Issue with mobile network signal ("Searching")

I recently purchased 2 iPad from Singapore and upon retuning to Malaysia, i applied for 2 mobile broadband package from the same mobile provider.
Issue i am facing is, on one of the ipad, the mobile network signal bar displays "Searching" almost all the time; only a few times it displays strong signal with 3G icon then it drops to "Searching" again. I tried to swap the micro sim around between both ipad but no such issue on the 2nd ipad which is consistenly strong signal.
I even restored the ipad (factory shipped 3.2.2) but no success.
What should i do?

After further test, I noticed the unit can't find any mobile provider under Settings > Carrier when signal bar displays "Searching".
Enabling airplane mode does not help either; only workaround is to disable Cellular Data under Settings > Cellular Data then Enable it again.

Similar Messages

  • Issue with mobile network vs wifi

    Hi all, after using wifi the iPad cannot connect to 3g. It says that server is not responding or that it cannot activate mobile networks (while the signal strength is full). So I need to restart ipad and then it's ok. Thanks in advance

    Same problem here...more specifically out of nowhere my ipad 3 seems to be unable to activate cellular network.  But the "wheel of death" will spin and spin for many minutes prior to alerting me of the connection issue.
    My ipad 1 was problem-free and the 3 just seems so much slower, especially when connected to 3g/4g.

  • Anyone else had issues with phone network being unavailable on iPhone 4 since updating to iOS 5.0.1? My iPhone 4 is continually searching for a network and does not find my provider. I swapped SIMs with another iPhone 4 on ios 4 to confirm device problem.

    Has anyone else had issues with phone network being unavailable on iPhone 4 since updating to iOS 5.0.1? My iPhone 4 is continually searching for a network and does not find AT&T, my provider. I swapped SIM cards with another iPhone 4 running ios 4 and established this is a device problem, not a SIM card problem.

    Does the device get any signal? 
    Sounds like the device may have had a hardware failure.  If it is out of warranty, the only option is the Out of Warranty replacement.
    AppleCare is only an option if it is still under the original warranty.

  • No connection with mobile network

    My phone (which was bought only 2 days ago) has suddenly lost connection with mobile network. "Emergency calls only" is written on lock screen, near signal power bar there is a small red 'x'. I tried turning it off and on, tacking sim card out and putting it back in, trying to connect to mobile network manually through the settings "Service providers" (it says "Could not connect to network now. Please try again later." when I try to connect manually), changing network mode (to all possible modes). Still no luck. I can't send an sms or make a call.
    What should I do?

    I got similar issue but the only thing is phones randomly disconnects itself from the mobile network in some days. Then no matter you manually search for the network and try registering, it simply wont connect to any network.Your only solution is to reset the phone or turn off and on and it again auto catches your operator.

  • Image Ultra Builder 3.x issue with T61 Network Driver load

    Hello,
    I am having issues with a Network deployment of an image on a T61 (7659-12U) During the intial boot up phase with the Network Boot disk that was created from IUB, I receive and error 1231 - The Network Location cannot be reached..  I am currently using IUB for deployment of A31, T40/42 as well as the T60 model line. None of these loads are having the problem.
    Any help on this would be very much appreciated.
    Thank-you in advance.
    Ed

    Hi,
    IUB 4.01 is using WINPE 2.0<Vista based> and IUB 3.1 was using WINPE 1.0/1.1<XP Based>.
    This has nothing to do with the actual image deployment. It's just that the WINPE looks more like
    Vista. And this is why the method changed after you updated from 3.0/3.1 to 4.00/4.01.
    To answer your questions from before:
    1) Does updating IUB to version 4.01 still allow me to deploy Windows XP ?
    Yes, it's still supported and possible.
    2) Where on the boot CD should the new driver files be located. I took this to be PREBOOT\DRIVERS ?
    As the new IUB is using WINPE 2.0, the best location for the NIC drivers is the file :
    tvtos\winpe.wim
    However, this is my advice.!
    For my Image deployment I'm no longer using the CD for network deployment. I'm using USB key which gives me more options for the image deployment and the automatization of the deployment process.
    However, if you want to use CD for network deployment, then you can do it in following way.
    !!!NOTE: this is not the offical way, nor the supported way, but trust me, that it's working like charm !!!
    - go to your repository location %repositorylocation%\modules
    - find the file called "Z633003A.TVT" and open it using your fav zip application
    - after you open this file, go to following location: tvtos\
    - extract the "winpe.wim" and using WAIK unmount this file and add the NIC drivers into this .wim file
    - after all the drivers are in the winpe.wim file, just copy it back to the "Z633003A.TVT" file and create a new Deployment CD
    How to add NIC driver using WAIK:
    This is prety easy step, but for more info, check following link:
    http://www.svrops.com/svrops/articles/winvistape2.htm
    As I described earlier, I'm using USB key for Network image deployment, so I have not done it this way, but I have done it a bit simplier.
    Here are my steps:
    - created a Distribution USB key <suing the same method, that you are using when you create a Network deployment CD, but instead of a CD I select my USB key>
    - once the USB key was created successfully I unmount the "tvtos\winpe.wim" file and add all the NIC dirvers into it
    This is all that I have done.
    Yes, of course there are couple other steps, that I do, like modifying the BCD file, adding other WINPE files, diagnostics and other deployment tools, however, this is not realy a part of IUB, I'm using it for my WDS server and other deployment tools, that I need to use. If you know, what I mean, then you surely understand, that it's a live safer to have everything on one USB key, then on multiple CD where I need to search throught all of then to find the correct CD.
    Let me know, whether this method is more suitable for you.
    As described above, this is not the realy official/supported way, but it's working for sure.
    Rgrds 

