Issue Apply Dynamic Interface from Prime

Hi all,
I have some problems applying a Dynamic Interface Template from prime to my WLC:
Prime: 1.3.0.20 Update 4
WLC 5508 / 7.4.110.0
I can Apply this template to older WLC versions.
The LAG mode is enabled on my WLC.
Any Idea?
Willem

If I click on "apply to controllers..." there is a list of controllers but the controller I want to apply the template to is not in this list (new controller, the first 7.4 connected to this prime, the other controllers are 4402 or 5508 all with 7.0.235.0) .
If I clear the LAG flag, there is one controller in the list but also not the one I want to apply the template to.
The controller will show up in other lists like "NTP".
I can also apply NTP Servers to this controller, what means that in general the communication is possible.

Similar Messages

  • Prime Infrastructure 2.1.1 cannot add more than two interfaces in Dynamic Interface Controller Templates

    Cisco Prime Infrastructure is a damned nightmare of browser bugs (some features work in IE8, some in IE9, and some only in Firefox).  And I am not sure if what I am experiencing is a browser bug - or a real bug - or something that I was able to do before and can't any more?  I would love for someone to either explain why this is happening to me, or reproduce the bug!
    I'm running Prime 2.1.1.  I am doing this ...
    Configure > Controller Template Launchpad
    System > Dynamic Interface
    Select a command > Add interface (GO)
    Enter all the properties - roll to the bottom of the page, and click Apply to Controllers
    I have four controllers.  And normally I would add an interface for each controller.  But I can only create two out of the four.  It doesn't matter which two I choose.  When I click Add under Manage Interfaces for the third controller, I cannot click the Done button to apply it (see screenshot, attached).  I have found that if I change the VLAN to something else, it will let me save it.  But ... why?  I went back and reviewed all of my existing interface templates and I am not doing anything different.  Although, they were all created a long while ago using WCS 7.x.
    Any help, guidance, or confirmation of insanity would be appreciated.
    -Steve Ballantyne

    I doubt I will get any hits on this here but I always try.  I opened a TAC case.  I will come back and comment on whatever they find.

  • Prime\SNMP Monitoring of dynamic interfaces

    Hi - Is anyone aware of a method of monitoring the bandwidth utilisation on a dynamic interface on a WLC?
    I'd like to monitor the traffic on each dynamic interface to generate usage stats on centrally switched guest and employee SSID's.
    Thanks

    You have to get that stats from switch where you defined those SVI. WLC dynamic interface not terminate any L3 traffic  & switch SVI is the place to go.
    If you have netflow monitoring or simple snmp monitoring tool, you can get that stats from the switch.
    HTH
    Rasika
    **** Pls rate all useful responses ****

  • Cisco Prime 2.0 Infrastructure-how to remove unneccessary interfaces from monitoring

    Hello all,
    We have Cisco Prime 2.0 Infrastructure and I would like to know how to remove certain interfaces from monitoring?  For example, I do not need monitoring on some ISDN and FXS/FXO ports.  I am receiving email alerts for ISDN channels going up/down for example.   Thanks.

    take a look at:::
    http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/2.0/user/guide/setup_groups.html

  • Encore CS6 Dynamic Link from Pr CS6 Problem/Issue

    I switched from Production Premium CS5 to CS6.  I first deactivated and uninstalled my CS5 then installed CS6 on my Windows 7 machine.
    The problem:
    When I edit together a video in Premiere CS6 and have finished, I use Dynamic Link from within Encore CS6 to bring in that timeline.  After that, I use AME to transcode that Dynamic Link asset to the DVD MPEG standard, Encore CS6 keeps poping up a  notification window that says:  "The transcoded DynamicLink asset _______ has changed on the server.  Would you like to reimport it?  Yes/No" It prompts me each time I enter Encore and any time I move from another open program back to Encore.
    And I have to click No for each timeline that I have used Dynamic Link for (which is usually 5 or so).
    Any ideas or help?  This is incredibly annoying.
    Thank you.
    Jared

    As an update.  I am using the newest version of PluralEyes (v 2.0.5  7358) to sync the audio of the multiple camera event films I have shot.  I have since created a new project in Premiere and only manually lined up clips and then Dynamically Linked that to a new Encore project and so far Encore has not promtpted me with the error/message:  "The transcoded DynamicLink asset _______ has changed on the server.  Would you like to reimport it?  Yes/No"
    Any ideas?  This is very frustrating.  Thank you!

