Isync 2.3 and Motorola V3r

Just buy a new Razr V3r (actual V3 also known as V3_O5) with firmware R4515G08.BD.43R.
Isync see it as V3 and accept to sync it but create 1 contact per phone number (1 contact with 2 phone number on the mac = 2 contact on the V3), doesn't sync all numbers and never sync adress and the worse is than it swap me all last name and first name.
I know their is the same problem with V3i.
Is anyone got a solution?
ps: sorry for my poor english, it's not my native tong.

A possible answer to the issue of the phone not getting all of the phone numbers is that the Razr will not synchronize numbers that have tags different than its phone book can identify. If you create a new contact on the Razr, you'll see the categories that it will identify for a new phone number. I you use the "other" tag in Address Book, or have any number tagged with a name other than what the Razr uses, the numbers will not be synchronized. I discovered this after I had a phone replaced, and had to go back in to the contacts in Address Book and re-tag the numbers that were missing on the Razr.
After doing so, all contacts synch'd the missing numbers. Unfortunately, as you pointed out, the Razr does not support addresses, and will only alphabetize by first name.
Happy synchronizing,
Gary

Similar Messages

Isync and Motorola V3c

I'm trying to sync my motorola V3c with isync, via USB, and after isync say's "Connecting", the phone says "Syncronizing, but after a while I always get this message:
[RAZR V3c] Connection to the phone failed. Please make sure that your phone is turned on. If this error occurs again, please restart your phone. Device "RAZR V3c" synchronization failed
I restarted the phone, I reset the sync history, What is wrong?
Midilab

I'm trying to sync my motorola V3c with isync, via
USB, and after isync say's "Connecting", the phone
says "Syncronizing, but after a while I always get
this message:
[RAZR V3c] Connection to the phone failed. Please
make sure that your phone is turned on. If this error
occurs again, please restart your phone. Device "RAZR
V3c" synchronization failed
I restarted the phone, I reset the sync history, What
is wrong?
Midilab
Midilab,
Read through this post,
http://discussions.apple.com/thread.jspa?threadID=598486
especially the last few exchanges and see if you find a solution. Resetting the iSync prefs AND deleting the noted directory files MAY be the answer.
I hope this works.
Pete

WLC 5508 and Motorola Symbol Handheld issue

Hi everyone, i have a weird problem and i hope you can help me guys!!
I have just migrate a Symbol-based autonomous wireless network to a Cisco Controller-based environment and everything apparently was working fine. However a few weeks later the installation was over, my customer reported they can't access to a server's shared folder.
This WLAN environment is installed in a warehouse and it is meant to support two different types of users: Regular Lap Top users and Motorola-Symbol Handhels. There are two SSIDs with static security methods (one with WPA+PSK and the other with static WEP key), Handhelds are joined to the SSID with static WEP key. So, here's the deal, this handhelds can join the network without any connectivity issues, roaming, signal strenght, etc. They can also ping everywhere. The problem is that when they need to access a server's shared folder and download files, handhelds displays a bad network path error message. If you do the same with a lap top, you can access the server´s folder with no problems. The handheld model is a Motorola-Symbol 9090 with Windows CE operating system version 5.0. Cisco infraestructure is as follows: WLC5508 running OS version 7.0.116.0 and AIR-LAP1142N-N-K9 series Access Points. In adition, i made a lab back in the office, and reproduce the problem. I tested with an autonomous AP same model and I can actually access a server's folder with no issue but int the very moment i test with a controller-based network i get the same result. I have made several changes in both, handheld and controller, based on a Cisco document for Motorola-Symbol and Cisco best practices. I also have placed a sniffer on my network but I can´t see any traffic when joined throught controller's WLAN. I placed it in the link between WLC and switch and between the switch and the Cisco AP.
Thank you all in advance
Rogelio

Mario:
I am glad that it worked.
well, enabling boradcast/multicast is not recommended if it is not bieng used. It saves bandwidth if it is disabled. However, if it is needed you can enabled it.
BTW, what I know with old versions (before 7.0.116.0) that enabling broadcast only does not work unless you enable multicast as well.
enabling multicast:
# config network multicast global enable.
I worked with one customer before where enabling the broadcast does not work until multicast is also enabled. Do you have the multicast config globally enabled already?

I install MIDlet on Nokia and Motorola Mobiles But....