  • GPS Inaccuracy With Mobile Network Enabled

    I have a BB AT&T Passport.  The GPS location with Mobile Network enabled is .25 - .5 mi off.  If I disable Mobile Network and just use WiFi then my GPS Location is within 50 - 100 ft.  Why is there such a disparity location with AT&T LTE?  I have the latest software update from AT&T.  Can we get this problem fixed AT&T?

    Hi there! @loosefoot
    Thanks for posting your concerns. I’m sorry to hear the location information is off.
    So we can further assist you, please private message me by clicking here and provide the city, state and zip codes where you are experiencing this issue.  
    Thanks!
    Charise

  • Is there problems with the network/signal in TA3 Taunton area

    Is there problems with the network/signal in the TA3 Taunton area I have not had a signal all day and then to make contact with one of my children regarding school pick up.

    Unfortunately so. Spoke to EE today and the service may take up to 72 hours to get back to normal - which is unbelievable given how much we use our phones for day to day life! As they cannot do anything for us, to thank us for our patience they are asking us to monitor when the service resumes and get back to them (no doubt on their £ per min line) and let them know and they’ll credit us for the down time. Just Brilliant!!     

  • My iPad 2 has stopped picking up mobile network signals once it moves out of a WIFI zone. Please advise

    My IPad2 has stopped picking up mobile network signals once it moves out of a WIFI Zone.  any possible reason?

    Unbelievable.
    After taking all the time to write and post that, I then switched "airplane mode" on and off again and it started picking up the 3G signal fine.
    I had read a couple of threads about Ipads / Iphones "locking" onto GPRS and this being the only way to switch them back, but I DEFINITELY tried this before the IOS 7 upgrade and it didn't help.
    So was it just a coincidence this time or did the upgrade make a difference? No way of telling I suppose so no help if you're reading this looking for a solution. I can only keep an eye on it and see if this becomes a regular problem......

  • Do iphone 5 s have any issues with overheating or signal drop out

    do iphone 5 s have any issues with overheating or signal drop out

    I had this issue with my iphone.. the phone got so hot it actually burned my leg. Took it back to apple and they switched it with a new phone! Had no issues since

  • Complaint: Issue with the Network

    Facing issue with the Network for most of the time and sometimes even Data for both 3G and 2G.
    My service provider was BSNL, Hyderabad, AP, India-50016
    I have check even with my service provider from there they don't have any issue..
    But the same works with my old BB8520 and others.
    Please can you help me?
    BBZ3-STJ100-1 OS V10.2.1.3247

    Is it h+ or H+?
    I've had similar issues when my sim card was bad. I had cut it down to micro sim size and it worked fine for a month. Then it stopped working in the Z10 but worked in my 9810. Try having your carrier replace your sim card.
    1. Please thank those who help you by clicking the "Like" button at the bottom of the post that helped you.
    2. If your issue has been solved, please resolve it by marking the post "Solution?" which solved it for you!

  • My iPhone cant reach any mobile network signals what do i do

    my iPhone cant reach any mobile network signals what do i do

    Have you talked to your cell provider? 

