ISM-SRE-300-K9 Failed
Hello
Im installing a CUCME + CUE, after the instalation of the ISM-SRE-300-K9 in 2921
i configure the module but in show commands it appears as failed, and i cannot access the service module.
IOS : c2900-universalk9-mz.SPA.151-4.M2
CUCME: 8.6
CUE Module: ISM-SRE-300-K9
This message appears on the console:
%SRE_SM-6-STATE_CHANGE: ISM0/0 changing state from SERVICE_MODULE_STATE_SHDN to SERVICE_MODULE_STATE_FAIL
CUE Config on CUCME
interface ISM0/0
ip unnumbered G0/0
service-module ip address 176.16.1.7 255.255.255.0
service-module ip default-gateway 176.16.1.1
no keepalive
ip route 176.16.1.7 255.255.255.255 ISM0/0
dial-peer voice 8100 voip
mailbox-selection orig-called-num
description ------------------------------[CUE]
destination-pattern 80..
session protocol sipv2
session target ipv4:176.16.1.7
dtmf-relay sip-notify
codec g711ulaw
no vad
telephony-service
voicemail 8000
Logs:
%SRE_SM-6-STATE_CHANGE: ISM0/0 changing state from SERVICE_MODULE_STATE_SHDN to SERVICE_MODULE_STATE_FAIL
GW01#service-module iSM 0/0 status
Service Module is Cisco ISM0/0
Service Module supports session via TTY line 131
Service Module is failed
Service Module heartbeat-reset is enabled
Service Module is in fail open
Service Module status is not available
No install/uninstall in progress
Local Partition Info
=====================
Please reset module to retrieve
partition information if needed
Somebody can help me?
Thanks
Did u eventually got this running, I too have the same problem.
I am unable to configure the SRE-300-K9, always i have to reset and go to the int ism0/0 and give no shut to bring it up but it comes up in boot loader configuration.
I tried to install using the guide but after all installation and language selection it keeps saying as payload missing and curl code error 19 and sometimes curl code error 78.
If u already found some solutions pls share it.
Similar Messages
-
Where to find package language for ISM-SRE-300-k9 CUE 8.6.1
Hi,
I need to add a new language package in ISM-SRE-300-K9. Currently it has CUE Voicemail European Spanish (Spanish language pack) (8.6.1) but I need
Spanish Mexican.
I have read the procedure to add additional package but I can't find the package cue-vm-langpack.ise.8.6.1. pkg , I have just found
the file cue-vm-es_MX-langpack.ise.8.6.1.prt1.
any of you know where I can find the package I need?
regardsPaolo,
I have tried to install the package in ISM-SRE-300-K9 but I received an error mesage.
I have already load all the file in ftp server folder , I have tried with anonymous user and not anonymous but fail
do you know the reason of this error??
CUE# software install add cue-vm-langpack.ise.8.6.1.pkg
WARNING:: This command will install the necessary software to
WARNING:: complete an add-on install. It is recommended that a backup be done
WARNING:: before installing software.
Would you like to continue?[confirm]
Downloading ftp cue-vm-langpack.ise.8.6.1.pkg
Bytes downloaded : 1385425
Validating package signature ...
ERROR get_pkg_list:Package signature validation failed for cue-vm-langpack.ise.8.6.1.pkg
Package signature validation failed for cue-vm-langpack.ise.8.6.1.pkg
CUE# -
Cisco 2901-CME-SRST and ISM-SRE-300-K9 No Package already installed?
Good Morning Everybody,
I'm installing a new CME router with CUE.
But, the ISM-SRE-300-K9 is empty, I don't if it's normal.
I try to install two different packages :
Version 8.5.1
cue-installer.sme.8.5.1
cue-vm-full-k9.sme.8.5.1.prt1
cue-vm-installer-k9.sme.8.5.1.prt1
cue-vm-k9.sme.8.5.1.key
cue-vm-k9.sme.8.5.1.pkg
cue-vm-k9.sme.8.5.1.pkg.install.sre
cue-vm-k9.sme.8.5.1.pkg.install.sre.header
cue-vm-langpack.sme.8.5.1.pkg
Version 8.6.1
cue-installer.SPA.sme.8.6.1
cue-vm-full-k9.SPA.sme.8.6.1.prt1
cue-vm-installer-k9.SPA.sme.8.6.1.prt1
cue-vm-k9.SPA.sme.8.6.1.key
cue-vm-k9.SPA.sme.8.6.1.pkg
cue-vm-k9.SPA.sme.8.6.1.pkg.install.sre
cue-vm-k9.SPA.sme.8.6.1.pkg.install.sre.header
cue-vm-langpack.sme.8.6.1.pkg
Without success...
I try with two differents FTP server (Linux and Windows), connection and session seems ok with Wireshark, but, module go to loop, without installation success.
Different try :
Version 8.5.1
==========
Router#$0 status
Service Module is Cisco ISM0/0
Service Module supports session via TTY line 67
Service Module is trying to recover from error
Service Module heartbeat-reset is enabled
Service Module is in fail open
Service Module status is not available
Module resource information:
CPU Frequency: 1068 MHz
Memory Size: 493 MB
Disk 0 Size: 4110 MB
Install of ftp://*****:*****@10.10.80.68/Downloads/cue-vm-k9.sme.8.5.1.pkg in progress
Install status : Waiting for file request
Local Partition Info - (0 apps)
=====================
Retrieving partition information
Router#
Feb 16 06:04:22.583: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:29:03.839: %SYS-5-CONFIG_I: Configured from console by vty0 (10.10.80.68)
Feb 16 06:29:19.915: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:30:01.283: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:30:21.711: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:30:42.143: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:31:02.571: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:31:22.995: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP Registration Request
Feb 16 06:31:22.999: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:31:43.419: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:32:03.843: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:32:45.275: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:33:05.699: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:33:26.119: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:33:46.543: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:34:06.979: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP Registration Request
Feb 16 06:34:06.983: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:34:27.399: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:34:47.831: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:35:29.263: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:35:49.687: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:36:10.119: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:36:30.563: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:36:50.983: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP Registration Request
Feb 16 06:36:50.987: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:37:11.467: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:37:31.887: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:38:13.399: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:38:33.815: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Feb 16 06:38:54.243: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File RequestConnection closed by foreign host.
Version 8.6.1
==========
Router#[email protected]/Downloads/cue-vm-k9.SPA.sme.8.6.1.pkg
Proceed with installation? [no]: yes
Feb 16 07:16:21.235: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP Registration Request
Loading Downloads/cue-vm-k9.SPA.sme.8.6.1.pkg.install.sre !
[OK - 38648/4096 bytes]
No local store partition
Following languages are available for installation.
# SKU Language Code Language Name
1 ARA ar_SA CUE Voicemail Arabic
2 DAN da_DK CUE Voicemail Danish
3 DEU de_DE CUE Voicemail German
4 ENG en_GB CUE Voicemail UK English
5 ENU en_US CUE Voicemail US English
6 ESO es_CO CUE Voicemail Latin American Spanish
7 ESP es_ES CUE Voicemail European Spanish
8 ESM es_MX CUE Voicemail Mexican Spanish
9 FRC fr_CA CUE Voicemail Canadian French
10 FRA fr_FR CUE Voicemail European French
11 HUN hu_HU CUE Voicemail Hungarian
12 ITA it_IT CUE Voicemail Italian
13 HBR iw_IL CUE Voicemail Hebrew
14 JPN ja_JP CUE Voicemail Japanese
15 KOR ko_KR CUE Voicemail Korean
16 NLD nl_NL CUE Voicemail Dutch
17 NOR no_NO CUE Voicemail Norwegian
18 PTB pt_BR CUE Voicemail Brazilian Portuguese
19 PTG pt_PT CUE Voicemail Portuguese
20 RUS ru_RU CUE Voicemail Russian
21 SVE sv_SE CUE Voicemail Swedish
22 TUR tr_TR CUE Voicemail Turkish
23 CHS zh_CN CUE Voicemail Simplified Chinese (PRC)
24 ZHH zh_HK CUE Voicemail Hong Kong Chinese
25 CHT zh_TW CUE Voicemail Traditional Chinese (Taiwan)
You can install upto 5 language(s) on this platform.
Please select the language(s) you want to install by entering the language number(s)
Languages can be entered as comma separated or space separated list
Example: 1,3 would select 'CUE Voicemail Arabic' and 'CUE Voicemail German'
Enter languages:4
Following languages will be installed on the system:
CUE Voicemail UK English
Do you want to continue with the selected options?(y/n):y
Router#
Feb 16 07:16:50.579: %SM_INSTALL-6-INST_RESET: ISM0/0 is reset for software installation.
Feb 16 07:17:11.235: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP Registration Request
Feb 16 07:17:11.239: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
===========================
on the service-module ism0/0 session
===========================
Initializing memory. Please wait...
Memory initialization OK. Continue...
