Issues upgrading WLC-2006
I cannot seem to get past the "transfer download start" (CLI) or "download" (GUI) phase of the upgrade on a WLC-2006 -- from 3.2.171.5 to 4.2.209.0. The transfer consistently times out at about 76% complete and I receive an error message, either "error writing to flash" or "error writing output file" (or something similar). Any suggestions/recommendations would be greatly appreciated.
You can't upgrade from 3.X to 4.2.209 direct. You need to upgrade to 4.0.206.0 first before going anyware. It's specified in the Release Notes.
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn422090.html#wp233853
Similar Messages
-
Hi, I am setting up a WLC2006 with 2 AP1010's. I cannot get the controller to see either AP. When I place the AP's on a network with a WLC 4400, they are recogized immediately by the 4400 at Layer-2 LWAPP.
Since the WLC2006 only works at Layer-3 LWAPP, do I have an AP icompatibility issue with the AP1010's(since I can only get them to work at Layer-2 LWAPP)?
Any advice is greatly appreciated.
ChrisAccording to Cisco doc., L2 mode is supported by WLC 44xx & 41xx and not supported by WLC 2006. And the 1010 supports L2 mode only, so the 1010 cannot works w/ 2006. You have to upgrade the AP to 1200, 1130 or 1240 or the WLC to 4xxx. And, don't know is there any future IOS / firmware can support it. Hopes this help.
-
Hi all,
Im having issues uploading code on a WLC in a remote location. The WLC is running 4.0.217.0 and im trying to upgrade to 4.2.209.0. I have checked the upgrade path from current to new version and there is no issue upgrading directly from one to the other.
The issue occurs when I try and upload via TFTP, the Controller starts the code upload and only downloads a portion of the code, starts the extraction then fails with the following messages:
-Sanity check fails
-TFTP failure while storing in Flash
-Failure while storing in Flash.
I've done a debug from the controller and this is the output:
Wed Oct 13 01:56:22 2010: RESULT_STRING: TFTP Code transfer starting.
Wed Oct 13 01:56:22 2010: RESULT_CODE:1
Wed Oct 13 01:56:26 2010: Locking tftp semaphore, pHost=10.198.136.12 pFilename=/AIR-WLC4400-K9-4-2-205-0-ER.aes
Wed Oct 13 01:56:26 2010: Semaphore locked, now unlocking, pHost=10.198.136.12 pFilename=/AIR-WLC4400-K9-4-2-205-0-ER.aes
Wed Oct 13 01:56:26 2010: Semaphore successfully unlocked, pHost=10.198.136.12 pFilename=/AIR-WLC4400-K9-4-2-205-0-ER.aes
Wed Oct 13 01:56:35 2010: tftp rc=0, pHost=10.198.136.12 pFilename=/AIR-WLC4400-K9-4-2-205-0-ER.aes
pLocalFilename=/mnt/download/local.tgz
Wed Oct 13 01:56:35 2010: tftp = 6, file_name=/AIR-WLC4400-K9-4-2-205-0-ER.aes, ip_address=10.198.136.12, msg=Unknown error - refer to log
Wed Oct 13 01:56:35 2010: upd_get_code_via_tftp = 6 (target=268435457 msg=Unknown error - refer to log)
Wed Oct 13 01:56:35 2010: RESULT_STRING: TFTP receive complete... extracting components.
Wed Oct 13 01:56:35 2010: RESULT_CODE:6
Wed Oct 13 01:56:39 2010: RESULT_STRING: Sanity check failed on file. The file was not downloaded completely!
Wed Oct 13 01:56:43 2010: RESULT_STRING: TFTP Failure while storing in flash!
Wed Oct 13 01:56:43 2010: RESULT_CODE:7
I've tried using a TFTP server (both 3Com and TFTPd) on a local server on site and its still fails. I've also tried using several servers
as the TFTP server and still no luck.
Does anyone have any idea why this is still failing? Could this possibly be a lack of space issue on the flash?
cheers
RobHi,
"Sanity check failed on file. The file was not downloaded completely! " - This error log is seen only if upgrade path is not right or if TFTP server which you are using does not support transfer of mor ethan 32MB file.
I understand that you have already tried many tftp servers. If in case, you haven't tried tfttpd32 yet, please download it and give it a try as Cisco recommends to use tftpd32 server.
