Issue with cisco prime adding aceess point in the map and move in the final position
I have an Cisco Prime infrastructure with a 2.1.1 version, I created a new campus, a new building, a new floor after that i want to add access point in one floor i can add 4 access ponit but in other one floor I add first 3 access points successful bunt when i try to add a new access point in the same floor tha access point it is added but I can not move it to the final possition on the map.
the cisco prime shows the followging message
Cannot find feature by (Mac/Name/ID) null
how can I move the access point into the last possiton ?
Duplicate post.
Go HERE.
Similar Messages
-
Issues with Cisco Prime LMS 4.2.3
Hi,
I'm trailing Cisco Prime LMS 4.2.3 Soft appliance on ESXi before I deploy it into a live environment and am having some issues.
I've upgraded to version 4.2.3 and the box was working fine after the upgrade however on power it up today the Apache service will not start.
If I look at the LMS application I see this for the Apache service.
"Apache Administrator has shut down this server 0 "
I have tried to starting it.
CiscoLMS42/admin# application start Apache
% Application failed to start
CiscoLMS42/admin#
If I run an application operation debug at the same time I get the following output.
CiscoLMS42/admin# 6 [5343]: application:operation cars_install.c[1145] [admin]: Application initialization initiated for appname: Apache, operation: 0
7 [5343]: application:operation cars_install.c[1146] [admin]: Operations: O-APP_START, 1-APP_STOP, 2-APP_STATUS
6 [5343]: application:operation cars_install.c[1150] [admin]: Verifying app (Apache) is installed ...
3 [5343]: application:operation cars_install.c[1152] [admin]: App (Apache) is not installed.
3 [5343]: application:operation install_cli.c[281] [admin]: Error while starting application - Application: Apache ErrorCode: -999
I'm at a complete lose as to where to look next, failing anything else I'll have to rebuild it, but it would be nice to know how to get the Apache up and running again.
regards
RichHi Richard,
I see the following:
[ Thu Apr 18 20:53:11 GMT 2013 ] TomcatMonitor After gettingAJPPort : ajpPort = 9009 and host =CiscoLMS42
[ Thu Apr 18 20:53:11 GMT 2013 ] TomcatMonitor theMgr constructor successful.
[ Thu Apr 18 20:53:11 GMT 2013 ] TomcatMonitor Inside whileloop
[ Thu Apr 18 20:53:11 GMT 2013 ] TomcatMonitor Tomcat is not ready, it's coming up Connection refused
It looks like the hostname cannot be resolved. Can you try to add a static entry in /etc/hosts for the IP of the server and CiscoLMS42?
Restart the daemon manager and it should work.
Regards,
Vlad
==========
NMS Team
Krakow, Poland
Cisco TAC -
Autonomous to LWAPP with Cisco Prime 2.2
Hello, I need to know if exist any procedure to convert Autonomous to LWAPP access point with Cisco Prime 2.2.
Here are the Steps Cristian.
To create an autonomous AP migration template, follow these steps:
Step 1 Choose Design > Configuration > Wireless Configuration > Autonomous AP Migration Templates .
Step 2 From the Select a command drop-down list, choose Add Template, then click Go . If you are updating an already existing template, click the applicable template in the Template Name column.
Step 3 Complete the required fields. For information about the field descriptions, see: http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/2-0/reference/guide/prime_infr_ref.html
Step 4 To view the migration analysis summary, choose Operate > Wireless > Migration Analysis .
Note: After an access point has been converted to lightweight, the previous status or configuration of the access point is not retained.
Hope this will resolve your issue ;) -
MacBook and MacBook Pro with 10.6: Wireless Airport Issues with Cisco
Long Story but please bear with me:
Loaded SL on my daughters MacBook and my MacBook Pro. Internet worked flawlessly at our house (WEP encrypted) and on other public wifi. When my daughter went back to her sorority house at college 24 hours later, she could not access the internet using the sorority house network (Cisco Aironet 1800 router and Cisco Airo Access Points).
Her Airport on the MacBook appeared connected at full strength yet no internet. Two calls to Apple support (they were very nice) did not help. All the following were tried:
1. Reset PRAM
2. Deleted Airport and Safari plists
3. Edited locations
4. Removed Battery
5. Others I cannot now remember
Still no net. However, she could 'pirate' and hop on line with other identified public wifi adjacent to the sorority house. I drove to the sorority house today and tried to get on the network wirelessly using my MacBook Pro with SL. Same identical results to hers. Another MacBook without SL works great and gets right on the network.
Is this some SL influenced issue with the Airport card and the Cisco system? Weird that both of our laptops work great with several other wifi networks but not the one at the sorority house.
Could much of what we all our seeing with the internet access problem lie not with issues within our software or computers but with the routers and access points not being compatible? I have very little understanding of this stuff (as you all can probably tell) but the Apple Support people acted like it was a old firmware issue with Cisco and not with SL. Not actually what I wanted to hear.
