ISR 2811 with VIC2-2FXS

hi,
We have deployed cisco 2811 router in our network and had installed vic2-2fxs card in one of the HWIC slot.We need to configure fxs card for voip to make a call to branch office and have the following ios c2800nm-ipvoicek9-mz.124-17.bin .The problem we are facing is the router detect vic card under show version command but when show running-config command been given it doesn't display voice-port information to configure the same.We have attached the show tech-support o/p.any suggestion welcomed.

Hi Bhavesh,
It Looks like you do not have any DSP resources.You will need something like a PVDM2-8 card on the motherboard to provide DSP resources to the FXS card. Without DSP resources you cannot configure the FXS :)
Hope this helps!
Rob

Similar Messages

VIC2-2FXS at Cisco 2811 ISR, is NM-HDV2 needed?

Hello,
I have a Cisco 2811 router that is configured as CUCME and working OK. So I need to connect a fax machine so I decided to take FXS card, but I don't know if I need to find NM-HDV2 to get VIC2-2FXS working on 2811, or it works at any of HWIC slots... I have FXO (VIC2-4FXO) working w/o any network module (installed at HWIC slot), so do I need such for FXS?
P.S.: I have PVDM2-8 installed in the router, will it be enough?
Thank you.

The NM is not needed.
The PVDM that you have is enough.

VIC2-2FXS problems

Hi,
we have ISR 2801 router with 2xVIC2-2BRI-NT/TE, 1xVIC2-2FXS and PVDM2-8, IOS ver.c2801-spservicesk9-mz.124-9.T7.bin. We can see ISDN BRI ports but cannot see FXS ports.
Any help?
here some outputs from router:
sh ver.
Cisco 2801 (revision 7.0) with 235520K/26624K bytes of memory.
Processor board ID FCZ121412Q8
2 FastEthernet interfaces
4 ISDN Basic Rate interfaces
2 Voice FXS interfaces
1 DSP, 4 Voice resources
DRAM configuration is 64 bits wide with parity disabled.
191K bytes of NVRAM.
126976K bytes of ATA CompactFlash (Read/Write)
sh invent
NAME: "chassis", DESCR: "2801 chassis"
PID: CISCO2801 , VID: V04 , SN: FCZ121412Q8
NAME: "VIC 0", DESCR: "2nd generation two port BRI voice interface daughtercard"
PID: VIC2-2BRI-NT/TE , VID: V02 , SN: FOC12093QZW
NAME: "WIC/VIC/HWIC 1", DESCR: "2nd generation two port BRI voice interface daughtercard"
PID: VIC2-2BRI-NT/TE , VID: V02 , SN: FOC12093QL0
NAME: "WIC/VIC 2", DESCR: "2nd generation two port FXS voice interface daughtercard"
PID: VIC2-2FXS , VID: V01 , SN: FOC12121ZWM
NAME: "PVDM 0", DESCR: "PVDMII DSP SIMM with one DSP with half channel capcity"
PID: PVDM2-8 , VID: V01 , SN: FOC12085ZJS
sh voice port summ
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
============== == ============ ===== ==== ======== ======== ==
0/0/0 1 bri-voice up dorm none none y
0/0/0 2 bri-voice up dorm none none y
0/0/1 1 bri-voice up dorm none none y
0/0/1 2 bri-voice up dorm none none y
0/1/0 1 bri-voice up dorm none none y
0/1/0 2 bri-voice up dorm none none y
0/1/1 1 bri-voice up dorm none none y
0/1/1 2 bri-voice up dorm none none y

I found out a solution. The problem is generated by insufficient DSP resources (PVDM2-8, I need more...).I had rearranged the position of the card and of course I've lost one ISDN BRI port. The result is as follow:
sh voice port summ
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
============== == ============ ===== ==== ======== ======== ==
0/0/0 1 bri-voice up dorm none none y
0/0/0 2 bri-voice up dorm none none y
0/0/1 1 bri-voice up dorm none none y
0/0/1 2 bri-voice up dorm none none y
0/1/0 -- fxs-ls up dorm on-hook idle y
0/1/1 -- fxs-ls up dorm on-hook idle y
0/2/0 1 bri-voice up dorm none none y
0/2/0 2 bri-voice up dorm none none y
voice-port 0/0/0
voice-port 0/0/1
voice-port 0/1/0
voice-port 0/1/1
voice-port 0/2/0
I hope that this will help anyone with this situation.

