Issue on urgent priority short dialing intra cluster

Hello All,
I have an issue with short daling within the cluster, It seems CUCM takes 6 seconds to make the second phone ring even when a TP with urgent priority is hit. As fas as my observation appropriate translation pattern hit and it actions as soon as the user presses the digits, but cucm takes time in searching the called number and it finds the number only after 6 seconds and the phone rings. There is no issues with enblock dialling.
Configuration: CUCM 8.5.1
ANI : 3573257
DNIS : 3573258
* Cisco 7942 (3573257 in partition2 dialls 3 2 5 8) --> 3XXX TP with urgent priority, prefix 357 in partiotion1 --> Cisco 7942 (3573258 in partition2 phone rings after 6 seconds)
* Both the phone are under the same subscriber.
* If I do enblock dialling I dont see any issues.
Changes happened:
The issue happened after the site has been undegone some phones, partiotion, CSS and gateway changes with regard to implementing logical partitioning.
Kindly help me on this issue, earlier called phone rings as soon as the user do 4 digit short dial but now it has 6 seconds delay. I can post if you need the CCM traces here.

I checked your traces.
in Enbloc dialing there is no potential match exist during digit analysis.
21:59:35.734 |StationInit: (0146365) EnblocCall calledParty=3257.|8,100,50,1.933363045^19.237.142.74^SEP001E13E61F14
21:59:35.735 |Digit analysis: match(pi="2", fqcn="66553077", cn="3573077",plv="5", pss="SG2-ICR-BSpecial-PT:SG2-ICR-Emergency-PT:SG2-ICR-DNTrans-PT:SG2-ICR-PSTN-FAC-PT:SG2-ICR-CMService-PT:SG2-TCM-InTrans-PT:SG2-TCM-PT:SG2-VM-PT", TodFilteredPss="SG2-ICR-BSpecial-PT:SG2-ICR-Emergency-PT:SG2-ICR-DNTrans-PT:SG2-ICR-PSTN-FAC-PT:SG2-ICR-CMService-PT:SG2-TCM-InTrans-PT:SG2-TCM-PT:SG2-VM-PT", dd="3257",dac="0")|8,100,50,1.933363045^19.237.142.74^SEP001E13E61F14
21:59:35.735 |Digit analysis: analysis results|8,100,50,1.933363045^19.237.142.74^SEP001E13E61F14
21:59:35.735 ||PretransformCallingPartyNumber=3077
|CallingPartyNumber=3077
|DialingPartition=SG2-ICR-PhoneDN-PT
|DialingPattern=3573257
|FullyQualifiedCalledPartyNumber=66553257
|DialingPatternRegularExpression=(3573257)
|DialingWhere=
|PatternType=Enterprise
|PotentialMatches=NoPotentialMatchesExist
but for the digit by digit dialing, it says, potential matches exist.
21:59:50.906 |Digit analysis: match(pi="2", fqcn="66553077", cn="3573077",plv="5", pss="SG2-ICR-BSpecial-PT:SG2-ICR-Emergency-PT:SG2-ICR-DNTrans-PT:SG2-ICR-PSTN-FAC-PT:SG2-ICR-CMService-PT:SG2-TCM-InTrans-PT:SG2-TCM-PT:SG2-VM-PT", TodFilteredPss="SG2-ICR-BSpecial-PT:SG2-ICR-Emergency-PT:SG2-ICR-DNTrans-PT:SG2-ICR-PSTN-FAC-PT:SG2-ICR-CMService-PT:SG2-TCM-InTrans-PT:SG2-TCM-PT:SG2-VM-PT", dd="3257",dac="0")|8,100,50,1.933364937^19.237.142.74^SEP001E13E61F14
21:59:50.906 |Digit analysis: analysis results|8,100,50,1.933364937^19.237.142.74^SEP001E13E61F14
21:59:50.906 ||PretransformCallingPartyNumber=3077
|CallingPartyNumber=3077
|DialingPartition=SG2-ICR-PhoneDN-PT
|DialingPattern=3573257
|FullyQualifiedCalledPartyNumber=66553257
|DialingPatternRegularExpression=(3573257)
|DialingWhere=
|PatternType=Enterprise
|PotentialMatches=PotentialMatchesExist
|DialingSdlProcessId=(0,0,0)
|PretransformDigitString=3573257
|PretransformTagsList=SUBSCRIBER
|PretransformPositionalMatchList=3573257
|CollectedDigits=3573257
|UnconsumedDigits=
not sure why this difference is? could you please crosscheck the routeplan report once again please?