Any ideas or suggestions?Your description there, particularly the last part, sounds like my problem. At home, we connect using Airport and ADSL which was OK, once SL had sorted out passwords.
At my office, where there are two wifi systems, I could not get on either, although did have IP numbers on both. The link to the outside world is via a proxy which uses a PAC file. Network Diagnostics reported each time (whatever I did) that the link to the server was OK, but the Internet was not.
I created a new Location with identical settings (typing them in and not copying) and the only visible difference is that the new location has no DNS numbers -- I had not noticed that before. The moment I pressed, Apply, the computer was online.
I was guessing that there was a conflict in a .plist file somewhere; but now I wonder if DNS might have been the reason (the DNS number usually used is the one from the router itself). -
Issue with cisco ONS 15310. Slot with Ethernet ports, designed for bridging.
Hi, guys. I’ve got an issue with cisco ONS 15310 sdh optical network. I’ve got a special slot with Ethernet ports, designed for bridging. Assume, we’ve got to multiplexers, named A and B with ports A0 and B0 respectively. The ios console of these slots says, the configuration is as follows:
no ip address set on these ports
Ports are administratively up
Auto mdix
Bridge groups are the same on these ports.
Dot1q tunnel.
I’m trying to monitor a device with an ip-address connected to port B0. It answers ping if I connect the notebook directly to a device. But if I connect the notebook to port A0 and ping the device pluged in port B0 through the optical network, it doesn’t answer. I tried connections with straight and cross cable.
Guys, who set the network said, it should work as a point to point bridge with no extra configuration. But it doesn’t. I used wireshark sniffer to lookup what’s happening on port A0. All I see is cdp-s from port A0 and self-announcements of the notebook.
Any suggestions? Thank you in advance.B
Building configuration...
Current configuration : 3712 bytes
! Last configuration change at
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
hostname B
boot-start-marker
boot-end-marker
enable password -
clock timezone -
ip subnet-zero
no ip domain-lookup
no mpls traffic-eng auto-bw timers frequency 0
bridge 100 protocol ieee
bridge 140 protocol ieee
bridge 141 protocol ieee
bridge 142 protocol ieee
bridge 143 protocol ieee
bridge 144 protocol ieee
interface Loopback0
ip address 192.x.0.x 255.255.255.255
interface FastEthernet0
description -
no ip address
mode dot1q-tunnel
bridge-group 140
bridge-group 140 spanning-disabled
interface FastEthernet1
description --- B0 ---
no ip address
mode dot1q-tunnel
bridge-group 141
bridge-group 141 spanning-disabled
interface FastEthernet2
description -
no ip address
mode dot1q-tunnel
bridge-group 142
bridge-group 142 spanning-disabled
interface FastEthernet3
description -
no ip address
mode dot1q-tunnel
bridge-group 143
bridge-group 143 spanning-disabled
interface FastEthernet4
description -
no ip address
mode dot1q-tunnel
bridge-group 144
bridge-group 144 spanning-disabled
interface FastEthernet5
no ip address
shutdown
interface FastEthernet6
no ip address
shutdown
interface FastEthernet7
description -
no ip address
shutdown
mode dot1q-tunnel
bridge-group 100
bridge-group 100 spanning-disabled
interface POS0
description -
no ip address
crc 32
interface POS0.1
encapsulation dot1Q 141
no snmp trap link-status
bridge-group 141
interface POS0.2
encapsulation dot1Q 142
no snmp trap link-status
bridge-group 142
interface POS0.3
encapsulation dot1Q 143
no snmp trap link-status
bridge-group 143
interface POS0.4
encapsulation dot1Q 144
no snmp trap link-status
bridge-group 144
interface POS0.5
description -
encapsulation dot1Q 140
no snmp trap link-status
bridge-group 140
interface POS1
no ip address
crc 32
interface POS1.1
encapsulation dot1Q 100
no snmp trap link-status
bridge-group 100
router ospf 100
log-adjacency-changes
network 192.x.0.x 0.0.0.0 area 0
ip default-gateway [x.x.x.x]
ip classless
no ip http server
snmp-server community public RO
snmp-server ifindex persist
snmp-server trap link ietf
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps tty
snmp-server enable traps config
snmp-server enable traps cpu threshold
snmp-server enable traps entity
snmp-server enable traps syslog
snmp-server enable traps hsrp
snmp-server enable traps config-copy
snmp-server enable traps bridge
snmp-server enable traps ospf state-change
snmp-server enable traps ospf errors
snmp-server enable traps ospf retransmit
snmp-server enable traps ospf lsa
snmp-server enable traps ospf cisco-specific state-change
snmp-server enable traps ospf cisco-specific errors
snmp-server enable traps ospf cisco-specific retransmit
snmp-server enable traps ospf cisco-specific lsa
snmp-server enable traps bgp
snmp-server enable traps pim neighbor-change rp-mapping-change invalid-pim-message
snmp-server enable traps ipmulticast
snmp-server enable traps rtr
snmp-server enable traps mpls traffic-eng
snmp-server enable traps mpls ldp
snmp-server enable traps rsvp
snmp-server enable traps l2tun session
snmp-server enable traps mpls vpn
snmp-server host x.x.x.x public
control-plane
line con 0
line vty 0 4
password -
logging synchronous level 4
login
end -
issue with cisco acs 4.2.Users unable to login aaa client but after restarting group policy able to login
issue with cisco acs 4.2.Users unable to login aaa client but after restarting group policy able to login
-
Calling issue with Cisco 7937 conference station
Hi Friends,
I am facing issue wiht Cisco 7937 conference station, our customer have various branch offices accross the world. All branches are connected over MPLS through service provider( SIP service provider) . there is a centralized CUCM and remote office have SIP Voice gateways .
