Issues after Vista---- Win7 migration

Hi,
I upgraded my T400s from Vista Prof to Win7 Prof 32 bit yesterday, and it did NOT go smooth. I had to start over after an error message given in the process. Anyway I ended up having to format my preload drive and installed there. Coming back up I pretty much had a generic Win7 installation, no traces of Lenovo drivers / software whatsoever. I pulled some from the companion disc and installed all I could through the Thinkvantage Toolbox.
I now have the following issues:
1. A device called Base System Device in the Other devices category, PCI slot 3 does not install. Driver not available for download. What device is this, so that I can download the driver manually?
2. Rescue & Recovery is not installed. I found the Rescue and Recovery© 4.3 Sysprepbackup Accessory Package for the Microsoft Windows 7, is this what I need?
3. Fingerprint Reader does not activate when I boot. I have enrolled the fingerprints, but do not get the option after boot. How can I activate it?
4. The windows boot manager comes up every time I boot. Can I disable it?
Appreciate any help!
Cheers, Thorbjorn
T400s | 2808-CYG | SSD | 4GB RAM | Windows7 Prof. 32bit
Solved!
Go to Solution.

tbar2112 wrote:
The Base System Device appears to be the card reader, I installed it and problem #1 disappeared.
Excellent catch, Thorbjorn.
I had those BSD missing-in-Devices issues, and then for other reasons had installed the latest Card Reader (for the SD slot in the front of G530.
I happened to notice the BSD indications had gone away, later, but didn't connect the two occurances.
Base System Device indeed.
Thanks,
C.

Similar Messages

Issue after public folders migration Ex 2013 Cu3

Hello,
after successful PF migration, Ex2010 to Ex2013 I could see everything working from Outlook.
Anyway, I wanted at the very end to compare folder statistics and permissions against legacy settings.
Unfortunately, at about 600 folders I could get error:
The security principal specified is already on the permission set.
I've checked one of affected folders via Outlook / Folder Permissions and could see doubled entries for same identity (imagine, two times the same account with the same Owner permissions) I've tried to delete it ;) but the result is that folder
lost completely the permissions and I can NOT change it over shell, ECP or Outlook anymore even I was the former owner.
So, is there something like ExFolders so I could reset the ACL on the affected folder ? It is quite urgent for me as I need to decide if I should do rollback or keep it as it is risking some future issues ...
Thanks
Peter
PeBe

Hi,
As we know, ExFolders is not updated.and it is not supported for exchange 2013 currently.
I recommend you can create a script to re-add the permissions for all the folders.
If needs urgent, I recommend you post the requirement on Script forums :
http://social.technet.microsoft.com/Forums/scriptcenter/en-US/home?category=scripting
Thanks.
Niko Cheng
TechNet Community Support

Read only access issue after time machine migrate

Having a small issues on my new rMBP. I recently switched from my MBA to this newer rMBP and I previously had a Time Machine backup that I migrated over. For some reason though..when accessing my external hard drive it keeps asking to authenticate the user and I have to put in a password anytime I edit or add files to this external drive. I was also having issues running some commands in Terminal where it said I didn't have access..my current user shows up as being admin but I'm not entirely sure how to get past all these restrictions and have read/write access to everything.

So I looked at the above images and noticed that the disk labeled "HD-PATU3" is almost entirely full - only 5GB of 1TB is available - so it's essentially "full".
You said that this drive "was" used for Time Machine backups - is that still what you want to do with it in addition to your own files? If you do still want to use as TimeMachine that's OK, but you can't predict what TM will do with it as far as space goes unless you split the disk into two partitions. TM knows how to remove old "snapshots" to make room for new backups, but do you need space on there as well for your own stuff? Some people think it's not a good idea to mix your own stuff and TM stuff on the same disk volume, so that has to be your decision to do.
You might want to take a look at http://pondini.org/TM/6.html and read what he has to say (Pondini is a TM expert/god/phsychic - basically he recommends splitting up the drive into two partitions - one for TM and one for you - that way things are easier for your data as you don't have to live with issues the TM enforces on it's backup volumes. So answer the questions:
     1. how large is the internal drive on the rMBP?
     2. how much do you want the external drive to have for backups and your stuff - in fact is there a reason why you don't have all
         stuff on the internal drive? There are performance penalties for having your data and TM backups on the same disk. You
         probably have a nice large internal disk on the new rMBP so is this really what you want to do?
     3. Depending on the answers we can get more specific to solve your issue(s)
later......