Feb 16 07:25:08.683: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Primary Boot Loader Authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
SRE step 2 - SM requests key file info...
!!! Opcode Error - Get a wrong RBIP frame !!!
Feb 16 07:25:29.259: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP Registration Request
Feb 16 07:25:29.263: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Time-out from RBIP response wait loop
SRE step 3 - SM stores registration info...
Updating flash with bootloader configuration.
Please wait .............. done.
SRE step 4 - SM downloads key-file...
!!! Opcode Error - Get a wrong RBIP frame !!!
Writing keyfile to flash Size 891
writing complete.
SRE step 5 - SM requests installer info...
Feb 16 07:25:49.791: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
SRE step 6 - SM stores installer info...
Updating flash with bootloader configuration.
Please wait .............. done.
SRE step 7 - SM now downloads installer
|
!!! Opcode Error - Get a wrong RBIP frame !!!
Feb 16 07:26:10.343: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Requestdone.
SRE step 8 - SM requests tcl header file info...
!!! Opcode Error - Get a wrong RBIP frame !!!
Feb 16 07:26:52.919: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Time-out from RBIP response wait loop
SRE step 9 - SM now downloads the tcl header file
|
!!! Opcode Error - Get a wrong RBIP frame !!!
TCL header file downloaded completely size: 691
SRE step 10 - SM requests tcl file info...
Feb 16 07:27:13.467: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File Request
Time-out from RBIP response wait loop
SRE step 11 - SM now downloads the tcl file
!!! Opcode Error - Get a wrong RBIP frame !!!
Feb 16 07:27:34.011: %SM_INSTALL-6-INST_RBIP: ISM0/0 received msg: RBIP File RequestTCL file downloaded completely size: 691
SRE step 12 - SM now boots Installer
Verifying ...
Corrupted netboot image detected
done.
Starting Kernel.
loop ....
I have no idea to solve my problem...
If anybody have suggestion, should be great.
Have a nice day !
Thanks
FabHi,
I try that. From this guide :
http://www.cisco.com/en/US/docs/voice_ip_comm/unity_exp/rel3_0/installation/guide/upg3boot.pdf
with windows xp tftpd32
computer config : 192.168.1.4/24
ftp server 192.168.1.3 /24
Router int g0/0 192.168.1.1 255.255.255.0 + ip route 192.168.1.2 255.255.255.255 ism 0/0
ISM :
ServicesEngine boot-loader> show config
IP addr: 192.168.1.2
Netmask: 255.255.255.0
TFTP server : 192.168.1.4
GW IP addr: 192.168.1.1
Default Boot: disk
Bootloader Version: 2.1.18
Bootloader Name: bootloader
Default Helper-file: cue-installer.sme.8.5.1
Default bootloader: primary
From Computer :
C:\Documents and Settings\f>ping 192.168.1.2 -t
Pinging 192.168.1.2 with 32 bytes of data:
Reply from 192.168.1.2: bytes=32 time<1ms TTL=126
Icmp from ism to computer: no response.
from ism to router int g0/0 : no response too.
router to ism (boot-loader): ok
pc to ism (boot-loader) : ok
So when I try "boot helper" , the request tftp didn't come to my computer.
ServicesEngine boot-loader> boot helper
Loading tftp://192.168.1.4/cue-installer.sme.8.5.1 ...
ServicesEngine boot-loader>
Thank you for your help. -
Installing CUE 8.6.7 on ISM-SRE-300-K9
Hello,
I been trying to install CUE on ISM0/0 but so far i havent been available...
My configuration goes as follow:
interface ISM0/0
ip unnumbered GigabitEthernet0/0.11
ip virtual-reassembly in
service-module fail-open
service-module ip address 130.11.1.3 255.255.0.0
service-module ip default-gateway 130.11.1.1
end
ip route 130.11.1.3 255.255.255.255 ISM0/0
till this point everything goes ok, i have connectivity between each of em...
then on ISM my config is
ServicesEngine boot-loader> show config
IP addr: 130.11.1.3
Netmask: 255.255.0.0
TFTP server : 130.11.1.1
GW IP addr: 130.11.1.1
Default Boot: disk
Bootloader Version: 2.1.18
Bootloader Name: bootloader
Default Helper-file: /cue-installer.SPA.sme.8.6.7
Default bootloader: secondary
however when i issue the boot helper command it goes on a cycle showing the next output
Loading tftp://130.11.1.1/cue-installer.SPA.sme.8.6.7 ... done.
Verifying ...
Corrupted netboot image detected
done.
Starting Kernel.
After this server reboot and it goes on cycling.
I have checked this guide so far, and i think im not missing a step.
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/unity_exp/rel8_6/install/CUE_86_install/boothelp.html
TYVMSure can, here are my outputs
-------Show Ver--------
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.3(2)T, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Thu 28-Mar-13 11:05 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M16, RELEASE SOFTWARE (fc1)
RTR_V_CPACK uptime is 15 hours, 30 minutes
System returned to ROM by reload at 19:31:49 CUU Mon Apr 14 2014
System image file is "flash0:c2900-universalk9-mz.SPA.153-2.T.bin"
Last reload type: Normal Reload
Last reload reason: Reload Command
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco CISCO2921/K9 (revision 1.0) with 1523712K/49152K bytes of memory.
Processor board ID FTX1749AJ5G
4 Gigabit Ethernet interfaces
2 terminal lines
1 Channelized E1/PRI port
6 Voice FXO interfaces
1 Internal Services Module (ISM) with Services Ready Engine (SRE)
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
License Info:
License UDI:
Device# PID SN
*0 CISCO2921/K9 FTX1749AJ5G
Technology Package License Information for Module:'c2900'
Technology Technology-package Technology-package
Current Type Next reboot
ipbase ipbasek9 Permanent ipbasek9
security None None None
uc uck9 Permanent uck9
data None None None
Configuration register is 0x2102
------------Show diag--------------------
Slot 0:
C2921 Mother board 3GE, integrated VPN and 4W Port adapter, 10 ports
Port adapter is analyzed
Port adapter insertion time 15:30:43 ago
EEPROM contents at hardware discovery:
PCB Serial Number : FOC17420KBG
Hardware Revision : 1.0
Part Number : 73-11835-11
Top Assy. Part Number : 800-30794-07
Board Revision : A0
Deviation Number : 130603
Fab Version : 03
Product (FRU) Number : CISCO2921/K9
Version Identifier : V08
CLEI Code : CMMHS10ARB
Processor type : C2
Chassis Serial Number : FTX1749AJ5G
Chassis MAC Address : 78da.6e82.b600
MAC Address block size : 80
Manufacturing Test Data : 00 00 00 00 00 00 00 00
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF C1 8B 46 4F 43 31 37 34 32 30 4B 42 47 40
0x10: 06 16 41 01 00 82 49 2E 3B 0B C0 46 03 20 00 78
0x20: 4A 07 42 41 30 88 00 01 FE 2B 02 03 CB 8C 43 49
0x30: 53 43 4F 32 39 32 31 2F 4B 39 89 56 30 38 20 D9
0x40: 04 40 C1 CB C2 C6 8A 43 4D 4D 48 53 31 30 41 52
0x50: 42 09 C2 C2 8B 46 54 58 31 37 34 39 41 4A 35 47
0x60: C3 06 78 DA 6E 82 B6 00 43 00 50 C4 08 00 00 00
0x70: 00 00 00 00 00 F3 00 03 40 01 63 FF FF FF FF FF
0x80: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x90: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xA0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xB0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xC0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xD0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xE0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xF0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Internal Power Supply information
Top Assy. Part Number : 341-0226-03
Deviation Number : 0
PCB Serial Number : DCA1738K05Q
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Version Identifier : V03
Product (FRU) Number : PWR-2921-51-AC
CLEI Code : 0000000000
Board Revision : A0
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 05 E2 DF 45 01 55 00 E2 03 88 00 00 00
0x10: 00 C1 8B 44 43 41 31 37 33 38 4B 30 35 51 03 00
0x20: 81 00 00 00 00 04 00 89 56 30 33 20 CB 8E 50 57
0x30: 52 2D 32 39 32 31 2D 35 31 2D 41 43 C6 8A 30 30
0x40: 30 30 30 30 30 30 30 30 F3 00 59 41 01 22 42 00
0x50: 05 F8 00 50 01 F3 18 3B 02 F0 19 D9 03 E8 1B 76
0x60: 04 E2 1C 49 05 D9 1D 1B 06 D8 1D ED 07 CF 1E BF
0x70: 08 CE 1F 40 09 C2 1F B8 0A B8 20 34 0B B7 20 B0
0x80: 0D AF 21 0C 0F 9F 21 67 11 91 21 94 13 87 21 C0
0x90: 17 6E 21 DB 1B 57 21 EA 1F 3F 21 E2 23 28 21 D4