Testing VIC2-2FX S and VIC2-2FXO cards

I want to setup two 2611XM routers with a
NM-HD-2VE ( 3 DSP), VIC2-2FXS, VIC2-2FXO cards.
Can I connect the FXS to the FXO ?
Do I need to have telephones with RJ11 Straight through cables connected to the ports of the VIC's.
Could you point me to somewhere where this scenario is addressed. ( Voice certification test lab diagrams...)
Thank you,
Tom

Dear Experts
This is going to be my first implimentation of the Voice network and is turning out to be a nightmare.i have reffered all the configuration mannuals , books and videos but still not able to make calls across the MPLS network.Need help urgently to solve the issue.
Here is the senario
PSTN>>>FXO(Cisco2905)>>>>>MPLS Cloud<<<<<<<(Cisco2905)FXS>>>>>>>>Phone
here is the configuration i have done
<<<<<<<<<>>>>>>>>
voice-port 0/1/0
voice-port 0/1/1
connection plar 2201
voice-port 0/1/2
voice-port 0/1/3
mgcp profile default
dial-peer voice 998 voip
destination-pattern 22..
session target ipv4:192.168.220.1
dtmf-relay cisco-rtp
dial-peer voice 100 pots
destination-pattern 9............
port 0/1/1
on
<<<<<<<<>>>>>>.
voice-port 0/0/0
cptone ID
voice-port 0/0/1
cptone ID
mgcp profile default
dial-peer voice 220 pots
destination-pattern 2201
port 0/0/0
forward-digits all
dial-peer voice 221 pots
destination-pattern 2202
port 0/0/1
forward-digits all
dial-peer voice 110 voip
destination-pattern 9T
session target ipv4:192.168.0.1
dtmf-relay cisco-rtp
=====================================
Early response is much appriciated
REGARDS
SANDEEP

Vic2 - 2FXS Card in 2801 and modem / fax usage

Hi,
I have a Cisco 2801 running c2801-advipservicesk9-mz.124-9.T.bin
It has 2 VIC2-2BRI-NT/TE cards, 1 VIC2-2FXS. And a PVDM2-8 and a PVDM2-16 as DSP's.
I am trying to get a modem working on a FXS port, but one way or the other it's just not comming together.
I do have a propper PSTN line when I use an analogue phone, but when I try to hook up a modem nothing or sometimes a crappy 2k4 connection.
What am I missing here, I thought by putting in enough DSP's in the router and a FXS card and BRI cards this should work.
Nothing fancy configured on the voice ports (first 4 are BRI last 2 FXS)
voice-port 0/0/0
compand-type a-law
cptone CH
voice-port 0/0/1
compand-type a-law
cptone CH
voice-port 0/1/0
compand-type a-law
cptone CH
voice-port 0/1/1
compand-type a-law
cptone CH
voice-port 0/2/0
cptone CH
voice-port 0/2/1
cptone CH
Can anyone tell me what to do to get a modem working propperly on this FXS ports ?

You may want to try adding this command:
voice service voip
modem passthrough nse codec g711alaw

Cisco ISR-2801 With ADVIPSVC-K9-MZ and no IDS

Can someone tell me why I have some older routers with the advanced ip services images and ip audit (IDS) services work and the new ISR router with the
Advanced ip services k9 image doesnt. I went throught the software advisor and it looks like it should support audit rules and signatures with defined actions etc. I dont have any of these options. on this 12.4-12-mz image its running on. Can someone clarify why?
Thanks,

Secure Sockets Layer provides security for web transactions by handling authentication, data enryption and digital signatures. The 2800 Series supports SSL VPNs and SSL acceleration via the AIM-VPN/SSL-3.

Config 2811 with NM-HDV-2E1-60 module for Voice over IP

Hi,
How should I config 2811 with NM-HDV-2E1-60 for voice over IP?
Which IOS I should use?
I can't define "Controller e1".
Can any one send me a configuration example file?
Tanx

Can you provide more info?
How are you trying to use this? Are you going to use this router as a CallManager express or in conjunction with CallManager server?
Can you provide a sh ver and sh run and a sh diag from your router? Do you have a design document of the set up that you have in mind?
Also please note that if you want to change the feature set of IOS that comes with the router, you need to purchase the software from Cisco, as you need to be able to upgrade to another IOS. This upgrade is not free.
Looking forward to hear more about your set up to be able to help you.
Regards,
Farbod

Etherchannel 2811 with 4501 Catalyst switch

I am trying to set up an Etherchannel between two FastEthernet on 2811 with a Catalyst 4501 switch. The channel is established fine except that I can't get any traffic to go across the etherchannel. Any ideas?
Thanks in advance

Only ports on etherswitch module support channeling in a 2811(built in FE interfaces do not)

1760 and VIC2 2FXS

What IOS will I need to configure analogue voice ports on a 1760 router? I've tried following the IOS selector but most of the releases it suggests are deferred.