When making calls from once remote site to another using Cisco 6921 phones calls working fine
When making calls from once remote site to another using Cisco 7937 conference station to make call any phone at remote office, calls are getting disconneted, remote phone rings when calls, but its gets fast busy tone when other party picks up the phone and not able to talk.
I suspect the issue with Codec but we have configured transcoders in VG and registered with CUCM
Please help me if any one experience such issue earlier.
Regards
Sivahi Basant,
1. Actually tow phones A and B are registerd with centralized CUCM, A and B are located in two different locations, RTP traffic between And B pass through service provider.
Call Flow --> Phone A ---->CUCMRouterpattern--> SIP trunk ----> Voice gateway--->Service provider cloud---> Respective Voice Gateway---> CUCM -- Phone B
Show Run
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2014.02.27 15:14:52 =~=~=~=~=~=~=~=~=~=~=~=
sh run
Building configuration...
Current configuration : 12139 bytes
! Last configuration change at 06:35:59 UTC Tue Feb 25 2014
! NVRAM config last updated at 11:16:38 UTC Mon Feb 24 2014 by administrator
! NVRAM config last updated at 11:16:38 UTC Mon Feb 24 2014 by administrator
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname eucamvgw01
boot-start-marker
boot system flash:c2900-universalk9-mz.SPA.151-4.M5.bin
boot-end-marker
card type e1 0 0
logging buffered 51200 warnings
no logging console
no aaa new-model
no network-clock-participate wic 0
no ipv6 cef
ip source-route
ip traffic-export profile cuecapture mode capture
bidirectional
ip cef
ip multicast-routing
ip domain name drreddys.eu
ip name-server 10.197.20.1
ip name-server 10.197.20.2
multilink bundle-name authenticated
stcapp ccm-group 2
stcapp
stcapp feature access-code
stcapp feature speed-dial
stcapp supplementary-services
port 0/1/0
fallback-dn 5428025
port 0/1/1
fallback-dn 5428008
port 0/1/2
fallback-dn 5421462
port 0/1/3
fallback-dn 5421463
isdn switch-type primary-net5
crypto pki token default removal timeout 0
voice-card 0
dsp services dspfarm
voice call send-alert
voice call disc-pi-off
voice call convert-discpi-to-prog
voice rtp send-recv
voice service voip
ip address trusted list
ipv4 10.198.0.0 255.255.255.0
ipv4 152.63.1.0 255.255.255.0
address-hiding
allow-connections sip to sip
no supplementary-service h225-notify cid-update
no supplementary-service sip moved-temporarily
no supplementary-service sip refer
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
fax-relay ans-disable
sip
rel1xx supported "track"
privacy pstn
no update-callerid
early-offer forced
call-route p-called-party-id
voice class uri 100 sip
host 41.206.187.71
voice class codec 10
codec preference 1 g711alaw
codec preference 2 g711ulaw
codec preference 3 ilbc
codec preference 4 g729r8
codec preference 5 g729br8
voice class codec 20
codec preference 1 g729br8
codec preference 2 g729r8
voice moh-group 1
moh flash:moh/Panjo.alaw.wav
description MOH G711 alaw
multicast moh 239.1.1.2 port 16384 route 10.198.2.9
voice translation-rule 1
rule 1 /^012237280\(..\)/ /54280\1/
rule 2 /^012236514\(..\)/ /54214\1/
rule 3 /^01223651081/ /5428010/
rule 4 /^01223506701/ /5428010/
voice translation-rule 2
rule 1 /^00\(.+\)/ /+\1/
rule 2 /^0\(.+\)/ /+44\1/
rule 3 /^\([0-9].+\)/ /+\1/
voice translation-rule 3
rule 1 /^9\(.+\)/ /\1/
rule 2 /^\+44\(.+\)/ /0\1/
rule 3 /^\+\(.+\)/ /00\1/
voice translation-rule 4
rule 1 /^54280\(..\)/ /12237280\1/
rule 2 /^54214\(..\)/ /12236514\1/
rule 3 /^\+44\(.+\)/ /\1/
rule 4 /^.54280\(..\)/ /12237280\1/
rule 5 /^.54214\(..\)/ /12236514\1/
voice translation-rule 9
rule 1 /^\(....\)/ /542\1/
voice translation-rule 10
voice translation-rule 11
rule 1 /^\+44122372\(....\)/ /542\1/
rule 2 /^\+44122365\(....\)/ /542\1/
voice translation-rule 12
voice translation-rule 13
rule 1 /^\([18]...\)/ /542\1/
voice translation-rule 14
voice translation-profile MPLS-incoming