0xA0: 27 0A 21 CD 42 41 30 FF FF FF FF FF FF FF FF FF
0xB0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xC0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xD0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xE0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xF0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
PVDM Slot 0:
64-channel (G.711) Voice/Fax PVDM3 DSP DIMM PVDM daughter card
Hardware Revision : 1.0
Part Number : 73-11809-03
Board Revision : D0
Deviation Number : 0
Fab Version : 03
PCB Serial Number : FOC17453K9V
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 00
Product (FRU) Number : PVDM3-64
Version Identifier : V01
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 05 DB 41 01 00 82 49 2E 21 03 42 44 30
0x10: 88 00 00 00 00 02 03 C1 8B 46 4F 43 31 37 34 35
0x20: 33 4B 39 56 03 00 81 00 00 00 00 04 00 09 00 CB
0x30: 8F 50 56 44 4D 33 2D 36 34 20 20 20 20 20 20 20
0x40: 89 56 30 31 20 D9 02 40 C1 FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC Slot 0:
VWIC3-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1
Hardware Revision : 1.0
Top Assy. Part Number : 800-34657-01
Part Number : 73-13419-01
Board Revision : B0
Deviation Number : 0
Fab Version : 05
PCB Serial Number : FOC1745429E
Version Identifier : V01
Product (FRU) Number : VWIC3-1MFT-T1/E1
CLEI Code : COUIA7PCAA
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 06 ED 41 01 00 C0 46 03 20 00 87 61 01
0x10: 82 49 34 6B 01 42 42 30 88 00 00 00 00 02 05 C1
0x20: 8B 46 4F 43 31 37 34 35 34 32 39 45 89 56 30 31
0x30: 20 CB 90 56 57 49 43 33 2D 31 4D 46 54 2D 54 31
0x40: 2F 45 31 C6 8A 43 4F 55 49 41 37 50 43 41 41 03
0x50: 00 81 00 00 00 00 04 00 D9 03 40 C1 CB FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC Slot 1:
2nd generation - FXO Voice daughter card (4 port)
Hardware Revision : 5.0
Top Assy. Part Number : 800-33585-01
Board Revision : E0
Deviation Number : 0-0
Fab Version : 04
PCB Serial Number : FOC174279XY
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : VIC2-4FXO
Version Identifier : V04
CLEI Code : CNUIAXJAAC
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 00 4C 41 05 00 C0 46 03 20 00 83 31 01
0x10: 42 45 30 80 00 00 00 00 02 04 C1 8B 46 4F 43 31
0x20: 37 34 32 37 39 58 59 03 00 81 00 00 00 00 04 00
0x30: CB 89 56 49 43 32 2D 34 46 58 4F 89 56 30 34 20
0x40: C6 8A 43 4E 55 49 41 58 4A 41 41 43 FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC Slot 2:
2nd generation - FXO Voice daughter card (2 port)
Hardware Revision : 5.0
Top Assy. Part Number : 800-33584-01
Board Revision : E0
Deviation Number : 0-0
Fab Version : 04
PCB Serial Number : FOC1745AP4H
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : VIC2-2FXO
Version Identifier : V03
CLEI Code : CNUIARTAAC
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 00 4D 41 05 00 C0 46 03 20 00 83 30 01
0x10: 42 45 30 80 00 00 00 00 02 04 C1 8B 46 4F 43 31
0x20: 37 34 35 41 50 34 48 03 00 81 00 00 00 00 04 00
0x30: CB 89 56 49 43 32 2D 32 46 58 4F 89 56 30 33 20
0x40: C6 8A 43 4E 55 49 41 52 54 41 41 43 FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Internal Services Module (ISM) Slot 0
Internal Services Module with Services Ready Engine
Internal Services Module is analyzed
Internal Services Module insertion time 15:30:43 ago
EEPROM contents at hardware discovery:
PCB Serial Number : FOC174782WY
Hardware Revision : 1.0
Part Number : 73-13417-01
Top Assy. Part Number : 800-34577-01
Deviation Number : 0
Fab Version : 04
Board Revision : A0
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
CLEI Code : IPUCAXHBAB
Product (FRU) Number : ISM-SRE-300-K9
Version Identifier : V02
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF C1 8B 46 4F 43 31 37 34 37 38 32 57 59 40
0x10: 06 31 41 01 00 82 49 34 69 01 C0 46 03 20 00 87
0x20: 11 01 88 00 00 00 00 02 04 42 41 30 03 00 81 00
0x30: 00 00 00 04 00 C6 8A 49 50 55 43 41 58 48 42 41
0x40: 42 CB 8E 49 53 4D 2D 53 52 45 2D 33 30 30 2D 4B
0x50: 39 89 56 30 32 20 D9 03 40 C1 CB F3 00 06 40 05
0x60: F3 43 00 16 FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Embedded Service Engine 0/0 :
Total platform memory : 1572864K bytes
Total 2nd core memory : 0K bytes
Start of physical address for 2nd core : 0x80000000
Virtual address start of 2nd core memory : 0x0 - 0x0
2nd core configured disabled
L2 cache ways for 2nd core : 0
-------------------------Show Inv-------------------------------------
RTR_V_CPACK#sh inv
NAME: "CISCO2921/K9", DESCR: "CISCO2921/K9 chassis, Hw Serial#: FTX1749AJ5G, Hw Revision: 1.0"
PID: CISCO2921/K9 , VID: V08 , SN: FTX1749AJ5G
NAME: "VWIC3-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0", DESCR: "VWIC3-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC3-1MFT-T1/E1 , VID: V01 , SN: FOC1745429E
NAME: "2nd generation four port FXO voice interface daughtercard on Slot 0 SubSlot 1", DESCR: "2nd generation four port FXO voice interface daughtercard"
PID: VIC2-4FXO , VID: V04 , SN: FOC174279XY
NAME: "2nd generation two port FXO voice interface daughtercard on Slot 0 SubSlot 2", DESCR: "2nd generation two port FXO voice interface daughtercard"
PID: VIC2-2FXO , VID: V03 , SN: FOC1745AP4H
NAME: "PVDM3 DSP DIMM with 64 Channels on Slot 0 SubSlot 4", DESCR: "PVDM3 DSP DIMM with 64 Channels"
PID: PVDM3-64 , VID: V01 , SN: FOC17453K9V
NAME: "Internal Services Module with Services Ready Engine on Slot 0", DESCR: "Internal Services Module with Services Ready Engine"
PID: ISM-SRE-300-K9 , VID: V02 , SN: FOC174782WY
NAME: "C2921/C2951 AC Power Supply", DESCR: "C2921/C2951 AC Power Supply"
PID: PWR-2921-51-AC , VID: V03 , SN: DCA1738K05Q
TYVM -
ISM-SRE-300-K9 & Cisco Configuration Professional Issue
hi there,
i have a cisco 2901 router running CME 8.6 the router has a ISM-SRE-300-K9 card init with Unity Express 8.0.5 installed.
i am having issues with Cisco configuration professional and configuring the module
under module configuration the status is "module is not reachable", if i click on details i get further information "unable to execute command from the module. module is either reloading or is in failed state. you must make the module up and refresh the module"
i have tried reloading, resetting and refreshing the module but the issue is still present
i have accessed the module from the CLI set it in offline mode and factory defaulted it and the same issue is still present
the only thing i can think is that this is a bug with CCP as the loopback interface which the module is using can be pinged fine from the router so the message makes no sense.
any ideasIs you problem with CCP or the module itself ?
Because, CCP bugs and limitations aside, the module can be normally be installed, configured and managed using CLI or its web interface (after software is initially loaded). -
ISM-SRE-300 seems to be a loop at boot with Verifying ... Invalid signature in command line file
Any ideas?
Log
Install of ftp://*****:*****@10.100.64.21/cue-vm-k9.SPA.sme.8.6.7.pkg in progress
Install status : Waiting for RBIP registration
No localstore
2911#
[Resuming connection 1 to 10.102.66.254 ... ]
Initializing memory. Please wait...
Memory initialization OK. Continue...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
SRE step 2 - SM requests key file info...
SRE step 3 - SM stores registration info...
SRE configuration keeps the same. No flash update needed!
SRE step 4 - SM downloads key-file...
Writing keyfile to flash Size 891
writing complete.
Updating flash with bootloader configuration.
Please wait .................. done.
SRE step 5 - SM requests installer info...
SRE step 6 - SM stores installer info...
Updating flash with bootloader configuration.
Please wait .................. done.
SRE step 7 - SM now downloads installer
done.
SRE step 8 - SM requests tcl header file info...
SRE step 9 - SM now downloads the tcl header file
TCL header file downloaded completely size: 691
SRE step 10 - SM requests tcl file info...
SRE step 11 - SM now downloads the tcl file
TCL file downloaded completely size: 38933
SRE step 12 - SM now boots Installer
Verifying ... done.
Starting Kernel.