VPN Client Issue after Vista Upgrade

Not sure if this should be posted here, if not please let me know.
My organization has recently implemented Vista via an Upgrade-in-Place Process that takes an imaged system (Windows XP Pro - 32bit) and upgrades the system with a network image of Windows Vista Enterprise. Applications are left installed and herein lies my problem.
I'm using Cisco VPN Client 5.0.04, the client worked fine before the upgrade, after the upgrade, not so well.
While troubleshooting I noted the Cisco Systems VPN Adapter was no longer listed as being installed under Network Adapters in the Windows Device Manager, there was however an adapter, labled 6to4 adapter with an exclamation point. I went through the uninstall process for the Cisco VPN Client, rebooted and reinstalled. When trying to connect, I can use one of two pcf files (both are a back up of one another), the first connection profile goes through the motion of connection, tries to contact the security gateway, and states "Not Connected"
I enabled logging on the connection and tried again. Here's an excerpt from that log:
09:37:18.278 04/21/09 Sev=Warning/2 CERT/0xA3600038
Successfully added Key Usage fields to be matched.
7 09:37:19.792 04/21/09 Sev=Warning/2 CERT/0xA3600038
Successfully added Key Usage fields to be matched.
8 09:37:20.338 04/21/09 Sev=Warning/2 CERT/0xE3600001
Failed to launch application using cert pipe due to error: 0x800b010a.
9 09:37:20.338 04/21/09 Sev=Warning/2 IKE/0xE300009B
Failed to generate signature: Signature generation failed (SigUtil:97)
10 09:37:20.338 04/21/09 Sev=Warning/2 IKE/0xE300009B
Failed to build Signature payload (MsgHandlerMM:489)
11 09:37:20.338 04/21/09 Sev=Warning/2 IKE/0xE300009B
Failed to build MM msg5 (NavigatorMM:312)
12 09:37:20.338 04/21/09 Sev=Warning/2 IKE/0xE30000A7
Unexpected SW error occurred while processing Identity Protection (Main Mode) negotiator:(Navigator:2263)
Has anyone seen this behavior after an upgrade from XP to Vista? I'm I going to have to start with a fresh install? I appreciate any suggestions or advice.
Thanks,
Jimi

I finally figured out this problem and I feel it should at least be shared for another person who runs into this problem.
The problem was resolved by loading my personal certificates (the one that is read by the smart card reader and used to authenticate me on VPN) needed to be added to the personal certificates folder in the Local Machine layer.
I did this by opening up an MMC window --> Adding the certificates snap-in (in windows 7 it distinguishes 3 different layers, so choose the local user and the computer layer) --> and then copying the certificates in the personal folder located under Certificates - Current User into the personal folder located in Local Machine.
The most likely reason this happened to me is that the image I was working with had security settings blocking the certificates to be read at the current user level and not at the local machine level. Therefore, it's a problem with out image and the security policies put in place at the registry level and/or group policies placed in Active Directory. This is more of a workaround than an actual fix to the problem, but at least it pinpoints where the break is happening.
Now I can push the image back to the developers to review the security policies placed in the image.

Two of me as admin users in new MBA causes permissions issues after setup and migration

Normally I migrate to new Macs via firewire target mode. Flash forward to a new MacBook Air with no firewire.
I think I made a mistake in migration. I began setup as a new owner of the brand new MBA, then migrated my existing G4 PowerBook contents using Time Machine via USB.
The end result is that I have two accounts that represent me on the new MBA; the one I was guided into setting up when I first powered the MBA up, and the old user account from the PB. Although both are admin accounts, I have access to only some files when logged in as either admin. I tried repairing permissions, but no go. It also seems to hide files from the other account when searching in Spotlight.
It seems the only fix may be to do this all over again without setting up a new account in the MBA, but is that even possible? What would be the best way out of this mess so that I have one admin account with access to new files created under the new user and old files from the old PB user, as well as full permissions for all documents?