translate calling 10
translate called 9
voice translation-profile MPLS-outgoing
translate calling 11
translate called 12
voice translation-profile PSTN-incoming
translate calling 2
translate called 1
voice translation-profile PSTN-outgoing
translate calling 4
translate called 3
voice translation-profile SRST-incoming
translate calling 14
translate called 13
license udi pid CISCO2921/K9 sn FGL145110RE
hw-module ism 0
hw-module pvdm 0/0
username administrator privilege 15 secret 5 $1$syu5$DsxdOgfS7Wltx78o4PV.60
redundancy
controller E1 0/0/0
ip tcp path-mtu-discovery
ip scp server enable
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
description internal LAN
ip address 10.198.2.9 255.255.255.0
duplex auto
speed auto
interface ISM0/0
ip unnumbered GigabitEthernet0/0
service-module ip address 10.198.2.8 255.255.255.0
!Application: CUE Running on ISM
service-module ip default-gateway 10.198.2.9
interface GigabitEthernet0/1
description to TATA NGN
ip address 115.114.225.122 255.255.255.252
duplex auto
speed auto
interface GigabitEthernet0/2
description SIP Trunks external
ip address 79.121.254.83 255.255.255.248
ip access-group SIP-InBound in
ip traffic-export apply cuecapture size 8000000
duplex auto
speed auto
interface ISM0/1
description Internal switch interface connected to Internal Service Module
no ip address
shutdown
interface Vlan1
no ip address
ip forward-protocol nd
no ip http server
no ip http secure-server
ip route 0.0.0.0 0.0.0.0 10.198.2.1
ip route 10.198.2.8 255.255.255.255 ISM0/0
ip route 41.206.187.0 255.255.255.0 115.114.225.121
ip route 77.37.25.46 255.255.255.255 79.121.254.81
ip route 83.245.6.81 255.255.255.255 79.121.254.81
ip route 83.245.6.82 255.255.255.255 79.121.254.81
ip route 95.223.1.107 255.255.255.255 79.121.254.81
ip route 192.54.47.0 255.255.255.0 79.121.254.81
ip access-list extended SIP-InBound
permit ip host 77.37.25.46 any
permit ip host 83.245.6.81 any
permit ip host 83.245.6.82 any
permit ip 192.54.47.0 0.0.0.255 any
permit icmp any any
permit ip host 95.223.1.107 any
deny ip any any log
control-plane
voice-port 0/1/0
compand-type a-law
timeouts initial 60
timeouts interdigit 60
timeouts ringing infinity
caller-id enable
voice-port 0/1/1
compand-type a-law
timeouts initial 60
timeouts interdigit 60
timeouts ringing infinity
caller-id enable
voice-port 0/1/2
compand-type a-law
timeouts initial 60
timeouts interdigit 60
timeouts ringing infinity
caller-id enable
voice-port 0/1/3
compand-type a-law
timeouts initial 60
timeouts interdigit 60
timeouts ringing infinity
caller-id enable
no ccm-manager fax protocol cisco
ccm-manager music-on-hold bind GigabitEthernet0/0
ccm-manager config server 152.63.1.19 152.63.1.100 172.27.210.5
ccm-manager sccp local GigabitEthernet0/0
ccm-manager sccp
mgcp profile default
sccp local GigabitEthernet0/0
sccp ccm 10.198.2.9 identifier 3 priority 3 version 7.0
sccp ccm 152.63.1.19 identifier 4 version 7.0
sccp ccm 152.63.1.100 identifier 5 version 7.0
sccp ccm 172.27.210.5 identifier 6 version 7.0
sccp
sccp ccm group 2
bind interface GigabitEthernet0/0
associate ccm 4 priority 1
associate ccm 5 priority 2
associate ccm 6 priority 3
associate ccm 3 priority 4
associate profile 1002 register CFB_UK_CAM_02
associate profile 1001 register XCODE_UK_CAM_02
associate profile 1000 register MTP_UK_CAM_02
dspfarm profile 1001 transcode
codec ilbc
codec g722-64
codec g729br8
codec g729r8
codec gsmamr-nb
codec pass-through
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
maximum sessions 18
associate application SCCP
dspfarm profile 1002 conference
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 2
associate application SCCP
dspfarm profile 1000 mtp
codec g711alaw
maximum sessions software 200
associate application SCCP
dial-peer cor custom
name SRSTMode
dial-peer cor list SRST
member SRSTMode
dial-peer voice 100 voip
description *** Inbound CUCM ***
translation-profile incoming PSTN-incoming
incoming called-number .
