Iternet speed

my internet speed is so ubaleavable slow it eems like i must have the slowest in the country my average speed 56 k and believe that is about the same as dial up so bt why on earth is my internet speed so slow and i have tryed to get bt infinity but i cant get it at my houe but you can get it about 50 meters down the road on both side and i think this is completly unexseptible aspesaly as i was told my internet speed would be upgraded to 40 mb/s but i was told this in september of 2010 and it is now june 2011 what is tacking so long to lay 50 meters of wires because to be onet there is not any point for me paying for broardband when i am basicly getting dial up it is so bade it just took me 3 hours to download a flash update witch was 2mb this is totaly unesceptble and should be sorted asap or i will be forced to change provider in my despaire and fristration with this rediculas internet speed.

If you like post some information so other forum members ( BTcustomers) can offer some advice and if needed Moderators.
To post the full stats from your router
For homehub - 192.168.1.254
Navigate to ADSL Settings or use the A-Z at the top right
Click on More Details and then post the results.
Run Bt speed tester and post the results from http://speedtester.bt.com/
Mortgage Advisor 2000-2008
Green Energy Advisor 2008-2010
Charity Health Care Provider Advisor 2010-
I'm alright Jack....

Similar Messages

Lagg while video streaming

hi guys,
my video plays really laggy while i play from my laptop but if i use it from my ipad it doesnt.. so it means there is sumthing wrong with my browers or sumthing. can u guys tell me the solution for that please?
This question was solved.
View Solution.

Hello Kakarot:
Here is how to reset Google Crome back to default settings. It is on this page about half way down . Tittle of section is: Clean up your highjack settings. http://chrome.blogspot.com/ Ounce you down loaded Firefox and reset Google Crome to default settings. You are still experiencing slow play back. Then you need to contact your Internet provider and get Highspeed Iternet Speed. This is what I mean by difference in Ipod and computers Ipods use a different operating Internet speed. 100mbs or higher for Internet speeds I use Time Warner Cable my routers go through the cable line. The one that go through phone lines are much slower and more of a hassle to stay connected. Time Warner cost a little bit more but to me it hassle free and plenty of speed just with Basic TV and Regular high speed connectionn. If I want even supper high speed I can always up grade it. I do not know what is available in your erea. Here in Maine Time Warner is the best choice between the other three companies that are in my erea. frrw.
We did everything that is related to your computer. So it is your Internet speed is the issue.

Memory speed on T400

I have 2 ea. 2gb DDR3 PC-8500 1066Mhz memory modules installed in my T400. If I check the modules under Everest Ultimate 460 they read DDR2 running at 667 Mhz. If I use CPU-Z they also read DDR2 but don't show a speed. Has anyone else been able to check the speed of their modules and what program did you use? I don't see anything in the bios to cause the memory to run slower than rated. Do you think they are really running at 1066 MHz or do I have some type of compatibility problem. I get the same reading if I pull one of the modules out and check them one at a time.

Short answer, yes, the DDR3 memory bus in your T400/T500 should show at 533mhz(+/- 1mhz)
CPU-Z 1.51 will properly show as DDR3, previous versions may have incorrectly shown as DDR2
Here are your answers explianed in detail:
http://en.wikipedia.org/wiki/DDR3_SDRAM
T500 - P8600 2.4Ghz Core 2 Duo, Modded - 4GB Patriot DDR3 and 320GB Caviar Black 7200rpm drive with Ati HD3650 and Catalyst 9.6 modded drivers - Vista Business 32bit stripped down to bare bones with VM's from Ubuntu to Win7RC1 64-bit.

New FiOS GigE Wireless 'N' Router has slowed our wireless speed to a crawl...need help!

This past Tuesday I installed the new N router. Also, we upgraded to FiOS Quantum 75/35 (previously 15/5). That was activated the following day. I can't complain about the internet speed to our pc since it's wired. Speed tests showed we were getting what was advertised. :-)
For the wifi, I can't figured out for the life of me what's causing our devices (e.g., our Nexus 7 tablets) to have a link speeds of 65Mbps one minute and then drop down to 5 or even 1. The same situation was happening with my HTC Incredible II phone, but I think that connection was tapping out at 54Mbps. The bottom would just drop out of the signal for some reason. Other times we couldn't even connect back in. The devices would say they're not in range even when they were in front of the router. Not sure if I fubarred the router install or what? I just swapped out the current Fios router for this new one. Pretty straightforward. At first, I logged into the router software with the defaults, but then I changed the the username, pswd, SSID, etc. to match what I used previously. I thought it was working fine the night of the install but not so much after Fios got bumped up in speed the following day. Maybe just a co-inky-dink?
I know you never get the same speeds compared to a wired pc but this seems worse (wifi-wise) than before the new router came along. I've read that the 'N' routers can be finicky to set-up to run properly. Maybe a setting or two is off?
I don't know if the fact that my son's netbook's wifi card is only b/g compatible would slow our network down? At this point I'm grasping at straws! I talked with tech support last night for 40 mins to no avail. I got the usual story about wireless devices running slower than wired ones, that these smaller devices aren't capable to maintaining higher speeds (which I'm not sure I agree with 100%), the more active devices you have slows down your network, etc, etc. I get all that. But something is going on or actually, it's not. LOL!
Why I don't agree with the above statement I mentioned is because I have my tablet at work now and the wifi speed is 54Mbps and it's constant. So it seems to have no problems with this speed, unlike what I was told over the phone.
Let me know if I can provide any further technical details that'll make it easier to help diagnose our wifi issues.
Thanks for listening to me whine ,
-bill

