Issues setting up WRT54G

I have Verizon DSL, and want to set up my Linksys so I can finally use my laptop the way it was meant to be used.
However, every time I try to set up my Linksys router, I have issues, and can't connect.
I broke down, and called Verizon. They walked me through setting my modem to bridge mode, and told me to set the router to automatically configure itself. (DHCP)
That configuration didn't work, and they instructed me to call Linksys tech support. ..who offered no help on the whole thing, just wasted my time.
Is it just me, or is setting this up with Verizon usually this troublesome?
Anyone have any fixes they could throw my way?

Do me a favor and hardwire your router to your PC, Can you log into the web utility??? Type "192.168.1.1" default username and password are "admin" if it still won't let you in leave the username empty and put admin for password.
Also disable your wireless card well doing this, Go to start click run and type "cmd" enter in command prompt type "ipconfig" what does it tell you/does it work?
I am guessing you updated the firmware on the modem so you might want to do the same for your router here.
And well you are at it update your wireless card drivers.
GoodLuck
Matt

Similar Messages

  • Issue setting up eFax on HP Photosmart 7510 e-All-in-One "Problem connecting to internet"

    I'm having an issue setting up eFax on my new HP Photosmart 7510 e-All-in-One. I am following the on-screen instructions and receive an error "Problem connecting to internet" when trying to register the account. The ePrint service is working, and I can use the facebook app on the printer so it seems to be connecting to the internet. I am uncertain how to resolve the issue.

    Let's set a static IP address and external DNS for the printer:
    - Print a Network Config Page from the front of the printer. Note the printer's IP address.
    - Type that IP address into a browser to reveal the printer's internal settings.
    - Choose the Networking tab, then Wireless along the left side, then the IPv4 tab.
    - On this screen you want to set a Manual IP. You need to set an IP address outside the range that the router automatically sets (called the DHCP range). If you do not know the range, change the last set of numbers (those after the last '.') to 250
    - Use 255.255.255.0 for the subnet (unless you know it is different, if so, use that)
    - Enter your router's IP (on the Network Config Page) for the gateway.
    - Enter 8.8.8.8 for the first DNS and 8.8.4.4 for the second DNS.
    - Click 'Apply'.
    Now, shut down the router and printer, start the router, wait, then start the printer.
    After this you may need to redo 'Add a Printer' using the new IP address.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • I need help with a second hand iphone i purchased recently,i am having issues setting it up as it has is requesting for the icloud account that was used by the previous user

    i need help with a second hand iphone i purchased recently,i am having issues setting it up as it has is requesting for the icloud account that was used by the previous user

    Sorry.
    The iPhone is of no use until/unless the previous owner removes it from their account.
    You will need to find the prior owner or return the iPhone.

  • Having issue setting up email account on the iphone.

    having issue setting up email account on the iphone.  Going into settings mail, contacts, calendars...it goes back to the welcome screen.  How do I delete all email accounts and set up from scratch?

    I was having the exact same issue.  It was driving me crazy.  Just as a fluke, I tried logging in to my wife's account on the verizon.net website to se if I had a bad password or something.  As soon as I logged in on my computer, her account verified & installed on her iphone.  I have no idea why, but it worked.

  • Issues setting negative current on a KEPCO BOP 36-12D

    First thanks in advance for any adivce on this. I'm pretty new to labview.  I am trying to set a current remotely on a Kepco BOP 36-12. Manually the power supply works fine, and I have no issues setting a positive current, but the issue comes in setting a negative current. When I switch the voltage set point to negative I can set a current down to -5 amps, anything lower than -5 amps hits the voltage limit for a reason that I can't figure out.  Thank you again!
    Attachments:
    kepco alone2.vi ‏15 KB

    I have not worked with the Kepco BOP since the mid 90's, but we must have had 10 or so test set each with 6 BOP to create 3 phase current and voltage.
    As I recall they are nothing more than a power amplier and will follow the signal you supply within its limit. +/- its rails.
    We did not control them directly with LabVIEW. We controled them via standard function generators with LabVIEW.
    Is you problem with the setup of the BOP or is it with the device between the LabVIEW and the BOP.
    Can't tell what the missing subVI are doing from the VI you posted. 
    Omar

  • How to set up WRT54GS so the wired and wireless connections both work?