Similar Messages

Hi there!! this issue is urgent

My question in english:
Hi there!! this issue is urgent,
I get an error on this page www.kinogonzalez.com in the comercials section.
Doesn´t work When i want to make an scroll of the thumbnails with the wheel of the mouse.
If you look in other browsers such as Firefox, explorer, this error does not happen, which may be wrong??
Thank you so much.
Mi duda en español:
Que tal me urge mucho este tema, me da un error en esta página al querer hacer un scroll de los thumbnails con la ruedita del mouse.
Si se fijan en otros navegadores, como firefox, explorer, este error no sucede, que podra ser?
Muchisimas Gracias.
Agustin
<Edited by Moderator>

Hello a:
Some web developers do not write code to standards or, worse yet, write to IE specifications.
Contact the web site technical people for further information.
Barry

CATS Issue VERY Urgent..

HI ALL,
BiW PROD is placing CATS data for 2007 in to week 52 2006. Can advise why?
Please advise what would be the error.
Cheers,
Sri

Hi All,
We have a problem for 0CALWEEK in CATS.
FOR 0CALQUARTER
20061 means 1st quarter
20062 means 2ND quarter
20063 means 3RD quarter
20064 means 4TH quarter
FOR 0calweeK:
20061 means 1st WEEK
20062 means 2ND WEEK
20063 means 3RD WEEK
20064 means 4TH WEEK
0CALWEEK is giving problem IN CUBE.
It shows wrongly.
0CALQUARTER      0CAL WEEk
2007 1             2006 52 ( 52 week)
2007 1                          2006 52
<b>0CAL WEEk          should show 2007 1     instead of 2006 52.</b>
It should show :
0CALQUARTER      0CAL WEEk
2007 1             2007 1 (ist week in 2007)
2007 1                         2007 1
we have a routine on 0CAL_week
=====
PROGRAM UPDATE_ROUTINE.
$$ begin of global - insert your declaration only below this line -
TABLES: ...
DATA:   ...
data:   employee_md like /bi0/memployee,
        employee_wa like /bi0/memployee,
        person_md   like /bi0/mperson,
        PERSON_WA   LIKE /BI0/MPERSON.
DATA:   G_RECORD_NO LIKE SY-TABIX.
INCLUDE RS_BCT_HR_UPDATE_RULES_GENERAL.
INCLUDE RS_BCT_HR_PAPA_UPDATE_RULES.
$$ end of global - insert your declaration only before this line   -
FORM compute_characteristics
TABLES   MONITOR STRUCTURE RSMONITOR "user defined monitoring
USING    COMM_STRUCTURE LIKE /BIC/CS0CATS_IS_1
           RECORD_NO LIKE SY-TABIX
           RECORD_ALL LIKE SY-TABIX
           SOURCE_SYSTEM LIKE RSUPDSIMULH-LOGSYS
CHANGING RESULT LIKE /BIC/VZCATST-CALWEEK
           RETURNCODE LIKE SY-SUBRC
           ABORT LIKE SY-SUBRC. "set ABORT <> 0 to cancel update
$$ begin of routine - insert your code only below this line        -
fill the internal table "MONITOR", to make monitor entries
data: w_date type d.
data: w_date_check type d.
data: w_numberofdays type p decimals 2.
data: w_numberofweeks type i.
data: w_dayofweek type p.
data: w_first_day_of_sap_calendar type d value '19790101'.
data: check type i.
data: w_year(4) type c.
data: w_weekno(2) type c.
w_date_check = COMM_STRUCTURE-CALDAY.
w_date = w_date_check.
w_date+04(04) = '0101'. " beginning of the year
do.
w_dayofweek = ( ( w_date - w_first_day_of_sap_calendar ) mod 7 ) + 1.
if w_dayofweek = 7. " First sunday(7) of the Current year
exit.
endif.
add 01 to w_date+07(01).
enddo.
w_numberofdays = ( w_date_check - w_date ) + 1.
w_numberofweeks = ceil( w_numberofdays / 7 ).
w_year = w_date_check+0(4).
if w_numberofweeks = 53.
    w_numberofweeks = 1.
    w_year = w_date_check+0(4) + 1.
endif.
if w_numberofweeks = 0.
    w_numberofweeks = 52.
    w_year = w_date_check+0(4) - 1.
endif.
w_weekno = w_numberofweeks.
call function 'CONVERSION_EXIT_ALPHA_INPUT'
     exporting
          input   = w_weekno
    importing
         output = w_weekno.
concatenate w_year w_weekno into RESULT.
result value of the routine
RESULT = .
if the returncode is not equal zero, the result will not be updated
RETURNCODE = 0.
if abort is not equal zero, the update process will be canceled
ABORT = 0.
$$ end of routine - insert your code only before this line         -
ENDFORM.
========
This is giving problem from 2007 year only.
We need to check with FI or HR teams , Is there any configuration settings in R/3 side for 0Calweek?
This is production ISSUE. Help me on very Urgent BASIS!!
Thanks & Regards,
Sri.

