Issues in Connecting Moto G to Flex 14 using USB
Hello:
I have Ideapad Flex 14 on which I have installed 64 bit Microsoft Windows 8.1. When I connect my Moto G (1st Gen) using USB port, it gets connected to the laptop, when I go to the specific folder of this Moto G using Windows Explorer, the whole folder structure including the Explorer window disappears. Then in couple of seconds, it appears again. This continues foreever till the time phone is disconnected from the laptop USB cord. I downloaded the Moto G driver from their website for Windows 8.1 and installed it. Still I am facing this issue.
To check it, I connected Sony Experia using USB and it is facing same issues.
Could you please guide me in resolving this issue?
Thanking you
CSJ
hello i face problem to connect my smart phone moto g to laptop.
Similar Messages
-
Firewire connection is not supported. Use USB to transfer songs...
Got message on my ipod saying "Firewire connection is not supported. Use USB to transfer songs" and then it says "Press Center to dismiss"
Restarted the ipod no use!
Connected with my PC no use! (its just charging) does not update of hooked to itunes)
Any ideas how i can fix this??
P.S I have tried cleaning the docking and the cable for any dirt still no use!Does it give you this error all the time or only when plugged in with the cable?
If it does it all the time, have you checked the dock connector for bent pins?
If it only does it when plugged in, have you tried a different cable?
Patrick -
Pc connectivity steps for nokia 3100 using usb port
hi
i am using dku5 driver and pcsuite to connect
my mobile to pc do i need to select getconnected button
every time i start the computer
please give the connectivity steps
i am new to j2meI am also having this problem with my mp3 player. When I plug it in by USB to my mac, the icon does not appear on the desktop and I can't find it at all in system preferences. I have tried it on a couple of different imacs and the icon pops up immediately. So I am thinking it is a problem with my computer....does anybody have any advice??
-
Connecting N95 to ovi suite using usb cable
I have just upgraded to windows 7. I installed pc suite and ovi suite just like i had before on windows XP. However when i try connecting using ovi suite and choosing the option of pc suite on the phone when connecting the usb cable i keep, ovi gives me the message "Please wait while USB drivers are installed on your computer" and stays in this state like for ever. I didn't have this problem before when using windows XP. Please help me
Attachments:
ovi_n95.jpg 302 KBI've had similar problems, but wait for the drivers to install, also sometimes my phone won't connect straight away, pulling the usb cable out of the phone and pushing it back in again quite quickly usually gets the connection to work ok !
If I have helped at all, a click on the White Star is always appreciated :
you can also help others by marking 'accept as solution' -
Why do I get a blue screen using USB communication?
Hello,
My problem is that sometimes I get a blue screen using USB communication. I guess that most of the time the problem is an overflow in memory, so I read all the data that is on the port with which I communicate. I read two ports so there are two similar VIs that are used. There is how I do it:
I also communicate with a logger to acquire 16 channels. I read the information from the logger in two different parts of the program at the same time. Maybe this can cause an issue, but could it cause a blue screen? This is how I do it:
I once had a blue screen after the VI was closed, so there is how I manage to close the communication when I quit:
Do you think there can be any problem coming from one of these parts of my LV project? If not, what else can cause a blue screen in LabVIEW?Langelier wrote:
Hello,
My problem is that sometimes I get a blue screen using USB communication. I guess that most of the time the problem is an overflow in memory, so I read all the data that is on the port with which I communicate. I read two ports so there are two similar VIs that are used. There is how I do it:
Are you using USB to GPIB (doubtful because you are using bytes at port)? But, just inc ase, I had this problem also with USB to GPIB, and it ended up being a driver issue I believe. If you are using USB to GPIB driver that was released with LV2012, search for the latest 2012 driver on NIs site, download it, and use that. See if it fixes your problem
CLA, LabVIEW Versions 2010-2013 -
Issues in mapping objects from java to flex - using flex4
Hi,
I have a class in java which i want to send to flex4 using BlazeDS as middleware. There are a few issues that i am facing and they are:
When sending the object across (java to flex), the properties with boolean data type having value as true gets converted to properties with value as false. Even after setting the value to true it still comes as false on flex side. Can't understand why this is happening.