    I have a DSL line in to a Motorola modem.
    The modem is connected to the WRT54GS with an ethernet cable.
    When I connect my computers directly into the WRT54GS with an ethernet cable (there are four connection spots at the back of the box), I cannot go to the internet.  I have 3 computers plugged in, but none of them connect via Ethernet..
    Is there a setting on the router so that I can use the router for both wired and wireless connectivity?
    Added info: I tried to connect directly from the computer to the modem, but again, got no connectivity.  When I "chatted" with ATT, they told me the modem is set to "bridge", and that I could connect only one device.  I don't want to change this setting because I want to use the router for the wireless capability.  Besides which, I have more than one computer to connect to the internet.
    How come I cannot just plug in and go?  
    My firmware version is v2.07.1. 
    I don't know how to find out what hardware version I have.
    Other info is "DirectEthernet Connection, Speed: 100.0 Mbps, Signal Strength: Excellent, Status: Connected"
    Also "1394 Connection 3, Speed: 400.0 Mbps, Status: Connected"  
    I don't know what that's for, but thought it might prove useful to those of you who are knowledgeable about such things.
    Wireless is ok, but if I'm sitting right next to the router, I'd like to connect with Ethernet and take advantage of the better speed, etc.
    Thanks in advance.

    Just click this link.

  • IPhone 3GS 32gb - iOS4.0.1 - iTunes 9.2.1.4 - Sync issues / Set up as new

    Hello.
    I've had issues with my iPhone ever since I upgraded from iOS 3.1.3 to iOS 4 (and subsequently iOS4.0.1), to be more precise, my issues are with syncing my phone.
    When I upgraded to iOS4, I had an error and had to restore my iPhone while upgrading.
    Ever since that happened, every other day when I connect my iPhone to my iTunes, it is not properly recognized and I get the option to set up as new or restore from backup.
    90% of the time, restoring from a backup doesn't work and whether or not it works, afterwards iTunes forgot which apps/music/photos/videos/etc I wanted to sync, which means every time it happens, not only do I lose all SMS messages and App data, I also have to reselect the apps, videos and music I want to sync from scratch.
    It gets annoying now and I've tried several of the common solutions.
    - Uninstall/reinstall of iTunes, making sure I have the most common version.
    - chosing another USB port
    - reset all iPhone settings
    - reset all iPhone settings and wiping the phone content.
    I also cleaned up my App-library in which I noticed I had several duplicate apps ( for example: ExampleApp and ExampleApp.1.0.1 ).
    Nothing works and I'm getting frustrated over it. I don't lose my contacts because of the Outlook sync I have, nor mails because they are an imap account, but having a password-keeping app like 1Password which loses its data every other day is rather annoying.
    Is there anything else I can try?
    Does anyone else experience such issues?
    I cannot make Genius-appointments, as there is no Applestore anywhere near where I live in Germany. I could of course try and contact my phone-company but I am guessing they will direct me at the manufacturer.

    I had the problem where I got an unknown error when upgading from 3.1.3 to 4.0.1 last night. It put my phone into recovery & said that I had to restore it. Tried to twice but I still kept getting the unknown error message. Wasn't until I restarted my computer that it let me restore.
    All of my music, videos, contacts, etc are fine. But I found that none of my apps were restored to the phone. So I had to go back through & manually drag each one back onto the iPhone in iTunes and then re-sync it. But now none of the apps will load or open. I have tried switching the phone off & back on a number of times but it hasn't helped.
    Next I am going to try to restore again & see if that helps. From what I understand, the apps should have also been restored from the previous backup. Am not sure what happened in my case though

  • How do I set up WRT54G router with 4 computers and WVC54GC Wireless Camera

    Can anyone please tell me how to set up my Home Network with full security turned on?
    I have at least 4 neighbors that show up on my wireless connections list. I have a daughter that loves music and is constantly downloading viruses but only on one wireless connection. The rest of us want to be protected from that computer. My system consists of the following:
    One Linksys WRT54G Router
    Two Linksys WMP54G Wireless PCI adapters,
    Two Linksys WVC54GC Wireless Cameras  (Possibility four if the 1st two ever work OK.)
    Two Linksys LNE100TX PCI Ethernet Cards,
    One HP Ethernet Printer
    Three computers were connected by Ethernet cable and one was wireless. I did not change the admin password and I thought everything was working fine for a couple of years until I found that the wireless computer was acting as a “drone” and slowing everything down to a snails pace.  It could even turn itself on.
    I changed one of the Ethernet computers to wireless and decided that it might be time to also change the password and increase security.  Setting up security completely shutdown the wireless drone computer. I was OK with that, at least until I can reformat that harddrive.
    I then decided while I was at it, I would add a wireless camera (WVC54GC). I set it up using the software and Ethernet cable that came with it. After 6 tries I finally got the camera to work with the cable attached, but it does not work wireless and now none of the other computers connect any more. Is there a limit on how many connections? Should I reset the router and if so, do I disconnect the DSL modem? I’m afraid of the “drone” computer because I found some very bad malware on it. One in particular caused me to replace a hard drive.
    I’ve read page after page of network stuff on the Internet and I guess I just don’t know how to ask the right questions. I’m tired of fooling with this.