Regards,
Madhuri -
Upgrade WLC 5508 to 7.4.121.0 problem
After I upgraded WLC 5508 from 7.2.111.3 to 7.4.121.0, all 3602i APs don't associate with the controller. All APs were working/associating with controller on 7.2.111.3 at same setting. IP address of APs are setup as DHCP.
The error message is "AP couldn't get IP address".
Any one has this type of problem when you upgrade WLC 5508 from 7.2.111.3 to 7.4.121.0.
Thanks,Hi,
This doesn't look like software issue.
You have to check why the APs are not able to get ip address. Try connecting a PC to a swtich port where one of these APs are connected and see if you are able to get IP on PC.
Also check if the DHCP server is reachable and if there are IP address in the pool assigned for APs.
HTH,
Thanks & Regards,
Ishant
*** Please rate the post if you find it useful *** -
We have a WLC 2006 that is setup to distribute IPs to wireless clients using the internal DHCP server. Occasionally, wireless clients can connect to the APs (four 1131AGs) but do not get IP addresses assigned.
Rebooting the WLC temporarily fixes the problem.
software version is 4.0.155.0
anyone experiencing this or know of a solution?
thanks!Apparently, others have observed similar DHCP behavior.
You may want to read a related thread ("Wireless Clients eventually not issued DHCP through WLC4404") in the "General" conversation section.
LINK:
http://forums.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=General&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.1ddc63fc -
Upgrade WLC 5508 Ver. 7.0.98.0 to Ver 7.6.110.0
i will upgrade WLC 5508 Ver 7.0.98.0 with License 50 AP. to Ver 7.6.110.0 will it ask to install license ?
No, It will not ask for again.
Just upgrade the software.
Regards
Dont forget to rate helpful posts -
What operating system can I upgrade my 2006 MacBook Pro 17" inch to if it has a 2.16Gh Intel dual core and 2G ram?
A Core Solo or Core Duo Mac can go to Mac OS X 10.6.8. A Core 2 Duo or better can go to Mac OS X 10.7.2.
(63169) -
Anyone having issues upgrading RFC apps from ECC 5.0 to ECC 6.0 ?
We are having issues upgrading our simple RFC app from ECC 5 to ECC 6.
we are using the librfc32u.dll ( 710_Rel) to make a simple call to return MARD table entries.
Runs great in our 5.0 system.
When we run against our 6.0 environment with the same dll, we get garbage back in the table results... (escape characters ).
We have tried downloading the latest 7.0 librffc* ( standard an u ) . We recompiled to embrace both unicode and non-unicode. ( fyi our 6.0 environment is unicode ) . All attempts have failed to date.
Has anyone else experienced issues trying to upgrade their rfc applications?david, were you able to fix this issue? i have a similar issue. we are upgrading from 4.6c to ecc 6.0. we use a c# program that connects thru sap connector for .net v2.0. it calls a rfc function module, it connects and passes some data, but not all data to the rfc.
any help would be appreciated.
thanks. -
Issues upgrading from 7.5.1 to 10gR3
We are having issues upgrading from Content Server 7.5.1 to 10gR3 running a Sql Server 2005 back end (based on Windows Server 2003).
We run through the upgrade process (which completes with warnings), but when we try to start the Content Server, we get the following error:
( 0%) Changing lengths of fields in table 'DocFormats'...
system 01.17 12:17:42.738 main When asking the database
for a list of tables, we got no tables back (internal)
01.17 12:17:42.753 main !
csUnableToLocateDatabaseTable,DocFormats-exception stack
intradoc.data.DataException: !
csUnableToLocateDatabaseTable,DocFormats
<snip>
Unable to locate table 'DocFormats' in database.
We are looking for advice from anyone who has been through this upgrade (in the same type of environment), or who have encountered this error or anything like it. The error appears to indicate a database access issue, but we have profiled the upgrade and startup, and have proved that the processes are reaching the database. We
have also tried the install against clean and complex installs, and have tried both JDTS and Microsoft drivers without success (same error).
We have spent many days on this, and have been working with Oracle support, but are starting to worry about how realistic the upgrade is.