  • Z30 - Mobile Network signal issue

    Hi!
    i am using Z30 for last about 2 months.
    facing problem in dropping and varying mobile signal strength,
    while other devices incl. older BB devices are showing steady signal strength at same place same time.
    also facing call quality deterioration while calling
    please....help!!!

    deebee11 wrote:
    sorry....omitted to mention..
    online through flipkart...pvt online shopping...
    OK, and if you will, please look at the Settings > Network and Connections > Mobile Network.
    Tap the Network Technology. What do you have set there, and what are the other choices?
    1. If any post helps you please click the below the post(s) that helped you.
    2. Please resolve your thread by marking the post "Solution?" which solved it for you!
    3. Install free BlackBerry Protect today for backups of contacts and data.
    4. Guide to Unlocking your BlackBerry & Unlock Codes
    Join our BBM Channels (Beta)
    BlackBerry Support Forums Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • Issues with Mobile Broadband on the Tablet 2

    Is anyone having slowing degrading connection issues with Vodafone and the Tablet 2. Upon fresh boot, signal is strong, then degrades until a reboot is required. Seems very odd. Other devices connecting to vodafone at the same location have no problems.

    hi rogerf.
    due to it was working before, i can say there's no compatible issue with the device and computer.
    you may need to contact ericsson or the mobile provider in aussie. still, there may be users here who has/had the same issue. you can wait for reply.

  • Fix for WebHelp output issues with IE 11 breaks Search function

    I use RoboHelp HTML 9 and have been having issues with generated WebHelp in IE 11. The TOC was totally blank and the Search tab looked fine but did not function. Everything worked fine in Firefox. After much experimenting and online research in these forums and elsewhere, I have been able to get the TOC to display properly in IE 11 (and Firefox) but the fix has caused the Search tab to stop functioning as per this other forum post RH9 Webhelp Search function is not working properly.
    I need to have BOTH TOC and Search displayed and functioning properly but in order to get the TOC displayed properly I had to change the Preferred Format setting to "Pure HTML" and, according to the post mentioned above, that is what messes up the Search function. Is there a solution that will allow both TOC and Search to function properly?
    Here is a summary of the steps I have taken to get to this point:
    Tested WebHelp output from two different projects of my own as well as the Salesbuilder starter project - all would display/function properly in Firefox but not in IE 11 (blank TOC and non-functioning Search).
    Found a "patch" for RH10 for the exact problem I was having with RH9 but was not able to find a version for RH9. Since the patch included 2 files (whutils.js and whver.js) only, I backed up these files in the RoboHTML\WebHelp5Ext\template_stock directory and replaced them with the new ones.
    Regenerated one of my RoboHelp projects - still didn't work in IE 11 and now didn't work in Firefox either!
    Tried turning on Mark of the Web but this did not help and would not allow opening PDF's which is necessary to one of the projects so I turned it off again.
    Changed Preferred Format setting to "Pure HTML" instead of "DHTML" and the TOC displayed and functioned properly in IE 11 and Firefox! Hurray!!
    Celebrated for 10 seconds until I clicked on Search tab and saw the input box filled with letters of the alphabet with other random letters, words, numbers below. It looks almost like an index but neither of my projects uses an index and I have not generated one in either project.
    Found the post mentioned above which states that the solution is to change the Preferred Format setting back to DHTML but when I do that I am back to blank TOC and proper-looking but non-functioning Search!!!
    I have now removed the Search tab from the output of one of the projects since it is not really necessary but I need to find a fix for this for my other project.
    Both of my projects are run locally - one is release documentation that is distributed on a CD and the other is CSH which is loaded on the local server with the software for which it was created.
    Dorothy
    Note to Administrators: Sorry, but I originally posted this as a reply to a previous post - Contents, Index, & Search do not display in generated help... - so perhaps it should be removed from that thread to avoid confusion.

    The "preliminary" fix provided has worked perfectly! All versions of my WebHelp project now display TOC properly and I was able to change the Preferred Format setting back to DHTML so the Search tab both displays and functions as it should. I am very grateful to William for providing this fix which works in both IE 11 and Firefox. Someday I will pursue the fixes to make it work in Chrome as well.

  • Recurring issue with mobile upload

    Hi all,
    Using Lightroom 5.6, I am experiencing ongoing issues with synchronising  (uploading) LR to mobile devices. In brief, the upload will typically fail in mid-session with some collections partially or fully uploaded and some not started. (This may initially have been caused by going off-line during an upload),  It will not recover. Deleting all uploaded data to prompt a restart does not help - it does not restart either.
    Previously I have had to contact support and send the diagnostic report. Apparently there is a flag on the server end that needs resetting. Not the most satisfactory of solutions as it requires an action outwith the users control, but it does / did reset the file transfer interface. Apparently this bug was scheduled for fixing in the next up date. I understand I am on the latest (5.6) version , so does anyone know if this is still a bug?
    Meantime, can support please reset my connection?
    Regards .... Alastair

    Hi Alastair,
    I've contacted you privately.
    Thanks,
    Ignacio

Maybe you are looking for