voice-class codec 10
voice-class sip call-route p-called-party-id
dtmf-relay rtp-nte
no vad
dial-peer voice 500 voip
description *** Inbound TATA MPLS ***
translation-profile incoming MPLS-incoming
session protocol sipv2
session target sip-server
incoming called-number ....
incoming uri from 100
voice-class codec 20
dtmf-relay rtp-nte
no vad
dial-peer voice 510 voip
description *** Outbound TATA MPLS ***
translation-profile outgoing MPLS-outgoing
destination-pattern 54[013-9]....
session protocol sipv2
session target ipv4:41.206.187.71
session transport udp
voice-class codec 20
dtmf-relay rtp-nte
no vad
dial-peer voice 520 voip
description *** Outbound TATA MPLS ***
translation-profile outgoing MPLS-outgoing
destination-pattern 5[0-35-9].....
session protocol sipv2
session target ipv4:41.206.187.71
session transport udp
voice-class codec 20
dtmf-relay rtp-nte
no vad
dial-peer voice 200 voip
description *** Inbound M12 *** 01223651081, 01223651440 - 01223651489
translation-profile incoming PSTN-incoming
session protocol sipv2
session target sip-server
session transport udp
incoming called-number 0122365....
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 201 voip
description *** Inbound M12 *** 012237280XX
translation-profile incoming PSTN-incoming
session protocol sipv2
session target sip-server
session transport udp
incoming called-number 012237280..
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 202 voip
description *** Inbound M12 *** 01223506701
translation-profile incoming PSTN-incoming
session protocol sipv2
session target sip-server
session transport udp
incoming called-number 01223506701
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 210 voip
description *** Outbound M12 ***
translation-profile outgoing PSTN-outgoing
destination-pattern +...T
session protocol sipv2
session target ipv4:83.245.6.81
session transport udp
dtmf-relay rtp-nte
codec g711alaw
no vad
dial-peer voice 211 voip
description *** Outbound ISDN for SRST and emergency ***
translation-profile outgoing PSTN-outgoing
destination-pattern 9.T
session protocol sipv2
session target ipv4:83.245.6.81
session transport udp
dtmf-relay rtp-nte
codec g711alaw
no vad
dial-peer voice 212 voip
description *** Outbound ISDN for emergency ***
translation-profile outgoing PSTN-outgoing
destination-pattern 11[02]
session protocol sipv2
session target ipv4:83.245.6.81
session transport udp
dtmf-relay rtp-nte
codec g711alaw
no vad
dial-peer voice 2000 voip
description *** Outbound to CUCM Primary ***
preference 1
destination-pattern 542....
session protocol sipv2
session target ipv4:152.63.1.19
voice-class codec 10
voice-class sip call-route p-called-party-id
dtmf-relay rtp-nte
no vad
dial-peer voice 2001 voip
description *** Outbound to CUCM Secondary ***
preference 2
destination-pattern 542....
session protocol sipv2
session target ipv4:152.63.1.100
voice-class codec 10
voice-class sip call-route p-called-party-id
dtmf-relay rtp-nte
no vad
dial-peer voice 2002 voip
description *** Outbound to CUCM Teritiary ***
preference 3
destination-pattern 542....
session protocol sipv2
session target ipv4:172.27.210.5
voice-class codec 10
voice-class sip call-route p-called-party-id
dtmf-relay rtp-nte
no vad
dial-peer voice 999010 pots
service stcapp
port 0/1/0
dial-peer voice 999011 pots
service stcapp
port 0/1/1
dial-peer voice 999012 pots
service stcapp
port 0/1/2
dial-peer voice 999013 pots
service stcapp
port 0/1/3
sip-ua
no remote-party-id
gatekeeper
shutdown
call-manager-fallback
secondary-dialtone 9
max-conferences 4 gain -6
transfer-system full-consult
ip source-address 10.198.2.9 port 2000
max-ephones 110
max-dn 400 dual-line no-reg
translation-profile incoming SRST-incoming
moh flash:/moh/Panjo.ulaw.wav
multicast moh 239.1.1.1 port 16384 route 10.198.2.9
time-zone 22
time-format 24
date-format dd-mm-yy
line con 0
login local
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line 131
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
session-timeout 60
exec-timeout 60 0
privilege level 15
login local
transport input all
line vty 5 15
session-timeout 60
exec-timeout 60 0
privilege level 15
login local
transport input all
scheduler allocate 20000 1000
ntp server 10.1.30.1
end
eucamvgw01#
Sh SCCP
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2014.03.03 17:57:44 =~=~=~=~=~=~=~=~=~=~=~=
SCCP Admin State: UP
Gateway Local Interface: GigabitEthernet0/0
IPv4 Address: 10.198.2.9
Port Number: 2000
IP Precedence: 5
User Masked Codec list: None
Call Manager: 10.198.2.9, Port Number: 2000
Priority: 3, Version: 7.0, Identifier: 3
Call Manager: 152.63.1.19, Port Number: 2000
Priority: N/A, Version: 7.0, Identifier: 4
Trustpoint: N/A
Call Manager: 152.63.1.100, Port Number: 2000
Priority: N/A, Version: 7.0, Identifier: 5
Trustpoint: N/A
Call Manager: 172.27.210.5, Port Number: 2000
Priority: N/A, Version: 7.0, Identifier: 6
Trustpoint: N/A
MTP Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Profile Identifier: 1000
