Issues connecting non-Cisco AP as a repeater to Cisco 1230

Hi,
I just spent the whole day going through the old posts and can not find anything that is relevant to our issue.
We just purchased batch of 20 1230 11b APs to be used a root APs in our wireless network. Our users connect to our network using non-Cisco APs as using "AP Client" mode of the AP. Some APs have combined "AP Client/Repeater" and this is where we have issues associating these users to the 1230 APs.
Mind you that the APs that have "AP client" mode or the USB WIFI adapters have no trouble connecting to the Cisco unit. Onlt the APs with combined "AP Client/Repeater" or "Repeater" modes do not associate.
So far we tested non-Cisco AP such as Dlink, Netgear and Trendnet.. none of them worked as a repeater.
Does any one any experiance with this?
Update: We also did some testing and tried to create a bridge between Cisco and non-Cisco AP without any luck. Again all 3 brands have been tested.
Thanks

That is a tough one.... what you will need to do first, is look at the settings in the repeater and match it as much as you can on the Cisco AP. Look at data rates, preamble, DTIM, etc.

Similar Messages

Does Cisco WAP4410N work as repeater for Linksys E4200 ?

Does Cisco WAP4410N work as repeater for Linksys E4200 ?
Hi,
i have Linksys E4200 and I need repeater for it ...
Can anybody help me with this issue ?
BR

Thx for answer
I tested it and it works as Wireless Client - computer connected by ethernet wire is OK, everything works (DHCP etc)
but when i turn on " Allow wireless station to associate" in WAP4410N settings of "Wireless Client/Repeater" it doesn't work at all
I mean clients on wireless side and on wire side too ( DHCP doesnt work , there is no communication )

Issues Connecting to certain websites

A week ago I noticed issues using the eBay and BBC news apps and gumtree website on my iPad. I thought it was just a glitch with the internet yet a week later I am having the same issues. On trying them with my PC (wired connection) it also has the same issue accessing the above sites. The pages just don't load or a very slow. This seems to be the case on all devices attached to the home hub 4. I have performed a factory reset and performed a speed test which was satisfactory. Using a website that checks others status it tells me they are all up OK. I can only assume this is a connection issue. None of the usual websites inform of any issue. Can anyone advise best course of action?

there are various posts on this board about the subject if you use search facility you will find them all
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

MacBook Air intermittently has issues connecting to websites when wireless shows connected to the internet. The pages show that I am offline, but I can ping Google DNS. Windows PC, iPhone and Android phone have no issue displaying the same web pages.

MacBook Air intermittently has issues connecting to websites when wireless shows connected to the internet. The pages show that I am offline, but I can ping Google DNS. Windows PC, iPhone and Android phone have no issue displaying the same web pages.How do I solve this issue?

Go step by step and test.
1. Power off the router. Unplug it from the wall. Wait a while.
    Plug it back to the wall. Power the router on. Wait until all the lights are lit properly. It will take a while.
    Restart the computer.
    Start up in Safe Mode.
    http://support.apple.com/kb/PH14204
2. Empty Caches
    Safari > Preference > Advanced
    Checkmark the box for "Show Develop menu in menu bar".
    Develop menu will appear in the Safari menu bar.
    Click Develop and select "Empty Caches" from the dropdown.
3. Deselect Proxies if selected.
    System Preference > Network > Advanced > Proxies Tab
    Under "Select Protocol", uncheck any box if selected.
    Click "OK" then "Apply”.

Connecting non-powered speakers to iMac Intel

Is there a product that will connect non-powered speakers (that normally connect to a receiver), directly to the iMac Intel (mid 2006)? Either by a cable connector to the headphone port or USB?
I bought 2 Harman Kardon speakers super cheap last year, but have no receiver to power them. I guess I could buy a receiver but I don't really have the space for it. Today, I just bought the Griffin ProSpeaker Cable which connects non-power speakers to the iMac but found out it's for the older iMacs with 2.5mm port. The iMac Intels have a 3.5mm port.
Any suggestions?
iMac 20" Intel Core Duo Mac OS X (10.4.6) Powerbook G4 Titanium

Hi L.
Tried looking at the page your link directed me to but it was introducing a USB speaker. I know about the multimedia speakers for Apple computers but I'm looking at a way to use the speakers I already have.
I guess if there isn't a cable out there to help hook them up, I will have to purchase either a receiver and go through Airport Xpress or buy the multimedia speakers. (A bit more money than I was hoping to spend.)
Thanks anyways.

Connection of LC/APC fiber patch cords to Cisco Catalyst 6500 $ Cisco Access 3750 Switches

I have an LC/APC fiber patch cord infrastructure and I want to connect it to Cisco Catalyst 6500 & Cisco Access 3750 Switches. what type of transceiver should be used?
I read a note on Cisco website stating the following for Cisco SFP+ transceivers:
Note: "Only connections with patch cords with PC or UPC connectors are supported. Patch cords with APC connectors are not supported. All cables and cable assemblies used must be compliant with the standards specified in the standards section"

Thank you, but my question is that I have a single mode fiber patch cord with LC/APC connector while cisco stating a note that only use LC/PC or LC/UPC type of connectors with SFP+ transceiver.
So what type of transceiver should I use to connect LC/APC patch cord to cisco switches? Is there another type or SFP+ still can be used?