Platform: ism
INIT: version 2.86 booting
mounting proc fs ...
mounting sys fs ...
mounting /dev/shm tmpfs ...
kernel.sem = 1900 4000 32 100
vm.overcommit_memory = 1
vm.min_free_kbytes = 8192
Welcome to Cisco Service Engine
Setting the system time from hardware clock
********** rc.aesop ****************
Populating resource values from /etc/ism_rsrc_file
Populating resource values from /etc/default_rsrc_file
Populating resource values from /etc/products/cue/default_rsrc_file
Populating resource values from /etc/products/cue/ism_rsrc_file
==> Management interface is eth0
==> Management interface is eth0
IOS IP Address Registration complete.
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
10.102.66.0 * 255.255.255.0 U 0 0 0 eth0
default 142.102.66.254 0.0.0.0 UG 0 0 0 eth0
Size of buff is: 65536
65536 bytes written
Valid License file not found: Using default values
INIT: Entering runlevel: 2
********** rc.post_install ****************
Changing owners and file permissions.
INIT: Switching to runlevel: 4
INIT: Sending processes the TERM signal
STARTED: dwnldr_startup.sh
sre_type= 1
Welcome to Cisco Systems Service Engine Helper Software
Downloading ftp cue-vm-k9.SPA.sme.8.6.7.pkg
Bytes downloaded : 727736
Validating package signature ... done
- Parsing package manifest files... complete.
No installed manifests found.
- Checking Package dependencies... complete.
Downloading ftp cue-vm-langpack.sme.8.6.7.pkg
Error: Download error
Can not download cue-vm-langpack.sme.8.6.7.pkg
error code 550 : error type 'Can not ▒
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...ISM-SRE-300 seems to be a loop at boot with Verifying ... Invalid signature in command line file
Any ideas?
Log
Install of ftp://*****:*****@10.100.64.21/cue-vm-k9.SPA.sme.8.6.7.pkg in progress
Install status : Waiting for RBIP registration
No localstore
2911#
[Resuming connection 1 to 10.102.66.254 ... ]
Initializing memory. Please wait...
Memory initialization OK. Continue...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
SRE step 2 - SM requests key file info...
SRE step 3 - SM stores registration info...
SRE configuration keeps the same. No flash update needed!
SRE step 4 - SM downloads key-file...
Writing keyfile to flash Size 891
writing complete.
Updating flash with bootloader configuration.
Please wait .................. done.
SRE step 5 - SM requests installer info...
SRE step 6 - SM stores installer info...
Updating flash with bootloader configuration.
Please wait .................. done.
SRE step 7 - SM now downloads installer
done.
SRE step 8 - SM requests tcl header file info...
SRE step 9 - SM now downloads the tcl header file
TCL header file downloaded completely size: 691
SRE step 10 - SM requests tcl file info...
SRE step 11 - SM now downloads the tcl file
TCL file downloaded completely size: 38933
SRE step 12 - SM now boots Installer
Verifying ... done.
Starting Kernel.
Platform: ism
INIT: version 2.86 booting
mounting proc fs ...
mounting sys fs ...
mounting /dev/shm tmpfs ...
kernel.sem = 1900 4000 32 100
vm.overcommit_memory = 1
vm.min_free_kbytes = 8192
Welcome to Cisco Service Engine
Setting the system time from hardware clock
********** rc.aesop ****************
Populating resource values from /etc/ism_rsrc_file
Populating resource values from /etc/default_rsrc_file
Populating resource values from /etc/products/cue/default_rsrc_file
Populating resource values from /etc/products/cue/ism_rsrc_file
==> Management interface is eth0
==> Management interface is eth0
IOS IP Address Registration complete.
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
10.102.66.0 * 255.255.255.0 U 0 0 0 eth0
default 142.102.66.254 0.0.0.0 UG 0 0 0 eth0
Size of buff is: 65536
65536 bytes written
Valid License file not found: Using default values
INIT: Entering runlevel: 2
********** rc.post_install ****************
Changing owners and file permissions.
INIT: Switching to runlevel: 4
INIT: Sending processes the TERM signal
STARTED: dwnldr_startup.sh
sre_type= 1
Welcome to Cisco Systems Service Engine Helper Software
Downloading ftp cue-vm-k9.SPA.sme.8.6.7.pkg
Bytes downloaded : 727736
Validating package signature ... done
- Parsing package manifest files... complete.
No installed manifests found.
- Checking Package dependencies... complete.
Downloading ftp cue-vm-langpack.sme.8.6.7.pkg
Error: Download error
Can not download cue-vm-langpack.sme.8.6.7.pkg
error code 550 : error type 'Can not ▒
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting...
Authenticating boot loader....
Secondary Boot Loader authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialze network device
Backup current platform configurations....
SRE step 1 - SM registration...
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait .................. done.
Loading disk:/bzImage ... Loading disk:/cmdlineextra ... done.
Verifying ... Invalid signature in command line file !!
Corrupted command line detected
done.
Starting Kernel.
Initializing memory. Please wait...
Memory initialization OK. Continue...
DDR Memory 0512 MB detected
Genuine Intel(R) processor 1.06GHz
BIOS ISM 2.6, BIOS Build date: 10/16/2009
System now booting... -
Hi ,
Can anybody help me to solve the following error , while installing new ISM-SRE-300-K9 unity express module .
Available commands are:
# - enter the number for the language to select one
r # - remove the language for given #
i # - more information about the language for given #
x - Done with language selection
Enter Command:3
Language Installation Menu:
# Selected SKU Language Name (version)
1 ITA CUE Voicemail Italian (8.6.1)
2 ESP CUE Voicemail European Spanish (8.6.1)
3 * ENU CUE Voicemail US English (8.6.1)
4 FRA CUE Voicemail European French (8.6.1)
5 ESO CUE Voicemail Latin American Spanish (8.6.1)
6 ESM CUE Voicemail Mexican Spanish (8.6.1)
7 ARA CUE Voicemail Arabic (8.6.1)
8 NLD CUE Voicemail Dutch (8.6.1)
9 SVE CUE Voicemail Swedish (8.6.1)
10 NOR CUE Voicemail Norwegian (8.6.1)
11 FRC CUE Voicemail Canadian French (8.6.1)
12 PTG CUE Voicemail Portuguese (8.6.1)
13 TUR CUE Voicemail Turkish (8.6.1)
14 HUN CUE Voicemail Hungarian (8.6.1)
15 ENG CUE Voicemail UK English (8.6.1)
16 DEU CUE Voicemail German (8.6.1)
17 HBR CUE Voicemail Hebrew (8.6.1)
18 DAN CUE Voicemail Danish (8.6.1)
19 PTB CUE Voicemail Brazilian Portuguese (8.6.1)
20 CHT CUE Voicemail Traditional Chinese (Taiwan) (8.6.1)
21 KOR CUE Voicemail Korean (8.6.1)
22 CHS CUE Voicemail Simplified Chinese (PRC) (8.6.1)
23 JPN CUE Voicemail Japanese (8.6.1)
24 ZHH CUE Voicemail Hong Kong Chinese (8.6.1)
25 RUS CUE Voicemail Russian (8.6.1)
Available commands are:
# - enter the number for the language to select one
r # - remove the language for given #
i # - more information about the language for given #
x - Done with language selection
Enter Command:x
ui_install scripts executed successfully.
Starting payload download
File transfer error during download. Curl error code is 78
Error: Error encountered while downloading payload(s)
Error encountered while downloading payload(s)
Unable to install. Please try again
Please select from the following
1 Install software
2 Reload module
3 Disk cleanup
4 Install License(s)
(Type '?' at any time for help)
Choice:Hi,
This error indicates that you are missing a language installation file, please download it from the same directory (version of CUE) and try the installation.
HTH
Manish -
ISM-SRE-300-K9= bare bones loading Cisco Unity Express
Hello,
I am wondering if anyone knows whether or not I can load Cisco Unity Express on to a Bare Bones ISM-SRE-300-K9=. Does one need to buy it pre-configured from Factory, or does the Non Rehostable 2-Port License automatically install with the download from cisco.com
These are the conditions of the scenario:
1) ISM-SRE-300-K9= is bare bones from distribution
2) The unit has a Service Contract (SAU) purchased and attached
3) I will be installing the 5-Pack Mailbox License
4) I will be installing CUE 8.6 on to the unit from cisco.com download
Thanks,
JordanHi Swati,
Even if there are other posts, you may check this link:
http://www.cisco.com/en/US/docs/routers/access/interfaces/software/feature/guide/ism-sm-sre.html
Also CUE is not supprted on the Embedded Service Module, so you have to install de CUE module on ISM 0/0 or 0/1
-HTH-
Jorge...
Sent from Cisco Technical Support Android App -
ISM-SRE-300 don´t allow send data between clients and pc in LAN
I have an ISM-SRE-300 on cisco 1941 does not allow sending of data between clients attached to an AP wired to PC Networking.