    hi , when u talk about security , are u referring to the "viruses" your daughters PC may be propogating to the rest of the network , or are u referring to external attacks on the router or your wireless PC"s ???
    In case u are referring to the "virus" attacks , the best you can do is install a good antivirus software on all PC"s and keep the virus definations updated....
    In case u are referring to the wireless security , i'd suggest that your use WPA2 personal. you can select WPA2 by going to the "wireless security" option.
    let me know if u need anything more.

  • Issue setting up iview - Need help

    Hi,
    I'm setting up an iview to surface a SAP BW report through SAP NetWeaver 7.0 (2004s)
    I've tested the iview with the following value in the "BEx Web Application Query String" property of the iview
    and am able to view my BW report in the portal iview as expected
    CMD=LDOC&TEMPLATE_ID=Z_CCA_UK_FIB_OPEX_TOTAL&VAR_NAME_1=ZPERRESP&VAR_VALUE_EXT_1=W123456
    I now want to use a variable so that the VAR_VALUE_EXT_1 property of the url is generated at runtime
    The VAR_VALUE_EXT_1 property is the user's login id (which must be uppercased for the BW report) so my url now becomes
    CMD=LDOC&TEMPLATE_ID=Z_CCA_UK_FIB_OPEX_TOTAL&VAR_NAME_1=ZPERRESP&VAR_VALUE_EXT_1=<User.userID[UPR_CASE]>
    The above however fails to give me a report.
    On debugging the url at the report end I can see that
    &VAR_VALUE_EXT_1=<User.userID[UPR_CASE]> is being presented to the report rather than the user's actual login id
    being substituted at run time as expected
    I'm using the information here
    http://help.sap.com/saphelp_nw04/helpdata/en/36/5e3842134bad04e10000000a1550b0/frameset.htm
    as a guide but am unable to get my report to work with the runtime url parameter substitution
    Has anyone come across this before and have a solution?
    Thanks in advance
    Krishna

    Hello,
         It sounds like you have almost everything set up but the vlan tagging on the ports. You will need to have inter-vlan routing disable which it seems like you have already done (enabling this feature will allow vlans to talk to one another). You may need to take a screen shoot of how everything is set up under L2 switch. Make sure all the ports are set to untagged and set to access port, you will need to put VLAN 1 on ports 1 and 2 and VLAN 2 on ports 3 and 4. As long as all the ports are set to access ports and untagged you should be fine at this point.
    If you are still having issues take some screen shoots so we can check and see how it is set up.
    Edit: while looking at the admin guide I see they are not called access ports. Guess its been a while since I've checked out a RVS4000.
    Hope that helps!
    Thanks,
    Clayton Sill

  • Issue accessing Setup WRT54GS

    I have 3 WRTGS routers,   1 connected to ADSL,,and the other two fanning out internet access ,via CAT/ and WLAN, in other offices in my house.
    Other than basic stumbling getting the right configurations all has gone well.  
    When I only had 1 WRT54GS, no fanning out, I could easily get to the setup page on my laptop, any of my laptops as I have 5, and one desktop.
    ISSUE: From my Desktop DELL Dimension 2400 (Broadcom 10/100 440x), the page loads SOOOOOO slowly if at all.  
    when I added the additional two WRT54GSs, the problem is even worse with them. I can get to the setup page, but when I click on other TABs in the setup.. IE gives up and can't connect to them.
    I upgraded my DELL Lan drivers.. and no improvement,
    Then I went to broadcom and got the latest driver from Broadcom since DELL's version was older.
    No help.. no change.. behaves the same.
    All 3 Linksys are differing model numbers all updated to their latest BIOS firmware.
    any ideas.. MTU turned to manual at 1500.
    I am going to give an external LAN controller a try next..  
    network performance seems ok.. from the DELL through the hub at 40mb/s..
    gus

    1)  Do you want to share printers, and also possibly files, with all computers on your network?  Or do you want 3 separate networks, with some routers setup for higher security?
    2)  Tell us more about how you have your routers setup and connected.  What Local IP addresses are you using?  Are DHCP servers on or off in each router?  How are routers wired - LAN port to Internet port, or LAN port to LAN port?
    3) What is the make and exact model number of your modem (not the router) ?
    Message Edited by toomanydonuts on 03-03-2008 04:04 AM

  • Issue setting chart title styles.