Thanks for the help, Hubrisnxs.
Here's an update since I got home:
Nexus7 (N7) took a min or so to connect to wifi when I got home. When it did, speed said 65Mbps. So I ran speedtest.net and got 27/20. Shortly after that I tried again but it was hesitating. I checked the speed and it was down to 5Mbps. Brought it upstairs to router and pc, and eventually it was back to 65. Ran speed test a few more times with similar results. I did notice that the connection would intermittently come and go. Not sure why. Looking at the wifi section on my N7, it says our network is out of range and the N7 is 2' from the router. Every now and then my network will go to the top of the list and it'll say it's obtaining ip address, then secured with wpa/wpa2 psk and it's locked in. So I hit the connect button and it's out of range again. Of course, while I was typing it decided to connect after 10-15 mins of trying/nothing. Says, signal strength excellent, 52 Mbps. Spoke too soon. It's off again. Crap! Back on again but speed was 19, now 5.
I did check router settings and this is what I have:
Performance mode ('n')
WPA2 AES
Channel 1
nonbroadcasting SSID
Maybe I'll try channel 11 next.....
Just for the heck of it, here is the results from verizon speed test on our pc (wired of course):
Checking for Middleboxes . . . . . . . . . . . . . . . . . . Done
SendBufferSize set to [261360]
running 10s outbound test (client to server) . . . . . 34.66Mb/s
running 10s inbound test (server to client) . . . . . . 84.24Mb/s
------ Client System Details ------
OS data&colon; Name = Windows XP, Architecture = x86, Version = 5.1
Java data&colon; Vendor = Sun Microsystems Inc., Version = 1.6.0_37
------ Web100 Detailed Analysis ------
Client Receive Window detected at 1045440 bytes.
622 Mbps OC-12 link found.
Link set to Half Duplex mode
Information: throughput is limited by other network traffic.
Good network cable(s) found
Normal duplex operation found.
Web100 reports the Round trip time = 41.51 msec; the Packet size = 1452 Bytes; and
There were 72 packets retransmitted, 2254 duplicate acks received, and 2281 SACK blocks received
The connection was idle 0 seconds (0%) of the time
This connection is sender limited 91.83% of the time.
This connection is network limited 8.17% of the time.
Web100 reports TCP negotiated the optional Performance Settings to:
RFC 2018 Selective Acknowledgment: ON
RFC 896 Nagle Algorithm: ON
RFC 3168 Explicit Congestion Notification: OFF
RFC 1323 Time Stamping: OFF
RFC 1323 Window Scaling: ON
Information: Network Middlebox is modifying MSS variable
Server IP addresses are preserved End-to-End
Information: Network Address Translation (NAT) box is modifying the Client's IP address
Server says [] but Client says []
-bill

New VMS/IPC boxes - speed and pricing

For the most part, I've been a very happy FiOS customer. The internet side has gone out exactly once in the year I've had the service, and it was restored within an hour. TV has dropped out twice, both times very late at night (I assume for head-end maintenance). Reliability is better than every other ISP I've ever had, combined.
That said..
I wanted to snag another STB for the house - found out the local stores had all been closed (I can understand why from the financial aspect, but it was still a shock pulling up to my old store to pick up another STB.. and finding a "for lease" sign, when I'd been by there 2 months prior), so I looked at options online. The new VMS + IPC boxes looked promising, especially since they added the ability for the entire house to pause, rewind, schedule recordings, etc, from any TV - instead of only the DVR being able to do that (though the old boxes could stream recordings from the DVR).
My chief complaint so far - while the VMS box itself is responsive, the IPC boxes are painfully slow to respond to anything. Picture quality is fantastic, but using them feels, to put it in nerd terms, like using a Pentium 90 with Windows XP and 128MB RAM. They take 5+ to respond to anything more than a channel change (and even that takes up to 3 seconds), and frequently "lose" remote key presses if you try to, say, hit guide, hit page down, then try to arrow down to the channel that you know is on the next page. It literally feels like a throwback to the earliest digital set top boxes from Comcast/Time Warner - the first ones with built-in TV listings in the mid 1990s. The speed is right on par with them; the only thing faster right now is they don't shut down for 30 minutes a day to update the TV listings.
I've gone through the built-in diagnostics on the boxes to verify signal levels - they're decent (not perfect, but this is a 20 year old house with mostly original coax), but we have no pixelation or picture drop-out, so I would think they could carry the basic stuff between the IPC boxes and VMS pretty easily. The router certainly has no problem handling the 75/35 on the same coax (speedtest shows 85-90 down, 35-40 up, with a ~5ms ping, no matter which cable outlet it's plugged into)..
My other complaint - why did Verizon move to "rooms" for pricing? I thought I was getting a DVR plus 3 STBs (since I ordered 3 STBs and asked for a DVR), instead of a VMS + 2 STBs - and I'm paying much more than I did for the old DVR + 2 STBs.
With the griping out of the way - is there a reasonable chance that firmware updates will help with the speed of the IPC boxes? Or is there a chance it's a cabling issue? (I have no problem pulling new coax or cat5e, and I can provide signal levels if that'll help) If not, is there any chance of getting the old QIP7232 DVR + QIP7100 box back (and adding another 7100), and switching back to what I was paying before? I know they're a bit antiquated (especially the 7100s), but they were much more responsive, and didn't make me want to throw the STBs through the window. It just seems really rediculous that I'm paying such a large premium (plus the "upgrade fee") for equipment that, in terms of the user experience, is much worse.
Again.. been a happy customer for a long time, but the new terminals are super painful to use.
Thanks.

If this is the case. I think I will wait till the bugs are worked out
Question what were you paying before and after for the boxes. So what was the old DVR + 2 STB's and the new DVR plus 2 stb's
Trying to get an idea of what you meant by way more. Most people said same pricing and a small $20 or so upgrade fee

How to find the max data transfer rate(disk speed) supported by mobo?