I concur with Colin: start over and use Setup Assistant. I used Migration Assistant once and it took me a week to clear up the mess. Although the two are basically the same process, by the time you use MA you already have an account established - hence the duplications - whereas SA moves over and creates one account.
And, for Colin:
looks like the OP inserted an impage/jpg of his post?

Issue in Web Service after the Windows migration from 2003 to 2008

My application is a web service and it was working fine in windows server 2003 .after it was migrated to 2008 ,the web service is working fine and but when its consumed in another web application which is also migrated to windows server 2008 ,its saying
"request channel timed out while waiting for a reply for 00:30:29.9820000.Increase the time out value passed to the request or increase the SendTimeout value on the binding .the time alloted to this operation may have been a portion of
a longer time out" error.The iis setting of my application in production has anonymous authentication enabled but the kerberos is not generating tokens and hence its also not working fine.When we disable the anonymous authentication the kerberos
token is generated but the application is prompting for credentails.Please help me to resolve the issue

Hi,
Since this issue is more related to IIS, I suggest you refer to IIS forum below to get more efficient support:
http://forums.iis.net/
Best Regards,
Amy

Vista/Win7 Bit-Matched Playback over SPDIF (and Crystalizer)

I have an SB XFi XtremeMusic and use it for my Microsoft Media Center all the way from XP MCE, Vista and now Windows 7 Ultimate (which by the way is robust, pretty mature with most (not all) issues sorted).
. I want to achei've automatic bitperfect output over SPDIF, the 'Bit-Matched Playback' in Audio Creation Mode option is there in both Vista + Win7. IE When playing music 44.k, TV/Videos 48K without using ASIO or WASAPI as Media Center does not support. However the 'Bit-Matched Playback' option appears to do nothing to the output other than disable the Crystalizer option (which doesn't work anyway over SPDIF), it always remains on the default format selected on the audio endpoint properties. Why is the option presented if it doesn't work? I understand in great detail the big differences in the XP/Vista+Win7 audio architecture and know dynamic sample rate switching worked on XP with some cards.
2. Also on a completely different tact why do none of the enhancements (mainly Crystalizer) not work on SPDIF if default Windows audio endpoint? (I know this is completely contrary to point above/audiophiles).
Really if neither of the above two points can work or be addressed then having an expensi've XFi card for SPDIF output is pointless as give no benefit over onboard SPDIF.
Cheers,
Simon

spl83 wrote:
Hello!
I have an Creative Audigy 2 ZS and Vista 64 bit Ultimate.
I ve installed newes audio Drivers form Creative Homepage (no beta).
Problem 1:
In Windows and in the Creative Audio Console i ve selected 5. Audio.
When i play MP3s in winamp i have no 5.!! I Only hear the sound in in the center and left / right front box.
Whats the Problem here
When i make the soundtest (5.) in vista everything is okay.
Problem 2:
I want spdif ac3 passthrough. I have an external AV Reciever conneted through SPDIF.
When i play an DVD on my computer, i want ac3 passthrough over spdif.
But the card only makes Stereo over spdif
When i make the SPDIF soundtest - the ac3 and the DTS test iss okay here.
can you tell me whats wrang here
Problem 3:
How can i enable CMSS 2 I only see CMMS in creative audio console!
When i Put the stereo fokus in CMMS the the boxes behind me.. it hase no effekt!! can put this regulator to the left ore to the right side and nothing happend
Problem It's the 2.2.0002 drivers. The 2.5.0002 ones are better, but Creative never released an installer for Audigy series.... Problem 2Windows Vista 64bit doesn't support SPDIF pass through. There's a chance it might work with the "dell driver trick" but the driver release notes clearly state it's not supported. Problem 3It's the 2.2.0002 drivers. The 2.5.0002 ones are no better. CMSS 3D effect only at the moment.Hope this helps