I install MIDlet on Nokia and Motorola Mobiles But on Nokia it shows all directories/files but on Motorola MIDlet even not started.
My Application is for File Uploder and Downloader from web server.
Help Urgently.

hi
r u checking ur code on emulator of motorola , if yes check on device bec. motorala emulators doesnt have connection rights.
regards
akash
Indiagames Ltd
India
[email protected]

Bluetooth - MacBook Pro and Motorola w376g

I AM DIRECTLY RE-POSTING THIS FROM ANOTHER USER...i saw no answers there but i am having the EXACT SAME PROBLEM and REALLY want some help!
To everyone who are familiar with Motorola, I am having problems trying to connect with my cell phone via Bluetooth when I am attempting to sync files. When I set up the connection with my Macbook, the setup was successful when paired with each other. (Macbook and Motorola w376g) But when I use my phone and the Macbook, I couldn't connect with my cell phone with the Macbook because according with the Macbook, my phone "does not have the necessary services." Any ideas?
(Also, this isn't really to do with mac, but does anyone know how i can get realtones on my motorola w376g other than using the few that are at tracfone.com? I don't care if they are free or not, i just don't want to be stuck with poly tones on a phone that can play realtones)

Have you turned on *Bluetooth Sharing* in the Sharing system preferences pane?
If you have, what Services does your phone report as having in the Bluetooth system preferences pane? For file transfers it needs *OBEX File Transfer* and *OBEX Object Push*

Motorola V3r and iSync sends phone contacts to wrong folder

I want to sync my phone to a Group called Cell Phone in my Address Book via iSync. iSync has recognized my phone without a problem but I'm not having any luck directing the phone numbers from my phone to the Cell Phone Group. The phone numbers are going from my phone to the All Group. But it is pulling numbers from the Cell Phone Group and putting them in my phone. ??? In iSync I have the Contacts box checked and I used the drop down menu to specify my Cell Phone group.
Any ideas? Why is it pulling numbers from one group and importing them to another?

Apple have not provided this functionality for some reason.
You will see that there is a "Put events created on the phone into:" but not a "Put Contacts created on the phone into:" pop-up.
I don't know why Apple have not provided this option.
There is no workaround.

ISync and Motorola Razr2 V9 problem

Hi all,
I know there was a similar thread, but it's been archived so I can't post there. I just got a Motorola Razr2 V9x and tried to sync it with my Mac. I know I need a plugin for this. I have the plugin and iSync recognizes the phone. Whenever I try to sync I get an error message:
Connection to the phone failed.
Please make sure that your phone is turned on. If this error occurs again, please restart your phone.
The phone is on of course and restarting it doesn't help. When I try syncing iSync starts the process and the Bluetooth indicator light on the phone blinks briefly, then I get the error message. Any ideas what's wrong?

I just replaced my v400 after several years, a long service life for a cell phone.
Anyway, I never had a problem with iSync, except that at first I didn't "point" it to the Address Book directory I wanted to sync with. Are you sure the new entries are in the directory (or group) that you're syncing with? Click on the v400 icon in the iSync window and double check the Contacts drop down box.

ISync and Motorola RAZR

I have one of the original RAZR's and a MacBook Pro running 10.4.11. I've been using Motorola Phone Tools on a PC and syncing with Outlook without issue. When I bought my Mac, I wanted to sync with it instead. Tried exporting contacts from Outlook and importing in Address Book. No dice. Created entries from scratch. I deleted all contacts off my phone and used iSync. Many entries not copied to phone, and MANY entries in Address Book lose their numbers and addresses. I re-sync with Phone Tools to get original contacts back on my phone, and then match up entries from Address Book and phone manually. Did this:
http://discussions.apple.com/thread.jspa?threadID=1320120&tstart=0 <http://discussions.apple.com/thread.jspa?threadID=1320120&tstart=0>
Then run iSync again, and I get duplicate entries on both the phone and in Address Book. For a company that wants people to switch from PC's to Macs, this doesn't work very well.

