
          0x10: 06 31 41 01 00 82 49 34 69 01 C0 46 03 20 00 87
          0x20: 11 01 88 00 00 00 00 02 04 42 41 30 03 00 81 00
          0x30: 00 00 00 04 00 C6 8A 49 50 55 43 41 58 48 42 41
          0x40: 42 CB 8E 49 53 4D 2D 53 52 45 2D 33 30 30 2D 4B
          0x50: 39 89 56 30 32 20 D9 03 40 C1 CB F3 00 06 40 05
          0x60: F3 43 00 16 FF FF FF FF FF FF FF FF FF FF FF FF
          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Embedded Service Engine 0/0 :
Total platform memory : 1572864K bytes
Total 2nd core memory : 0K bytes
Start of physical address for 2nd core : 0x80000000
Virtual address start of 2nd core memory : 0x0 - 0x0
2nd core configured disabled
L2 cache ways for 2nd core : 0
-------------------------Show Inv-------------------------------------
RTR_V_CPACK#sh inv
NAME: "CISCO2921/K9", DESCR: "CISCO2921/K9 chassis, Hw Serial#: FTX1749AJ5G, Hw Revision: 1.0"
PID: CISCO2921/K9      , VID: V08 , SN: FTX1749AJ5G
NAME: "VWIC3-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0", DESCR: "VWIC3-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC3-1MFT-T1/E1 , VID: V01 , SN: FOC1745429E
NAME: "2nd generation four port FXO voice interface daughtercard on Slot 0 SubSlot 1", DESCR: "2nd generation four port FXO voice interface daughtercard"
PID: VIC2-4FXO         , VID: V04 , SN: FOC174279XY
NAME: "2nd generation two port FXO voice interface daughtercard on Slot 0 SubSlot 2", DESCR: "2nd generation two port FXO voice interface daughtercard"
PID: VIC2-2FXO         , VID: V03 , SN: FOC1745AP4H
NAME: "PVDM3 DSP DIMM with 64 Channels on Slot 0 SubSlot 4", DESCR: "PVDM3 DSP DIMM with 64 Channels"
PID: PVDM3-64          , VID: V01 , SN: FOC17453K9V
NAME: "Internal Services Module with Services Ready Engine on Slot 0", DESCR: "Internal Services Module with Services Ready Engine"
PID: ISM-SRE-300-K9    , VID: V02 , SN: FOC174782WY
NAME: "C2921/C2951 AC Power Supply", DESCR: "C2921/C2951 AC Power Supply"
PID: PWR-2921-51-AC    , VID: V03 , SN: DCA1738K05Q
TYVM

2911 ISM-SRE-300 CUE 8.6.7 install failure...Verifying ... Invalid signature in command line file !!

ISM-SRE-300 seems to be a loop at boot with Verifying ... Invalid signature in command line file
Any ideas?
Log
Install of ftp://*****:*****@10.100.64.21/cue-vm-k9.SPA.sme.8.6.7.pkg in progress
Install status : Waiting for RBIP registration
No localstore
2911#
[Resuming connection 1 to 10.102.66.254 ... ]
Initializing memory. Please wait...
Memory initialization OK. Continue...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
SRE step 2 - SM requests key file info...
SRE step 3 - SM stores registration info...
SRE configuration keeps the same. No flash update needed!
SRE step 4 - SM downloads key-file...
Writing keyfile to flash Size 891
writing complete.
Updating flash with bootloader configuration.
Please wait .................. done.
SRE step 5 - SM requests installer info...
SRE step 6 - SM stores installer info...
Updating flash with bootloader configuration.
Please wait .................. done.
SRE step 7 - SM now downloads installer
done.
SRE step 8 - SM requests tcl header file info...
SRE step 9 - SM now downloads the tcl header file
TCL header file downloaded completely size: 691
SRE step 10 - SM requests tcl file info...
SRE step 11 - SM now downloads the tcl file
TCL file downloaded completely size: 38933
SRE step 12 - SM now boots Installer
Verifying ... done.
Starting Kernel.
Platform: ism
INIT: version 2.86 booting
mounting proc fs ...
mounting sys fs ...
mounting /dev/shm tmpfs ...
kernel.sem = 1900 4000 32 100
vm.overcommit_memory = 1
vm.min_free_kbytes = 8192
                Welcome to Cisco Service Engine
Setting the system time from hardware clock
********** rc.aesop ****************
Populating resource values from /etc/ism_rsrc_file
Populating resource values from /etc/default_rsrc_file
Populating resource values from /etc/products/cue/default_rsrc_file
Populating resource values from /etc/products/cue/ism_rsrc_file
==> Management interface is eth0
==> Management interface is eth0
IOS IP Address Registration complete.
Kernel IP routing table
Destination     Gateway         Genmask         Flags   MSS Window irtt Iface
10.102.66.0    *               255.255.255.0   U         0 0          0 eth0
default         142.102.66.254 0.0.0.0         UG        0 0          0 eth0
Size of buff is: 65536
65536 bytes written
Valid License file not found: Using default values
INIT: Entering runlevel: 2
********** rc.post_install ****************
Changing owners and file permissions.
INIT: Switching to runlevel: 4
INIT: Sending processes the TERM signal
STARTED: dwnldr_startup.sh
sre_type= 1
        Welcome to Cisco Systems Service Engine Helper Software
Downloading ftp cue-vm-k9.SPA.sme.8.6.7.pkg
Bytes downloaded : 727736
Validating package signature ... done
- Parsing package manifest files... complete.
No installed manifests found.
- Checking Package dependencies... complete.
Downloading ftp cue-vm-langpack.sme.8.6.7.pkg
Error: Download error
Can not download cue-vm-langpack.sme.8.6.7.pkg
error code 550 : error type 'Can not ▒
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor              1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor              1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor              1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor              1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor              1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor              1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor              1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...