Reporting issue (very urgent)

Sr.No     Flt.NO     ORI- DES     Total Flts     TS OFF     FC     KC     TS Util      FC
1     IT101     BOM-BLR        20     2,680     400     2,280     2,165     230
2     IT103     BOM-BLR        20     3,216     480     2,736     2,322     245
5     IT111     BOM-BLR        24     3,216     480     2,736     2,396     159
Result           BOM-BLR        64     9,200     1,360     7,800     6,900     615
6     IT102     BLR-BOM        20     2,680     400     2,280     2,222     140
9     IT110     BLR-BOM        20      3,216     480     2,736     2,543     257
10     IT112     BLR-BOM        24     3,216     480     2,736     2,257     168
Result          BLR-BOM        64     9,200     1,360     7,800     7,100     530
Overall Result    BOM-BLR-BOM       128     18,400     2,720     15,600
Hi all,
          I have the above issue like am working on BI7 reporting and i want a monthly report and the report should be like above.The user want to see the result of each segment in the next row.And after two result rows, one over all result of the two.
When I put a filter in the report then i can see the subresult of single segment but am not able to see the rest of the Segments.It is just showing the filtered segment with the subresult. I want to see all the segments with the subresult and overall result rows.
Can it possible in the report if it is then Plz tell me how to do that.Its urgent
Ensuring points
Thanking

I guess ORI-DES is a characteristic. if yes then, Ori-des should come before Flt. NO. and in properties->display, result rows should be 'Always display' to get desire result

Query Issue(Very Urgent)

Hi,
     I have issue with select statement to pull the records from two tables. Here I have two tables one is with Billing Document Items and Service Order Operations.
I have service order as unique field in both tables, When I execute select statement with one service order I got 10 records like
S Ord Oper                           Billing Document Items
Oper    Repair Code                 Item    Oper    Repair Code
10        AD01                           1         10        AD01
20        AD01                           2         20        AD01
30        OT01                           3         10        AD01
40        RE01                           4         20        AD01
50        RP01                           5         20        AD01
                                               6        20         AD01
                                                7        30         OT01
                                                8        40         RE01
                                                9        50         RP01
                                               10      50         RP01
             This are the records with same Service order number, and my select statement giving data like
O/P
Service Order = 60001212
OPER    ITEM    REPAIR TYPE
10         1           AD01
20         1           AD01
10         2           AD01
20         2           AD01
10         3           AD01
20         3           AD01
10         4           AD01
20         4           AD01
10         5           AD01
20         5           AD01
10         6           AD01
20         6           AD01
30         7           OT01
40         8           RE01
50         9           RP01
50         10         RP01
But I need output like this
Item Oper                   Rep Code
1      10                      AD01
2      20                      AD01
3      10                      AD01
4      20                      AD01
5      20                      AD01
6      20                      AD01
7      30                      AD01
8      40                      RE01
9      50                      RP01
10    50                      RP01
         Please give me the select statement which gives the above output. I need very urgent please....
Thanks
Robbie

hi robert,
The ouput u want is just a little away from the one u r actually getting. it is the two fields OPER and ITEM interchangeably..
U just have to use GROUP BY ITEM..........if u want the desired output with ITEM as first field.
<group-by-clause> → GROUP BY [<column-ref>,*]<column-ref>
if it helps please reward points.
thanks