I plan on replacing my current HDD with a new and bigger HDD.
For this I need to know the max data transfer rate(disk speed) that my mobo will support. However, dmidecode is not telling me that. Am I missing something?
Here's dmidecode:
# dmidecode 2.11
SMBIOS 2.5 present.
80 structures occupying 2858 bytes.
Table at 0x000F0450.
Handle 0xDA00, DMI type 218, 101 bytes
OEM-specific Type
Header and Data:
DA 65 00 DA B2 00 17 4B 0E 38 00 00 80 00 80 01
00 02 80 02 80 01 00 00 A0 00 A0 01 00 58 00 58
00 01 00 59 00 59 00 01 00 75 01 75 01 01 00 76
01 76 01 01 00 05 80 05 80 01 00 D1 01 19 00 01
00 15 02 19 00 02 00 1B 00 19 00 03 00 19 00 19
00 00 00 4A 02 4A 02 01 00 0C 80 0C 80 01 00 FF
FF 00 00 00 00
Handle 0xDA01, DMI type 218, 35 bytes
OEM-specific Type
Header and Data:
DA 23 01 DA B2 00 17 4B 0E 38 00 10 F5 10 F5 00
00 11 F5 11 F5 00 00 12 F5 12 F5 00 00 FF FF 00
00 00 00
Handle 0x0000, DMI type 0, 24 bytes
BIOS Information
Vendor: Dell Inc.
Version: A17
Release Date: 04/06/2010
Address: 0xF0000
Runtime Size: 64 kB
ROM Size: 4096 kB
Characteristics:
PCI is supported
PNP is supported
APM is supported
BIOS is upgradeable
BIOS shadowing is allowed
ESCD support is available
Boot from CD is supported
Selectable boot is supported
EDD is supported
Japanese floppy for Toshiba 1.2 MB is supported (int 13h)
3.5"/720 kB floppy services are supported (int 13h)
Print screen service is supported (int 5h)
8042 keyboard services are supported (int 9h)
Serial services are supported (int 14h)
Printer services are supported (int 17h)
ACPI is supported
USB legacy is supported
BIOS boot specification is supported
Function key-initiated network boot is supported
Targeted content distribution is supported
BIOS Revision: 17.0
Handle 0x0100, DMI type 1, 27 bytes
System Information
Manufacturer: Dell Inc.
Product Name: OptiPlex 755
Version: Not Specified
UUID: 44454C4C-5900-1050-8033-C4C04F434731
Wake-up Type: Power Switch
SKU Number: Not Specified
Family: Not Specified
Handle 0x0200, DMI type 2, 8 bytes
Base Board Information
Manufacturer: Dell Inc.
Product Name: 0PU052
Version:
Handle 0x0300, DMI type 3, 13 bytes
Chassis Information
Manufacturer: Dell Inc.
Type: Space-saving
Lock: Not Present
Version: Not Specified
Asset Tag:
Boot-up State: Safe
Power Supply State: Safe
Thermal State: Safe
Security Status: None
Handle 0x0400, DMI type 4, 40 bytes
Processor Information
Socket Designation: CPU
Type: Central Processor
Family: Xeon
Manufacturer: Intel
ID: 76 06 01 00 FF FB EB BF
Signature: Type 0, Family 6, Model 23, Stepping 6
Flags:
FPU (Floating-point unit on-chip)
VME (Virtual mode extension)
DE (Debugging extension)
PSE (Page size extension)
TSC (Time stamp counter)
MSR (Model specific registers)
PAE (Physical address extension)
MCE (Machine check exception)
CX8 (CMPXCHG8 instruction supported)
APIC (On-chip APIC hardware supported)
SEP (Fast system call)
MTRR (Memory type range registers)
PGE (Page global enable)
MCA (Machine check architecture)
CMOV (Conditional move instruction supported)
PAT (Page attribute table)
PSE-36 (36-bit page size extension)
CLFSH (CLFLUSH instruction supported)
DS (Debug store)
ACPI (ACPI supported)
MMX (MMX technology supported)
FXSR (FXSAVE and FXSTOR instructions supported)
SSE (Streaming SIMD extensions)
SSE2 (Streaming SIMD extensions 2)
SS (Self-snoop)
HTT (Multi-threading)
TM (Thermal monitor supported)
PBE (Pending break enabled)
Version: Not Specified
Voltage: 0.0 V
External Clock: 1333 MHz
Max Speed: 5200 MHz
Current Speed: 2666 MHz
Status: Populated, Enabled
Upgrade: Socket LGA775
L1 Cache Handle: 0x0700
L2 Cache Handle: 0x0701
L3 Cache Handle: Not Provided
Serial Number: Not Specified
Asset Tag: Not Specified
Part Number: Not Specified
Core Count: 2
Core Enabled: 2
Thread Count: 2
Characteristics:
64-bit capable
Handle 0x0700, DMI type 7, 19 bytes
Cache Information
Socket Designation: Not Specified
Configuration: Enabled, Not Socketed, Level 1
Operational Mode: Write Back
Location: Internal
Installed Size: 32 kB
Maximum Size: 32 kB
Supported SRAM Types:
Other
Installed SRAM Type: Other
Speed: Unknown
Error Correction Type: None
System Type: Data
Associativity: 8-way Set-associative
Handle 0x0701, DMI type 7, 19 bytes
Cache Information
Socket Designation: Not Specified
Configuration: Enabled, Not Socketed, Level 2
Operational Mode: Varies With Memory Address
Location: Internal
Installed Size: 6144 kB
Maximum Size: 6144 kB
Supported SRAM Types:
Other
Installed SRAM Type: Other
Speed: Unknown
Error Correction Type: Single-bit ECC
System Type: Unified
Associativity: <OUT OF SPEC>
Handle 0x0800, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: PARALLEL
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: DB-25 female
Port Type: Parallel Port PS/2
Handle 0x0801, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: SERIAL1
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: DB-9 male
Port Type: Serial Port 16550A Compatible
Handle 0x0802, DMI type 126, 9 bytes
Inactive
Handle 0x0803, DMI type 126, 9 bytes
Inactive
Handle 0x0804, DMI type 126, 9 bytes
Inactive
Handle 0x0805, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB1
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x0806, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB2
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x0807, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB3
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x0808, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB4
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x0809, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB5
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x080A, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB6
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x080B, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB7
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x080C, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: USB8