  • Mgmt Via Dynamic Interface not working on 5505 version 7.2.111.3

    Folks,
             I have posted this question a couple of times on the forum but did not get a solution. I am trying to manage my 5508 controller from a dynamic interface which is assigned to port 7 of the controller. I have a switch connected to that port which has a PC on the same subnet as the dynamic interface. From the PC, I can ping the dynamic interface IP Address, but can not telnet,SSH,http or https to it. There is no clear doc that specifics how to effectly use the command "config network mgmt-via-dynamic-interface" command.
    Mgmt Via Wireless Interface................. Enable
    Mgmt Via Dynamic Interface.................. Enable
    Interface Name                   Port Vlan Id  IP Address      Type    Ap Mgr Guest
    173                                      7    173      172.16.101.100  Dynamic Yes    No
    management                         1    172      172.16.100.100  Static  Yes    No
    service-port                           N/A  N/A      0.0.0.0         DHCP    No     No
    virtual                                    N/A  N/A      1.1.1.1         Static  No     No
    7  Normal  Forw Enable  Auto       1000 Full  Up     Enable  N/A     1000BaseTX
    Any guidence would be highly appreciated.

    Im having a similar issue and have 2 TAC cases open.
    TAC CASE#1:  issue is that even when disbaled I can still access the dynmic interface via HTTPS/HTTPS/TELNET/SSH. But this is on a WISM1.
    Thanks a lot for your quick and prompt response, I see that there is an internal Bug with an ID CSCty32586.
    I see that the bug is fixed told be fixed in 7.0.230.0, but it’s not fixed. The bug is fixed in 7.2.x version.
    I understand that you are using Wism on which 7.1.x version and above is not supported.
    As 7.0.235.3 is released recently to overcome some of the changes and to fix some of the Bugs with older version on these devices.
    Kindly try to upgrade the software version of the WLC to 7.0.235.3 and check the compatibility.
    Please do let me know in case of any concerns and I will be glad to assist you.
    TAC CASE#2: Just like you I can not access the dynamic interface. Still working that one .. The holiday dropped when I just opened that case.
    "Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
    ‎"I'm in a serious relationship with my Wi-Fi. You could say we have a connection."

  • Cannot contact Non-native dynamic interfaces on WLC 4402

    Hi,
              In my company we are recently planning to get a DMZ anchor for Guest WLAN. Our setup is as following
    We have two 5508 WLCs in inside corporate network which serves for the corporate wlan. Recently we put one 4402 in DMZ in LAG mode. Two SSID has been created in 4402 namely guest and consultant. We have mobility configured perfect between these three. For the the two ssids the 4402 is the anchor.   We have created sub interfaces in ASA for management and two WLANs. The port channel is also configured proper with the native vlan for management and allowing all three vlans through it. The concern is that we cannot ping the untagged dynamic interface of WLC. The WLAN clients are getting DHCP ip perfectly on each ssid, I mean in different networks. But the clients cannot reach the gateway which is the subinterface of ASA. If I am using the webauth I am not getting redirected to the authentication page. but if I set the security to none (both L2 and L3) I can reach up to the corresponding dynamic interface and not beyond that.
    Below are my configuration details
    At switch side
    interface Port-channel1
    switchport trunk encapsulation dot1q
    switchport trunk native vlan 177
    switchport trunk allowed vlan 177-180
    switchport mode trunk
    interface GigabitEthernet2/0/26
    switchport trunk encapsulation dot1q
    switchport trunk native vlan 177
    switchport trunk allowed vlan 177-180
    switchport mode trunk
    channel-group 1 mode on
    interface GigabitEthernet1/0/26
    switchport trunk encapsulation dot1q
    switchport trunk native vlan 177
    switchport trunk allowed vlan 177-180
    switchport mode trunk
    channel-group 1 mode on
    WLC configurations
    (Cisco Controller) >show interface summary
    Interface Name                   Port Vlan Id  IP Address      Type    Ap Mgr Guest
    ap-manager                        LAG  untagged 192.168.7.3     Static  Yes    No
    management                      LAG  untagged 192.168.7.2     Static  No     No
    qd-consultant                     LAG  179      192.168.9.254   Dynamic No     No
    qd-guest                            LAG  178      192.168.8.254   Dynamic No     No
    qd-test                              LAG  180      192.168.10.254  Dynamic No     No
    service-port                         N/A  N/A      0.0.0.0               DHCP    No     No
    virtual                                 N/A  N/A      192.0.2.1           Static  No     No