Broadcom WiFi issues after sleep/hibernate

This has been an ongoing battle that I have yet to make any progress on.
When coming out of sleep or booting back from hibernate the wifi will not connect to a network.
The error upon trying to connect to a found network is:
Windows was unable to connect to {network name}
After a hard reboot I can connect to any of the networks.
Tried disable/enable the wifi adapter, adjustments to power management settings. Tried fresh installs with various broadcom drivers, with and without power management settings, etc.
S10-3T N470, 2GB
Fresh install of Windows 7 Ultimate x86 (also tried x64)
Broadcom 802.11n Network Adapter
Date: 10/23/2009
Version: 5.60.18.41
Hardware ID: VEN_14E4 DEV_4727
Power Management disabled (Device Manager - "Allow the computer to turn off this device to save power UNCHECKED")
The networks I've tried are both home and work:
Home: AT&T UVerse 2Wire, Linksys WRT54Gv8 w/ WPA2-AES
Work: Apple Airport (unknown security, likely WPA)
Both work with Dell Latitudes, iphone, windows mobile with no issues
I'm fairly technical and knowledgeable but I haven't found what would be causing this issue or others having similar problems. I'm afraid if I can't resolve this soon I'll be retiring the S10-3T - which would be a real shame - so much potential but an unreliable wifi is a problem for me.
Perhaps the best solution would be to replace the Broadcom with another wifi that provides more regular drivers (intel) but I understand the bios has a very limited whitelist of allowed components (really lenovo?!).
Thanks all - GREAT forums - very very helpful/interesting discussions

similar issues exist within win7 with other cards especially the latest Intel cards: clarify the configuration setting for the wifi adapter and that both 2.4 and 5.2 bands are set to automatic and that your router is also set to automatic: depending on the router, the intel cards will or will not pick up 20 or 40 mgz signals
sorry if this sounds confusing but it is an issue with the card and the router playing nice and the combinations are great: a lot of it is trial and error so that by the time you sort it, you are unable to explain what you did!
I guess what I am suggesting is that it is the settings within the card and the router more than a driver issue (not that some drivers are not worse than others)
hope this helps you problem solve if these are areas you have not yet adjusted and tinkered with
s10-3 0647 Red plus 2gb ram

I am having start up issues after installing lion

after installing lion on my mac mini it is having major start up issues, sometimes it will not start up at all. Is anyone having the same issues?

After I used MIgration Assistant on my new Mac Mini, Lion would have kernel panics shortly after startup every time. I am pretty sure it was some virus software or network filterting software that ran background tasks that was causing the problem.
Can you startup in single user mode or safe mode?
http://support.apple.com/kb/ht1455
http://support.apple.com/kb/ht1492

Cannot download Win Updates after Vista Reinstall on New HDD

Hello!
This is what I have going on.....
Toshiba Satellite L305-S5942 original hdd crashed. Bought a new HDD and I've already installed Windows Vista Home. I was able to register my key and validate Windows. But now when I try to download the Windows Updates I get errors. I've researched the errors up until now. I've tried using FixIt and that didn't work. I've tried using the Readiness Tool and I get a "catastrophic error" error message. I've even tried downloading Vista SP2 standalong installer and I still can't get any updates.
I did see something about a Toshiba laptop owner having issues after reinstalling on a new drive and it said something about installing some driver called Intel Radid Storage Technology. I have not been able to anything about this anywhere else.
Does anyone have a solution for the issues I'm having? Does changing the HDD from original really affect me from getting Win Updates even after I've already validated my Windows Key?
Solved!
Go to Solution.

Satellite L305-S5942
Sounds like you have restored to a drive with advanced-format technology. What is the exact model of the drive? We'll look it up.
In the meantime, try installing this new storage driver.
Intel Rapid Storage Technology
See my message from one year ago.
After Restoring to New Hard Disk, No Windows Update - a Fix
-Jerry

Iphone 5 issues after IOS 8.2 update: my husband's phone and my phone get the same phone calls ONLY when we are home. Any suggestions on where to look to fix this?