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Access Bus (USB)
Port Type: USB
Handle 0x080D, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: ENET
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: RJ-45
Port Type: Network Port
Handle 0x080E, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: MIC
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Mini Jack (headphones)
Port Type: Audio Port
Handle 0x080F, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: LINE-OUT
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Mini Jack (headphones)
Port Type: Audio Port
Handle 0x0810, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: LINE-IN
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Mini Jack (headphones)
Port Type: Audio Port
Handle 0x0811, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: HP-OUT
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: Mini Jack (headphones)
Port Type: Audio Port
Handle 0x0812, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: MONITOR
Internal Connector Type: None
External Reference Designator: Not Specified
External Connector Type: DB-15 female
Port Type: Video Port
Handle 0x090A, DMI type 9, 13 bytes
System Slot Information
Designation: SLOT1
Type: x1 Proprietary
Current Usage: In Use
Length: Long
Characteristics:
PME signal is supported
Handle 0x0901, DMI type 126, 13 bytes
Inactive
Handle 0x0902, DMI type 9, 13 bytes
System Slot Information
Designation: SLOT2
Type: 32-bit PCI
Current Usage: Available
Length: Long
ID: 2
Characteristics:
5.0 V is provided
3.3 V is provided
PME signal is supported
Handle 0x0903, DMI type 126, 13 bytes
Inactive
Handle 0x0904, DMI type 126, 13 bytes
Inactive
Handle 0x0905, DMI type 126, 13 bytes
Inactive
Handle 0x0906, DMI type 126, 13 bytes
Inactive
Handle 0x0907, DMI type 126, 13 bytes
Inactive
Handle 0x0908, DMI type 126, 13 bytes
Inactive
Handle 0x0A00, DMI type 10, 6 bytes
On Board Device Information
Type: Video
Status: Disabled
Description: Intel Graphics Media Accelerator 950
Handle 0x0A02, DMI type 10, 6 bytes
On Board Device Information
Type: Ethernet
Status: Enabled
Description: Intel Gigabit Ethernet Controller
Handle 0x0A03, DMI type 10, 6 bytes
On Board Device Information
Type: Sound
Status: Enabled
Description: Intel(R) High Definition Audio Controller
Handle 0x0B00, DMI type 11, 5 bytes
OEM Strings
String 1: www.dell.com
Handle 0x0D00, DMI type 13, 22 bytes
BIOS Language Information
Language Description Format: Long
Installable Languages: 1
en|US|iso8859-1
Currently Installed Language: en|US|iso8859-1
Handle 0x0F00, DMI type 15, 29 bytes
System Event Log
Area Length: 2049 bytes
Header Start Offset: 0x0000
Header Length: 16 bytes
Data Start Offset: 0x0010
Access Method: Memory-mapped physical 32-bit address
Access Address: 0xFFF01000
Status: Valid, Not Full
Change Token: 0x00000018
Header Format: Type 1
Supported Log Type Descriptors: 3
Descriptor 1: POST error
Data Format 1: POST results bitmap
Descriptor 2: System limit exceeded
Data Format 2: System management
Descriptor 3: Log area reset/cleared
Data Format 3: None
Handle 0x1000, DMI type 16, 15 bytes
Physical Memory Array
Location: System Board Or Motherboard
Use: System Memory
Error Correction Type: None
Maximum Capacity: 8 GB
Error Information Handle: Not Provided
Number Of Devices: 4
Handle 0x1100, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x1000
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 1024 MB
Form Factor: DIMM
Set: None
Locator: DIMM_1
Bank Locator: Not Specified
Type: DDR2
Type Detail: Synchronous
Speed: 667 MHz
Manufacturer: AD00000000000000
Handle 0x1101, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x1000
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 1024 MB
Form Factor: DIMM
Set: None
Locator: DIMM_3
Bank Locator: Not Specified
Type: DDR2
Type Detail: Synchronous
Speed: 667 MHz
Handle 0x1102, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x1000
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 1024 MB
Form Factor: DIMM
Set: None
Locator: DIMM_2
Bank Locator: Not Specified
Type: DDR2
Type Detail: Synchronous
Speed: 667 MHz
Handle 0x1103, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x1000
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 1024 MB
Form Factor: DIMM
Set: None
Locator: DIMM_4
Bank Locator: Not Specified
Type: DDR2
Type Detail: Synchronous
Speed: 667 MHz
Handle 0x1300, DMI type 19, 15 bytes
Memory Array Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x000FDFFFFFF
Range Size: 4064 MB
Physical Array Handle: 0x1000
Partition Width: 1
Handle 0x1400, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x0007FFFFFFF
Range Size: 2 GB
Physical Device Handle: 0x1100
Memory Array Mapped Address Handle: 0x1300
Partition Row Position: 1
Interleave Position: 1
Interleaved Data Depth: 1
Handle 0x1401, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00080000000
Ending Address: 0x000FDFFFFFF
Range Size: 2016 MB
Physical Device Handle: 0x1101
Memory Array Mapped Address Handle: 0x1300
Partition Row Position: 1
Interleave Position: 1
Interleaved Data Depth: 1
Handle 0x1402, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x0007FFFFFFF
Range Size: 2 GB
Physical Device Handle: 0x1102
Memory Array Mapped Address Handle: 0x1300
Partition Row Position: 1
Interleave Position: 2
Interleaved Data Depth: 1
Handle 0x1403, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00080000000
Ending Address: 0x000FDFFFFFF
Range Size: 2016 MB
Physical Device Handle: 0x1103
Memory Array Mapped Address Handle: 0x1300
Partition Row Position: 1
Interleave Position: 2
Interleaved Data Depth: 1
Handle 0x1410, DMI type 126, 19 bytes
Inactive
Handle 0x1800, DMI type 24, 5 bytes
Hardware Security
Power-On Password Status: Enabled
Keyboard Password Status: Not Implemented
Administrator Password Status: Enabled
Front Panel Reset Status: Not Implemented