According to the following link, the VIC-2FXS card is supported in all versions of IOS for the 1760 with a voice feature set.
http://www.cisco.com/en/US/tech/tk652/tk653/technologies_tech_note09186a0080094fac.shtml
Hope this helps. If so, please rate the post.
Brandon

Cisco 2811 with NM-16A as Terminal server.

Hello,
I am currently looking for a Cisco terminal server solution to remotely access through console my private Cisco home lab. I am thinking of buying Cisco 2811 but I struggle to figure out the difference which ASYNC/SYNC MODULE to use. So, my question, is it possible to use NM-16A module with Cisco 2811 or HWIC-16A module must be used? And what is the difference between them?
I found on Cisco website that NM-16A is not supported on Cisco 2811, however some forums stated that it is possible.
http://www.cisco.com/en/US/docs/ios/interface/configuration/guide/ir_nm16as.html#wp1027188
Your help is deeply appreciated.
Thank you,
Arik

Async is what you need.
I run this senario several places;
NAME: "chassis", DESCR: "2801 chassis"
PID: CISCO2801 ,
NAME: "WIC/VIC/HWIC 1", DESCR: "High Speed Wan Interface card with 16 RS232 async ports(HWIC-16A)"
PID: ,
NAME: "WIC/VIC/HWIC 3", DESCR: "9 Port FE Switch"
The HWIC is called HWIC-16A, but there is also a HWIC-8A
plus one or two CAB-HD8-ASYNC combo-squid-cables (green 1-to-8 with RJ45 plugs)
http://www.cisco.com/en/US/prod/collateral/modules/ps5949/ps6182/product_data_sheet0900aecd80274416.html
then you run rotary groups on the async SLIP's, via the cfg.
HTH
Martin

2811 and VIC2-2BRI-NT/TE. CCM 4.1.3

Hi,
I've an H323 gateway with a VIC2-2BRI-NT/TE to connect directly an ISDN Phone. I'm searching to display a name for this phone when it call an IP Phone. Anyone an idea ? The station-name voice-port command doesn't work with BRI interface. Thanks

Here it is :
boot system flash:c2800nm-spservicesk9-mz.124-4.XC1.bin
isdn switch-type basic-net3
voice-card 0
no dspfarm
voice class h323 1
h225 timeout tcp establish 3
call preserve
interface BRI0/0/0
no ip address
isdn switch-type basic-net3
isdn overlap-receiving
isdn protocol-emulate network
isdn layer1-emulate network
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn outgoing display-ie
isdn skipsend-idverify
line-power
interface BRI0/0/1
no ip address
isdn switch-type basic-net3
isdn overlap-receiving
isdn protocol-emulate network
isdn layer1-emulate network
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn outgoing display-ie
isdn skipsend-idverify
line-power
ip route 0.0.0.0 0.0.0.0 X.Y.Z.W
voice-port 0/0/0
compand-type a-law
cptone CH
dial-peer voice 10 pots
tone ringback alert-no-PI
preference 1
destination-pattern 4976
direct-inward-dial
port 0/0/1
forward-digits all
dial-peer voice 20 voip
preference 1
destination-pattern 6671
progress_ind setup enable 3
voice-class h323 1
session target ipv4:10.16.246.41
codec g711ulaw
ip qos dscp cs5 media
no vad
dial-peer voice 21 voip
preference 2
destination-pattern 6671
progress_ind setup enable 3
session target ipv4:10.19.133.41
codec g711ulaw
ip qos dscp cs5 media
no vad

Error registering a Cisco 2811 with a clustered CallManager 4.3

Hello, i'm having problems registering a Cisco 2811 Gateway with a VWIC2-1MFT-E1 interface card with Cisco CallManager 4.3.
The error displayed when debugging mgcp is the following:
//-1/xxxxxxxxxxxx/MGCP/mgcp_mp_get_not_entity(828):[lvl=2]
Invalid parameter (pkt 0x4708C5E8 pkt->mgcp_parm_lines 0x00000000)
I configured mgcp by the following:
mgcp
mgcp call-agent VOIPSVR1 2427 service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode out-of-band
mgcp rtp unreachable timeout 1000 action notify
mgcp restart-delay 300
mgcp package-capability rtp-package
no mgcp package-capability res-package
mgcp package-capability sst-package
no mgcp package-capability fxr-package
mgcp package-capability pre-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp validate call-agent source-ipaddr
mgcp rtp payload-type g726r16 static
mgcp profile default
dial-peer voice 100 pots
service mgcpapp
direct-inward-dial
port 0/0/0:15
Previously, the gateway downloaded xml config files from the Cisco CallManager without problems and, in addition, when trying to add a Route Group (in the CallManager) this Gateway does not appear
in the list of Available Devices although
I have added it through the Device->Gateway Menu.
Need some advice and help. Thank you in advance.