Attachment issue --very urgent help required

Hello friends,
1)i have create page and deatal page . requirement is that we have to load required attachments in table region, if not loading required attachments exception will raise. this validation is working fine in create page.
2)same in detail page i loaded required attachments also excepiton is raising.
waht would be cause. i am very new to ADF technology.
very urgent to fix this issue. any one help me out.
Thanks,
vamshi.
Edited by: Krishna Vamshi on Jul 1, 2010 6:14 PM

Kirshna,
Unfortunately your question is very unclear.
Let me say that if you are asking about OA Framework, you should ask on the OA Framework forum, not here.
also excepiton is raising.It will help if you say what the exception is.
John

Issue Undeploying and Deployment Application in Weblogic Cluster

We have a production environment wich has one cluster with 40 servers in it. The problems lies when we select one application to undeploy. Weblogic response in administration console says that the undeploy is finished, but when I try to deploy another version of the application it only affect one of the 40 servers of the cluster, the other 39 servers are still with the old version of the application in memory.
If I restart all the servers it works and all the 40 server get the new version of the application.
Now we want to do continuous deployment and scripting all the deploy process and we don't want to restart all the 40 servers every deploy.
Is there any limit of servers in a cluster? I'm saying this because it didin't occur in the stage environment with one cluster with 5 managed servers.
Do I need any specific node manager configuration to undeploy this 40 managed servers?
I look in the internet and didin't find any issues related to this.

Sharmela,
Looks like the undeploy command did not clean up the stage directories of the managed server properly.
There is no limit on the number of managed servers in a cluster or in a domain. But again you need to plan the number based on the hardware and memory settings.
We have two hexalogics, the problem here is not hardware.
Do I need any specific node manager configuration to undeploy this 40 managed servers?
What exactly you mean by undeploying managed server ? You want to remove them or bring them down ?
Sorry about that, I want to know what should I do to undeploy the application properly in the 40 managed servers(not bringing them down). I've heard something about staging mode but i've already tried to put ---nostage paramenter and the result was the same.
Do you have any clue why weblogic is not cleaning the stage directories? Is there any way to force it without restarting all the servers?
Thank you very much,
Gustavo

SPA 3102 & SPA2102 have too short dial tone time.

My 3102 has an "off hook" time of about 9 seconds before it times out if no key is pressed. This is usually OK, but my 2102 only gives me 3 seconds, which is definitely not enough.
I found in the Linksys "ATA Administration Guide v3 200809" :- ftp://ftp.linksys.com/downloads/NA/other/ATA_AG_v3_200809_AdminGuide.pdf
Syntax for the Dial Plan Timer
SYNTAX:
(Ps<:n> | dial plan )
s: The number of seconds; if no number is entered after P, the default timer of 5
seconds applies.
I have added this Ps command to my dial plans but while I can reduce the timer period, I can not increase them.
Both ATA's have the latest firmware installed and work as required in other ways.
Is their something else to be adjusted?

The regional tab:-
Call Progress Tones
Dial Tone:
Second Dial Tone:
Outside Dial Tone:
Prompt Tone:
Busy Tone:
Reorder Tone:
Off Hook Warning Tone:
All show ;10( as you suggested, but I've tried various longer and shorter times for both "Dial Tone" and "Reorder Tone" but no change from the 3 second timeout.I wondered whether the Reorder Delay which was set at 3, could be the problem, so changed to 10 with no effect.
Control Timer Values (sec)
Hook Flash Timer Min:
Hook Flash Timer Max:
Callee On Hook Delay:
Reorder Delay:
In case it is relevant, my dial plan is:-(13[1-9]xxxS0|1[38]00xxxxxxS0|190xx.!|0011xx.!|0[2-9]xxxxxxxxS0||<9:089>xxxxxxxS0 |<:089574>[2-8]xxxS0 )My software Version is 5.2.10It may be relevant that after the Dial Tone times out (in 3 sec) I do not get Reorder Tone but it just goes dead!RegardsMaurice