ISM-SRE-300 seems to be a loop at boot with Verifying ... Invalid signature in command line file
Any ideas?
Log
Install of ftp://*****:*****@10.100.64.21/cue-vm-k9.SPA.sme.8.6.7.pkg in progress
Install status : Waiting for RBIP registration
No localstore
2911#
[Resuming connection 1 to 10.102.66.254 ... ]
Initializing memory. Please wait...
Memory initialization OK. Continue...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
SRE step 2 - SM requests key file info...
SRE step 3 - SM stores registration info...
SRE configuration keeps the same. No flash update needed!
SRE step 4 - SM downloads key-file...
Writing keyfile to flash Size 891
writing complete.
Updating flash with bootloader configuration.
Please wait .................. done.
SRE step 5 - SM requests installer info...
SRE step 6 - SM stores installer info...
Updating flash with bootloader configuration.
Please wait .................. done.
SRE step 7 - SM now downloads installer
done.
SRE step 8 - SM requests tcl header file info...
SRE step 9 - SM now downloads the tcl header file
TCL header file downloaded completely size: 691
SRE step 10 - SM requests tcl file info...
SRE step 11 - SM now downloads the tcl file
TCL file downloaded completely size: 38933
SRE step 12 - SM now boots Installer
Verifying ... done.
Starting Kernel.
Platform: ism
INIT: version 2.86 booting
mounting proc fs ...
mounting sys fs ...
mounting /dev/shm tmpfs ...
kernel.sem = 1900 4000 32 100
vm.overcommit_memory = 1
vm.min_free_kbytes = 8192
                Welcome to Cisco Service Engine
Setting the system time from hardware clock
********** rc.aesop ****************
Populating resource values from /etc/ism_rsrc_file
Populating resource values from /etc/default_rsrc_file
Populating resource values from /etc/products/cue/default_rsrc_file
Populating resource values from /etc/products/cue/ism_rsrc_file
==> Management interface is eth0
==> Management interface is eth0
IOS IP Address Registration complete.
Kernel IP routing table
Destination     Gateway         Genmask         Flags   MSS Window irtt Iface
10.102.66.0    *               255.255.255.0   U         0 0          0 eth0
default         142.102.66.254 0.0.0.0         UG        0 0          0 eth0
Size of buff is: 65536
65536 bytes written
Valid License file not found: Using default values
INIT: Entering runlevel: 2
********** rc.post_install ****************
Changing owners and file permissions.
INIT: Switching to runlevel: 4
INIT: Sending processes the TERM signal
STARTED: dwnldr_startup.sh
sre_type= 1
        Welcome to Cisco Systems Service Engine Helper Software
Downloading ftp cue-vm-k9.SPA.sme.8.6.7.pkg
Bytes downloaded : 727736
Validating package signature ... done
- Parsing package manifest files... complete.
No installed manifests found.
- Checking Package dependencies... complete.
Downloading ftp cue-vm-langpack.sme.8.6.7.pkg
Error: Download error
Can not download cue-vm-langpack.sme.8.6.7.pkg
error code 550 : error type 'Can not ▒
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor              1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor              1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor              1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor              1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor              1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor              1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor              1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...