LAN CLIENT= VLAN 20 10.94.4.0 /24
SERVER CLIENTE = 10.94.4.1 D.G= 10.94.4.254
ROUTER
INT G0/0.1= IP UNNUMBERED VLAN 1 NATIVE VLAN
INT G 0/0.20 = IP UNNUMBERED VLAN 20
INT VLAN 1 = 94.4.1.1 /24
INT VLAN 20 = 10.94.4.254 /24
ISM-SRE
MANAGEMENT UNTAGGED 94.4.1.2
VLAN 20 VLAN=20 IP=10.94.4.251 /24 D.G. 10.94.4.254
IF SENDING PING FROM ROUTER TO SERVER=10.94.4.1 IS OK
IF SENDING PING FROM ISM TO SERVER DON´T ANSWER
IF JOIN A CLIENT IN AP, CLIENT WIRELESS=10.94.4.150 /24 D.G. 10.94.4.254
I SEND PING TO ISM 10.94.4.251 IS OK
I SENG PING TO ROUTER 10.94.4.254 DON´T ANSWER
I SEND PING FROM SERVER (10.94.4.1) TO ROUTER 10.94.4.254 IS OK
I SEND PING TO ISM 10.94.4.251 DON´T WORK
I SENG PING TO CLIENT WIRELESS 10.94.4.150 DON´T WORK
CAN ANYONE HELP ME ?
THANKS
JUAN-RAMONJust to be clear, this posting is NOT asking for help. This is a posting to help those with the HARDWARE side of the configuration. This is what I just finished doing in my lab for testing. Worked great. DHCP, WLAN Advertising, etc. I now have to go on to the next harder steps of really combing through the WLC configuration, applying our standard template configurations for our Routers/Switches, applying dual and tertiary redundancy with regards to routing, DHCP via MICROSOFT and not using a switch, and so on.
This was just meant to help those who don't have a lot of experience configuring the router switch environment. Sorry if I confused any one. -
ISM-SRE-300 - Lab Configuration
I'm using the ISM-SRE-300 for the Wireless LAN Controller solution. All our sites have a 2911 Router, and a 3750-x (3750x) Catalyst Switch with Routing enabled.
NOTE: This only covers the basic configuration of the networking side. If you set this up in a lab, you can follow other articles to install the Cisco Wireless LAN Controller software via FTP quite easily. Getting the basic infrastructure to work is the hard part.
Sometimes, a little help is all you need.
LAB ROUTER
Note: Some old-schoolers don't like VLAN(1) on the raw interface. They like to change it to a VLAN sub-interface.
interface GigabitEthernet0/1
description *** CONNECTS TO L3 SWITCH
no ip address
duplex auto
speed auto
interface GigabitEthernet0/1.1
encapsulation dot1Q 1 native
ip address 10.1.1.2 255.255.255.0
interface ISM0/0
ip unnumbered GigabitEthernet0/1.1
service-module ip address 10.1.1.10 255.255.255.0 (note: don't try to ping this IP. Won't respond. But it works!)
service-module ip default-gateway 10.1.1.2
interface ISM0/1
description *** MGF Interface (Handles switching for Router; Releives RTR CPU - This is cool. You should read up on this.)
switchport mode trunk
vlan 30
name WIFI_EMPLOYEES
vlan 40
name WIFI_GUESTS
interface Vlan1
ip address 55.1.0.1 255.255.255.0
interface Vlan30
ip address 55.30.0.1 255.255.0.0
ip helper-address 10.1.1.1
interface Vlan40
ip address 55.40.0.1 255.255.0.0
ip helper-address 10.1.1.1
router eigrp 1
network 10.1.1.0 0.0.0.255
network 55.1.0.0 0.0.0.255
network 55.30.0.0 0.0.0.255
network 55.40.0.0 0.0.0.255
ip route 10.1.1.10 255.255.255.255 ISM0/0 (very, very important!!!)
LAB SWITCH
ip routing
ip dhcp excluded-address 10.1.1.1 10.1.1.10
ip dhcp excluded-address 20.1.1.1 20.1.1.10
ip dhcp excluded-address 55.30.0.1 55.30.0.10
ip dhcp excluded-address 55.40.0.1 55.40.0.10
ip dhcp pool management
network 10.1.1.0 255.255.255.0
default-router 10.1.1.2
ip dhcp pool ap-pool
network 20.1.1.0 255.255.255.0
default-router 20.1.1.1
ip dhcp pool WiFi_Employees
network 55.30.0.0 255.255.255.0
default-router 55.30.0.1
ip dhcp pool WiFi_Guests
network 55.40.0.0 255.255.255.0
default-router 55.40.0.1
vlan 20
name AP_VLAN
interface GigabitEthernet1/0/10
description *** CONNECTS TO GIG0/1 on the ROUTER
switchport trunk encapsulation dot1q
switchport mode trunk
interface GigabitEthernet1/0/11
description *** CONNECTS TO YOUR AP (do not connect it yet until the end when your controller is up and ready to register the AP)
switchport access vlan 20
switchport mode access
interface Vlan1
ip address 10.1.1.1 255.255.255.0
interface Vlan20
description *** VLAN FOR APs (assuming you want all the AP's on their own VLAN)
ip address 20.1.1.1 255.255.255.0
router eigrp 1
network 10.1.1.0 0.0.0.255
network 20.1.1.0 0.0.0.255
ip route 0.0.0.0 0.0.0.0 10.1.1.2
LAPTOP CONFIGURATION
FTP SERVER - Install the FTP software Cisco recommends. I used FILEZILLA. Worked fine on an XP laptop.
WLCM2 IMAGE - Download the WLCM2 ZIP file only. Do not download the AES by itself. Unzip the ZIP file and its contents to the FTP folder. The AES within THE ZIP file is what you refer to, not the AES that you can download separately!!!
FTP
MY PC was connected via CABLE to the 3750-X CATALYST switch that I'm using in the lab. It obtained a DHCP IP of 10.1.1.11.
FTP Command on Router: service-module ism 0/0 install url ftp://[email protected]/AIR-SRE-K9-7.0.112.0.aes
(NOTE: Replace the name with whatever version you downloaded)
WIRELESS LAN CONTROLLER SETUP WIZARD RESPONSES
Term Auto-Install: NO
Admin Name: cisco
Admin PW: cisco
Mgmt Interface: 55.1.0.2
Interface Sub: 255.255.255.0
Gateway: 55.1.0.1
VLAN: 0-Untagged
Interface: 1
DHCP Server: 10.1.1.1
Virtual IP: 1.1.1.1
Multicast: 239.255.1.60
Mobility RF: LAB
SSID: EMPLOYEES (your VLAN 30)
DHCP Bridge: NO
Allow Static: YES
Radius: NO
Country: US
Enable 802.11b: YES
Enable 802.11a: YES
Enable 802.11g: YES
Auto-RF: YES
NTP: NO
Config Correct? YES
What's missing? (Assumption: You've set up controllers before and this stuff comes simple -- let me know otherwise)
- Option 43 in the DHCP Pool configurations. I just entered the CAPWAP command on the AP itself to point it to the Controller.
- Interfaces for EACH VLAN must be configured first before WLAN's
- When you configure the WLAN's, point it to the appropriate VLAN Interface you created.
Tony Ortiz
Network Administrator II
Golden Valley Health Centers (22 sites)Just to be clear, this posting is NOT asking for help. This is a posting to help those with the HARDWARE side of the configuration. This is what I just finished doing in my lab for testing. Worked great. DHCP, WLAN Advertising, etc. I now have to go on to the next harder steps of really combing through the WLC configuration, applying our standard template configurations for our Routers/Switches, applying dual and tertiary redundancy with regards to routing, DHCP via MICROSOFT and not using a switch, and so on.
This was just meant to help those who don't have a lot of experience configuring the router switch environment. Sorry if I confused any one. -
We initially planned to install our Call Manager and then install our remote locations. Given that scenario, the vendor sold us SRST Routers with no voicemail capability since the plan was to have the voicemail centralized. Well, that plan has changed and we have to get 3 remote locations up and running with voicemail before the actual Call Manager is up and running. We order 3 ISM-SRE Modules to go in our 2921 routers for the locations.
When I try to create a session on the ISM and I login, all it does is constantlly reboot looking for an image. I am assuming that Unity Express needs to be installed? I have worked with the type of modules before, but they already had software on them. This is new territory for me and I am under the gun to get these up and running. Can someone guide me on what I need to install and how? We have been running CUE 8.5 at the other sites.
Please helpHi James,
Can you try
http://www.cisco.com/en/US/docs/voice_ip_comm/unity_exp/rel8_5/install/installsre.pdf
Cheers!
Rob -
ISM-SRE CUE license registration- chassis or module serial number ?