Cheers,
Dave TOracle support suggested I execute an "exec sp_changeobjectowner 'DocFormats','<SchemaName>" command against the database.
I did this for the DocFormats table only.
When I tried to start the instance, the error message stated the DocFormats table was now missing.
Inside the database, the table 'Stellent.DocFormats' was visible through SQL Server management.
I then created a copy of this table as 'dbo.DocFormats' (as it was originally), and tried starting the process again (with the config.cfg variables you suggested).
It turns out the upgrade process can now see the DocFormats table and upgrade it successfully (The dformat column is now showing as varchar(80) ).
The startup process now fails at the very next table in the upgrade list (see output below).
Sounds like a database owner/permissions issue.
Any ideas from anyone with SQL Server experience?
Output from \bin\idcserver.exe -console -debug:
11:05:30.006 main SELECT dValue FROM Config WHERE dSection='DevUpdate' AND dName='MetaFieldLengthUpdateV8'
systemdatabase 01.18 11:05:30.006 main 1.79 ms. SELECT dValue FROM Config WHERE dSection='DevUpdate' AND dName='MetaFieldLengthUpdateV8'[Executed. Returned row(s): false]
systemdatabase 01.18 11:05:30.006 main SELECT dValue FROM Config WHERE dSection='DevUpdate' AND dName='FormatFieldLengthUpdateV8'
systemdatabase 01.18 11:05:30.006 main 2.56 ms. SELECT dValue FROM Config WHERE dSection='DevUpdate' AND dName='FormatFieldLengthUpdateV8'[Executed. Returned row(s): false]
( 0%) Changing lengths of fields in table 'DocFormats'...
systemdatabase 01.18 11:05:30.022 main getColumns DocFormats
systemdatabase 01.18 11:05:30.022 main 1.66 ms. getColumns DocFormats[Retrieved 3 columns.]
systemdatabase 01.18 11:05:30.084 main Table list: DocFormats
systemdatabase 01.18 11:05:30.084 main SELECT * FROM DocFormats
systemdatabase 01.18 11:05:30.084 main 2.83 ms. SELECT * FROM DocFormats[Executed. Returned row(s): true]
systemdatabase 01.18 11:05:30.100 main Delete DocFormats
systemdatabase 01.18 11:05:30.116 main drop table DocFormats
systemdatabase 01.18 11:05:30.256 main 148 ms. Delete DocFormats[Executed]
systemdatabase 01.18 11:05:30.256 main Connection with id of 'main.1' is removed from active connections with key of 'main'.
systemdatabase 01.18 11:05:30.256 main release pool connection
systemdatabase 01.18 11:05:30.256 main assigning connection
systemdatabase 01.18 11:05:30.256 main Connection with last id of <unassigned> is added to active connections with key of 'main'.
systemdatabase 01.18 11:05:30.256 main Assigned connection to this thread, took 0.49 ms.
systemdatabase 01.18 11:05:30.256 main Preparing connection for use, id initialized as main.2
systemdatabase 01.18 11:05:30.256 main dFormat varchar(80) NOT NULL, dConversion varchar(30) NULL, dDescription varchar(80) NULL|PK_DocFormats| PRIMARY KEY (dFormat)
systemdatabase 01.18 11:05:30.256 main CREATE TABLE DocFormats (dFormat varchar(80) NOT NULL, dConversion varchar(30) NULL, dDescription varchar(80) NULL, CONSTRAINT PK_DocFormats PRIMARY KEY (dFormat))
systemdatabase 01.18 11:05:30.256 main 7.25 ms. dFormat varchar(80) NOT NULL, dConversion varchar(30) NULL, dDescription varchar(80) NULL|PK_DocFormats| PRIMARY KEY (dFormat)[Executed.]
systemdatabase 01.18 11:05:30.256 main Connection with id of 'main.2' is removed from active connections with key of 'main'.
systemdatabase 01.18 11:05:30.256 main release pool connection
systemdatabase 01.18 11:05:30.256 main assigning connection
systemdatabase 01.18 11:05:30.256 main Connection with last id of <unassigned> is added to active connections with key of 'main'.
systemdatabase 01.18 11:05:30.272 main Assigned connection to this thread, took 2412 ns.