Reported Max Streams: 400, Reported Max OOS Streams: 0
Supported Codec: g711alaw, Maximum Packetization Period: 30
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30
Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30
TLS : ENABLED
Transcoding Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Profile Identifier: 1001
Reported Max Streams: 36, Reported Max OOS Streams: 0
Supported Codec: ilbc, Maximum Packetization Period: 120
Supported Codec: g722r64, Maximum Packetization Period: 30
Supported Codec: g729br8, Maximum Packetization Period: 60
Supported Codec: g729r8, Maximum Packetization Period: 60
Supported Codec: gsmamr-nb, Maximum Packetization Period: 60
Supported Codec: pass-thru, Maximum Packetization Period: N/A
Supported Codec: g711ulaw, Maximum Packetization Period: 30
Supported Codec: g711alaw, Maximum Packetization Period: 30
Supported Codec: g729ar8, Maximum Packetization Period: 60
Supported Codec: g729abr8, Maximum Packetization Period: 60
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30
Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30
Conferencing Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Profile Identifier: 1002
Reported Max Streams: 16, Reported Max OOS Streams: 0
Supported Codec: g711ulaw, Maximum Packetization Period: 30
Supported Codec: g711alaw, Maximum Packetization Period: 30
Supported Codec: g729ar8, Maximum Packetization Period: 60
Supported Codec: g729abr8, Maximum Packetization Period: 60
Supported Codec: g729r8, Maximum Packetization Period: 60
Supported Codec: g729br8, Maximum Packetization Period: 60
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30
Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30
TLS : ENABLED
Alg_Phone Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Device Name: AN71FEF7F070080
Reported Max Streams: 1, Reported Max OOS Streams: 0
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: g711ulaw, Maximum Packetization Period: 20
Supported Codec: g711alaw, Maximum Packetization Period: 20
Supported Codec: g729r8, Maximum Packetization Period: 220Supported Codec: g729ar8, Maximum Packetization Period: 220
Supported Codec: g729br8, Maximum Packetization Period: 220
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: ilbc, Maximum Packetization Period: 120
Alg_Phone Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Device Name: AN71FEF7F070081
Reported Max Streams: 1, Reported Max OOS Streams: 0
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: g711ulaw, Maximum Packetization Period: 20
Supported Codec: g711alaw, Maximum Packetization Period: 20
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: g729ar8, Maximum Packetization Period: 220
Supported Codec: g729br8, Maximum Packetization Period: 220
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: ilbc, Maximum Packetization Period: 120
Alg_Phone Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Device Name: AN71FEF7F070082
Reported Max Streams: 1, Reported Max OOS Streams: 0
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: g711ulaw, Maximum Packetization Period: 20Supported Codec: g711alaw, Maximum Packetization Period: 20
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: g729ar8, Maximum Packetization Period: 220
Supported Codec: g729br8, Maximum Packetization Period: 220
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: ilbc, Maximum Packetization Period: 120
Alg_Phone Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Device Name: AN71FEF7F070083
Reported Max Streams: 1, Reported Max OOS Streams: 0
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: g711ulaw, Maximum Packetization Period: 20
Supported Codec: g711alaw, Maximum Packetization Period: 20
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: g729ar8, Maximum Packetization Period: 220
Supported Codec: g729br8, Maximum Packetization Period: 220
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: ilbc, Maximum Packetization Period: 120
eucamvgw01# -
Directory Caching issue with Cisco Jabber client for Windows
Hi ,
I am facing cache issue with Cisco Jabber client for Windows. If I do any change related to modification or deletion of contacts in Active Directory/ Callmanager, it does not reflect in the Jabber. Because jabber takes the contacts from the locally stored cache file in the Windows system.
Every time I have to remove the cache file to overcome this issue, practically it's not possible to do the same with all the Widows users. As, if any employee leaves the company and still I can see his contact appears in the "Cisco Jabber client". I have not seen this issue with Android/Apple iOS.
Is there any automated way to remove the cache file?
Here is the detail of CUCM,Presence and Jabber.
CUCM version: 9.1.x
Presence : 9.1.X
Jabber : 10.5 and 10.6Hello
On our environment we had to install a dedicated Microsoft Certificate Authority "just for Cisco Jabber usage" to house the
Network Device Enrollment Service.