When sending the list of object containing property with boolean data type, the object on flex side does not show those properties at all. As of there were no boolean properties in that object.
Last but not the least, When sending List<ContractFilterVO> contractFilterVOs to flex using remote call, the result typecasted to ArrayCollection does not show the holding objects as ContractFilterVOs but as plain default Object though having all the properties send, except the boolean one mentioned in above points. Basically it is not able to typecast the objects in arraycoolection but the same objects gets typecasted when sent individually.
In all the above points i am using Remote Service through BlazeDS for connectivity with Java. I have done a lot of this stuff in Flex 3 but doing it for the first time in flex 4, is there anything that Flex 4 needs specific. Below is the pasted code for reference purpose.
Flex Object
package com.vo
[RemoteClass(alias="com.vo.ContractFilterVO")]
public class ContractFilterVO{
public function ContractFilterVO(){
public var contractCode:String;
public var contractDescription:String;
public var isIndexation:Boolean;
public var isAdditional:Boolean;
* Rmote Part of code
var remoteObject:RemoteObject = new RemoteObject();
remoteObject.destination="testService";
remoteObject.addEventListener(ResultEvent.Result,handleResult);
public function handleResult(event:ResultEvent):void{
var contarctFilterVOs:ArrayCollection = event.result as ArrayCollection; //Point 2&3 probelem, if list sent form java
var contarctFilterVO:ContractFilterVO= event.result as ContractFilterVO; //Point 1 probelem, if only single Object of type ContractFilterVO sent form java
Java Object
package com.vo
public class ContractFilterVO implements Serializable
public function ContractFilterVO(){
private static final long serialVersionUID = 8067201720546217193L;
private String contractCode;
private String contractDescription;
private Boolean isIndexation;
private Boolean isAdditional;
I don't understand what is wron in my code on either side, it looks syntactically right. It would be great anyone could help me point out my mistake here. Waiting for right solutions...
Thanks and Regards,
JigarHi Jeffery,
Thanks for your reply, it did solve my query @ point 3 as well as point 2 where the objects in arraycollection were not geting converted and boolean properties did not appear when list of an objects were received. And hey, i did have public functions for properties defined java class, just forgot to mention here in post, sorry for that.
The solution you gave was right, but than what if i have a VO which has multiple List of objects coming from Java, than i would have to create an instance of each type of object on flex side this is too tedious, is'nt it? Is there any better solution... out there.
And jeffery do you some tricks up your sleeve for this Boolean issues to that i am facing in point 1... Still struggling with this one...
Anyone out there would be more than welcome to point my mistake, if any and provide tips/tricks or solutions...
Thanks again to Jeffery...
Waiting for more solutions sooner...
thanks and Regards,
Jigar -
Connect Mysql in Flex Using VB
Hai All,
Could any one tell me how to connect Mysql in flex using vb. I tried, but i am getting the below error.How to import mysql class.
Compiler Error Message: BC30002: Type 'MySql.Data.MySqlClient.MySqlConnection' is not defined.
Source Error:
Line 5:
Line 6: Public Class Database
Line 7: Public DBConnection As MySql.Data.MySqlClient.MySqlConnection
Line 8:
Line 9: Public Function DBNAME() As String
And i want to convert the text to voice, how to do this?? Any idea .. please help me
Thanks and Regards,
Arun KumarSystem.err.println("Exception: " + e.getMessage());You should do something more useful instead, like e.printStackTrace(). THe message of an exception doesn't always say very much.
You are probably getting a "class not found exception" signaling that the class com.mysql.jdbc.Driver cannot be found --- you need to somehow make JCreator aware of the JDBC driver. -
Dear All Has anyone found a break through with the issue of Connect to itunes to use push notifications
Did you get any help on this? From what I can see from surfing this site, it's a BUG that no one has offered a solution to. It sometimes happens after a 'reset' and going to ITunes does not offer a way to 'set up push notifications'.
-
Issue in connection with database using SQL Developer.