Iphone 5 issues after IOS 8.2 update: all the iphones in the house receive the same phone calls ONLY while we are at home. Any ideas on how to fix this?

That is a new "feature" described in Connect your iPhone, iPad, and iPod touch using Continuity
You can turn it off by going to Settings > FaceTime and changing "iPhone Cellular Calls" to off

Issue with LCM while migrating planning application in the cluster Env.

Hi,
Having issues with LCM while migrating the planning application in the cluster Env. In LCM we get below error and the application is up and running. Please let me know if anyone else has faced the same issue before in cluster environment. We have done migration using LCM on the single server and it works fine. It just that the cluster environment is an issue.
Error on Shared Service screen:
Post execution failed for - WebPlugin.importArtifacts.doImport. Unable to connect to "ApplicationName", ensure that the application is up and running.
Error on network:
“java.net.SocketTimeoutException: Read timed out”
ERROR - Zip error. The exception is -
java.net.SocketException: Connection reset by peer: socket write error
at java.net.SocketOutputStream.socketWrite0(Native Method)
at java.net.SocketOutputStream.socketWrite(SocketOutputStream.java:92)
at java.net.SocketOutputStream.write(SocketOutputStream.java:136)
at java.io.BufferedOutputStream.flushBuffer(BufferedOutputStream.java:65)

Hi,
First of all, if your environment for source and target are same then you will have all the users and groups in shared services, in that case you just have to provision the users for this new application so that your security will get migrated when you migrate the from the source application. If the environs are different, then you have to migrate the users and groups first and provision them before importing the security using LCM.
Coming back to the process of importing the artifacts in the target application using LCM, you have to place the migrated file in the @admin native directory in Oracle/Middleware/epmsystem1.
Open shared services console->File system and you will see the your file name under that.
Select the file and you will see all your exported artifacts. Select all if you want to do complete migration to target.
Follow the steps, select the target application to which you want to migrate and execute migration.
Open the application and you will see all your artifacts migrated to the target.
If you face any error during migration it will be seen in the migration report..
Thanks,
Sourabh

Authorization issue after the Support packs upgrade

We're having problem on authorization issue after the SP upgrade.
One issue if "You are not authorized to call up line item display" using FCH1 and FS10N tcodes.
And the SU53 showing problem on S_TCODE FAGLL03.
How are we going to solve this issue? We dont want to add this missing auth object on all our finance roles.
Thank you in advance.

How can i send you the trace file? What is your email address?
If I were you, I won't do that. Did you not ever sign some confidentiality agreement? I wonder.
Anyhoo... (copy right @ David)
What are the objects been caught in category RC=4, RC=12?
Relate them with functional aspect of the transaction (error screen)
Edited : You can paste RC=4, RC=12 objects here without customer specific value if you want to.
Regards,
Arpan Paik
Edited by: P Arpan on Aug 23, 2011 2:36 PM

I have the latest downloadable version of LR5. It crashed while it was createing 1:1 previews during an import. After a Win7(64) restart, it shows a message that LR needs to quit because it can't read the preview files and it will try to fix it the next

I have the latest downloadable version of LR5. It crashed while it was createing 1:1 previews during an import. After a Win7(64) restart, it shows a message that LR needs to quit because it can't read the preview files and it will try to fix it the next time is launches. I get the same message the next and every subsequent time it launches so I can't launch LR at all now.
I get that the preview file got corrupted somehow. Is there some way to fix this problem without building a new catalog?

Use Windows Explorer to open the folder containing your catalog. You will see a folder with the extension .lrdata. You need to delete that folder and then start Lightroom again. Lightroom will generate a new previews folder.

WiFi issue after 6.1.2 upgrade

I upgraded my OS to 6.1.2 and now I'm having troubles connecting to the internet at work. I did reset my network settings and inputted the appropriate password and still having issues. It identifies the network but when open safari or an app requiring internet connection it goes nowhere. Is anyone else having this issue. Does anyone know how to fix this problem. Keep in mind my connection works fine at home.

Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
iOS 6 Wifi Problems/Fixes
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Issues after Vista---- Win7 migration

Similar Messages

Maybe you are looking for