Plz help to solve my issue its urgent

Hi,
my user uploaded invoice,debit memos and credit memos transactions.
after uploading she had done auto invoice.
invoice and debimemos auto invoice was completed successfully but credit memos she got an error.
again she did auto invoice for credit memos,then it was completed but with zero records.
actually there are two records for credit memos.
please help me.
this is an urgent issue.
im getting error due to auto invoice
APP-AR-11526: ORA-01427: single-row subquery returns more than one row
UPDATE RA_INTERFACE_LINES L1
SET REQUEST_ID = :b1,
LAST_UPDATE_DATE = !
APP-AR-11526: 3966142/ar/src/autoinv/raamil.lpc 1333
UPDATE RA_INTERFACE_LINES L1
SET REQUEST_ID = :b1,
LAST_UPDATE_DATE = sysdate,
LAST_UPDATED_BY = :b2,
LAST_UPDATE_LOGIN = :b3,
CUSTOMER_TRX_ID = NULL,
INTERFACE_LINE_ID = NVL(INTERFACE_LINE_ID,
RA_CUSTOMER_TRX_LINES_S.NEXTVAL),
SET_OF_BOOKS_ID = NVL(SET_OF_BOOKS_ID, :b4),
LINK_TO_LINE_ID =
SELECT INTERFACE_LINE_ID
FROM RA_INTERFACE_LINES L2
WHERE L2.REQUEST_ID = :b5
AND L2.INTERFACE_LINE_CONTEXT = 'TTAS'
AND L1.LINK_TO_LINE_CONTEXT = L2.INTERFACE_LINE_CONTEXT
AND L1.LINK_TO_LINE_ATTRIBUTE1 = L2.INTERFACE_LINE_ATTRIBUTE1
AND L1.LINK_TO_LINE_ATTRIBUTE2 = L2.INTERFACE_LINE_ATTRIBUTE2
AND L1.LINK_TO_LINE_ATTRIBUTE3 = L2.INTERFACE_LINE_ATTRIBUTE3
AND L1.LINK_TO_LINE_ATTRIBUTE5 = L2.INTERFACE_LINE_ATTRIBUTE5
WHERE NVL(INTERFACE_STATUS, '~') != 'P'
AND (REQUEST_ID IS NULL OR REQUEST_ID IN (:b6)
AND EXISTS
SELECT 'x'
FROM RA_INTERFACE_LINES L2
WHERE L2.REQUEST_ID = :b7
AND L2.INTERFACE_LINE_CONTEXT = 'TTAS'
AND L1.LINK_TO_LINE_CONTEXT = L2.INTERFACE_LINE_CONTEXT
AND L1.LINK_TO_LINE_ATTRIBUTE1 = L2.INTERFACE_LINE_ATTRIBUTE1
AND L1.LINK_TO_LINE_ATTRIBUTE2 = L2.INTERFACE_LINE_ATTRIBUTE2
AND L1.LINK_TO_LINE_ATTRIBUTE3 = L2.INTERFACE_LINE_ATTRIBUTE3
AND L1.LINK_TO_LINE_ATTRIBUTE5 = L2.INTERFACE_LINE_ATTRIBUTE5
Error calling raamil()
Error calling raapft()
raafds()+ Current system time is 17-DEC-2008 15:42:22
raafeb()+ Current system time is 17-DEC-2008 15:42:22
raafeb()- Current system time is 17-DEC-2008 15:42:22
raafds()- Current system time is 17-DEC-2008 15:42:22
Start of log messages from FND_FILE
End of log messages from FND_FILE
No completion options were requested.
Concurrent program returned no reason for failure.
Concurrent request completed
Current system time is 17-DEC-2008 15:42:22
this im getting because in the query im must add one line l2.mtl_system_items_seg1=l1.mtl_system_items_seg1
but this is autoinvoice program and the executable method for this program is SPAWNED and in d:\oracle\prodappl\ar\11.5.0\bin\raxtrx.exe or raxtrx.map
but nopw how can i modify the query please help me.
please its an urgent issue.
Edited by: user649793 on Dec 18, 2008 8:01 PM

You don't need to keep posting different threads.
There's nothing we users here can do for you if you brought your phone into a LEGITIMATE authorized service center in your area and they're telling you there is no problem.
Contact Apple customer service and see if they can do anything for you.