Handle 0x1900, DMI type 25, 9 bytes
System Power Controls
Next Scheduled Power-on: *-* 00:00:00
Handle 0x1B10, DMI type 27, 12 bytes
Cooling Device
Type: Fan
Status: OK
OEM-specific Information: 0x0000DD00
Handle 0x1B11, DMI type 27, 12 bytes
Cooling Device
Type: Fan
Status: OK
OEM-specific Information: 0x0000DD01
Handle 0x1B12, DMI type 126, 12 bytes
Inactive
Handle 0x1B13, DMI type 126, 12 bytes
Inactive
Handle 0x1B14, DMI type 126, 12 bytes
Inactive
Handle 0x2000, DMI type 32, 11 bytes
System Boot Information
Status: No errors detected
Handle 0x8100, DMI type 129, 8 bytes
OEM-specific Type
Header and Data:
81 08 00 81 01 01 02 01
Strings:
Intel_ASF
Intel_ASF_001
Handle 0x8200, DMI type 130, 20 bytes
OEM-specific Type
Header and Data:
82 14 00 82 24 41 4D 54 01 01 00 00 01 A5 0B 02
00 00 00 00
Handle 0x8300, DMI type 131, 64 bytes
OEM-specific Type
Header and Data:
83 40 00 83 14 00 00 00 00 00 C0 29 05 00 00 00
F8 00 4E 24 00 00 00 00 0D 00 00 00 02 00 03 00
19 04 14 00 01 00 01 02 C8 00 BD 10 00 00 00 00
00 00 00 00 FF 00 00 00 00 00 00 00 00 00 00 00
Handle 0x8800, DMI type 136, 6 bytes
OEM-specific Type
Header and Data:
88 06 00 88 5A 5A
Handle 0xD000, DMI type 208, 10 bytes
OEM-specific Type
Header and Data:
D0 0A 00 D0 01 03 FE 00 11 02
Handle 0xD100, DMI type 209, 12 bytes
OEM-specific Type
Header and Data:
D1 0C 00 D1 78 03 07 03 04 0F 80 05
Handle 0xD200, DMI type 210, 12 bytes
OEM-specific Type
Header and Data:
D2 0C 00 D2 F8 03 04 03 06 80 04 05
Handle 0xD201, DMI type 126, 12 bytes
Inactive
Handle 0xD400, DMI type 212, 242 bytes
OEM-specific Type
Header and Data:
D4 F2 00 D4 70 00 71 00 00 10 2D 2E 42 00 11 FE
01 43 00 11 FE 00 0F 00 25 FC 00 10 00 25 FC 01
11 00 25 FC 02 12 00 25 FC 03 00 00 25 F3 00 00
00 25 F3 04 00 00 25 F3 08 00 00 25 F3 0C 07 00
23 8F 00 08 00 23 F3 00 09 00 23 F3 04 0A 00 23
F3 08 0B 00 23 8F 10 0C 00 23 8F 20 0E 00 23 8F
30 0D 00 23 8C 40 A6 00 23 8C 41 A7 00 23 8C 42
05 01 22 FD 02 06 01 22 FD 00 8C 00 22 FE 00 8D
00 22 FE 01 9B 00 25 3F 40 9C 00 25 3F 00 09 01
25 3F 80 A1 00 26 F3 00 A2 00 26 F3 08 A3 00 26
F3 04 9F 00 26 FD 02 A0 00 26 FD 00 9D 00 11 FB
04 9E 00 11 FB 00 54 01 23 7F 00 55 01 23 7F 80
5C 00 78 BF 40 5D 00 78 BF 00 04 80 78 F5 0A 01
A0 78 F5 00 93 00 7B 7F 80 94 00 7B 7F 00 8A 00
37 DF 20 8B 00 37 DF 00 03 C0 67 00 05 FF FF 00
00 00
Handle 0xD401, DMI type 212, 172 bytes
OEM-specific Type
Header and Data:
D4 AC 01 D4 70 00 71 00 03 40 59 6D 2D 00 59 FC
02 2E 00 59 FC 00 6E 00 59 FC 01 E0 01 59 FC 03
28 00 59 3F 00 29 00 59 3F 40 2A 00 59 3F 80 2B
00 5A 00 00 2C 00 5B 00 00 55 00 59 F3 00 6D 00
59 F3 04 8E 00 59 F3 08 8F 00 59 F3 00 00 00 55
FB 04 00 00 55 FB 00 23 00 55 7F 00 22 00 55 7F
80 F5 00 58 BF 40 F6 00 58 BF 00 EB 00 55 FE 00
EA 00 55 FE 01 40 01 54 EF 00 41 01 54 EF 10 ED
00 54 F7 00 F0 00 54 F7 08 4A 01 53 DF 00 4B 01
53 DF 20 4C 01 53 7F 00 4D 01 53 7F 80 68 01 56
BF 00 69 01 56 BF 40 FF FF 00 00 00
Handle 0xD402, DMI type 212, 152 bytes
OEM-specific Type
Header and Data:
D4 98 02 D4 70 00 71 00 00 10 2D 2E 2D 01 21 FE
01 2E 01 21 FE 00 97 00 22 FB 00 98 00 22 FB 04
90 00 11 CF 00 91 00 11 CF 20 92 00 11 CF 10 E2
00 27 7F 00 E3 00 27 7F 80 E4 00 27 BF 00 E5 00
27 BF 40 D1 00 22 7F 80 D2 00 22 7F 00 45 01 22
BF 40 44 01 22 BF 00 36 01 21 F1 06 37 01 21 F1
02 38 01 21 F1 00 39 01 21 F1 04 2B 01 11 7F 80
2C 01 11 7F 00 4E 01 65 CF 00 4F 01 65 CF 10 D4
01 65 F3 00 D5 01 65 F3 04 D2 01 65 FC 00 D3 01
65 FC 01 FF FF 00 00 00
Handle 0xD403, DMI type 212, 157 bytes
OEM-specific Type
Header and Data:
D4 9D 03 D4 70 00 71 00 03 40 59 6D 17 01 52 FE
00 18 01 52 FE 01 19 01 52 FB 00 1A 01 52 FB 04
1B 01 52 FD 00 1C 01 52 FD 02 1D 01 52 F7 00 1E
01 52 F7 08 1F 01 52 EF 00 20 01 52 EF 10 21 01
52 BF 00 22 01 52 BF 40 87 00 59 DF 20 88 00 59
DF 00 E8 01 66 FD 00 E9 01 66 FD 02 02 02 53 BF
00 03 02 53 BF 40 04 02 53 EF 00 05 02 53 EF 10
06 02 66 DF 00 07 02 66 DF 20 08 02 66 EF 00 09
02 66 EF 10 17 02 66 F7 00 18 02 66 F7 08 44 02
52 BF 40 45 02 52 BF 00 FF FF 00 00 00
Handle 0xD800, DMI type 126, 9 bytes
Inactive
Handle 0xDD00, DMI type 221, 19 bytes
OEM-specific Type
Header and Data:
DD 13 00 DD 00 01 00 00 00 10 F5 00 00 00 00 00
00 00 00
Handle 0xDD01, DMI type 221, 19 bytes
OEM-specific Type
Header and Data:
DD 13 01 DD 00 01 00 00 00 11 F5 00 00 00 00 00
00 00 00
Handle 0xDD02, DMI type 221, 19 bytes
OEM-specific Type
Header and Data:
DD 13 02 DD 00 01 00 00 00 12 F5 00 00 00 00 00
00 00 00
Handle 0xDE00, DMI type 222, 16 bytes
OEM-specific Type
Header and Data:
DE 10 00 DE C1 0B 00 00 10 05 19 21 01 00 00 01
Handle 0x7F00, DMI type 127, 4 bytes
End Of Table
Hdparm also does not tell me the max data transfer rate (disk speed) of my current drive although this link : www.wdc.com/en/library/sata/2879-001146.pdf says that it is 3.0Gb/s
and here's hdparm -I /dev/sda
/dev/sda:
ATA device, with non-removable media
Model Number: WDC WD800JD-75JNC0
Firmware Revision: 06.01C06
Standards:
Supported: 6 5 4
Likely used: 8
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
CHS current addressable sectors: 16514064
LBA user addressable sectors: 156250000
Logical/Physical Sector size: 512 bytes
device size with M = 1024*1024: 76293 MBytes
device size with M = 1000*1000: 80000 MBytes (80 GB)
cache/buffer size = 8192 KBytes
Capabilities:
LBA, IORDY(can be disabled)
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 8
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* DOWNLOAD_MICROCODE
SET_MAX security extension
Automatic Acoustic Management feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* SMART error logging
* SMART self-test
* Gen1 signaling speed (1.5Gb/s)
* Host-initiated interface power management
* SMART Command Transport (SCT) feature set
* SCT Long Sector Access (AC1)
* SCT LBA Segment Access (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
not supported: enhanced erase
Checksum: correct
Last edited by Inxsible (2011-03-27 04:40:49)