systemdatabase 01.18 11:05:30.272 main Preparing connection for use, id initialized as main.3
systemdatabase 01.18 11:05:30.272 main SELECT * FROM DocFormats
systemdatabase 01.18 11:05:30.288 main 4.26 ms. SELECT * FROM DocFormats[Executed. Returned row(s): false]
systemdatabase 01.18 11:05:30.288 main INSERT INTO DocFormats (dFormat, dConversion, dDescription) values('application/msword', 'PassThru', 'apMicrosoftWordDesc')
systemdatabase 01.18 11:05:30.288 main 2.93 ms. INSERT INTO DocFormats (dFormat, dConversion, dDescription) values('application/msword', 'PassThru', 'apMicrosoftWordDesc')[Executed. 1 rows affected.]
( 0%) Importing table 'DocFormats'...
systemdatabase 01.18 11:05:30.288 main INSERT INTO DocFormats (dFormat, dConversion, dDescription) values('application/pdf', 'PassThru', 'apPdfOptimization')
systemdatabase 01.18 11:05:30.288 main 1.87 ms. INSERT INTO DocFormats (dFormat, dConversion, dDescription) values('application/pdf', 'PassThru', 'apPdfOptimization')[Executed. 1 rows affected.]
systemdatabase 01.18 11:05:30.288 main INSERT INTO DocFormats (dFormat, dConversion, dDescription) values('application/rtf', 'PassThru', 'apRtfDesc')
systemdatabase 01.18 11:05:30.303 main 2.06 ms. INSERT INTO DocFormats (dFormat, dConversion, dDescription) values('application/rtf', 'PassThru', 'apRtfDesc')[Executed. 1 rows affected.]
systemdatabase 01.18 11:05:30.303 main INSERT INTO DocFormats (dFormat, dConversion, dDescription) values('application/vnd.ms-excel', 'PassThru', 'apMicrosoftExcelDesc')
systemdatabase 01.18 11:05:30.303 main 1.70 ms. INSERT INTO DocFormats (dFormat, dConversion, dDescription) values('application/vnd.ms-excel', 'PassThru', 'apMicrosoftExcelDesc')[Executed. 1 rows affected.]
systemdatabase 01.18 11:05:30.303 main INSERT INTO DocFormats (dFormat, dConversion, dDescription) values('application/vnd.ms-powerpoint', 'PassThru', 'apMicrosoftPowerPointDesc')
systemdatabase 01.18 11:05:30.303 main 1.69 ms. INSERT INTO DocFormats (dFormat, dConversion, dDescription) values('application/vnd.ms-powerpoint', 'PassThru', 'apMicrosoftPowerPointDesc')[Executed. 1 rows affected.]
systemdatabase 01.18 11:05:30.303 main INSERT INTO DocFormats (dFormat, dConversion, dDescription) values('application/vnd.ms-project', 'PassThru', 'apMicrosoftProjectDesc')
systemdatabase 01.18 11:05:30.303 main 1.53 ms. INSERT INTO DocFormats (dFormat, dConversion, dDescription) values('application/vnd.ms-project', 'PassThru', 'apMicrosoftProjectDesc')[Executed. 1 rows affected.]
systemdatabase 01.18 11:05:30.303 main INSERT INTO DocFormats (dFormat, dConversion, dDescription) values('application/vnd.visio', 'PassThru', 'apVisioDesc')
systemdatabase 01.18 11:05:30.303 main 1.63 ms. INSERT INTO DocFormats (dFormat, dConversion, dDescription) values('application/vnd.visio', 'PassThru', 'apVisioDesc')[Executed. 1 rows affected.]
systemdatabase 01.18 11:05:30.303 main INSERT INTO DocFormats (dFormat, dConversion, dDescription) values('application/wordperfect', 'PASSTHRU', 'apWordPerfectDesc')
systemdatabase 01.18 11:05:30.303 main 1.98 ms. INSERT INTO DocFormats (dFormat, dConversion, dDescription) values('application/wordperfect', 'PASSTHRU', 'apWordPerfectDesc')[Executed. 1 rows affected.]
systemdatabase 01.18 11:05:30.303 main INSERT INTO DocFormats (dFormat, dConversion, dDescription) values('application/write', 'PassThru', 'apMicrosoftWriteDesc')
systemdatabase 01.18 11:05:30.319 main 4.89 ms. INSERT INTO DocFormats (dFormat, dConversion, dDescription) values('application/write', 'PassThru', 'apMicrosoftWriteDesc')[Executed. 1 rows affected.]