Production Issue Need urgent help

We just added new disk on our db box. its sun 890 box after that the DB is running very slow and the cpu is showing 100% is there any way we can find out the cause of the issue.
Any assistance will be highly appreciated.

Check with the OS monitoring tools. You should provide the OS and DB versions in your thread so a more proper direction on the recommended tools can be provided.
If you are on 10g you could use the performance monitor from the EM DB Console and you could see if Oracle is responsible for this high CPU consumption.
By the way. I kindly suggest you to use a more descriptive thread title, 'Urgent' and 'Production Issue' doesn't let any body figure out what you are talking about. On the other hand, labeling urgent won't make all posters go running to solve this issue, all threads are treated equally on a first come first served basis and it depends on posters availability.
~ Madrid

HP Envy 17 3D 1201tx issues, need urgent help

I had purchased HP Envy 17 3D 1201tx notebook back in March 2011, but could hardly use it due to some personal problems at my end. However, after 8 months of the purchase, when i used it, I found the BDROM drive was not working, and later on the internal cooling fan also stopped working. As, I said, due to personal problems I could not contact HP, and the laptop was not again in use for many months.
I had just about six months back started gettings SMART failure of HDD, and the hard drive gave way as well (sic).
I've contacted HP just few months back to get a paid service, but rather giving service, they misbehaved. I'm now seeking help on HP support forum, please help me getting past the issues with this expensive laptop.
issues:
1. BDROM drive would not recognize/read any writable or re-writable CD/DVD and it only recognizes read-only CDs.
My query is "is the optical drive dead or service able?"
2. Internal cooling fan is not working. Is it service able, can you guide me "how to open the laptop", so I can service or replace the cooling fan with a new one myself?
3. Internal 640 GB Toshiba HDD that came with the laptop is dead now. I have selected the following two, can you advise, which is the best between the two:
a. WD 1 TB LaptopInternal Hard Drive(WD10JPVT/WD10JPVX)
b. Seagate Solid State Hybrid Drive 9.5 mm thickness 1 TB Laptop Internal Hard Drive (ST1000LM014)
4. I also want to upgrade the RAM from factory installed 4 GB to 8 GB. Can you please advise me the dual channel RAM modules (i.e. 4x4 GB) compatible with Envy 17 3D 1201tx.
May, I request the experts here, to please suggest me the best of the compatible RAM for my laptop, so I get the maximum performance from my laptop. And, also the technical details of the factory installed RAM.
I'm live in Delhi, India.
Thanks in advance.

Bdrom probably dead. Can buy a replacement one off eBay easy enough. Replacement normally only one or two screws.
Personally I would go for seagate drive but western digital will be fine so long as you have the recovery media.
Disassembly of laptops can be tricky if you are new to it. Too long to explain here but Google for a service manual for your unit or a YouTube video. With patience and a good screwdriver it's not too much trouble.
Depending on what's wrong with the fan (man be just clogged with dust) you may need a replacement. Look for spares on ebay or spares supplier.
Ram should be easy to find out, Google the part number or check the bios. You can check the manual for compatible ram or try Kingston/crucial ram checker database (not guaranteed but rarely wrong)

AD-Exchange Connector versions Incompatibility Issues : Extremely URGENT

Hi,
We have tested our code in dev environment (AD, Exchange versions 2003). But in production env, the root context for the two are different from those of dev environment.
In dev env: root context are: DC=company,DC=devxyz for ADITResource,Exchange
In prod env: root context are: DC=company,DC=devxyz for ADITResource ; DC=devxyz for Exchange.
Exchange being dependent on AD, when AD is provisioned, Exchange fetches the ObjectGUID of AD User, and searches in parent root context (DC=devxyz) which return some garbage value -50 corresponding to null value. SInce ObjectGUID is not fetched, Exchange cannot be provisioned.
Please give some pointers for this issue. It is very critical at this stage as we cannot do any changes in the existing configurations.
Regards,
Deepika

Exchange fetches the ObjectGUID of AD User, and searches in parent root context (DC=devxyz) which return some garbage value -50 corresponding to null value. SInce ObjectGUID is not fetched, Exchange cannot be provisioned.If it is facing issue only with objecrGUID then You can write your custom JNDI code to fetch this value and update in some field.
Just make a task in Exchange Process Definition which will do this thing.