Hi,
I am facing a problem in connecting to a remote oracle database, below are the configuration setting which i am trying to use in sql developer to make the connection
TNS Configuration Details (SUDHIR)
SUDHIR=
(DESCRIPTION=
(ADDRESS=
(PROTOCOL=TCP)
(HOST=52.12.xxx.xxx)
(PORT=1526)
(CONNECT_DATA=
(SERVICE_NAME=sudhir)
User : system
Password : xxxxxxxxxxx
Database : sudhir
Connect as : Normal
I got the above credential details from Onsite team I need to connect this in my local sytem SQL Developer I am proving the connection as below
Hostname : 52.12.xxx.xxx
Port : 1526
Service Name : sudhir
Username : xxxxxxxxxxxxxx
password : xxxxxxxxxxxxx
I get following error when say test connection in sql developer.
"The Network Adapter could not establish the connection."
Please suggest me using the above details how to make the connection success. Please let me know.
Thanks
Sudhir
Edited by: BluShadow on 30-Mar-2012 11:56
data anonymised by moderator(o_0)
Hopefully for you, the machine is not reachable from internet !
Your giving online everything needed to log in as system ! that is quite dangerous. I guess the "Onsite team" would be pretty mad discovering that.
You should edit your previous post before too much people get to it.
Regarding your problem, I guess you can't get to the machine itself (maybe in a different network).
Can you try to ping it from your computer ?ping 51.17.130.121
This is a made-up IP, you'll have to replace with yours -
I have a Samsung VGA Monitor connected to my MacBook Pro using the Mini Display Port to VGA Adapter. How do I configure the computer so that it doesn't sleep when I close the lid of the computer.
Hi alangium,
Welcome to the Support Communities!
Resetting your computer's PRAM should restore your Macbook Pro's screen appearance.
OS X Mavericks: Reset your computer’s PRAM
http://support.apple.com/kb/ph14222
This article may provide some information about your Mini DisplayPort to AVI adapter. Have you tried to connect a different VGA monitor to your Macbook to see if you get the same results?
Apple Mini DisplayPort adapters: Frequently asked questions (FAQ)
http://support.apple.com/kb/HT3382
18. What is the maximum resolution available for use with the Apple Mini DisplayPort to VGA adapter?
The resolution available with the Apple Mini DisplayPort to VGA Adapter is 1920 x 1200. VGA displays that use higher refresh rates (such as 85 Hz) at resolutions of 1600 x 1200 or greater may not generate video properly until you lower the refresh rate.
Apple computers: Troubleshooting issues with video on internal or external displays
http://support.apple.com/kb/HT1573#5
How can I detect displays?
If the detect displays option is not available, hold down the Option key while you are in the Display pane.
How do I select additional resolutions on my display?
You can use the Display pane of System Preferences to specify how your display works. Not all options appear for all display models. By default the best resolution for your display will already be selected in System Preferences.
To select a different resolution, use the Scaled option. Some additional resolutions may be available when you hold the Option button.
I hope this information helps ....
- Judy -
In device manager it shows an error code 32' using iPhone 5 related to Apple Tv I believe is when this started, I am thinking I can DL the file and install
biut I am not sure how to properly do this.
Also I use my LTE to tether (paid) to my LapTop as well, The issue I am having, I cannot get the USB to work as a network connection. However using the WiFi method works fine but I rather use the sync cable at times such as when I am charging the phone and/or wishing to not trainsmit my ssid for others to see even though I do use a password.
Last question about using the built in WyFi tether connection, Is it posable to remove or ake the annoying blue indicater bar at the top disappear? This blocks from doing certain tasks that forces me to shut off the HotSpot app. to allow me to pull down the info bar at the top, Please Help ThanksIn device manager it shows an error code 32' using iPhone 5 related to Apple Tv I believe is when this started, I am thinking I can DL the file and install
biut I am not sure how to properly do this.
Also I use my LTE to tether (paid) to my LapTop as well, The issue I am having, I cannot get the USB to work as a network connection. However using the WiFi method works fine but I rather use the sync cable at times such as when I am charging the phone and/or wishing to not trainsmit my ssid for others to see even though I do use a password.