ISM-SRE-300-K9 Failed

Hello
Im installing a CUCME + CUE, after the instalation of the ISM-SRE-300-K9 in 2921
i configure the module but in show commands it appears as failed, and i cannot access the service module.
IOS : c2900-universalk9-mz.SPA.151-4.M2
CUCME: 8.6
CUE Module: ISM-SRE-300-K9
This message appears on the console:
%SRE_SM-6-STATE_CHANGE: ISM0/0 changing state from SERVICE_MODULE_STATE_SHDN to SERVICE_MODULE_STATE_FAIL
CUE Config on CUCME
interface ISM0/0
ip unnumbered G0/0
service-module ip address 176.16.1.7 255.255.255.0
service-module ip default-gateway 176.16.1.1
no keepalive
ip route 176.16.1.7 255.255.255.255 ISM0/0
dial-peer voice 8100 voip
mailbox-selection orig-called-num
description ------------------------------[CUE]
destination-pattern 80..
session protocol sipv2
session target ipv4:176.16.1.7
dtmf-relay sip-notify
codec g711ulaw
no vad
telephony-service
voicemail 8000
Logs:
%SRE_SM-6-STATE_CHANGE: ISM0/0 changing state from SERVICE_MODULE_STATE_SHDN to SERVICE_MODULE_STATE_FAIL
GW01#service-module iSM 0/0 status
Service Module is Cisco ISM0/0
Service Module supports session via TTY line 131
Service Module is failed
Service Module heartbeat-reset is enabled
Service Module is in fail open
Service Module status is not available
No install/uninstall in progress
Local Partition Info
=====================
Please reset module to retrieve
partition information if needed
Somebody can help me?
Thanks

Did u eventually got this running, I too have the same problem.
I am unable to configure the SRE-300-K9, always i have to reset and go to the int ism0/0 and give no shut to bring it up but it comes up in boot loader configuration.
I tried to install using the guide but after all installation and language selection it keeps saying as payload missing and curl code error 19 and sometimes curl code error 78.
If u already found some solutions pls share it.

Can't launch Cisco Configuration Professional on Windows Vista x64

The Help is necessary to resole the issue (see subject).
Tech enveronment
Windows Vista x64
Adobe Reader X ver. 10.1.0 (Russian)
Cisco Configuration Professional 2.5
JRE 6 update 27
JRE 6 update 27 (64-bit)
Internet Explorer 9.0.8112.16421IS
While launch CCP popup the message box :
"Unable to read the resource file. The file could be corrupted. Please re-install Cisco Configuration Professional to resolve the issue."
Ones (never popup after) Popup the message box (InstallShield Wizard):
Adode Reader is not present on the PC. It is required to view the PDF file.
Also the message box InstallShield Wizard:
Internet Explorer with javaplug-in version 1.6.0_11   Cheked
Adobe Flash Player version 10                              Cheked
Memory 1 Gb                                                      Cheked
Screen Resolution 1024x768                                Cheked
Cuted _cpinstaller_004.log file:
Product : Cisco Configuration Professional version 1.0
10-4-2011 16:48:31 LOG   : Command line options =
10-4-2011 16:48:31 LOG   : GetOS: OS Windows Vista
10-4-2011 16:48:31 LOG   : GetOSServicePack: service pack 2
10-4-2011 16:48:31 LOG   : GetIEVersion: IE version 9.0.8112.16421
10-4-2011 16:52:51 LOG   : CheckCCPPorts: WARNING 80 is not a registered HTTP port
10-4-2011 16:53:27 ERROR : SetRunAsAdmin: ERROR REG_APP_COMBAT_LAYERS_ROOT could not be created.
10-4-2011 16:53:46 LOG   : GetJavaIEPluginVersion: java IE plugin version 1.6.0_27
10-4-2011 16:53:47 LOG   : GetFlashPlayerVersion: flash player version 10
10-4-2011 16:53:47 LOG   : GetScreenResolution: screen resolution 8
10-4-2011 16:54:14 LOG   : OpenPDFFile: Adobe reader could not be found on system.
10-4-2011 16:56:17 LOG   : OnEnd: installation successfully completed.