Restrict issue of non valuated materials

dear experts,
Is there any way to restrict issue of non valuated materials against a production order.
Regards,
krishna mohan

sir ,
After discussing with u about the issue again i discussed with my pm and got the exact requirement,
what exactly he want is the price of the material is 0 zero , it should not be allowed to be issued against a production order.
please tell me if we can do with configuration which is the best way or else we have to use any exit.
if we use exit we will check in MBEW table and field verpr, if the verpr field value is 0 zero then we will not allow else we allow the material to be issued.
regards
krishna mohan

Connect Non SAP Oracle DB and MSSQL DB to SAP BW 7.0 Orace 10g system

Hi All,
Well I have a scenario, where I have to connect Non SAP Oracle 9i DB and MSSQL DB (2000, 2005) to SAP BW 7.0 Orace 10g system.
There are all together 4 Non SAP systems to be connected.
Up till now I have understood that in order to have to integrate Oracle 9i to BW system - TSNNames.ora has to be updated, then create new Logical system, then Create Source system in RSA1 with all the required information, Create user at Oracle 9i end.
As far as MSSQL Server is concerned - Client Software + DB Shared Library has to be installed in BW server.
Could anybody please guide me in the complete Basis Activities including above to complete the process.
I tried to create Source System, the initial screen has fields - Logical System, Source System & Type and Release.
I have created the Logical system through Tcode SALE
How to create Type and Release - for DB Oracle 9i & MSSQL 2000/2005.
Does OS version of DB & BW also matters ? Do we need to have that information as well.
Thanks & Regards
Rupali S

Hi,
I am getting following error when I try to do TNSping
C:\Documents and Settings\bitadm>tnsping HRPRN815
TNS Ping Utility for 64-bit Windows: Version 10.2.0.2.0 - Production on 06-AUG-2
008 16:40:58
Copyright (c) 1997, 2005, Oracle. All rights reserved.
Used parameter files:
E:\usr\sap\BIT\SYS\profile\oracle\sqlnet.ora
TNS-03505: Failed to resolve name
This is my TNSnames.ora file content
BIT.WORLD=
(DESCRIPTION =
    (ADDRESS_LIST =
        (ADDRESS =
          (COMMUNITY = SAP.WORLD)
          (PROTOCOL = TCP)
          (HOST = poinmssapdev)
          (PORT = 1527)
    (CONNECT_DATA =
       (SID = BIT)
       (GLOBAL_NAME = BIT.WORLD)
HRPRN815.VSHODC.LNTINFOTECH.COM =
(DESCRIPTION =
    (ADDRESS_LIST =
      (ADDRESS = (PROTOCOL = TCP)(HOST = 172.25.8.79)(PORT = 1521))
    (CONNECT_DATA =
      (SERVICE_NAME = HRPRN815)
Do we need to manually update Listener.ora as well so as to function.
All this is not letting me create Source system.
Gives me following errors
TNS-12514 TNS:listener could not resolve SERVICE_NAME given in connect
descriptor
Cause: The SERVICE_NAME in the CONNECT_DATA was not found in the
listener's tables.
Action: Check to make sure that the SERVICE_NAME specified is correct.
TNS-12541 TNS:no listener
Cause: The connection request could not be completed because the listener is
not running.
Action: Ensure that the supplied destination address matches one of the
addresses used by the listener. Compare the TNSNAMES.ORA entry with the
appropriate LISTENER.ORA file (or TNSNAV.ORA if the connection is to go by
way of an Interchange). Start the listener on the remote machine.
Thanks & Regards
Rupali S

Issues Connecting To Bluetooth Speaker

Hello, I just purchased a passport on last Thursday and I am having issues connecting to a JBL bluetooth speaker. My passport is not even finding my wirless speakers when it is searching and it does the same thing when I refresh. Can anyone help me or give me any assistance? I have tried it with the discoverable on and off. Thanks,Stephen

Morning Frederic SALA,
Thanks for using Apple Support Communities.
For troubleshooting on this, take a look at this article:
Bluetooth Quick Assist
http://support.apple.com/kb/HT1153
Hope this helps,
Mario

ARD 3.6 Admin on 10.8 having issues connecting to 10.6 machine.