Our certificate for the CUPS were generated on this Certification Authority too.
I discussed this certificate matter with my colleagues this afternoon and nobody seems to remember how these certificates were deployed into the
Enterprise Trust store for the users.
But I think they asked all 400 users to accept the 3 certificates by answering "yes" to the popup instead of using a script deployed by GPO...
I wish you success with that deployment and really hope you have a technical partner that *Knows* this subject.
Our partner left us alone with that unfortunately.
Florent
EDIT: If the "Certutil script method" works, please let me know. This could be useful in our own deployment. -
Cisco Prime Infrastructure 1.2 with Cisco Prime Network Control System Hardware Appliance
Hi Team,
I have following BOM
Cisco Prime Infrastructure
R-PI-1.2-K9
Cisco Prime Infrastructure 1.2
1
R-PI-1.1-500-K9
Prime Infrastructure 1.2 Software - 500 Device Base Lic
1
L-PILMS42-500
Prime Infrastructure LMS 4.2 - 500 Device Base Lic
1
L-PINCS12-500
Prime Infrastructure NCS 1.2 - 500 Device Base Lic
1
PRIME-NCS-APL-K9
Cisco Prime Network Control System Hardware Appliance
1
PI-APL-IMAGE-1.2
Cisco Prime Infrastructure 1.2 Appliance Software
1
Pls let me know if we have both NCS and LMS preinstalled with Cisco Prime Infrastructure 1.2 Appliance Software orwe need seperate appliance or server for LMS 4.2.
RegardsHi Scott,
Thanks for the response but I got to know that LMS and NCS are combined in single ISO image from PI 1.2 and can be installed on the same physical NCS appliance.
Can you pls check this.
Regards -
Cisco Prime LMS appliance Compatibilty with Cisco Prime NCS
Hi,
Is it possible if we can install Cisco Prime LMS 4.2 in the appliance which is inbuilt with Cisco Prime NCS .
We have PILMS42-1.5K-U license available with us.
Rgds,
KamalOne can install either LMS 4.2 or NCS on the a physical (software on PRIME-NCS-APL-K9 hardware) or virtual appliance (software installed on customer-provided VM).
The two products (NCS and LMS) cannot coexist on a given appliance instance. This is due to change in the future as LMS and NCS merge under the Cisco Prime Infrastructure 2.0 release but for now they are distinct and separate products with a common approach and similar look and feel but requiring separate servers, whether physical or virtual.
Please refer to the ordering and licensing guide here. -
Controller software compatibility with cisco prime 2.0
Are any of the following wireless software (5500 controller) releases compatibile with cisco prime 2.0 ?
- 7.4.121.0
- 7.6.100.0
M.HI,
Cisco PI 2.0 supports:
Cisco 5500 Series
7.0 through 7.4.110.0
http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/2.0/release/notes/cpi_rn.html
Your both software not supported by PI 2.0.
May be PI 2.1 will support both these software in future.
Regards -
Is there any known issues with Cisco Meraki APs with client devices which publish PMF support in probe requests ? We are seeing connectivity issues with Cisco Meraki MR12,MR16 and MX80 models . Please update if there are any known issue with these APs.
Thanks for your thoughts, Nathan. We do actually have the "Enable Fast Reconnect" option selected on our wireless profile. Good idea, though.
We did also (originally) have 2 RADIUS servers defined within our wireless network. What we discovered was that each Meraki AP will try each one in order, top-to-bottom, and then primarily use the server that responded to it first. So, if for any reason you have a short-lived issue with your local RADIUS server responding to requests, and the AP is able to talk to a remote RADIUS server (in our case, one on the other side of the world) instead, the AP will elect to use the remote RADIUS server instead. In our case, the latency is high enough between these APs and this remote RADIUS server that while a client is roaming between APs, and having to re-authenticate, the entire process breaks down because (1) the client is moving between APs faster than the remote RADIUS server can authenticate the client, and (2) the entire exchange and communication ends up timing out -- thus forcing a manual re-connect. This is not a common occurrence by any means, but I just wanted to share what made us later choose to define only 1 RADIUS server, in the network settings. Surely our circumstance here is rather unique, but I thought it might be worth mentioning. Having only 1 RADIUS server defined forces ALL of our APs to use the same RADIUS server, regardless of anything else. It has resulted in a much smoother re-auth process for our clients.
I appreciate the link you sent, however. If I come across anything else that is helpful, I'll certainly post it back here. I appreciate your input once again! -
Job Scheduler Timer issue in Cisco Prime Infrastructure 1.2 ?
Has anyone run into this issue where the job scheduler in CPI 1.2 report that the job that is being scheduled is before the current time even though it isn't ?
This only started happening after our time change yesterday. The system is setup for the correct time (NTP) this is confirmed in the app and also on the CLI console access (show clock)
Anyway we get this error message (attachment) in the lower right corner of the attachement.