Last question about using the built in WyFi tether connection, Is it posable to remove or ake the annoying blue indicater bar at the top disappear? This blocks from doing certain tasks that forces me to shut off the HotSpot app. to allow me to pull down the info bar at the top, Please Help Thanks -
Hyperion Smart Cut Session Issue streaming multiple reports at a time using
This is a lengthly post with details, Please review with Patience:
We are trying to integrate Workspace based web Analysis reports within our intranet portal, thru portlets (made from individual workspace smartcut link), so that users can customize their page as needed, Once they login thru intranet, Cookie is set and passed to succeeding smart cut links via secured http headers. This part is fine, but mainly running into issue with streaming several multiple web-analysis reports at a time,+ we are using Iframe to display and stream multiple individual reports on to one page, but unfortunately all Iframes are sharing one session rather than creating individual session, mostly because of limitation of current web analysis system architecture and IE browser behavior with sessions .
Which Hyperion reporting tool does allow to stream multiple reports at a time? ideally we want to create Iframe of each workspace report so that users can customize and pick portlets as needed. To stream multiple reports at a time.
Problem Description: Hypeiron Web Analsysis, Smart cut reports incorrectly rendering images and intermixing dash boards on POV changes upon multiple reports being diplayed at one time thru Iframe's, issue seem to mostly relate to Hyperion using single session rather to multiple session when displaying several web reports at a time.
Steps Needed To Reproduce:
User logs into workspace.
user click on expolore and able to view the report without any issues.
When right on any of the report and select properties.
Select the SmartCut url and paste it in the Internet explorer.
The webanalysis report opens without any issues.
Similarly user copies the smartcut url for a different report and paste the link on a different tab or new window of same browser.
The report on the first tab gets over written of the report of the second tab of the browser.
The issue happens when two different reports and opened on a browser with multiple tabs. The reports get over written.
Oracle development answer:
In the described scenario opening new browser window does not spawn a separate independent browser session. A new browser window is supplied with URL pointing to the same domain, so all browser cookies including the "ORA_WA_SID" (WA session cookie) are shared between the windows. But multiple application instances cannot run in the same browser session simultaneously because of session sharing. This is not actually a defect, but rather a limitation of current system architecture and browser behavior. And there is no way to fix it programmatically on the product side.Hi MeHyper,
Your current arrangement puts most of the session handling and persistence on the client. This forces you to accept whatever the client decides to persist and propogate between browser elements (in this case iframes).
My approach would be to:
Consider coding your portlets to manage the sessions. Manage using a somewhat stateless strategy so that each request to the server requires a login and connect, retrieve, and disconnect. Each Iframe should access a different portlet url (or provide a different query) based on its content.
This way, in theory, you can invalidate the sessions and related cookies and update the various report elements independently.
Is smartview out of the question here?
Regards,
Robb Salzmann -
I have been having trouble with my iphone 4 for the past day . i tried to update it to 7.0.4 then the screen went blank and it keeps telling me to connect to itunes . I have connected it to 2 computers , using different cords and it doesnt recognize it . It says it is in recovery mode and i need to restore . after clicking restore it says that my iphone cannot be restored . I am very frustrated because i have been online searching for solutions all day and nothing seems to work . As soon as i turn on my phone it goes to the apple logo for about 2 seconds then the connect to itunes screen . SOMEBODY PLEASE HELP ! my phone is my life and i need it back on .
Connect the device to iTunes and restore from the most current backup.
If the issue continues, restore as new. -
When you try to install RDS role on server 2012 R2 using standard deployment, this issue may occur (Figure 1).
“Unable to connect to the server by using Windows PowerShell remoting”.
Figure 1: Unable to connect to the server by using Windows PowerShell remoting
First of all, we need to verify the configurations as it suggested:
1. The server must be available by using Windows PowerShell remotely.
2. The server must be joined to a domain.
3. The server must be running at least Windows Server 2012 R2.
4. The currently logged on user must be a member of the local Administrators group on the server.
5. Remote Desktop Services connections must be enabled by using Group Policy.
In addition, we need to check if the “Windows Remote Management “service is running and related firewall exceptions have been created for WinRM listener.
To enabling PowerShell remoting, we can run this PowerShell command as administrator (Figure 2).