Mavericks MAJOR Issues - HELP URGENT

Dear Sir,
First of all below is my Macbook Pro specifications:
Processor 2.2GHz Intel Core i7
Memory 16GB 1333 MHz DDR3
Graphics Intel HD Graphics 3000 512MB
Hard Disk 750 GB
Software OS X 10.9
Second below are my issues after Upgrading to Mavericks:
1 - A REALLY noisy FAN while working on my macbook editing a single picture with PS CC or Lightroom.
2- Inactive Memory drains my Memory Usage and I Slows down my laptop.
3- I cannot Preview my Picture folder "All at .TIF format" Like before thus i have to Open them Via Preview which is taking ALOT Of time or via "Preview" - Yes all my TIF files are opened via Preview as a Default program but yet the Thumbnails not showing the preview pictures even though i have the tick on "Show Icon preview" .
My Macbook pro is only 1 year old and i am really annoyed with all this as i have spent a huge MONEY on it! please i need help regarding the 3 issues above!

Dear Sir,
First of all below is my Macbook Pro specifications:
Processor 2.2GHz Intel Core i7
Memory 16GB 1333 MHz DDR3
Graphics Intel HD Graphics 3000 512MB
Hard Disk 750 GB
Software OS X 10.9
Second below are my issues after Upgrading to Mavericks:
1 - A REALLY noisy FAN while working on my macbook editing a single picture with PS CC or Lightroom.
2- Inactive Memory drains my Memory Usage and I Slows down my laptop.
3- I cannot Preview my Picture folder "All at .TIF format" Like before thus i have to Open them Via Preview which is taking ALOT Of time or via "Preview" - Yes all my TIF files are opened via Preview as a Default program but yet the Thumbnails not showing the preview pictures even though i have the tick on "Show Icon preview" .
My Macbook pro is only 1 year old and i am really annoyed with all this as i have spent a huge MONEY on it! please i need help regarding the 3 issues above!

Authorization Issue - Very Urgent

Hello Guys,
I have a requirement where in I need to restrict the BI report users based on company code ( 0comp_code ).
In short, how to make the company code and plant ( 0plant ) as the authorization object and assign those to roles created.
We are using SAP BI 7.0 2004s and users will be using EP to view the reports.
I have all the roles in places for each module reports for the users.
Now I need to provide the required access authorisation based on company code and plant.
Could you please help me.
THanks and Kind Regards,
Shekar.

Authorizations - Reporting
Make 0comp_code as auth relevant from rsd1 tcode and then create auth object using RSECADMIN tcode
Hope it Helps
Chetan
@CP..

Approval issue very urgent

Hi Experts,
I knew to WF
We get the approval issue . In Ebuy of China, we have the approval workflow as go to the highest approver if the approval limit is over the default approver manager. That is User A have mgr B with limit 40,000 and mgr B have mgr C with limit 80,000. If raise a Shopping cart to 50,000, the shopping cart will go to Mgr C. User A need to add the mgr B as the first approver. But after all mgrs are added, and ordered, and back to Check status, the first 2 mgrs are disappeared. can u help on this issue?
Thanks & Regards
Vijay

Hi Nazeer,
The value of Tan(45) is beng wrongly calculated by ABAP because internally the data type for all the Trignometric functions are represented as Floating point numbers.
Please refer to this:
The results of the following functions have the data type f:
     Trigonometric functions: cos, acos, sin, asin, tan, atan
     Hyperbolic functions: tanh, sinh, cosh
     Exponential functions (base e): exp
     Natural logarithms (base e): log
     Logarithms (base 10): log10
     Square root: sqrt
In case you have any further clarifications,do let me know.
Regards,
Puneet Jhari.

Issue on urgent priority short dialing intra cluster

Similar Messages

Maybe you are looking for