I'm registering a license type L-FL-CUE-MBX-5= for a Cisco Unity Express 8.5.1 system on a ISM-SRE-300-K9
The license registration page is asking for a serial number. Is this the Chassis Serial or the Module Serial number?
ThanksYou do need but the module serial number; as the license installation is done on the actual Unity Express module.
cheers
Emmanuel -
Sf-300 48port failing 802.1x reauthentication and not re-initialising ports
Hi,
I have an issue with the sf-300 switch model, which i am depolying in lapsafe trolleys. The approach is to wake the laptops from the guest VLAN (20) with WOL have them authenticate with 802.1x and use DVA to put the ports in VLAN14 so updates can be pushed to them over night.
I have configured 802.1x, guest vlan and DVA which works initially, all host wake from WOL, the laptops successfully authenticate and are assigned to the VLAN (14). This remains stable for a time then the hosts fail reauthentication. I have also noticed that when a host is disconnected from a port and patched into another port the initial port remains in the authenticated state and the new port authenticates the client but the hostnames are missing on the 'authenticated hosts' page of the GUI, DVA fails. The ports display a port-failure message for a time then moves to failed reauthentication.
The only way I can get it to work again is to reboot the box. From the logs I can see the macs of laptops being rejected and I can also see attribute 26 being ignored. See log below. I am unsure as to why host are initially authenticated but reauthentication fails, is it not the same process?.
I have 11 of these switches and have configured 6 which all display the same behaviour. These switches are not CISCO I do not understand why they have badged them. The protocols/standards are implemented differently. If you incuded 'general ports' as an answer in a CISCO exam you would fail. There are also other issues I have noticed with these boxes, I am not impressed!!!.
Kind Regards
Daniel2147483217 2011-May-12 12:44:15 Informational %AAA-I-CONNECT: New http connection for user wayne, source 10.163.102.24 destination 10.167.152.131 ACCEPTED
2147483218 2011-May-12 12:39:31 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483219 2011-May-12 12:36:46 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483220 2011-May-12 12:22:12 Informational %AAA-I-DISCONNECT: http connection for user wayne, source 10.163.102.24 destination 10.167.152.131 TERMINATED
2147483221 2011-May-12 12:19:42 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483222 2011-May-12 12:19:03 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft, aggregated (2)
2147483223 2011-May-12 12:18:02 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483224 2011-May-12 12:16:34 Informational %AAA-I-CONNECT: New http connection for user wayne, source 10.163.102.24 destination 10.167.152.131 ACCEPTED
2147483225 2011-May-12 12:02:38 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483226 2011-May-12 11:45:34 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483227 2011-May-12 11:39:50 Warning %SEC-W-SUPPLICANTUNAUTHORIZED: MAC 60:eb:69:a2:c3:7b was rejected on port e21
2147483228 2011-May-12 11:39:31 Informational %SEC-I-PORTAUTHORIZED: Port e30 is Authorized
2147483229 2011-May-12 11:39:31 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483230 2011-May-12 11:38:48 Informational %AAA-I-DISCONNECT: http connection for user wayne, source 10.163.102.24 destination 10.167.152.131 TERMINATED
2147483231 2011-May-12 11:30:57 Informational %AAA-I-CONNECT: New http connection for user wayne, source 10.163.102.24 destination 10.167.152.131 ACCEPTED
2147483232 2011-May-12 11:28:30 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483233 2011-May-12 11:21:24 Informational %AAA-I-DISCONNECT: http connection for user wayne, source 10.163.102.24 destination 10.167.152.131 TERMINATED
2147483234 2011-May-12 11:19:18 Informational %AAA-I-CONNECT: New http connection for user wayne, source 10.163.102.24 destination 10.167.152.131 ACCEPTED
2147483235 2011-May-12 11:19:03 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft, aggregated (2)
2147483236 2011-May-12 11:18:02 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483237 2011-May-12 11:11:26 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483238 2011-May-12 10:54:22 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483239 2011-May-12 10:37:18 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483240 2011-May-12 10:34:23 Informational %AAA-I-DISCONNECT: http connection for user wayne, source 10.163.102.24 destination 10.167.152.131 TERMINATED
2147483241 2011-May-12 10:21:25 Informational %AAA-I-CONNECT: New http connection for user wayne, source 10.163.102.24 destination 10.167.152.131 ACCEPTED
2147483242 2011-May-12 10:20:14 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483243 2011-May-12 10:19:03 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft, aggregated (2)
2147483244 2011-May-12 10:18:01 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483245 2011-May-12 10:03:10 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483246 2011-May-12 09:46:06 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483247 2011-May-12 09:29:02 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483248 2011-May-12 09:19:02 Informational %SEC-I-PORTAUTHORIZED: Port e26 is Authorized
2147483249 2011-May-12 09:19:02 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft, aggregated (1)
2147483250 2011-May-12 09:18:13 Informational %SEC-I-PORTAUTHORIZED: Port e27 is Authorized
2147483251 2011-May-12 09:18:13 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft, aggregated (1)
2147483252 2011-May-12 09:18:06 Note %COPY-N-TRAP: The copy operation was completed successfully
2147483253 2011-May-12 09:18:01 Informational %SEC-I-PORTAUTHORIZED: Port e48 is Authorized
2147483254 2011-May-12 09:18:01 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483255 2011-May-12 09:17:56 Informational %COPY-I-FILECPY: Files Copy - source URL flash://startup-config destination URL flash://mirror-config
2147483256 2011-May-12 09:17:14 Warning %SEC-W-SUPPLICANTUNAUTHORIZED: MAC 60:eb:69:a2:ba:fb was rejected on port e27
2147483257 2011-May-12 09:17:07 Warning %SEC-W-SUPPLICANTUNAUTHORIZED: MAC 60:eb:69:a2:bf:f4 was rejected on port e23
2147483258 2011-May-12 09:17:05 Warning %SEC-W-SUPPLICANTUNAUTHORIZED: MAC 60:eb:69:a2:bf:34 was rejected on port e25
2147483259 2011-May-12 09:16:56 Warning %STP-W-PORTSTATUS: e26 of instance 0: STP status Forwarding
2147483260 2011-May-12 09:16:53 Warning %STP-W-PORTSTATUS: e27 of instance 0: STP status Forwarding
2147483261 2011-May-12 09:16:52 Informational %LINK-I-Up: e26
2147483262 2011-May-12 09:16:50 Warning %LINK-W-Down: e26
2147483263 2011-May-12 09:16:48 Informational %LINK-I-Up: e27
2147483264 2011-May-12 09:16:46 Warning %LINK-W-Down: e27
2147483265 2011-May-12 09:16:46 Warning %STP-W-PORTSTATUS: e23 of instance 0: STP status Forwarding
2147483266 2011-May-12 09:16:46 Warning %STP-W-PORTSTATUS: e48 of instance 0: STP status Forwarding
2147483267 2011-May-12 09:16:43 Warning %STP-W-PORTSTATUS: e25 of instance 0: STP status Forwarding
2147483268 2011-May-12 09:16:42 Informational %LINK-I-Up: e23
2147483269 2011-May-12 09:16:42 Informational %LINK-I-Up: e48
2147483270 2011-May-12 09:16:40 Warning %LINK-W-Down: e48
2147483271 2011-May-12 09:16:40 Warning %LINK-W-Down: e23
2147483272 2011-May-12 09:16:39 Informational %LINK-I-Up: e25
2147483273 2011-May-12 09:16:38 Warning %STP-W-PORTSTATUS: e26 of instance 0: STP status Forwarding
2147483274 2011-May-12 09:16:37 Warning %LINK-W-Down: e25
2147483275 2011-May-12 09:16:36 Warning %STP-W-PORTSTATUS: e27 of instance 0: STP status Forwarding
2147483276 2011-May-12 09:16:34 Informational %LINK-I-Up: e26
2147483277 2011-May-12 09:16:32 Warning %LINK-W-Down: e26
2147483278 2011-May-12 09:16:32 Informational %LINK-I-Up: e27
2147483279 2011-May-12 09:16:30 Warning %LINK-W-Down: e27
2147483280 2011-May-12 09:16:29 Warning %STP-W-PORTSTATUS: e23 of instance 0: STP status Forwarding
2147483281 2011-May-12 09:16:27 Warning %STP-W-PORTSTATUS: e48 of instance 0: STP status Forwarding
2147483282 2011-May-12 09:16:26 Warning %STP-W-PORTSTATUS: e25 of instance 0: STP status Forwarding
2147483283 2011-May-12 09:16:24 Informational %LINK-I-Up: e23
2147483284 2011-May-12 09:16:23 Warning %LINK-W-Down: e23
2147483285 2011-May-12 09:16:22 Informational %LINK-I-Up: e48
2147483286 2011-May-12 09:16:22 Informational %LINK-I-Up: e25
2147483287 2011-May-12 09:16:20 Warning %LINK-W-Down: e48
2147483288 2011-May-12 09:16:20 Warning %LINK-W-Down: e25
2147483289 2011-May-12 09:11:58 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483290 2011-May-12 08:54:54 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483291 2011-May-12 08:37:50 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483292 2011-May-12 08:20:46 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483293 2011-May-12 08:20:25 Warning %SEC-W-SUPPLICANTUNAUTHORIZED: MAC 60:eb:69:a2:c3:94 was rejected on port e20 , aggregated (1)
2147483294 2011-May-12 08:20:07 Warning %SEC-W-SUPPLICANTUNAUTHORIZED: MAC 60:eb:69:a2:c3:94 was rejected on port e20
2147483295 2011-May-12 08:20:07 Warning %SEC-W-PORTUNAUTHORIZED: Port e20 is unAuthorized
2147483296 2011-May-12 08:16:58 Warning %SEC-W-SUPPLICANTUNAUTHORIZED: MAC 60:eb:69:a2:5c:b1 was rejected on port e2
2147483297 2011-May-12 08:16:58 Warning %SEC-W-PORTUNAUTHORIZED: Port e2 is unAuthorized
2147483298 2011-May-12 08:03:42 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483299 2011-May-12 08:00:04 Warning %SEC-W-SUPPLICANTUNAUTHORIZED: MAC 60:eb:69:a2:be:13 was rejected on port e19
2147483300 2011-May-12 08:00:04 Warning %SEC-W-PORTUNAUTHORIZED: Port e19 is unAuthorized
2147483301 2011-May-12 07:46:38 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483302 2011-May-12 07:40:23 Warning %SEC-W-PORTUNAUTHORIZED: Port e18 is unAuthorized
2147483303 2011-May-12 07:40:22 Warning %SEC-W-SUPPLICANTUNAUTHORIZED: MAC 60:eb:69:a2:c3:23 was rejected on port e5 , aggregated (1)