The Verizon Wireless-supplied Motorola RAZR V3c is explicitly supported only by the latest release of iSync—version 2.2—which is a part of the Mac OS X 10.4.6 update. Prior to this release it was not, but could be used with the addition of third-party plug-ins.
However, there are three significant limitations inherent in this handset:
1. Calendar synchronization is not supported. This is a Verizon issue and may be resolved in future firmware updates from Verizon.
2. Verizon has reverted to its long-standing practice of disabling the Bluetooth OBEX profile, so that files cannot be exchanged between your handset and your Macintosh. They do this to preserve their ongoing revenue stream from pay-to-transfer options like Get it Now. Initially, this handset inexplicably did not have the OBEX profile disabled, but that 'oversight' has been 'corrected' in subsequent releases.
3. The V3c is a V CAST device, and as such, cannot be used as a CDMA wireless modem to connect to the internet. Many Verizon-supplied mobile handsets and smartphones do include a DUN [Dial Up Networking] profile, but V CAST devices do not. I mention this because the lack of DUN support may be a 'deal breaker' for Verizon subscribers like you.

Isync and Motorola L2

I have paired my Motorola L2 phone with my MacBook (unibody) and isync will not add contacts from my phone address book to the MacBook address book, however my contacts in my address will appear in my phone address book. The Apple web site says the L2 is supported. I have seen discussions where someone had the opposite problem, but mine is the opposite. Any suggestions? Thanks.

I have paired my Motorola L2 phone with my MacBook (unibody) and isync will not add contacts from my phone address book to the MacBook address book, however my contacts in my address will appear in my phone address book. The Apple web site says the L2 is supported. I have seen discussions where someone had the opposite problem, but mine is the opposite. Any suggestions? Thanks.

Remote and Motorola DVR Problems

I was connected to fios internet and tv on March 5, I have called tech support at least 8 times about the remote not working . I have had 3 boxes and 2 remotes sent to me and I still have the problem . I have a Sony Bravia LCD 40" TV
The first box was a Motorola QIP 72161 that came with the installation (remote worked intermittent)
I was sent a new remote same results
Sent a new box the old style 64xxxx remote worked but the hard drive was bad
New box Motorola QIP 72161 same problem
Tech support advised me I did not set up the remote codes properly (had same results it would work for a while then stop)
Tech support hung up on me
Tech support had me lower the picture settings advised me the picture was too bright and it interfered with the remote. She was very polite and helpful saying that this is a known issue and the problem is in the new Motorola boxes Sony, Samsung Sharp all are having this problem (worked all day but not at night)
Tech support told me I had to move the box from out from under the TV still did not work and that was all the solutions they had. By the way the remote works with the TV off. Played around with the settings on the TV ended up increasing the setting to vivid and the remote worked the rest of the night. So much for the brightness theory. But alas it did not work again this morning. Again the remote works with the TV off. Played around some more and you know when you first turn on the power to the TV you have a blank screen well the remote won't work then either. Although when I turn off and on lights I get a response one way Or another.
The attitude from the last techie is this is the way it is. I seems unfathomable that this is the response change your entertainment center watch a reduced quality picture or too bad.

You are welcome funkyybuda. This seems to be a "hit or miss" problem, some people say turning off the light sensor helps, some say turning off the "vivid" mode on the TV works, some say neither helps, etc. But apparently for some people, changing a setting on the TV really does help, I guess it just depends on your TV brand and model, or perhaps the specific STB you have. Strange.....but glad it worked for you
As to why it works, the Verizon STBs use infrared (IR) for the remote to control the STB. Apparently some TVs generate their own IR signal for certain settings, like vivid or the light sensor, and the Verizon STB sees these signals and this prevents their reacting to the IR signal from the remote. So doing whatever you can to remove the IR from the TV, or reduce it, seems to solve the problem. I wonder why all STBs that use IR, from all manufacturers and used in all systems, don't experience this problem with TVs that generate their own IR. Just one of life's mysteries I guess....
Justin
Verizon FiOS TV, Internet, and phone
IMG 1.6.0, Build 06.89
Keller, TX 76248

Bluetooth Portege 4010 - probs connecting to samsung and motorola phones

I have a portege 4010 with bluetooth. I am trying to connect to our two phones - a samsung sgh-e370 (newish) and a motorola V600 (2 yrs old). Both have BT. I have downloaded and installed the latest Tosh BT stack (4.0.something). Device Manager shows four tosh drivers under BT - all are OK. I have enabled discovery and permit connection on the tosh. I have done the same on the phones. When I run the "Add new Connection" wizard on the tosh, it finds both phones and they show up under devices in BT manager with the names I gave them on the actual phones. However, neither phone picked the tosh up and did not show the tosh as requesting the pin numbers on the phones.
The net result is I now have both phones showing up in BT manager, but if I click on either and choose use/connect I get back the error "Connection failed"
If I try to find the portege using the phones, the samsung finds it but the motorola does not. I can't get the motorola to pair with the tosh - it justs says "Unable to pair with portege".
Any help gratefully received.
RJ