Enable-PSRemoting -Force
Figure 2: Enable PowerShell Remoting
However, if issue persists, we need to check whether it has enough memory to work.
By default, remote shell allots only 150 MB of memory. If we have IIS or SharePoint App pool, 150 MB of memory is not sufficient to perform the remoting task. Therefore, we need to increase
the memory via the PowerShell command below:
Set-Item WSMan:\localhost\Shell\MaxMemoryPerShellMB 1000
Then, you need to restart the server and the issue should be resolved.
You can get more information regarding Remote Troubleshooting by below link:
about_Remote_Troubleshooting
If you need further assistance, welcome to post your questions in the
RDS forum.
Please click to vote if the post helps you. This can be beneficial to other community members reading the thread.i found another possible reason, this solution worked for me:
http://oyvindnilsen.com/solution-for-powershell-remoting-error-it-cannot-determine-the-content-type-of-the-http-response-from-the-destination-computer/
I tried to set up powershell remoting on a server and kept getting this error:
Enter-PSSession : Connecting to remote server failed with the following error message : The WinRM client cann
ot process the request. It cannot determine the content type of the HTTP response from the destination comput
er. The content type is absent or invalid. For more information, see the about_Remote_Troubleshooting Help to
pic.
After a bit of troubleshooting I discovered that the problem was that the authentication packets was to big (over 16k), this will cause WinRM to reject the request. The reason for authentication packets getting too big can be because the user is member of very
many security groups or in my case because of the SidHistory attribute.
The solution was to increase the MaxFieldLength and MaxRequestBytes keys in the registry under HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\HTTP\Parameters
If the keys does not exists you can create them, be sure to use the DWORD type.
I sat MaxFieldLength to DEC value 40000 and MaxRequestBytes to DEC value 32768 and rebooted the server. Problem solved. -
DPS 6.3.1.1 - Issues while connecting through SSL
Hello !!
I have a issue where my application client reported that they are unable to connect to the LDAP using SSL. Where as everything works fine in LDAP (non secured)
This is how our deployment looks.
Clients <=> Load Balancer <=> DPS (2 instance) <=> DS (2 masters)
The DPS is configured with DSP (data source pool) (with proportional algorithm of 50:50 to backend data sources). Client Affinity ("read-write-affinity-after-any") is configured for this DSP. The DSP is attached with 2 data sources.
So when the client connected in a secured port using LDAPS, they are unable to authenticate/search against this environment. No issues were found in DS logs for any of the bind/search requests. But in DPS, we noticed below log which i want to get clarification on.
Note: I have removed the hostnames/Ip where ever applicable from the logs.
=====================================================
[04/May/2011:12:24:39 -0400] - PROFILE - INFO - conn=1255260 assigned to connection handler cn=default connection handler, cn=connection handlers,cn=config
[04/May/2011:12:24:39 -0400] - CONNECT - INFO - conn=1255260 client=x.x.x.x:52461 server=x.x.x.x:636 protocol=LDAPS
[04/May/2011:12:24:39 -0400] - OPERATION - INFO - conn=1255260 op=0 BIND dn="uid=app_id,ou=applications,dc=example,dc=com" method="SIMPLE" version=3
[04/May/2011:12:24:39 -0400] - SERVER_OP - INFO - conn=1255260 op=0 BIND dn="uid=app_id,ou=Applications,dc=example,dc=com" method="SIMPLE" version=3 s_msgid=3 s_conn=ds_Master2:26560
[04/May/2011:12:24:39 -0400] - SERVER_OP - INFO - conn=1255260 op=0 BIND RESPONSE err=0 msg="" s_conn=ds_Master2:26560
[04/May/2011:12:24:39 -0400] - PROFILE - INFO - conn=1255260 assigned to connection handler cn=CH_ENV_catch-all_LDAPS,cn=connection handlers,cn=config
[04/May/2011:12:24:39 -0400] - OPERATION - INFO - conn=1255260 op=0 BIND RESPONSE err=0 msg="" etime=0
[04/May/2011:12:24:39 -0400] - OPERATION - INFO - conn=1255260 op=1 msgid=2 SEARCH base="ou=people,dc=example,dc=com" scope=2 filter="(uid=abcdef)" attrs="*"
[04/May/2011:12:24:39 -0400] - SERVER_OP - INFO - conn=1255260 op=1 SEARCH base="ou=people,dc=example,dc=com" scope=2 filter="(uid=abcdef)" attrs="*" s_msgid=498 s_conn=ds_Master1:26072
[04/May/2011:12:24:39 -0400] - SERVER_OP - INFO - conn=1255260 op=1 SEARCH RESPONSE err=0 msg="" nentries=0 s_conn=ds_Master1:26072
[04/May/2011:12:24:39 -0400] - OPERATION - INFO - conn=1255260 op=1 SEARCH RESPONSE err=0 msg="" nentries=0 etime=0
*[04/May/2011:12:24:39 -0400] - DISCONNECT - INFO - conn=1255260 reason="other" msg="Exception caught while polling client connection LDAPS.x.x.x.x.52461 -- javax.net.ssl.SSLException: Inbound closed before receiving peer's close_notify: possible truncation attack?"*
=======================================================
If noticed in the above logs, the initial Bind request via LDAPS is routed to Master 2. But the susequent search request (for user abcdef) is routed to Master 1.