    Your configuration looks good except you should assign an ip address to the service port. Never leave that at 0.0.0.0. Change that to an ip address that is non routable in your network.
    Now for your issue. Have you tried plugging in a laptop to the dmz switch in those vlans to see if it works wired. Since these are new subnets, are you sure they are being NAT'd to your public address. Check that first and let us know. The WLC should be able to ping the gateway and out into the Internet if things are setup right in the dmz.
    Sent from my iPhone

  • Force WLAN client to renew ip on WLC with dynamic interfaces

    Hi there
    we would like to have a "two tier" authentication for the corporate WLAN clients:
    Requirements
    1. Machine Authentication
    The client gets machine authenticated based on the machine account in the Active Directory with PEAP. At this stage, the client will get a IP from VLAN A. VLAN A has limited access to the corporate infrastructure (DNS, AD, some volumes / shares, and so on). The filtering is done with an IP access list on the layer 3 VLAN interface on the core switches.
    2. User Authentication
    The users logs in on the client and gets user authenticated based on his user account in the Active Directory with PEAP - only users with a valid Machine Access Restriction (MAR) are allowed to login. Now the client is moved to another VLAN B. VLAN B has full access to the corporate infrastructure, here is no IP access list.
    Infrastructure
    We have the following:
    2 x WLC 5508 with 7.3.101.0
    2 x ACS 5.3.0.40.6
    Problem
    Now we have the problem, that the Windows client sometimes takes up to 3 minutes to connect to the WLAN after the users loggs in. In the debug, I can see that this happens because the client is stuck in DHCP renewal:
    1. After the machine has been authenticated it has an IP assigned from VLAN A. This works pretty well if the client gets rebooted.
    2. If the user loggs in the first time after the reboot, the users gets connected within 10 seconds, what is pretty good. The client has now an IP in VLAN B.
    3. Now the user logs out of Windows and I can see in the debug, that the client is putted into VLAN A (machine authentication) again, but the client still tries to DHCPREQUEST the IP address from VLAN B (user authentication). Because this request is sent out on the wrong dynamic interface on WLC, the DHCPREQUEST is not acknowleged an the client get stuck in this situation.
    4. If the user or another users logs in again shortly after the logout, the client still tries to DHCPREQUEST the IP of VLAN B and now the "3 times DHCP failure on WLC" comes into play, because WLC thinks that the DHCP server is not reachable -> but it only does not answer a wrong DHCPREQUEST.
    Question
    On ISE there is a way to force the client to renew the DHCP address (via CoA, but this has its limitations too --> need to install Active X or Java applet). I think there is now way to force the client to renew its IP with ACS, but my question is, is there a workaround and are there any others, that maybe already solved this problem?
    Alternative
    If there is now way to bring this to work with two different VLAN's, I could try to realize this with only one VLAN. After the machine authentication I could apply a WLC ACL to restrict access to the corporate infrastructure. If the user authentication happens, I could "remove" this ACL to grant full access for this user / client. But I am still interested in the other solution ;-)
    Thanks in advance for any advise and best regards
    Dominic

    Your second option is what you should do. Changing the vlan on a client that already has an IP address especially on wireless will not know it has been put in a different vlan and that's why it breaks. If There was a way to change the vlan and send something to the WLC to disassociate the client, that might work.
    Sent from Cisco Technical Support iPhone App