I just checked my BIOS and my current setting is set at IDE although it also mentions that the default should be AHCI. Currently I have a dual boot of Windows 7 (need it for Tax software) and Arch
So I guess, when I get the new HDD, I will first set it to AHCI and then install the OSes on it. See if NCQ helps any, and if not I will turn it back and re-install (if I have to). I am planning to have Windows only in virtualbox in the new drive.
Anyhoo, while I was in the BIOS I found two things which I had questions about :
1) Under Onboard Devices --> Integrated NIC , my setting is currently set at "On w/PXE" and it says the default should be just "On". Would it be ok to change it back to On since its a single machine and its not booting an OS on any server. I just don't want to have to re-install anything now since I will be doing that in the new HDD.
2) How would I know whether my BIOS would support a 64 bit OS in Virtualbox? I checked some setting under Virtualization, but they weren't very clear.
I will edit this post and let you know exactly what settings were present under the Virtualization sub-section.

Is there a way to speed up video clips in imovie on ipad

is there a way to speed up video clips in imovie on ipad? I'm currently editing some videos and would like to speed up a few clips to make the video shorter. Is this possible on ipad or just mac pcs only?

actually, no 'add-ons' possible or avail for iMovie/MacOS/iOS…

T61 - Half theCore speed at maximum performance mode.

Hello,
My T61 was bought during March 2008. I recently installed CPU-Z and was bit worried since under maximum performance mode, the CPU was not throttling to full speed (with AC power).
The core speed is showing approximately 1200MHz. FSB is showing around 800Mhz. It is a penryn T9300 processor and I believe it should be 2500Mhz. Is there a setting somewhere on the power options that needs to configured to attain the maximum core speed? OS is XP SP3 clean install.
Thanks for any help,
Regards,
Thanimai

You have to actually put quite some load to get the machine to work at its full throttle...while I'm typing this my ThinkPad is showing a core speed of 1199Mhz (it's a P4M 2.0) and trust you me, it would take quite a bit to get it up to the max, and your CPU is far newer and can take a lot more without shooting up...
Hope this helps.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

Who has the Unlimited Data Plan and has Been Speed Capped when You went over 5Gig?