systemdatabase 01.18 11:05:30.319 main INSERT INTO DocFormats (dFormat, dConversion, dDescription) values('image/graphic', 'ImageThumbnail', 'apThumbnailsDesc')
systemdatabase 01.18 11:05:30.319 main 2.12 ms. INSERT INTO DocFormats (dFormat, dConversion, dDescription) values('image/graphic', 'ImageThumbnail', 'apThumbnailsDesc')[Executed. 1 rows affected.]
systemdatabase 01.18 11:05:30.319 main INSERT INTO DocFormats (dFormat, dConversion, dDescription) values('text/html', 'PassThru', 'Hyperlink text document')
systemdatabase 01.18 11:05:30.319 main 1.84 ms. INSERT INTO DocFormats (dFormat, dConversion, dDescription) values('text/html', 'PassThru', 'Hyperlink text document')[Executed. 1 rows affected.]
systemdatabase 01.18 11:05:30.319 main INSERT INTO DocFormats (dFormat, dConversion, dDescription) values('text/plain', 'PassThru', 'Text file')
systemdatabase 01.18 11:05:30.319 main 1.66 ms. INSERT INTO DocFormats (dFormat, dConversion, dDescription) values('text/plain', 'PassThru', 'Text file')[Executed. 1 rows affected.]
systemdatabase 01.18 11:05:30.319 main INSERT INTO DocFormats (dFormat, dConversion, dDescription) values('text/postscript', 'Distiller', 'apDistillerDesc')
systemdatabase 01.18 11:05:30.319 main 1.60 ms. INSERT INTO DocFormats (dFormat, dConversion, dDescription) values('text/postscript', 'Distiller', 'apDistillerDesc')[Executed. 1 rows affected.]
( 17%) Changing lengths of fields in table 'ExtensionFormatMap'...
systemdatabase 01.18 11:05:30.319 main Alter ExtensionFormatMap
systemdatabase 01.18 11:05:30.335 main !csDbUnableToPerformAction_alter,\!csDbTableMissing
(internal) 01.18 11:05:30.335 main setExceptionCause threw: null
systemdatabase 01.18 11:05:30.335 main 15 ms. Alter ExtensionFormatMap[!csDbTableMissing]
systemdatabase 01.18 11:05:30.335 main Connection with id of 'main.3' is removed from active connections with key of 'main'.
systemdatabase 01.18 11:05:30.335 main release pool connection
(internal) 01.18 11:05:30.350 main !csDbUnableToPerformAction_alter,\!csDbTableMissing-exception stack
intradoc.data.DataException: !csDbUnableToPerformAction_alter,\!csDbTableMissing
at intradoc.jdbc.JdbcWorkspace.alterTable(Unknown Source)
at intradoc.server.IdcExtendedLoader.changeFieldLength(Unknown Source)
at intradoc.server.IdcExtendedLoader.expandFormatFieldLengthsV8(Unknown Source)
at intradoc.server.IdcExtendedLoader.extraBeforeCacheLoadInit(Unknown Source)
at intradoc.server.IdcSystemLoader.loadCaches(Unknown Source)
at intradoc.server.IdcServerManager.init(Unknown Source)
at IdcServer.init(Unknown Source)
at IdcServer.main(Unknown Source)
Caused by: java.sql.SQLException: !csDbTableMissing
... 8 more
Unable to alter table '!csDbTableMissing'. -
I would like to allow client to access wireless lan based on the client mac-address.
How I config it on WLC 2006 locally (not using radius server)? If yes, How mnay mac-address can be configured on the wlc2006?
Thanks.
DouglasHi Douglas,
Just wanted to add a note to Ankurs good info;
Maximum MAC Filter Entries
The controller database can contain up to 2048 MAC filter entries for local netusers. The default value is 512. To support up to 2048 entries, you must enter this command in the controller CLI:
config database size MAC_filter_entry
where MAC_filter_entry is a value from 512 to 2048.