  • Doubt with Dynamic Interfaces and VLANs

    Hello.
    I am trying to get wirelles clientes and APs to be on the same VLAN/subnet, now is working with management interface on my WLC 5508. My problem comes up when I change them to a new dynamic interface.
    Before any change:
    VLAN: 8
    Management Interface IP: 192.168.9.2/23
    Gateway: 192.168.8.1
    DHCP Server: 192.168.8.2
    WLAN SSID linked to Managment interface: Ray123
    APs on VLAN 8 and subnet static IP range192.168.9.0/23
    There is no dynamic interface.
    After changes.
    VLAN: 0
    Management Interface: 192.168.6.2/23
    Gateway: 192.168.6.1
    DHCP Server: 192.168.6.2
    Dynamic interface name: Wireless-1
    VLAN: 8
    Management Interface IP: 192.168.9.2/23
    Gateway: 192.168.8.1
    DHCP Server: 192.168.8.2
    WLAN SSID linked to Dynamic interface: Ray123
    APs still on VLAN 8 and subnet static IP range192.168.9.0/23
    After all this done i can see by cdp neighbors all my APs i can ping them and management interface too, but APs are not registered, no clients too.
    According to this guide:
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00805e7a24.shtml
    Dynamic interfaces and APs should be on the same VLAN.
    But this another guide states the opposite:
    http://www.cisco.com/en/US/docs/wireless/controller/7.0/configuration/guide/c70mint.html
    "Set the APs in a VLAN that is different from the dynamic interface configured on the Controller. If the APs are in the same VLAN as the dynamic interface, the APs are not registered on the Controller and the 'LWAPP discovery rejected' and 'Layer 3 discovery request not received on management VLAN' errors are logged on the Controller"
    I cant understand why VLANs for APs and dynamic interfaces should be on different, it has no sense to configure a vlan intended for APs which shouldnt be on the same vlan.
    Please tell me what is wrong.
    Thanks in advance.

    You have to tell the APs where the WLC lives now, 192.168.6.2.
    You can do this in the following ways:
    Manual Prime the APs
    option 43
    dns
    ip forward udp 5246
    move the aps to the same vlan as the management interface let them join and then chnage the vlan
    "Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
    ‎"I'm in a serious relationship with my Wi-Fi. You could say we have a connection."

  • Wireless lan Controller 4402 / ping dynamic interface failed

    hi,
    i've a problem with a Wireless Lan Controller 4402.
    When i configure the dynamic interface on the my network , with wired lan
    i don't reach (i use the ping command) the ip address of the WLC.
    In my case (wired):
    On my pc i've a ip 10.1.78.1 255.255.0.0 and dgw 10.1.1.1 (vlan721)
    The lan WLC have a ip of management 10.12.2.4 /24 (vlan799) [dgw 10.12.2.1]
    dynamic vlan 792 ip add 10.12.78.100 / 22 (vlan792) [dgw 10.12.68.1]
    i ping these interfaces (10.12.2.4 and 10.12.78.100) and the ping is ok.
    When i create a dynamic interface vlan 721 starting the problem:
    dynamic vlan 791 ip address 10.1.1.240 / 16 (vlan721)
    After this ......the ping on 10.12.2.4 and 10.12.78.100 don't respond very well
    and i lose the 80-90% of the ping packages.
    through the wi-fi instead I do not have problems.
    the problem exist only via wired (cable).
    Can you help me?
    Thanks
    FCostalunga

    Hello,
    Pinging the dynamic interface is officially not supported. The reason why is because the controller places a very low priority on ICMP traffic. Typically, you will not have an issue with doing so on your wireless network because this interface is basically a gateway for the client. However, from the wired network - the only interface designed to respond to pings 100% of the time is the management interface. Hope this helps!
    -Mark

  • Getting Type Mismatch Error while passing Array of Interfaces from C#(VSTO) to VBA through IDispatch interface