Hi,ngoldwat!
Yes, off cource, I've tried to launch CCP with Administartor rights - no success.
I have re-installed CCP under Local Admin and launched it. Great!!! It works! But, one of but, the app does not launch from domain user while I use Run as Administrator. I think the issue in the permission and/or user's profile.
Thanks ngoldwat! You have helped me.

Setting up Easy VPN in Cisco Configuration Professional, external access problems!

Hi
I have a Cisco 857 router which is flashed with Cisco Configuration Express 2.6.
Cisco Configuration Professional 2.6 is installed on my PC and I'm trying to configure Easy VPN for access away from the office.
The steps I have taken are as follows:
1) I launched the Easy VPN Server Wizard
2) IP address of Virtual Tunnel Interface is unnumbered to Vlan1 from the drop down menu - Authentication, Pre Shared Key
3) IKE Proposals set to the default option thats already there
4) Transform set is the default which is already there
5) Method list for group policy Lookup is LOCAL
6) User authentication is LOCAL ONLY, the admin account shows up in ADD USER CREDENTIALS which is the account i'm going to test the connection with
7) I have set up a GROUP POLICY which i've named, created a PRE SHARED KEY, created an IP address pool & subnet mask to the same range as the routers addresses and left all other options to default
8) I left cTCP unticked and disabled
9) I delivered the commands succesfully
10) I click TEST VPN SERVER and get 3 ticks successful for Server configuration, dependant components & Firewall
11) I open the cisco client and access the VPN internally using the routers LAN address, it prompts for my user name and password, I type it in and connect successfully
12) When I go home I configure my client to the same settings except I change the LAN address for the external WAN ip address, but I get an error message which says "Secure VPN Connection terminated locally by the client. Reason 412: The remote peer is no longer responding"
VPN Client settings are as follows
Group Authentication
Enable Transparent Tunneling- IPSec over UDP (NAT / PAT)
Currently I have a dynamic external IP address, I intend to get a static one once I know I can get this to work.
I would be extremely greatful if someone could help me solve this issue and work out why I can't connect externally.
I have no knowledge of CLI but will use it if given some instructions.
Thanks.
P.S. I have turned off all antivirus and firewall programs on the client computer when trying to connect.

Your nat exemption acl is backwards...
access-list 101 permit ip 192.168.2.0 255.255.255.0 192.168.1.0 255.255.255.0
should be...
access-list 101 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0

Where to find package language for ISM-SRE-300-k9 CUE 8.6.1

Hi,
I need to add a new language package in ISM-SRE-300-K9. Currently it has CUE Voicemail European Spanish (Spanish language pack) (8.6.1) but I need
Spanish Mexican.
I have read the procedure to add additional package but I can't find the package cue-vm-langpack.ise.8.6.1. pkg , I have just found
the file cue-vm-es_MX-langpack.ise.8.6.1.prt1.
any of you know where I can find the package I need?
regards

Paolo,
I have tried to install the package in ISM-SRE-300-K9 but I received an error mesage.
I have already load all the file in ftp server folder , I have tried with anonymous user and not anonymous but fail
do you know the reason of this error??
CUE# software install add cue-vm-langpack.ise.8.6.1.pkg
WARNING:: This command will install the necessary software to
WARNING:: complete an add-on install. It is recommended that a backup be done
WARNING:: before installing software.
Would you like to continue?[confirm]
Downloading ftp cue-vm-langpack.ise.8.6.1.pkg
Bytes downloaded : 1385425
Validating package signature ...
ERROR get_pkg_list:Package signature validation failed for cue-vm-langpack.ise.8.6.1.pkg
Package signature validation failed for cue-vm-langpack.ise.8.6.1.pkg
CUE#

