Issue with the Battery on my N9, after 1.2 update.
Right, since the 1.2 battery I'll be lucky to be at 20% after eight hours at work.
I've got facebook and twitter notifications enabled.
No RSS feeds.
Calendar syncing. (hourly)
No email.
3G is always on, alternatively wi-fi.
I text most of the day, maybe 4-5 messages an hour max while I'm at work.
I don't do any browsing while at work, don't use the GPS.. it just sits there and I text.
Before the 1.2 update, with this usage profile, I was able to get 2 days of battery out of this.
I tried removing all apps, didn't make a bit of difference.
I reset the device settings, no change.
Looking at battery usage monitor, my device appears to idle at 161mA, which is only 6 mA lower than my avg current consumption.
As I'm writing this, the phone has discharged from 80 to 73% in 34 minutes, which seems like a lot. It's been idle for 72% of those 34 minutes.
Looking at the "top energy consumers" page, Device idle is currently responsible for 65% of the battery drain, whilst MeeGo System is at 19%. Everything else is at 5% or lower. All I want is to be able to get a days use out of this phone. As it stands, I'm not even able to take it out and go nuts with the camera, for fear of losing all the battery and rendering it useless.
Prior to the update I was able to nab photos, GPS a bit and write plenty of texts, and while it'd require a charge by the time I had to go to bed - it would handle it fine. Anyone else experiencing this? Any tips? Anything I can do?
Solved!
Go to Solution.
My N9 battery is completely drained in just 6 hours. Today the Average Idle Consumption shows that it was 64mAh. I don't know what cause the problem. I'm just sending a text message. No WiFi activity. But when connected to the WiFi, the battery won't last up to 5 hours. Sometime it reach up to 80-90mAh when connected to the WiFi. I'm running on a GSM connection. I don't use the 3G.
This happens since the PR1.1 but it getting worst and worst since PR1.2.
Nokia 3310, 8250, 6070, 6060, 3120, 1110, 1280, 5300 XpressMusic, N76, 6120 classic, 5800 XpressMusic, 5530 XpressMusic, N900, C3-00, N8-00, N9, 700, X2-01, Asha 302, Lumia 610, Lumia 920, Asha 501, Lumia 820 and Lumia 1520...
Similar Messages
-
Issue with the material field in ME23N after upgrade
Hi Experts,
We are having an issue with transaction ME23N in ECC6.0 after upgrade from 4.6c.
In this transaction for the given PO the value of the material is not populating. The material coloumn is displaying but the value of the material is not coming.
For the same PO with the same data we are able to see the material number in ME23N in 4.6c.
Please help me to resolve this.
Thanks,
RakeshHi,
If you are a functional consultant then check the configuration settings in SPRO and compare it with the one in 4.6c system to find if the material number display in ME23N is enabled in your new system or not. Go to tcode SPRO and Material Management-> Purchasing->Purchase Order->Define Screen Layout at Document level.
Execute this and select on ME21N or tcode that you are having problem with. Then press details button and double click on Enjoy fields. Check if it Display check box is ticked or not.
KR Jaideep, -
This software is killing the battery life. Anyone find a way to solved this issue with their iPads? If not, is there a way to go back to the last software, this is not acceptable.
I have no issue since upgrade to IOS 7 no loss of battery life and you cant downgrade,apple dont support it
-
I need help on this matter, this is the only thing that is keeping me from installing iOS 6. Also, how can I save my data, apps and other stuff that I already installed on iOS5? Also, if I create another apple ID, will my data, apps etc be lost, do I have to download the stuff again? Help me out!!
Device not recognized in iTunes for Windows
Device not recognized in iTunes for OSX
Until the issue with iTunes recognizing the device is resolved, there is no way to update it. -
HT1483 has anyone had issues with the battery charging then dying with in 15 minutes thanks
Hello friends wondering if anyone has charging issues where the ipod 4 charges and seems to die after 15 minutes. thanks
Well i feel in this case you need to upgrade the firmware of your router. You can Download frjmware.
Open an Internet Explorer browser page on a computer hard wired to the router...
In the address bar type - 192.168.1.1...Leave the username blank & in password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Now reset your router :
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
Also make sure that your computer is set to obtain IP automatically, disable any firewalls, security softwares on the computer before trying to access the setup page... -
Has anyone had issues with their HP Lightscribe CD/DVD after a sofware update?