Hi Jose,
The Domain name issue is outlined nicely in this doc;
MGCP Gateway Registration Failure with Cisco CallManager
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a00805a316c.shtml#prob
If the IP domain name is configured in Cisco IOS on the MGCP gateway, enter the Fully Qualified Domain Name (FQDN) in the Domain Name field.
In the example: test and cisco.com represent the hostname and domain name respectively. If the IP domain name is not configured in Cisco IOS on the MGCP gateway, enter only the hostname of the MGCP gateway in the Domain Name field.
You would enter test.cisco.com (in CCM)
Hope this helps!
Rob

CME 3.3 on 2811 with Polycom VSX 7000

All -
I have a polycom VSX7000 without the integrated MCU.
I also have a 2811 running CME 3.3 with about 20 IP phones attached.
I'd like to come up with a solution so that my IP phone users could participate in a video conference as audio-only users.
Is there any chance that transcoding on the 2811 using spare PVDM2 resources could do this?
I've already gotten an IP phone to call the VSX7K using an H.323 dialpeer, but as soon as the call is answered - it disconnects - presumably due to a codec mis-match.
The IPVC products seem to be overkill for my needs (and budget).
Suggestions?

I do not have an MCU or bridge in the network. The other video endpoints that may be involved are IP devices external to the network.
Our original design intent is that we are a single endpoint and would not have bandwidth available to support multiple external connections. The places to where we would connect on a video conference are larger, fixed sites more able to provide bridging services.
Then came the idea of supporting audio-only access of our local IP phones to the conference.
I'll definitely try the codec command on the H.323 dial peer.
I think I mentioned that the call would signal each end, but would fail to connect once the user tried to answer.

HWIC-3G-GSM on ISR 2811 Troubleshooting

Hi,
Documentation says this 3G card is working in 2800 routers. Why cannot my 2811 not recognize the card?
------------show diag
WIC Slot 0:
        Unknown WAN daughter card
        WIC module not supported/disabled in this slot
        Hardware Revision        : 1.0
        Top Assy. Part Number    : 800-28846-01
        Board Revision           : J0
        Deviation Number         : 0
        Fab Version              : 03
        PCB Serial Number        : FOC134119FD
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        Fab Part Number          : 28-7666-03
        Manufacturing Test Data : 00 00 00 00 00 00 00 00
        Field Diagnostics Data   : 00 00 00 00 00 00 00 00
        Product (FRU) Number     : HWIC-3G-GSM
        Version Identifier       : V01
        CLEI Code                : COUIAKTCAA
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF 40 05 1E 41 01 00 C0 46 03 20 00 70 AE 01
          0x10: 42 4A 30 88 00 00 00 00 02 03 C1 8B 46 4F 43 31
          0x20: 33 34 31 31 39 46 44 03 00 81 00 00 00 00 04 00
          0x30: 85 1C 1D F2 03 C4 08 00 00 00 00 00 00 00 00 C5
          0x40: 08 00 00 00 00 00 00 00 00 CB 8B 48 57 49 43 2D
          0x50: 33 47 2D 47 53 4D 89 56 30 31 20 D9 02 40 C1 C6
          0x60: 8A 43 4F 55 49 41 4B 54 43 41 41 FF FF FF FF FF
          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
The IOS is c2800nm-advipservicesk9-mz.124-9.T6.bin.
Any ideas are appreciated.
Thanks.
Larry

Larry,
     According to the below link, you need to be runing 12.4(15)T or later for the router to recognize the HWIC. So upgrade to at least 12.4(15)T and see if it gets recognized.
http://www.cisco.com/en/US/prod/collateral/modules/ps5949/prod_qas0900aecd806e0563.pdf
Steve

2811 with NM-2CE1T1-PRI module

I have installed an NM-2CE1T1-PRI module in a Cisco 2811 router and issued the "card type T1 1" command as well as the "controller t1 1/0" and "controller t1 1/1" commands and sub-commands as required, however, the associated serial interfaces never get defined in the router. I am using IOS version:
c2800nm-advsecurityk9-mz.124-17a.bin
Any ideas?

problem resolved .... channel-group command never dropped in from script .....

ISR 2811 with VIC2-2FXS

Similar Messages

Maybe you are looking for