Just checking to see how many others have been speed capped to 200Kb on the unlimited data plan when they went over 5Gig in a billing cycle? (you can get a one time reprieve if you call them at 1-888-483-7200)
Did they ask you to change your plan to 10Gig and Update your Equipment and sign a new two year agreement?
Did you know that Sprint is offering unlimited Data on their 4G network and that Verizon is trying to lock down customers that are not on 2 year contracts? (Gives them time to catch up with the competition) Marcus in Fraud and Investigation told me (when I told him that Sprint was offering Unlimited Data) "...That is a better option..."
I am now looking into other options along with allot of the rest of you.

I was instructed to call that Fraud Department number and was treated like I had broken some kind of law instead of going over the 5 Gig fine print limit on my unlimited grandfathered in account. They would not even consider giving me a one time do over for being a MiFi newbie. I am hearing class action suit rumblings out there!!

Java3d speed collapse caused by other java apps running at the same time

Hi
I am programming a flightsimulator for some months.
The current state is online available (all free, no copyrights)
at http://www.snowraver.org/efcn/efcnsim/index.htm
especially the sample (source) which shows the
behaviour which is the reason for my post is here
http://www.snowraver.org/efcn/efcnsim/page2.htm
My Problem:
When I start the sim while two other java programs
( one is a server running localhost, one is a client )
are running, the speed of the flightsim is very slow,
one frame update takes 3 to 5 seconds.
( 3 java.exe's in task list plus 1 which is the IDE )
When I start the flightsim ALONE, I have 30 to 40 frames per second.
( 2 java.exe's in the task list = the flightsim and the IDE -> no prob here )
That means, the flightsim is about 100 times slower, when
started while the other two apps are running.
BUT the other two applications do almost ***NOTHING***, the
CPU load is 1 or 2 percent.
Of course they have threads running, but all are waiting
for a signal - no thread really consumes CPU power.
Interestingly, when I FIRST start the flightsim and AFTER THIS
start the two other applications, the flightsim
holds 30 frames per seconds without problems, even
though the other applications consume some CPU power
until they have completely started up.
Configurations:
JSDK 1.4.2_1 , 0_2..
Java3D 1.3.1 OPENGL (The DirectX version crashes with D3D device lost)
Win2000,XP CPU 800MHz upto 3 GHz
In my point of view, the java3d thread scheduler makes
some funny decisions when it starts up, which lead
to the order dependent behaviour described above.
My question is, if anyone has some ideas, how I could
get away from this speed collapse.
The problem is caused in native code I guess.
I also could imagine, that it has to do something with
the order in which one creates, attaches and starts
the Canvas3D. (? could produce race conditions)
The flightsim runs in full retained mode. Of course
the CPU work in the behaviours is rather big, because
the ROAM triangulation update (..) is done there
and the triangles are recalculated and passed
( all BY_REFERENCE ).
Or could it have to do something with the memory
consumption ( when all runs, almost all of
the 512MB RAM is taken by the three java.exe's ) ?
Any hints or ideas ?

:) No, Sun does handle it [lol]
I just have tested it on my computer at work
( 3GHz HP compaq, 1GB Ram and a Intel 82865G Graphics
Card with 64MB memory, Windows XP )
and it has worked without problems any way I tried.
( Except for xclusive fullscreen mode, but I guess, the administrators
have deactivated it somehow, so we don't play games at work :)
I couldn't test it under Linux so far, but I think, this will be less
problematic than Windows [usually].
However my current assumption is:
I totally have forgot the [limited] videocard memory.
I suppose, Java3D tries to put all triangle data and all
textures to the videocards memory, so most data processing
then can be passed to it's graphiccard CPU using
OpenGL commands.
Now the flightsim produces a varying amount of (by_reference) triangle data ( a few thousands )
and has some texture maps for the terrain, the sea and other things,
plus indexed triangle data for the planes and ships.
The notebook system, which slows down has an ATI Mobile Radeon card
with only 32MB RAM onboard, whereas the others have 64MB Ram.
An additional pointer to that theory is that I can trigger the slowdown by resizing
the flightsim window, while it is running.
On the notebook, it holds 30fps, until the window exceeds a size of 962*862 pixels.
At this size the speed collapses and goes down to 1 frame update every 4 seconds.
If I make the window a few pixels smaller, the speed of 30fps immediately
is there again.
Therefore I guess, some data passed to the graphic cards memory depends
linearly from the canvas3d's window dimension, and at some limit,
the graphiccard's memory is too small and Java3D changes it's strategy
and performs most calculations on the computer's mainmemory,
which of course is a lot slower.
I'm not very sure about that, I'm just speculating.
Next thing I will try is to disable directdraw for the other two applications,
possibly swing also uses graphicscard memory, when directdraw is enabled.
The solution seems to be clear anyway: The flightsim must examine the system
and set some parameters depending on the machine's capabilities.
Onboard videagraphic ram is one of them. If it's too slow, I start to decrease
the window size and expect to see a sudden increase of speed, as soon as
the rendering can be done by the graphicscard CPU. If this never happens,
I assume no OpenGL accelerator is present on that system. This can be seen as a method
for finding out the amount of videocard memory on a system by trial and error ..?:)
Thanks for your tips, Alain.
I especially have to check out the data sharing class in 1.5.

How do I install OSX onto a new SSD (in the place of my optical drive) without transferring all data across. However, with the applications, system and library on the SSD to improve the speed, but keep non essential items (the home folder) on the HDD

I have a mid 2009 13 inch unibody 2.53GHz MacBook Pro. I'm finding that it doesn't run as quickly as it used to.
A genius in the Apple store suggested that I replace my optical drive with an SSD, however only use the SSD for OSX, applications, system and library. Keep all documents, pictures, music etc on the current hard drive.
I would be grateful if someone could help me with:
1) installing OSX on the SSD without copying across data from the current hard drive
2) transferring applications, system and library folders across to the SSD so that they still function
3) changing my settings so that OSX reads the home folder from the current hard drive, as well as all the applications' data (documents, music etc...)
However, I would like to run iMovie, with all events etc solely from the SSD to speed up the process of editing movies.
If anyone could help with this, it would be much appreciated.