    Hello all,
    For some reason I am having an issue with setting underline and color fill for the title.
    -fx-font-size: 12px;
    -fx-underline: true;
    -fx-fill: red;
    the font size works, but the other 2 do not.  When in scene builder and this is put under "Style" I have to click .chart > .chart-title > -.text and it will switch the font size, but wont do anything else.
    Am I doing something wrong?
    Thanks,
    ~KZ

    I made a styleSheet and it worked, not too sure why it isn't working with setStyle, but hopefully someone can explain .

  • Issue setting up DisplayLink Monitor

    I have follow damn near ever guide I can find, tried to follow instructions I have read from other posts on this forum, but am just having no luck.
    Currently, plugging in the monitor gives me a green screen.
    I have udfbl installed and running in the kernel:
    $ lsmod | grep udlfb
    udlfb 17308 0
    syscopyarea 3447 1 udlfb
    sysfillrect 3747 1 udlfb
    sysimgblt 2232 1 udlfb
    fb_sys_fops 1371 1 udlfb
    usbcore 174164 4 udlfb,uvcvideo,ehci_hcd,usbhid
    I have xf86-video-fbdev installed:
    $ sudo pacman -S xf86-video-fbdev
    warning: xf86-video-fbdev-0.4.3-2 is up to date
    So I am not sure what the issue is, I am assuming it is in my xorg config.
    Below is my /etc/X11/xorg.conf.d/10-monitor.conf
    Section "ServerLayout"
    Identifier "DualSreen"
    Screen 0 "DisplayLinkScreen" 0 0
    Screen 1 "Laptop" LeftOf "DisplayLinkScreen" #Screen1 at the right of Screen0
    Option "Xinerama" "on" #To move windows between screens
    EndSection
    Section "Monitor"
    Identifier "LaptopMonitor"
    Option "Enable" "true"
    EndSection
    Section "Device"
    Identifier "LaptopDevice"
    Driver "nvidia"
    Option "/dev/fb0"
    EndSection
    Section "Screen"
    Identifier "Laptop"
    Device "LaptopDevice"
    Monitor "LaptopMonitor"
    DefaultDepth 16
    EndSection
    Section "Monitor"
    Identifier "DisplayLinkMonitor"
    Option "Enable" "true"
    EndSection
    Section "Device"
    Identifier "DisplayLinkDevice"
    Driver "fbdev"
    BusID "USB"
    Option "fbdev" "/dev/fb1"
    EndSection
    Section "Screen"
    Identifier "DisplayLinkScreen"
    Device "DisplayLinkDevice"
    Monitor "DisplayLinkMonitor"
    DefaultDepth 16
    EndSection
    Any help is much appreciated!
    Thanks

    Let's set a static IP address and external DNS for the printer:
    - Print a Network Config Page from the front of the printer. Note the printer's IP address.
    - Type that IP address into a browser to reveal the printer's internal settings.
    - Choose the Networking tab, then Wireless along the left side, then the IPv4 tab.
    - On this screen you want to set a Manual IP. You need to set an IP address outside the range that the router automatically sets (called the DHCP range). If you do not know the range, change the last set of numbers (those after the last '.') to 250
    - Use 255.255.255.0 for the subnet (unless you know it is different, if so, use that)
    - Enter your router's IP (on the Network Config Page) for the gateway.
    - Enter 8.8.8.8 for the first DNS and 8.8.4.4 for the second DNS.
    - Click 'Apply'.
    Now, shut down the router and printer, start the router, wait, then start the printer.
    After this you may need to redo 'Add a Printer' using the new IP address.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • Issue Setting Paths For Sickbeard