After recently installing software updates from HP and Microsoft my laptop no longer shows the drive with the CD/DVD under Computer. I can install a dvd and hit the Quick Play and it plays fine but it's also a lightscribe dvd burner and I can't send videos or photos to the drive because it's not showing up under the listed drives. Neither are my removable disk flash ports showing up. They were there before the most recent HP and Microsoft security updates installed. When I go to Device Management it shows up there but also shows an error message under the Devices Status: "This device cannot start. (Code 10), Click 'Check for solutions' to send data about this device to Microsoft and to see if there is a solution available." When I click to check for solutions I get the message back that the device is installed and functioning properly. I also checked the device driver and it's telling me it's the correct and most updated driver. i'm at a loss as I'm not at the point where I'm able to replace this laptop which is used for personal and home business use. Does anyone have a solution other than doing a total recovery? I tried taking it back to just before the last update but they're still not showing up. It's like something wiped them out.
Yes with some docks and car systems but I do not remember the specific devices. Sometimes and iOS update breaks compatibility.
Try:
- Go to the dock manufacturers and see what they say. Also see if there is a firmware available for the dock
- Reset the dock
- Sometimes this works:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device. -
I have the sames problems with the battery of my itouch 4g when i update to ios 5.0.1
the battery of my ipod lows more fast when i update to ios 5.0.1 i need help
I had they same problem, but with my iPad. Howeve, I think that most of us have upgraded to 5.0.1 with the patch file, which made us all have a worse battery drainage. I WILL TELL YOU HOW TO FIX IT
RESTORE THE WHOLE 5.0.1 firmware TOGETHER the 700+ MB. You will notice the major battery improvement.
Remember to mark me with the correct answer... :) -
Recently I have noticed my mac's battery is running out quite fast. I have checked the activity monitor and quit any programs with a high CPU% but there still seems to be an issue.
In an hour my battery can go from 100%- 65% in an hour. I'm not watching movies, just browsing the net. I'm not downloading anything either.
Here is my battery info;
Battery Information:
Model Information:
Serial Number: 9G1130EWAD3NB
Manufacturer: DP
Device Name: bq20z451
Pack Lot Code: 0
PCB Lot Code: 0
Firmware Version: 201
Hardware Revision: 2
Cell Revision: 164
Charge Information:
Charge Remaining (mAh): 3156
Fully Charged: No
Charging: No
Full Charge Capacity (mAh): 4842
Health Information:
Cycle Count: 429
Condition: Normal
Battery Installed: Yes
Amperage (mA): -997
Voltage (mV): 11551BMB1989,
then when it was new, your battery had a capacity of around 5800 mA·h — so it’s currently at 83.5% of its original capacity. Apple considers a battery “consumed” when it reaches 80% of its original capacity, and their estimate is that this happens at around 1000 cycles. Since you have 429 cycles so far, that means that your battery has lost capacity well above Apple’s predicted rate. -
I was able to restore from itunes. I could see the application updating all of the apps. The phone 'clinks' - now what do I do? the only option on the phone is 'Back', which takes me to the update options of restore from iCloud or iTunes. Based on what I could see in itunes, I thought it was completed? Is there something else I am supposed to do...???
Hi there Paula120,
You may find the troubleshooting steps in the article below helpful.
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/ts1538
-Griff W. -
Would a flash storage issue affect the battery being charge?
I received a notice about my macbook air and defective flash storage. I brought my macbook into an apple store on Saturday to have the firmware updated. Since then my macbook has been unable to charge the battery with the adaptor plugged in. I am wondering if the flash storage has anything to do with this? I have not had an issue with the battery charging or not charging before this.
http://discussions.apple.com/thread.jspa?threadID=2474499&tstart=0
-
Is anyone having problems with the battery drains quickly and the iphone4 heats up in use and in charging after upgrading to 5.1.1?
I have had the same problem but I seem to be getting somewhere to fixing it!!! My battery was going down at 20% an an hour now its 10% with constant use and 5 in standby !!! So improvement all round
First I did a restore then I drained the battery i started to charge it and when it came on I turned the phone off completely and let it charge to 100% I then left it for a couple of hours on charge at 100. I saw no improvement after 1st drain so I repeated the drain battery and charge steps again with the phone turned off when charging and have seen a very big improvement. I am going to do it again tonight and hopefully problem solved!!!!