Hello
I really don't know what is problem in your case but I have done this few times with my Motorola RAZR V3 and it works fantastic. The whole thing was finished for 1 minute. I hope you do this in right order but I write to you which steps I have done:
1. activate Bluetooth using FN+F8 key combination
2. install all new hardware components if necessary (few of them)
3. start Bluetooth stack
4. activate the Bluetooth on the mobile phone (discoverable)
5. choose Express mode > Next
6. Choose visible device listed in 'Bluetooth device list' > Next
7. Choose pass key for identification (1234)
8. Enter the key into mobile phone. Paring will be success
I have done it on this way and now I can send all documents to my Tecra. If you want to use it as modem you must do this:
1. After paring Go to Next and configure the internet connection
(provider number) > Finish
2. the new connection will be created in Bluetooth stack utility
3. you can start the dialing up with double click or click with right mouse button and choose 'Connect'

ISync 2.2 and Mac OS X 10.4.6 Update released: READ THIS before installing

Apple has released iSync 2.2 as part of the Mac OS X 10.4.6 Update package, and it has serious ramifications for current or first-time users of iSync. READ this information below before you perform the installation. This information is extracted from Technical Information Library article 303419, found here:
http://docs.info.apple.com/article.html?artnum=303419
iSync 2.2: Read before updating to Mac OS X 10.4.6 or later, or before first sync
iSync 2.2, included with the Mac OS X 10.4.6 Update, works with many phones. However, if you have an existing phone that you sync with iSync in Mac OS X 10.4 through 10.4.5, there are some important steps you should follow before you update to Mac OS X 10.4.6 or later, as well as after you update.
Before you update to Mac OS X 10.4.6 or later
1. Make sure that all of the contact and calendar data that you want to sync is on your computer.
2. Perform a sync with your devices before upgrading to Mac OS X 10.4.6 to make sure the information on your computer is up to date, and to resolve any conflicts between your devices and computer.
3. If you have modified iSync or installed third-party software to support your specific model of phone, or if if iSync 2.2 specifically adds support for your specific model of phone, you should consider removing your phone from iSync, undoing these changes and uninstalling that software before upgrading. Your phone will not work with iSync after applying the Mac OS X 10.4.6 Software Update and your third party software will need to be updated.
Note: Reudo's Sync for Mac is not affected and does not need to be uninstalled prior to updating.
If you skip these steps, you will see this message after upgrading: "Plug-in for this phone model is missing. Install that phone's plug-in if you want iSync to support it."
4. Make sure that your phone is configured to use its memory to store contacts instead of a SIM card. The steps on how to do this vary from phone to phone—consult your device's documentation for how to check its configuration, and if necessary how to change your phone to store contacts in its memory.
5. Make sure your phone has the correct date and time set.
6. Make sure that you have a current backup of your Address Book and iCal data.
Refer to the article for additional instructions and an illustrated example of the steps to perform before installing the update.

as the jump to intel progresses, so too will incompatibilities between PPC and intel mac. this will force us all to buy more apple.
G4 450DP Mac OS X (10.4.4) digidesign, motu, apogee

Problem syncing after updateing to iSync 2.2 and OS 10.4.6

I can't sync my Nokia 6620 after updating iSync 2.2! I get an error massage "The phone address book is full. Please delete some contacts on your phone or change filtering options and syncronize again."
I tried deleteing all the contact on my phone and syncronize without any luck! Tried to reseting the device and syncronize; no luck! I have even deleted the pairing and re-paired — nothing worked!!
Please help!!! I have a Dual 2 GHz G5/2.5 GB SDRAM. Thank in advance.
[img=http://img58.imageshack.us/img58/6893/isyncerror1zx.th.png]