ISM-SRE-300-K9

Hi ,
Can anybody help me to solve the following error , while installing new ISM-SRE-300-K9 unity express module .
Available commands are:
# - enter the number for the language to select one
r # - remove the language for given #
i # - more information about the language for given #
x - Done with language selection
Enter Command:3
Language Installation Menu:
# Selected SKU Language Name (version)
1 ITA CUE Voicemail Italian (8.6.1)
2 ESP CUE Voicemail European Spanish (8.6.1)
3 * ENU CUE Voicemail US English (8.6.1)
4 FRA CUE Voicemail European French (8.6.1)
5 ESO CUE Voicemail Latin American Spanish (8.6.1)
6 ESM CUE Voicemail Mexican Spanish (8.6.1)
7 ARA CUE Voicemail Arabic (8.6.1)
8 NLD CUE Voicemail Dutch (8.6.1)
9 SVE CUE Voicemail Swedish (8.6.1)
10 NOR CUE Voicemail Norwegian (8.6.1)
11 FRC CUE Voicemail Canadian French (8.6.1)
12 PTG CUE Voicemail Portuguese (8.6.1)
13 TUR CUE Voicemail Turkish (8.6.1)
14 HUN CUE Voicemail Hungarian (8.6.1)
15 ENG CUE Voicemail UK English (8.6.1)
16 DEU CUE Voicemail German (8.6.1)
17 HBR CUE Voicemail Hebrew (8.6.1)
18 DAN CUE Voicemail Danish (8.6.1)
19 PTB CUE Voicemail Brazilian Portuguese (8.6.1)
20 CHT CUE Voicemail Traditional Chinese (Taiwan) (8.6.1)
21 KOR CUE Voicemail Korean (8.6.1)
22 CHS CUE Voicemail Simplified Chinese (PRC) (8.6.1)
23 JPN CUE Voicemail Japanese (8.6.1)
24 ZHH CUE Voicemail Hong Kong Chinese (8.6.1)
25 RUS CUE Voicemail Russian (8.6.1)
Available commands are:
# - enter the number for the language to select one
r # - remove the language for given #
i # - more information about the language for given #
x - Done with language selection
Enter Command:x
ui_install scripts executed successfully.
Starting payload download
File transfer error during download. Curl error code is 78
Error: Error encountered while downloading payload(s)
Error encountered while downloading payload(s)
Unable to install. Please try again
Please select from the following
1 Install software
2 Reload module
3 Disk cleanup
4 Install License(s)
(Type '?' at any time for help)
Choice:

Hi,
This error indicates that you are missing a language installation file, please download it from the same directory (version of CUE) and try the installation.
HTH
Manish

Can Cisco Configuration Professional to use IPS feature ?

Dear Expert
Hello.
Could you tell me about Cisco Configuration Professional.
I'd like to try the IOS-IPS on Cisco2901-SEC/K9.
I was search in CCO about Cisco Configuration Professional.
The Cisco2901-SEC/K9 does not support SDM.
But, The Cisco2901-SEC/K9 supported the Cisco Configuration Professional.
Can Cisco Configuration Professional to use IPS feature like SDM?
Regards,
Takuro.

Hi,
yes, you can configure IOS IPS from Cisco Configuration Professional.
CCP has a wizard to guide you through the process, this is a link for that :
http://www.cisco.com/en/US/prod/collateral/iosswrel/ps6537/ps6586/ps6634/prod_white_paper0900aecd8066d265.html
i hope this helps you.
Mashal

Installing ISM-SRE-300-K9

We initially planned to install our Call Manager and then install our remote locations. Given that scenario, the vendor sold us SRST Routers with no voicemail capability since the plan was to have the voicemail centralized. Well, that plan has changed and we have to get 3 remote locations up and running with voicemail before the actual Call Manager is up and running. We order 3 ISM-SRE Modules to go in our 2921 routers for the locations.
When I try to create a session on the ISM and I login, all it does is constantlly reboot looking for an image. I am assuming that Unity Express needs to be installed? I have worked with the type of modules before, but they already had software on them. This is new territory for me and I am under the gun to get these up and running. Can someone guide me on what I need to install and how? We have been running CUE 8.5 at the other sites.
Please help

Hi James,
Can you try
http://www.cisco.com/en/US/docs/voice_ip_comm/unity_exp/rel8_5/install/installsre.pdf
Cheers!
Rob

SG 300 and Cisco Configuration Assistant

Hi guys I'm having trouble in connecting a SG 300 switch with CCA v3.2. I have already connected the switch with CCA, however I can't see anything in my CCA's Front Panel and Topology view.
Here is the view of my Front Panel view after I connect the switch :
Could you guys please help me to find what the problem is?
Thanks a lot!

Hi Robert,,
Thanks for your reply. I found out that the problem was caused by the firmware, just like what you said.
I have upgraded the firmware, and now the switch is able to connect properly.

ISM-SRE-300-K9 & Cisco Configuration Professional Issue

Similar Messages

Maybe you are looking for