The next issue is iMessage as that's playing up and wifi drop out
Good luck -
I'm trying to connect to my home wifi with my imac gh5. After I enter the password it says connection timeout or password incorrect. I know there's no issue with the connection but I don't know what else to do. Does anyone know how to fix this problem?
What is the make & model of your home Wi-Fi router that you are attempting to connect your G5 iMac to? Which exact model of iMac do you have?
What wireless security type is your router using: WEP, WPA, or WPA2? If you temporarily disable wireless security, can the iMac connect to it now? -
It seems after the latest software update, my iphone 4 has issues with the phone and voicemail locking up as well as opening random apps. Any thoughts?
Hi clintfromid,
Thanks for using Apple Support Communities. I would recommend closing all your apps and restarting and maybe resetting as good initial troubleshooting steps for this:
iOS: Force an app to close
http://support.apple.com/kb/ht5137
iPhone, iPad, iPod touch: Turning off and on (restarting) and resetting
http://support.apple.com/kb/HT1430
Cheers,
- Ari -
CD-ROM drive letter changed to the next available letter after an issue with the Storage appliance.
Server platform:Windows server 2008 R2 Enterprise.
Last time we experienced an issue with the storage device we are using to attach a disk to our server 2008 (virtual). This storage device is also providing storage to the ESX where the server 2008 is hosted.
The drive configuration in the server was:
System C:\
Tools D:\
Apps E:\
CD-ROM F:\
Some hours after the storage appliance issue, we realized the Application on the server was not working and then we restarted the server. After restarting the server we went to the file explorer and realized that the Apps volume had the drive letter F and
the CD-ROM had the E letter assigned.
I assume windows lost the Apps disk due to the SAN disconnection. Maybe the CD-ROM was also disconnected and when the Storage appliance was connected again the CD-ROM acquire the next drive letter it found, which was the letter E:. Then the Apps disk was
also discovered by Windows and it assigned the next available letter, F:.
I was looking for some MS knowledge base to see how Windows 2008 server assigns the letter to the CD-ROM and how we can permanently fix the letter assigned to the disks and the CD-ROM so that this issue won't happen again. As you know many applications use
the path including the drive letter.
I thought that when you set a CD-ROM drive letter, it remains forever as is, and that in case of a SAN disconnection Windows assigns the same letter the drive had before the disconnection.
Please advice if you have some documentation about this. And let me know if you have any thoughts about what really happened to prevent this in the future.
Thank you guys!!Hi, for the APP's drive it could had been assigned a new letter if the system did seen it as a new disk/partition.
The partition was on your esx's LUN on the SAN ? (not an iSCSI connection from inside a VM?)
Regards, Philippe
Don't forget to mark as answer or vote as helpful to help identify good information. ( linkedin endorsement never hurt too :o) )
Answer an interesting question ? Create a
wiki article about it! -
Has anyone had an issue with the app scramble with friends after upgrading to iOS 6. Tapping the screen will not select the tiles and hold them.
Yes I am having the same problem. I can't find any info about it and nothing seems to help. I am just posting this in hope that if it's a wider problem, there will be a quick solution.
Maybe you are looking for
-
Sound no longer working on AAO ZG5
I just reinstalled Arch on my ZG5 -- before I reinstalled everything sound-related was working by using snd-intel-hda and ALSA, all I had to do was add the line options snd-hda-intel model=acer-aspire in /etc/modprobe.conf, unmute the channels, and A
-
What do I need to do to replace my 80 gig HDD with a larger capacity HDD?
I have an older Mac mini, running OSX 10.6.8 @ 1.83 GHz w/2 GB ram. It is used primarily for email, iPhone photo storage, and online banking. Works, but now I am out of memory. rather than buy a new unit, I'd prefer to replact the 80 GB HDD with a
-
[CLOSED]How to create a custom messages
Hi All, I have a page and one save button .on press of save button, i want to show a custom message like "Applied changes are saved." Can anybody please elaborate how to create a custom message and how to show it through Controller. may i use OAExcep
-
Hi. Is it possible to maintain the internal no range for Hold documents? Regards, Srini
-
I think as soon as the world becomes aware of EVO:RAIL then folks will start asking what the use cases are. It's clear that there are couple of immediate use cases, but I'm betting that customers will bring to the table applications that perhaps we h