I doubt that the problem is related to having more that one copy of AppleWorks on your hard drive, although there is no need to have more than one copy of the same version & language, i.e. US/North American English 6.2.9 (which also contains 6.2.8 if you purchased the retail box) or French 6.2.4/6.2.3.
Personally, I don't use the assistant to prepare an envelope as I set up my own template/stationary in ClarisWorks long before there were assistants. Others also have problems with the various assistants. Since it crashes when you go to Page Setup, the problem could be in AppleWorks (more likely) or in your printer driver (less likely). The first thing to do is delete the AppleWorks preferences. Deleting AppleWorks & reinstalling does not touch the preference files, they must be moved manually. It also is necessary to delete these preferences after every AppleWorks crash. See my user tip, AppleWorks has stopped working correctly, for more information. If this doesn't work, please post back, especially with the make & model of printer you are using.
Peggy
Edit: It is not necessary to post a question more than once. Since this is a user-to-user forum, people answer questions as they have time & ability. If you accidentally create a duplicate post you have up to 30 minutes or until someone posts a reply to delete the post by clicking the little trash can when viewing the thread. You can also edit a post by clicking the pencil.

IChat, Airport and Motorola surfboard modem

Hi all,
I cannot get iChat to work with a particular buddy after moving to another city with another Cable ISP.
I use an airport extreme basestation and have a motorola surfboard modem SB5120. The airport extreme is configured to connect to the internet using DHCP and both my iMac and iBook are configured to connect to the base station using DHCP. I've connected to this buddy succesfully every time on my old network using these settings.
What I tried...
I cannot work with static IP's because my ISP only works with dynamic IP's.
I've deleted com.apple.ichat.plist... No effect!
The motorola modem is not configurable in its html interface. My ISP however assures me it doesn't block ports and lets all traffic come through.
Quicktime streaming: automatic... iChat: no bandwidth limit
However...
Configuring the airport base station to not hand out IP adresses, is a FIX, but off course the iBook then cannot connect to the internet.
AND... when i DO configure it to hand out IP adresses and try to connect to several testadresses posted elsewhere in this forum (not just the Apple ones) i connect every time.
I don't know what is wrong, but it has me glued to my iMac for a week trying to come up with a solution. I've even combo updated my iMac with all firewire devices disconnected. I'm DESPERATE. .
Thanks in advance for your highly anticipated advice.
Greetz,
Rob

I have a simular modem and set-up.
The set-up is as follows:
Cable Modem <--> AEBS <--> Switch <--> Mac/Vonage/other pc/AE
I have all of my Mac/PC set to a static IP address (You configure each MAC/PC with a different IP address 192.168.1.100, 192.168.1.101, etc) Your DNS servers are required anytime you go with a static IP address. You can find out your DNS server by launching the Airport Admin Utility and clicking on network. The numbers will be greyed out and not in the normal white box that is listed.
Router should be 192.168.1.1
That should get you on the internet.
Next while your in Airport Admin, under internet confirm the following:
Connect using: ethernet
Configure: Using DHCP
IP address: (should be listed)
Subnet mask (should be listed)
Router address: (should be listed)
Next, click network and distribute ip addresses should be checked along with share a single ip address (using dhcp & nat) using the 192.168.1.1 addressing.
Next, under port mapping - map the following ports to your primary machines ip number (mine is 192.168.1.100)
5060,5190,5297,5298,5353,5678 as public ip address 192.168.1.100 and private as 192.168.1.100
If all that checks out, you have the same setting as I do with a very simular modem and I can connect with both PC and MAC users with no issues.
Does this help?
P.S. If you setup is the same as me and you still have issues, I had a friend that it was necesarry for him to call his local ISP and they made a change to his IP addressing-then all worked fine.

ISync 2.2 and SonyEricsson S700i

After installing the update 10.4.6 on my PB G4 1.5GHz; I could not sync my mobile phone SonyEricsson S700i using iSync 2.2. I tried it several times but every time just at the end of the sync process it gives a message "Error [S700i] There was an error pushing some changes to the phone. The synchronization may have been cancelled on the phone". I tried to solve the problem by deleting and re-installing the phone, deleting the preference file for iSync but I always get the same error message.
Any suggestions ?
PB G4 1.5 GHz Mac OS X (10.4.6)

Same Situation here with MacBook Pro and identical conditions.
Here, this is the first sync, and it failed right out of the box.

Isync 2.3 and Motorola V3r

Similar Messages

Maybe you are looking for