basically i have no issues connecting to any of the 10.7 machines in the office (all have 3.6 client installed now).
have no issues connecting to 10.7 machines that have dual monitors (most).
no issues with the few 10.4 and 10.5 machines i still have. nor any of the Xserves on 10.6 nor one single-screen 10.6 desktop i have.
BUT... there is *1* 10.6 machine that i can not connect to. the only main difference between it and other 10.6 machines is that it has dual monitors.
when it connects i only can see the external monitor showing up. then just pure black on the primary laptop screen. if i switch views to show one or the other... stays the same. a black screen on the main laptop display. if i switch to the black screen one and turn off 'scaling' i can only see the bottom half of the screen... but placed in the upper half of the viewer (with black beneath it). i can interact with it... but only with the things i can see on the bottom of the screen.
if i swap which is the "main" screen on the client in Displays (dragging title bar to other screen) ... there is no change. i can only see the external.
on a few of the 10.7 machines with dual monitors i *did* see a similar problem after installing 3.6 client. but after a restart they have been perfectly fine. only happened on a few machines though. not all.
so i restarted that dual-monitor 10.6 machine (it leaves the office frequently lately) and there was no change. turned Remote Management off / on. no change. resintalled the 3.5.3 ARD Client (no 3.6 on 10.6) ... no change.
the only change i did see... was that my ARD admin no longer can connect to it at all now (!!!). never times out either. just "Connecting" forever. however with direct client-style Screen Sharing i could connect. and there was no change.
the client machine itself is a Late 2009 MacBook (rubber bottom style). 2.26 C2D with 4GB RAM.
anyone else seen anything similar with 10.6 machines with dual-monitors connecting from a ARD 3.6 Admin on 10.8?
the machine itself can't be upgraded beyond 10.6 for the time-being (it needs a couple PPC apps with no replacements that are Intel). so that currently isn't an option.

I have similar issues.
10.7.4 running ARD 3.6. Connecting to laptops running 10.6.... "when it connects i only can see the external monitor showing up. then just pure black on the primary laptop screen."
Trying the same thing from ARD 3.5.2 running on a 10.6.8..... same problem.
Trying the same things from ARD 3.4 running on 10.5.8.... works perfectly well. Can switch between dual or either views......

How can ftp service on non-standard port be load balanced using Cisco ACE.

How can ftp service on non-standard port be load balanced using Cisco ACE.For example ftp service required on tcp 2000 port

Hi Samarjit,
you can do this by specifying the port number in the class map that you create . Please find the below mentioend config guide where you can specify the tcp/udp port , range or ports or even the wild card to match the port.
http://www.cisco.com/en/US/docs/interfaces_modules/services_modules/ace/v3.00_A1/configuration/administration/guide/mapolcy.html#wp1318826
Regards
Abijith

Issue connecting touchpad to WPA2 PSK network

I have an issue connecting my touchpad to any WPA2 PSK networks. The SSID is broadcast and other devices can connect but the touchpad errors with "unable to associate" even though I typed in the correct password. Any help is appreciated, and no I do not want to change the network settings since this device is supposed to utilize WPA2.
Post relates to: HP TouchPad (WiFi)

Hi Terabyte,
I don't mean to take over deltatuks thread but as we are having the same issue i'll continue!
I have power cycled the router and turned off/on the wireless on the device. I've just ran the tests and they all passed! including wifi! lol.
Still not working though.
This is very strange

Issue connecting with iTunes Match

Hi, i've got an issue connecting with iTunes Match. Most of the time iTunes doesn't connect to iTunes Match when launching the app. I just see the cloud symbol that indicates it tries to connect. And it just keeps on going. I then have to quit iTunes and relaunch it. Type in my Apple ID password. And still nothing. But around a third or fourth time I usually get a connecting going and then listen to music
And I'm not impatient. I give it some minutes everytime while opening and browsing the iTunes Store.
And the same thing happens after Sleep Mode. It is kind of annoying. Having open and close iTunes all the time.
Is there anything I can do? Am I perhaps doing something wrong? Is anyone experiencing the same problem or issue?
Thanks.

Hi,
Yes, your music remains on you computer.
Jim

There was an issue connecting to the server. please try again later. 124.

I'm trying to publish a site withdreamweaver as one of the 5 sites I get with my CC account using business catalyst, but I get the following error message "There was an issue connecting to the server. Please try again later. 124." whenever i try and connect which doesnt really help.
I'm logged in with the correct account in dreamweaver, and i have no issues publishing sites from muse using my CC account.

Hi Pirmin87,
There was a known brief outage a few days ago that could have resulted in this.
- http://status.businesscatalyst.com/
However at the moment everything should be connecting fine. If still an on-going issue please reach BC direct chat support for further investigation.
- http://helpx.adobe.com/contact.html?product=business-catalyst
Kind regards,
-Sidney

Airport Issues, Connects to BS But Not Internet

Hello, I hope someone can help me out here. I have tried several ways to fix this but still haven't had any luck. My issue is my Powerbook is having issues connecting to the internet through the base station. I can connect to other networks in my building and elsewhere with no issues. I get full strength on our connection and can connect to the base station but I cannot connect to the internet though our base station. Our BS firware is 5.7 my comp os is 10.4.7.
The thing that gets me is my roommate can connect fine with his MacBook Pro. I have tried everything from reseting, hard resetting, changed the settings, reset the PMU, etc.
Any help on this issue would be very much appreciated.
Thanks

Welcome to Discussions redlight24fps,
I assume you mean BS is referring to Airport Express Base Station? if so you should up date your Airport Express Firmware.
http://docs.info.apple.com/article.html?artnum=75422
Also make sure you have the latest Airport Software.
http://docs.info.apple.com/article.html?artnum=75422
hope this helps...

Issues connecting non-Cisco AP as a repeater to Cisco 1230

Similar Messages

Maybe you are looking for