    Hi again everyone.
    Man I am having no end of trouble with my system at the moment. At first I had issues with SABnzbd but finally got it sorted but the thing that I am having a lot of trouble with at the moment is sickbeard. I only installed sickbeard this week from AUR.
    I already have a heap of tv shows that I want to add but I am unable to set the path to them or even add a new show and set the path to there.
    I want to set the path to /home/media/video/TVShows which is on my LVM but I can't get it set. I have even set the permissions at one point to 777 to try and get it to write there but it just won't.
    [media@media ~]$ ls -l / | grep home
    drwxr-xr-x 5 root root 4096 Sep 21 2010 home
    [media@media ~]$ ls -l /home | grep media
    drwxrwx--- 39 media users 4096 Nov 5 16:42 media
    [media@media ~]$ ls -l /home/media | grep video
    drwxrw-rw- 8 media users 103 Nov 5 02:22 video
    [media@media ~]$ ls -l /home/media/video | grep TVShows
    drwxrwxr-x 26 sickbeard users 4096 Nov 2 23:02 TVShows
    [media@media ~]$
    I'm just not sure how to solve this one and am hoping someone can help me get it solved.
    Last edited by morphjk (2011-11-05 10:05:14)

    Yes.
    In server.xml (under the config dir of the oc4j installation) there is an application tag for each web application installed. One parameter for the tag is path, which can be set to anywhere on the filesystem.
    Jonny
    null

  • Help please: Issue setting up collecting payments using Pay Pal

    Our form is created, our Pay PAL account is created and banking info confirmed.  Pay Pal account was registered and permissions granted.
    Defined the purchased filelds(1) tied to total amount due...and added a fixed 2.00 handling charge.  Basically everything appears okay.
    When I do the test the submit button is changed to proceed to checkout(and i see mc, visa, discover logos as well), but instead of going to screen where I can enter Credit card information it goes to pay pal login screen for our account.  Something is obviouslly set up wrong.  Can you help me with what could be the issue?  I was hoping to finish form setup soon.

    Hi;
    I would be happy to take a look.  You can share your form with me following these instructions http://forums.adobe.com/docs/DOC-2462 with [email protected]
    I don't' know what exactly you are seeing on the Paypal page, but the correct behavior after clicking "Proceed to checkout" is to be taken to a Paypal login page, it sounds like it is working correctly
    Since you are on your own computer where you sign into Paypal it would show your Paypal account/login like this:
    In the upper right it shows the amount of the transaction and if you sign in with a different Paypal account (can't sign in with the same account you registered) it will continue with the transaction, alternatively to test you can click the "Check out as guest" next to "Don't have an account" where you would enter payment information.
    If something else is happening your can share your form and I'll take a look.
    Thanks,
    Josh

  • Trying to set up WRT54G as access point

    I also put this on the Access Point Forum
    Situation:
    Using a cable modem.
    Installed a WIRED SMC barricade router next to the cable modem (just plug & play).
    Have 1 PC connected directly to port 2 of the SMC (PC works fine).
    Ran a cable from port 1 of the SMC to downstairs.
    Connected cable to the WRT54G.
    Via wireless, went into the WRT54G and disable DHCP (and saved settings).
    At this point I have can access the internet.
    But if I reboot my pc, I can see the WRT54G but do not get internet access nor even access it using 192.168.1.1 (I have to reset the WRT54G and then I can access it).
    Anyone know what I'm doing wrong?
    BTW, the SMC IP address is 192.168.2.1, so the only setting I change in the WRT54G was disabling the DHCP.
    Thanks
    Keith

    OK, if the SMC's IP is 192.168.2.1, then you would assume your IP would also be on that network. Are you performing a hard reset of the WRT (to factory settings)? If so that would probably explain why you can access 192.168.1.1, because factory rest is to enable DHCP on the 192.168.1.0 network, and your PC may be getting an IP from there before the SMC.
    Are the ports on the SMC router just switch ports (same as the ethernet ports on the WRT? If so, which port on the WRT are you connecting to the SMC? If you use one of the ethernet (not the WAN) ports on the WRT, and set it's IP in the 192.168.2.0 network you should be good. Disable DHCP on the WRT, and put it in Router mode, rather than Gateway mode (it doesn't really matter if you are not using the WAN port, as allyou are using are the ethernet ports and the wireless.)
    Your DHCP requests will still get passed over to the SMC.
    Message Edited by kevj on 02-09-2009 10:06 AM
    Tomato 1.25vpn3.4 (SgtPepperKSU MOD) on a Buffalo WHR-HP-G54
    D-Link DSM-320 (Wired)
    Wii (Wireless) - PS3 (Wired), PSP (Wireless) - XBox360 (Wired)
    SonyBDP-S360 (Wired)
    Linksys NSLU2 Firmware Unslung 6.10 Beta unslung to a 2Gb thumb, w/1 Maxtor OneTouch III 200Gb
    IOmega StorCenter ix2 1TB NAS
    Linksys WVC54G w/FW V2.12EU
    and assorted wired and wireless PCs and laptops

Maybe you are looking for