It's not allowing the jobs to be scheduled. Rebooted the system yesterday and thought that it fixed it, but evidently I tried another scheduled job today and it's got the same issue.
TAC Case is already opened on this but I thought I'd ask here as well.
Regards,
Tom W.I'm answering my own question: upgrade to 1.3 from 1.2 and the problem is resolved. Rebooting the VM on 1.2 did help for 1 day but then the problem came back, so my advice is simply to upgrade to 1.3 which I would have done initially if I had known that 1.3 was available. Hope this helps. The problem itself in 1.2 is unclear what is causing it because NTP and the APP and the underlying time in the console (cli) are all good; so somewhere in the scheduler it may have gone off track after the daylight savings time shift this past week. Bottom line: 1.3 upgrade and keep hope alive, bro.
-
Issues with running permission scripts on Hoted desktop via Citrix and when deploying via SCCM
I am running a permissioning VBScript which runs when I do a standalone insallation manually running the power shell commands to add and publish the application.
This only runs vis SCCM when a machine installation is acrried out but not a per user installation. Any ideas?
The same script seems to run sometimes & sometimes does not on a hosted desktop with aps publish via citrix from the appv server. Any ideas?. A coppy of my Deploymentconfig.xml file userscript section that calls the script is below
<UserScripts>
<StartProcess RunInVirtualEnvironment="true">
<ApplicationId>[{AppVPackageRoot}]\Adobe Photoshop CS6 (64 Bit)\Photoshop.exe</ApplicationId>
<Path>[{AppVPackageRoot}]\..\Scripts\AdobeSerialization.exe</Path>
<Arguments>adobe_prtk --tool=VolumeSerialize --provfile=[{AppVPackageRoot}]\..\Scripts\prov.xml</Arguments>
<Wait RollbackOnError="false" />
</StartProcess>
<StartVirtualEnvironment>
<Path>WSCRIPT.EXE</Path>
<Arguments>[{AppVPackageRoot}]\..\Scripts\VFSCACLS.vbs -guid 6d0756af-b755-493b-8cee-4299e8666978 -error -name "Adobe Photoshop CS6"</Arguments>
<Wait RollbackOnError="false" />
</StartVirtualEnvironment>
</UserScripts>
The guys in the build team reckon this is an application issues but I can't see how it can be if the applications runs when manually calling the powersehell commands. Also like I said on the Hosted desktop one minutes the script runs and one minute it does
not.
Can someone help please?Hello,
If deploying the application to the user, and the configuration file is updated as part of the content and distributed to the DPs, and then downloaded to the client and the client is enabled to run scripts - no I never had that issue.
If I had something which didn't work I would usually verify what is on the Distribution Point?
You can download the SCCM 2012 R2 toolkit to verify what is on the DPs;
http://www.microsoft.com/en-us/download/details.aspx?id=36213
If it is deployed to the client - it means you can read the client log-file from SCCM. See the AppEnforce.log as a potential candidate;
http://technet.microsoft.com/en-us/library/hh427342.aspx#BKMK_AppManageLog
If it gets properly parsed by the App-V Client you can check the App-V event logs, see Tim Mangans blog post about enabling further debug-logs;
http://www.tmurgent.com/TMBlog/?p=1247
As I can't see what is happening within your Environment I would redo all the steps and verify what the results were of each step. If one step fails, I would then post what step I had performed up until that point, what the result were of each step and what
was happening within the final step that I would consider a failure.
Nicke Källén | The Knack| Twitter:
@Znackattack -
I seem to be having a lot of connectivity issues my iPad. It takes a long time to load and sometimes will not load a page at all. I seem to be having issues with streaming in that it will play a song and just stop. It seems I have to turn it completely off and restart.
Anyone had these issues?Settings > General > Reset > Reset network settings
Maybe you are looking for
-
How do I use the analog input (ADC) to drive a motion profile in MAX
We are trying to use an anolog input signal from a DAQ card to control the motion contol axis. For now, we want the motor speed to follow a sinusoidal voltage waveform, and later on, we will be using a more complex velocity profile. In order to acc
-
HP Photosmart Premium C309g-m (Fails or SLOW to Print Wirelessly)
My printer has usually worked until recently (past couple months). I have re-installed the driver several times, uninstalled the HP software, re-installed the driver only... and still the same symptoms occur. OS: Windows 7 WiFi Router: Linksys E4200
-
may i know how to do the save as function example to save, once i click the save as, it would allow me to save the current file to another filename? thanks!
-
How to edit a post in Apple Support Comunities?
If I just posted something and saw it had typos. Is there any way to edit the post or remove it? I have searched all over for an option to edit my post and see none. I saw someone say that it was possible to edit within 15 minutes of making the p
-
How do I get photos off of my iphone and onto my computer? I've synced several times and it didnt work. I dont want to email the photos because I have like 25. Thanks for any help.