If you got the data transfer cable with your SSD, the procedure should be pretty simple - and there should be step-by-step instructions in the box. You're simply going to remove the bottom case of your computer (using a Phillips #00 screwdriver), take out the two screws in the bracket holding the hard drive into place (using same screwdriver), remove the drive and (use a Torx 6 screwdriver) remove the four screws that hold the hard drive in place. Then put in the SSD and reassemble the machine.
Then you'll plug up the old hard drive by using the SATA to USB cable and use the option key to boot from the old drive. I don't know what data transfer software Crucial provides, but I would recommend formatting the SSD using Disk Utility from your old drive ("Mac OS Extended (Journaled)" with a single GUID partition) and then use Carbon Copy Cloner to clone your old drive to your new SSD (see this user tip for cloning - https://discussions.apple.com/docs/DOC-4122). You needn't worry about getting an enclosure since you have the data transfer cable and you don't want to use your old hard drive.
There are a number of videos on YouTube that take you step-by-step through this procedure - many specific to Crucial SSDs and their data transfer kit - do a little searching there if you're unsure of how to procede.
Clinton

Sometimes my computer takes too long to connect to new website. I am running a pretty powerful work program at same time, what is the best solution? Upgrading speed from cable network, is it a hard drive issue? do I need to "clean out" the computer?

Many times my computer takes too long to connect to new website. I have wireless internet (time capsule) and I am running a pretty powerful real time financial work program at same time, what is the best solution? Upgrading speed from cable network? is it a hard drive issue? do I only need to "clean out" the computer? Or all of the above...not to computer saavy. It is a Macbook Pro osx 10.6.8 (late 2010).

Almost certainly none of the above! Try each of the following in this order:
Select 'Reset Safari' from the Safari menu.
Close down Safari; move <home>/Library/Caches/com.apple.Safari/Cache.db to the trash; restart Safari.
Change the DNS servers in your network settings to use the OpenDNS servers: 208.67.222.222 and 208.67.220.220
Turn off DNS pre-fetching by entering the following command in Terminal and restarting Safari:
defaults write com.apple.safari WebKitDNSPrefetchingEnabled -boolean false

Upgrading my intel iMac to internal SSD and running 1TB external drive from firewire 800 for mass storage while still using a second external drive for backups...my goal-speed with a SSD, to still have 1TB of room for everything i have now..possible?

I seem to kill HD's every two years...the last two i've installed were WD Caviar Black 1TB 7200rpm 3.5" drives. The speed gains over stock drives have been remarkable. I don't blame the drives for the failures, my machines are up and running 16 hours a day, every day, year round. They die from 'mileage' so to speak...i assume...there's no viral acvtivity or questionable downloads to gunk things up...just lots of work.
I have my third new drive ready to install in my intel based iMac...but i've had a thought...I want to install a SSD in my iMac for the speed gain (and recent price drops)...for standard storage i want to use this new WD Caviar Black 1TB in an external drive bay and connect via firewire 800 for storing everything except the OS and my most commonly used software...am i crazy? will the firewire 800 external drive negate the speed gained with an internal SSD??
I have four iMacs in my office, and one at home. I buy second hand and install new drives and boost memory. I'm going to do this on my 'home' machine...if it works out well i want to upgrade the other three this way...but first i need to know if i'm just dreaming, or will it really make a difference? or even possible??
Thanks!
2.66 intell core2duo
2009 iMac
8gig ram
1 gig hd
OSX ver. 10.8

The SSD gives great bootup and Application launch speed. I think it also speeds up the video rendering a bit, I do all that on the SSD and then move the finished project to the external drives. As far as the speed for the external drives they are quick enough for viewing video and the file transfer rate is good. I had initially put the SSD into an external cradle (FW800) and the system was faster than on the internal drive. I only got a 1.5GBs SATA drive, perhaps yours could benefit from the 3GBs. I know the 6GBs would be too fast and costs a lot more, even the MacPros need special hookups to make use of the 6GBs.

Do I need to have an external hard drive that has a certain spindle speed, like 7200?

In the past, when I did audio or video editing, the specs on the software required a certain rotational speed if I were using an external hard drive. Most of the time it was 7200. Do I need to use a specific spindle rotational speed for Final Cut Pro, or will drive 5400 or above do fine?

That still applies today as well. Helps to also use faster connection ports like Firewire 400 or 800, USB 3.0, or Thunderbolt rather than USB 2.0.

Photo Gallery Speed in iWeb Site

Hi, I'm looking for some advice on quicker photo galleries.
I've made my organization's website using iWeb... It seems to work fine, except a lot of the site is really slow to load, especially large photo galleries. I realize a lot of this has to do with the code, but is there another solution (have the photo's hosted by some other, faster service)?
See for yourself: http://turtleconservancy.org/travel/brazil/
Thanks for your help!
Max

Hi guys, thanks for taking a look. The site is made with iWeb. The gallery was made by drag n drop + linking to image files, then adding the shadow box code in Dreamweaver.
When I said the site is slow to load, I am just looking to speed it up. It loads fine on every test machine i've used. I'm just looking to make it even faster! (Google Analytics is telling me it's slow...)
-If I hosted the linked images on another server (amazon cloud) would this speed things up?
-Is there another way to present a gallery of images with captions + shadow box (or similar, elegant) effect that would cut down the load time?
Also, a bit off topic, anyone know of a good resource to read up on taking advantage of browser cache capabilities and how to make a section of the site (ie. navbar) an "include"?
As you can clearly see, I am no pro... Haha! Any other streamlining/optimization tips are greatly appreciated!
Again, the site I'm working with here is: http://turtleconservancy.org/
Thank you for all help and advice!
-Max

Iternet speed

Similar Messages

Maybe you are looking for