    Hi,
    I am facing issues like Type Mismatch while passing Array of interfaces from .NET  to VBA and vice versa using VSTO technology.
    My requirement is that ComInterfaceType needs to be InterfaceIsIDispatch.
    My Interface definition is somewhat like this
        [ComVisible(true)]
        [InterfaceType(ComInterfaceType.InterfaceIsIDispatch)]
        [Guid("AAF48FBC-52B6-4179-A8D2-944D7FBF264E")]
        public interface IInterface1
            [DispId(0)]
            IInterface2[] GetObj();
            [DispId(1)]
            void SetObj(ref IInterface2[] obj);
        [ComVisible(true)]
        [InterfaceType(ComInterfaceType.InterfaceIsIDispatch)]
        [Guid("CDC06E1D-FE8C-477E-97F1-604B73EF868F")]
        public interface IInterface2
    IF i am passing array of above interface (created in C#.Net) to VBA using GetObj API,i am getting type mismatch error in VBA while assigning the value to variable in VBA.Even assigning to variant type variable gives TypeMismatch.
    Also while passing Array of interfaces from VBA using SetObj API,excel crashes and sometimes it says method doesn't exists.
    Kindly provide some assistance regarding the same.
    Thanks

    Hi,
    I am facing issues like Type Mismatch while passing Array of interfaces from .NET  to VBA and vice versa using VSTO technology.
    My requirement is that ComInterfaceType needs to be InterfaceIsIDispatch.
    My Interface definition is somewhat like this
        [ComVisible(true)]
        [InterfaceType(ComInterfaceType.InterfaceIsIDispatch)]
        [Guid("AAF48FBC-52B6-4179-A8D2-944D7FBF264E")]
        public interface IInterface1
            [DispId(0)]
            IInterface2[] GetObj();
            [DispId(1)]
            void SetObj(ref IInterface2[] obj);
        [ComVisible(true)]
        [InterfaceType(ComInterfaceType.InterfaceIsIDispatch)]
        [Guid("CDC06E1D-FE8C-477E-97F1-604B73EF868F")]
        public interface IInterface2
    IF i am passing array of above interface (created in C#.Net) to VBA using GetObj API,i am getting type mismatch error in VBA while assigning the value to variable in VBA.Even assigning to variant type variable gives TypeMismatch.
    Also while passing Array of interfaces from VBA using SetObj API,excel crashes and sometimes it says method doesn't exists.
    Kindly provide some assistance regarding the same.
    Thanks

  • Issue in moving files from data fodler to processed folder in background

    Hi All,
    I am facing one issue in moving files from data fodler to processed folder in case of background execution.
    When i am executing the file in the foreground, i can move the file from Data folder to processed folder. I am using SXPG_COMMAND_EXECUTE FM to move the file from data folder to processed folder.  I can see the file in processed folder once the program is executed.
    But in case of executing the same program in background, it is giving me the error "Failed to move the file to processed folder" in the spool of SM37 and i can see the file still laying in data folder.
    I tried to check other programs which acesses the same folder as the above program, whether they are able to move. They are able to move the file to processed fodler successfully both in foreground and background mode.
    Please help me in resolving this issue.
    Thanks,
    Deepa

    Hi Sanu,
                    Please use teh following code to move the file from source to target folder.
    This is a code showing how to create and use COPY command of UNIX in ABAP
    PARAMETERS:
    Input file path
    p_input TYPE localfile,
    Processed file path
    p_proc TYPE localfile.
    Declare the Types to file data
    TYPES: BEGIN OF L_X_OUTPUT,
    sys(200), " Please note, there are asterisk before and after sys (i.e.sys)
    END OF L_X_OUTPUT.
    * Internal table to store file data
    DATA l_i_output TYPE STANDARD TABLE OF l_x_output WITH HEADER LINE.
    * Variable for the UNIX command
    DATA: l_v_unix_comm(255) TYPE c.
    Copy command of UNIX
    CONCATENATE 'mv' p_input p_proc
    INTO l_v_unix_comm SEPARATED BY space.
    For example the Copy command is stored as below
    cp u2018/data/interfaces/input/input_fileu2019 u2018/data/interfaces/processed/processed_fileu2019
    Examples of UNIX Command *u2022 mv filename1 filename2 --- moves a file (i.e. gives it a different name, or moves it into a *different directory (see below) *u2022 cp filename1 filename2 --- copies a file
    Execute the UNIX Copy command.
    This command will copy the file from input file path to the processed file path
    CALL 'SYSTEM' ID 'COMMAND' FIELD l_v_unix_comm
    ID 'TAB'
    FIELD l_i_output-sys.
    IF sy-subrc eq 0.
    write: 'File is copied successfully using UNIX command in ABAP'.
    ENDIF.