2147483304 2011-May-12 07:40:10 Warning %SEC-W-SUPPLICANTUNAUTHORIZED: MAC 60:eb:69:a2:b4:b9 was rejected on port e28
2147483305 2011-May-12 07:40:10 Warning %SEC-W-PORTUNAUTHORIZED: Port e28 is unAuthorized
2147483306 2011-May-12 07:40:04 Warning %SEC-W-SUPPLICANTUNAUTHORIZED: MAC 60:eb:69:a2:c3:23 was rejected on port e5
2147483307 2011-May-12 07:40:04 Warning %SEC-W-PORTUNAUTHORIZED: Port e5 is unAuthorized
2147483308 2011-May-12 07:29:34 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483309 2011-May-12 07:19:49 Informational %SEC-I-PORTAUTHORIZED: Port e20 is Authorized
2147483310 2011-May-12 07:19:49 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft, aggregated (1)
2147483311 2011-May-12 07:19:34 Warning %SEC-W-SUPPLICANTUNAUTHORIZED: MAC 60:eb:69:a2:c2:19 was rejected on port e43
2147483312 2011-May-12 07:19:34 Warning %SEC-W-PORTUNAUTHORIZED: Port e43 is unAuthorized
2147483313 2011-May-12 07:16:22 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483314 2011-May-12 07:12:30 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483315 2011-May-12 06:59:46 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483316 2011-May-12 06:55:26 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483317 2011-May-12 06:39:46 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483318 2011-May-12 06:38:22 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483319 2011-May-12 06:21:18 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483320 2011-May-12 06:19:16 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft, aggregated (1)
2147483321 2011-May-12 06:16:22 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483322 2011-May-12 06:04:14 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483323 2011-May-12 05:59:46 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483324 2011-May-12 05:47:10 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483325 2011-May-12 05:39:46 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483326 2011-May-12 05:30:06 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483327 2011-May-12 05:19:15 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft, aggregated (1)
2147483328 2011-May-12 05:16:22 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483329 2011-May-12 05:13:02 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483330 2011-May-12 04:59:45 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483331 2011-May-12 04:58:57 Warning %SEC-W-SUPPLICANTUNAUTHORIZED: MAC 60:eb:69:a2:c3:25 was rejected on port e47
2147483332 2011-May-12 04:58:57 Warning %SEC-W-PORTUNAUTHORIZED: Port e47 is unAuthorized
2147483333 2011-May-12 04:55:58 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483334 2011-May-12 04:39:46 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483335 2011-May-12 04:38:54 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483336 2011-May-12 04:21:50 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483337 2011-May-12 04:19:15 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft, aggregated (1)
2147483338 2011-May-12 04:16:22 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483339 2011-May-12 04:04:46 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483340 2011-May-12 03:59:45 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft, aggregated (1)
2147483341 2011-May-12 03:58:39 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483342 2011-May-12 03:47:42 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483343 2011-May-12 03:39:46 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483344 2011-May-12 03:30:38 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483345 2011-May-12 03:19:15 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft, aggregated (1)
2147483346 2011-May-12 03:16:22 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483347 2011-May-12 03:13:34 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483348 2011-May-12 02:59:45 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft, aggregated (1)
2147483349 2011-May-12 02:58:39 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483350 2011-May-12 02:56:30 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483351 2011-May-12 02:41:10 Warning %STP-W-PORTSTATUS: e48 of instance 0: STP status Forwarding
2147483352 2011-May-12 02:41:06 Informational %LINK-I-Up: e48
2147483353 2011-May-12 02:41:04 Warning %LINK-W-Down: e48
2147483354 2011-May-12 02:39:46 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483355 2011-May-12 02:39:26 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483356 2011-May-12 02:34:30 Warning %STP-W-PORTSTATUS: e45 of instance 0: STP status Forwarding
2147483357 2011-May-12 02:34:25 Informational %LINK-I-Up: e45
2147483358 2011-May-12 02:34:23 Warning %LINK-W-Down: e45
2147483359 2011-May-12 02:22:22 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483360 2011-May-12 02:19:15 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft, aggregated (1)
2147483361 2011-May-12 02:16:21 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483362 2011-May-12 02:15:55 Warning %STP-W-PORTSTATUS: e2 of instance 0: STP status Forwarding
2147483363 2011-May-12 02:15:51 Informational %LINK-I-Up: e2
2147483364 2011-May-12 02:15:49 Warning %LINK-W-Down: e2
2147483365 2011-May-12 02:05:18 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483366 2011-May-12 01:59:45 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft, aggregated (1)
2147483367 2011-May-12 01:58:39 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483368 2011-May-12 01:48:14 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483369 2011-May-12 01:39:45 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483370 2011-May-12 01:31:10 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483371 2011-May-12 01:19:15 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483372 2011-May-12 01:14:06 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483373 2011-May-12 00:59:45 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft, aggregated (1)
2147483374 2011-May-12 00:58:38 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483375 2011-May-12 00:57:02 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483376 2011-May-12 00:39:58 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483377 2011-May-12 00:39:45 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483378 2011-May-12 00:39:16 Warning %SEC-W-SUPPLICANTUNAUTHORIZED: MAC 60:eb:69:a2:b7:9a was rejected on port e24
2147483379 2011-May-12 00:39:16 Warning %SEC-W-PORTUNAUTHORIZED: Port e24 is unAuthorized
2147483380 2011-May-12 00:22:54 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483381 2011-May-12 00:19:14 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483382 2011-May-12 00:05:50 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483383 2011-May-11 23:59:45 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft, aggregated (1)
2147483384 2011-May-11 23:58:38 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483385 2011-May-11 23:48:46 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483386 2011-May-11 23:39:46 Informational %SEC-I-PORTAUTHORIZED: Port e18 is Authorized
2147483387 2011-May-11 23:39:45 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft, aggregated (1)
2147483388 2011-May-11 23:38:50 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483389 2011-May-11 23:31:42 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483390 2011-May-11 23:19:14 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483391 2011-May-11 23:14:38 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483392 2011-May-11 22:59:45 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft, aggregated (1)
2147483393 2011-May-11 22:58:38 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483394 2011-May-11 22:57:34 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483395 2011-May-11 22:40:30 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483396 2011-May-11 22:39:45 Informational %SEC-I-PORTAUTHORIZED: Port e5 is Authorized
2147483397 2011-May-11 22:39:45 Informational %SEC-I-PORTAUTHORIZED: Port e28 is Authorized
2147483398 2011-May-11 22:39:44 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft, aggregated (1)
2147483399 2011-May-11 22:38:49 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483400 2011-May-11 22:23:26 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483401 2011-May-11 22:19:14 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483402 2011-May-11 22:06:22 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483403 2011-May-11 21:59:45 Informational %SEC-I-PORTAUTHORIZED: Port e19 is Authorized
2147483404 2011-May-11 21:59:45 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft, aggregated (1)
2147483405 2011-May-11 21:58:38 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483406 2011-May-11 21:49:18 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483407 2011-May-11 21:39:44 Informational %SEC-I-PORTAUTHORIZED: Port e2 is Authorized
2147483408 2011-May-11 21:39:44 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft, aggregated (1)
2147483409 2011-May-11 21:38:49 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483410 2011-May-11 21:32:14 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483411 2011-May-11 21:20:02 Warning %SEC-W-SUPPLICANTUNAUTHORIZED: MAC 60:eb:69:a1:93:3f was rejected on port e7
2147483412 2011-May-11 21:19:14 Informational %SEC-I-PORTAUTHORIZED: Port e43 is Authorized
2147483413 2011-May-11 21:19:14 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483414 2011-May-11 21:15:10 Debug %SNTP-D-NTPBADVER: NTP server version not compatible
2147483415 2011-May-11 20:58:38 Warning %AAAEAP-W-RADIUSREPLY: Invalid attribute 26 ignored - vendor id is not Microsoft
2147483416 2011-May-11 20:58:06 Debug %SNTP-D-NTPBADVER: NTP server version not compatible -
SCUP/SCCM install of 11.3.300.257 fails
Hi,
I'm having trouble deploying the new combined 32/64bit version of Flash published through the SCUP cab catalog and SCCM Software Updates deployment. On every one of my machines the update fails with the same error. I have a mixed environment of Win XP 32bit and Win 7 64 bit machines.