From this good doc;
http://www.cisco.com/en/US/products/ps6366/prod_release_note09186a0080813b1c.html#wp42756
MAC Filtering
http://www.cisco.com/en/US/products/ps6366/products_user_guide_chapter09186a00805a6ad0.html#wp1040588
Hope this helps!
Rob -
Hi ,
Need one help from you.Please let me know Cisco WLC 2006 ( Running version 4.2.207) will support Access Point 1242AG ?
Thanks in advance.
Thanks & Regds,
LalitHi Sabastian,
Thanks for your reply.My question was I have a Wireless Lan Controller 2006 with 1030 Access Points registered to that and i wants to add AP1242AG.The Current version running on WLC 2006 is 4.2.207.I wants to add 1242AG Access Point to the 2006 WLC.Will my current WLC with current running version of image will support AP1242AG ?
Please reply.
Thanks & Regds,
Lalit -
pls have been having issues upgrading to the os 10.9. downloads encounter error when it gets to 955mb and starts over again….suggestions pls?
http://www.apple.com/support/mac/app-store/contact/
-
ISSU upgrade of Nexus 9508 impact on OSPF or HSRP?
It is my understanding that if you have dual supervisors, performing a software upgrade using the "software install" command will perform an ISSU upgrade and will be hitless to the dataplane. My question is, what happens to the control plane such as OSPF adjacencies and HSRP during the upgrade? For instance, if I perform this upgrade on the HSRP active switch, will there be a failover to my HSRP standby switch? What will happen to my OSPF adjacencies?
Thank you in advance!First of all ISSU is not yet supported on 9500 switches.
During the ISSU, all you protocol adjacency remains intact and works in conjunction with NSF/NSR capabilities of routing protocols which is enabled by default. -
Hi,
How is the correct steps for the upgrade of the WLC4400 from a version 4.1 to 4.2 version?
I backup the configuration running in the version 4.1.
I download, and put the file of the Software 4.2 in the TFTP directory.
I start the transfer from the TFTP to WLC.
The copy was succesfull.
I restart the WLC and Save the config.
But, the WLC lost the configuration (running the version 4.2), I connect to the console port and this showed the Wizard to start the initial configuration :S
What is the correct steps to upgrade WLC.Hi Ricardo,
This is a good doc with Step by Step info
Wireless LAN Controller (WLC) Software Upgrade
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00805f381f.shtml
Cheers!
Rob
Please support CSC Helps Haiti
https://supportforums.cisco.com/docs/DOC-8895
https://supportforums.cisco.com/docs/DOC-8727 -
Are there any known issues upgrading to 10.8.3 from 10.7.5 with Parallels Desktop already installed in 10.7.5?
Welcome to Apple Support Communities
Most of the applications compatible with Lion are also compatible with Mountain Lion, so you shouldn't have any problem. Mountain Lion supports the latest update for Parallels 7 and 8, so if you haven't got one of these versions, you should upgrade it before upgrading Mac OS X. That application uses extensions, so it may cause kernel panics
Maybe you are looking for
-
A whole world of problems....
Hello Adobe Edge Animate Forum, FIRST, I am requesting that an Adobe Edge Animate programmer please take a look at this discussion. I really love the program, and it's promise for what it does. I am spending countless hours in it, creating a more me
-
HT1386 iOS devices not appearing in iTunes Devices on Windows XP Pro PC
I used to have a Mac. Now I'm trying to sync my iOS devices with my new-to-me Windows XP computer, and they are not showing up in iTunes Devices. A Found New Hardware Wizard pops up, asking for drivers. I've tried it with my iPhone and my iPad. I hav
-
Iphoto - export pictures and import in an other mac
is it possible to export pictures which are stored on one mac in the iphoto lib and to import them an an other computer. So that i can manually sync the folders. Or does any one knows an other way to sync (both directions) Thanks Hans
-
Employee Address Missing after new localization patch
Hi We are implementing new BG(Spain) for our customer. Once we installed the new patches for the new BG We are not able to see the address of the US legislation employees. it is critical please advice if someone has faced similar issue thanks in adva
-
Windows Live Mail - Server unexpectedly terminates...
Hi. .Emails downloading fine previously then keep getting this error. Can see 'receiving emails' in bottom right status message but only 1 appears in Inbox. Then press Send / Receive and the rest arrive in Inbox but more often duplicated. Help plea