  • Dynamic interface port assignment

    Good Day,
    I am setting up a 4402 (50 ap license ver 5.0) that will manage about 40 aps. Following the Cisco docs, I have created two ap manager intefaces for load balancing. Each physical port is attached to one of two Cat 6509s (no lag).
    Our network ultimately connects to a router (over which I have no control) with six 100 mps ports each representing a subnet/vlan. So my intent is to create six dynamic interfaces each coresponding to a vlan for load balancing and bandwidth optimization.
    My question regards assinging each dynamic interface to a physical port. Simple logic would have me assinging 3 interfaces to port #1 and three to port #2, then assigning a proportionate number of aps to each interface.
    Is it that simple, or are there other considerations.
    Thanks

    You're correct. Creating a dynamic interface for each VLAN is exactly what you need to do. This will load-balance the traffic from the multiple VLANs across your links.
    I would highly recommend that you consider LAGging the two uplinks. It provides better load-balancing and better redundancy. Since you're connecting to a 6509, you can LAG between two blades for redundancy purposes.
    Whether you LAG or not is completely up to you, of course. But you seem to be good to go if you want to leave them unLAGged.
    Jeff

  • WLC Dynamic Interface

    I wonder why we need Dynamic Interfaces. I have created two WLANs. One is WPA2-Enterprise obtaining vlan id's per user from Radius server and the other WEP wlan for guest users whose traffic should go to a specific guest vlan. I am using an external DHCP server and configured WLC not to proxy dhcp requests and to act as a bridge.
    I had to create dynamic interfaces on WLC (we are using 5508 with software version 7) for all the VLANs which radius server returns. I could make it with only defining the dynamic interfaces and entering 0.0.0.0 for ip addresses.
    For the other WLAN with WEP, I have to enter and IP for the dynamic interface to work. I am not sure if this is a requirement or my misconfiguration, but I do want a way not to set an IP address for the dynamic interface. I do not want to waste addresses and also do not want the clients to be able to access wlc through that IP address.
    I appreciate any comment on why I need IP addresses for dynamic interfaces.

    Vadood... The WLC does use that IP address as it needs to have layer 2 connection to any subnet it will place users on. Even is your doing AAA override, the radius tell the WLC that that device needs to be on vlan x and the WLC will put that device on vlan x, but if the WLC has no IP address on that subnet, well then the communication stops there. The user will never get an IP address if using dhcp or if the device has a static, the WLC has no way to communicate to that subnet.
    By the way, users can't access the dynamic interface by default. You have to enable that. But then again, they can try to access the management interface also, unless you disable globally management over wireless.
    Sent from Cisco Technical Support iPhone App

  • Possible to set Dynamic Config from ABAP Proxy

    Hi,
    I know how to get and set Dynamic Config from Java/XSLT mappings and adapter modules. But I want to do this from an outbound ABAP Proxy Call (in the same way I can set the serialization context for EOIO), is that possible?
    The scenario is: I have an interface; Proxy -> Xi -> ftp, with no mapping. It seems unnecessary to introduce a mapping just to set some dynamic config values for the receiving adapter which are already known at the outbound proxy call...
    rgds Johan

    Hi Bhavesh,
    In the thread you mention it is shown that you can set Dynamic Config properties during an ABAP mapping. My question was if I can set these properties already in the proxy call? Or did I miss something?
    Of-course I can introduce a dummy mapping in Java/XSLT/ABAP which copies the source message to the result message and sets the dynamic config properties, but I would rather not introduce a mapping if not neccessary...
    rgds Johan

Maybe you are looking for