I've previously had no trouble at all deploing Flash (and other Adobe updates) updates using the SCUP catalog and SCCM. It is first with 11.3.300.257, where the msi contains binaries for both 32 and 64 bit, that i experiece issues.
The error i get in the WindowsUpdate.log is:
WUAHandler.log (SCCM related log) gives the error:
Installation job encountered some failures: Error = 0x80240022.
UpdatesHandler.log (SCCM related log) gives the error:
Update execution failed.
The Windows Application Event Log displays nothing in relation to the msi, so no usefull info there.
Anyone else out there with the same issues, or with some guidance?
Br,
DavidHave, I am having the exact same problem. But 90% of my machines are fine. It is the about 30 machines, about 10% of the total, which fail with this error message. I cant see anything wrong with these machines, or anything in common thats different from the machines that patch ok.
This has occurred with all Flash ActiveX updates for Internet Explorer since I began using SCUP with SCCM.
any other advice that could be of use? Thanks! -
2911 ISM and CUE: Do I need to (re-)install CUE for GUI access?
To all the experts out there, I am volunteering with a IPT (Voice) install for my Church. They have a 2911ISR router, which I am trying to setup / configure for a small office configuration.
The question is as stated: Do I need to (re-)install CUE to get the GUI (web UI) to work? It shipped with CUE 8.6.6 on the ISM-SRE-300-K9 module. But I'm not sure if it is because the GUI isn't there or if I have configured the interfaces and route incorrectly.
Here is the software list on the ISM:
MACC-2911-CUE# sh soft inst his
Software Installation History:
Refer to install.log for more details
2014-03-19 12:48:39 ***Install Command Issued*** Cmd:1 Opt:0, Pkg:cue-allapps.sme.8.6.6.pkg Url:ftp://10.1.1.1// Mode:1 Proto:1 Host:10.1.1.1
2014-03-19 12:56:41 ***SOFTWARE CLEANED***
Timestamp Subsystem Version Description UID
2014-03-19 12:56:42 Thirdparty 8.6.6 Service Engine Thirdparty Code a3442277-7890-4782-9e6b-9d19efc1e0d8
2014-03-19 12:56:42 Plug-in Enablement 8.6.6 Plug-in enablement pack 26bd663c-3e5a-43d9-a6c3-5441ce44941b
2014-03-19 12:56:42 CUE Voicemail Language Support 8.6.6 Languages global pack e2e81cc6-39b5-47e1-9f83-b83c897fc50c
2014-03-19 12:56:42 Global 8.6.6 Global manifest edceaf0b-a890-4045-9086-5452fac85eba
2014-03-19 12:56:42 Infrastructure 8.6.6 Service Engine Infrastructure a36e1be1-ce8a-4f53-ace7-1844262aa0b9
2014-03-19 12:56:42 GPL Infrastructure 8.6.6 Service Engine GPL Infrastructure 9f112eb1-6f58-4dd4-8faa-8530467af3b9
2014-03-19 12:56:42 Voice Mail 8.6.6 Voicemail application 8e7823e2-0e92-4470-8860-653246345f9d
2014-03-19 12:56:42 CUE Voicemail UK English 8.6.6 British English language pack fa803d25-9c89-4171-a14c-ec12d6ed6b8c
2014-03-19 12:56:42 Bootloader (Secondary) 2.1.36 Service Engine Bootloader 9d7b26fb-21b2-416e-8b65-425c2f8da5d8
2014-03-19 12:56:42 Installer 8.6.6 Installer a0fb9f0a-fa5c-4b21-a64c-0cb9d6379573
2014-03-19 12:56:42 Core 8.6.6 Service Engine OS Core 430f25f9-0fed-48a4-b362-823937138501
2014-03-19 12:56:42 Auto Attendant 8.6.6 Service Engine Telephony Infrastructure e3db91b0-f47d-460c-ad22-65001a5d45a9
2014-03-19 13:01:48 ***SOFTWARE CLEANED***
Timestamp Subsystem Version Description UID
2014-03-19 13:06:40 ***SOFTWARE CLEANED***
Timestamp Subsystem Version Description UID
2014-03-19 23:17:44 ***SOFTWARE CLEANED***
Timestamp Subsystem Version Description UID
2014-03-19 23:41:53 ***SOFTWARE CLEANED***
Timestamp Subsystem Version Description UID
2014-04-20 17:47:59 ***SOFTWARE CLEANED***
Timestamp Subsystem Version Description UID
Refer to install.log for more details
Can you confirm the GUI files are there, or are they missing; in which case I need to (re-)install CUE?
Thanks in advance for any assistance you can provide. It is greatly appreciated.Hi Kevin. I do have that in place.
maccrouter1#sh ip route
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP
+ - replicated route, % - next hop override
Gateway of last resort is 192.168.1.1 to network 0.0.0.0
S* 0.0.0.0/0 [1/0] via 192.168.1.1, GigabitEthernet0/0
10.0.0.0/8 is variably subnetted, 11 subnets, 3 masks
C 10.0.4.0/24 is directly connected, GigabitEthernet0/1.4
L 10.0.4.1/32 is directly connected, GigabitEthernet0/1.4
C 10.0.100.0/23 is directly connected, GigabitEthernet0/1.100
L 10.0.100.1/32 is directly connected, GigabitEthernet0/1.100
C 10.0.150.0/24 is directly connected, GigabitEthernet0/1.150
L 10.0.150.1/32 is directly connected, GigabitEthernet0/1.150
S 10.0.150.2/32 is directly connected, ISM0/0
C 10.0.200.0/24 is directly connected, GigabitEthernet0/1.200
L 10.0.200.1/32 is directly connected, GigabitEthernet0/1.200
C 10.1.1.0/24 is directly connected, Loopback0
L 10.1.1.1/32 is directly connected, Loopback0
171.16.0.0/16 is variably subnetted, 2 subnets, 2 masks
C 171.16.0.0/23 is directly connected, GigabitEthernet0/1.16
L 171.16.0.1/32 is directly connected, GigabitEthernet0/1.16
192.168.1.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.1.0/24 is directly connected, GigabitEthernet0/0
L 192.168.1.9/32 is directly connected, GigabitEthernet0/0
Could the router side interface be the problem? Here is how it is configured:
interface GigabitEthernet0/1.150
description $FW_INSIDE$
encapsulation dot1Q 150
ip address 10.0.150.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
zone-member security in-zone
shutdown
I should be working on the router in the morning, so unless something obvious is indicated in the above config listing, I'll post a new 'show run' as soon as I can.
Thanks, Jim.
Maybe you are looking for
-
Please help I keep getting this error message trying to save a photo in photoshop to return to lightroom
-
RAM on 8 core. is 4x4gb or 8x2gb faster?
I'm adding 16 GB of ram to my new 8 core mac pro. if I add 4 4gb chips, I can later easily expand to 32GB, however, I have a vague memory of someone saying that it will be faster to add eight 2gb chips. Is that true?
-
AQ: Best practice for dequeuing a queue
Is it a good way to create a job that uses dequeue on the queue-table (each 30 second). But the procedure called in the job has an endless-Loop which runs as long as the database runs. So the job didn't restart all 30 seconds... This is the technique
-
Can't delete or set delete flag on PP order
I want to delete a PP order and it tells me that I cannot select selected assembly order xxxxxx for deletion. The status of the order is REL MSPT PRT PRC RESA SETC. The production order has no goods movements associated with it , yet I can not d
-
Hopefully someone out there can help solve this one. How do you get a child window to automatically resize within a parent window? On their own both the child window and the parent window behave as expected but once we attempt to load the child windo