And finally the DISCONNECT operation came (last line) without a proper unbind.
Is this alternate routing a expected behavior when client affinity is turned ON ? Is this exception causing the application's search failures ?
Please shed some pointers on this..
Thanks.
Edited by: Prasee on May 6, 2011 8:07 AMPls see inside:
Thanks for the reply. Yes the client is a loadbalancer in this case. So does it mean that this behavior (sending request to 2 different DS in a same connection) is expected ? I have few additional queries that arise from your reply :-)
Loadbalancing algorithm takes precedence "if the request that starts client affinity has not yet occurred"
Since its the load balancer that connects to DPS for any/every request every time., How do the DPS know whether a request that starts client affinity has occurred / not occurred ?Well, client affinity starts with a certain operation (not by establishing the client<->dps connection) as specified by your client affinity policy. In your case ("client-affinity-policy:read-write-affinity-after-any") it starts for all operations after the first read or write operation. DPS is not a (network) connection based router - so it does not route the client connection to the data source but forwards the client operations (request) on dedicated bind,read,write,.. connections to a data source selected by your load balancing and/or client affinity policy.
In our case, Its the same connection (conn=1255260) that receives bind and search request from the client. So when a connection is established, the client affinity should have got enabled and sent the bind request to Master 2 initially, so for the next search request, shouldn't it be sent to Master 2 again ?No, see above.
>
Sorry for these questions, I am basically trying to understand more on how client affinity works when a load balancer is in between.
Coming to the exception,
[04/May/2011:12:24:39 -0400] - DISCONNECT - INFO - conn=1255260 reason="other" msg="Exception caught while polling client connection LDAPS.x.x.x.x.52461 -- javax.net.ssl.SSLException: Inbound closed before receiving peer's close_notify: possible truncation attack?"
Does this abrupt shutdown of connection means the search response would have got dropped before reaching the end client (application) ?Yes, that may be possible ...
>
Thanks for your help !!
Maybe you are looking for
-
Live! Cam Voice won't run on Windows Vista 64-bit OS
I recently upgraded my OS to Windows Vista Home Premium 64-bit system. I downloaded the beta softwares (webcam driver & cam center) for my Creative Live! Cam Voice & everything looks fine until I run the Creative Live! Cam Center. Right after running
-
In safari I was not able to wish my frnds on their bdays in event section of facebook right top corner.. Is there any way to fix this..
-
my backlight is messed up, any solutions on what to do?
-
How to store printer when not used for extended period.
Printer will remain in unheated summer cottage. I plan to remove print head with cartridges for storage in a heated home. Will the cartridges dry out and/or would ink congeal in printhead as one instruction says not to remove cartridges until ready t
-
External HDD: Shows not ejected properly when the drive is still present
Hi, I have a Seagate 500 GB external HD, the big one with power adapter. I connect to my MBP with a USB cable. Recently, every now and then, I am seeing the message "Your external disk was not ejected properly. Always make sure you eject blah blah...